I cannot open router settings... I had recently opened some ports on my router. However today I tried to access the settings and all it does is a web search for the gateway (192.168.1.254). The internet is working. I reset the router and it did not work. I cannot do a hard reset because I will lose all my settings for my company's settings. Also the router is a Netopia modem/router
View 2 RepliesI cannot open the config page of beetel adsl2 router using 192.168.1.1I have connected my laptop to router via Lan cable. Now when I give the ipconfig, I get some random IP and does not get the default gateway: Autoconfiguration IPv4 Address. . : 169.254.129.188 Subnet Mask . . . . . . . . . . . : 255.255.0.0 Default Gateway . . . . . . . . . :I cannot ping 192.168.1.1 nor 169.254.129.1 thus the web page of router cannot be opened.This all happened after I reset my router.
View 3 Replies View RelatedI've been trying to set up my TP-Link WR740N router but it always give the error "Failed to Verify router settings" on the last step of the set up screen. Broadband: Globe broadband (Wired)Modem: Siemen Gigaset SE260 I'm also confused on the 2nd Set up screen, it gives the option to select Dynamic IP Static IP PPoEI've tried using the Dynamic IP and PPoE but still getting the same error message
View 1 Replies View Relatedto enable UPNP on a Virgin Media Super Hub, I have tried using both the IP addresses provided by Virgin media (192.168.0.1 and 192.168.100.1) but regardless of which browser I use the page constantly fails to load.
View 2 Replies View Relatedi recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies View RelatedHow do FPS's open UDP ports without needing to configure the router to forward them?I never have to forward ports from my router to my PC. Every game i have somehow manages to open the UDP ports it needs without me having to configure my router. Yet when i check to see if those ports are open (prior to starting the programs) they always come back as blocked or closed. Now I'm currently working on a UDP Internet program and need to know how to do the same thing - open ports on a router without having to make the customer configure their routers. I'm THINKING that other programs start with a TCP/IP connection on the desired port and that opens the UDP port. Is this the answer or is there another method used?
View 5 Replies View Relatedto access VOD database i must open three ports on the router - not sure how to
View 3 Replies View RelatedWhen checking my port forwarding, it says that it is not open.
View 2 Replies View RelatedFor some port fowarding reasons I have to change my router setting to these:Maximum Ports: 4096TCP Timeout (in seconds): 600UCP Timeout (in seconds): 120I am using a Realtek router ( Family PCI-E Gigabit Ethernet <NDIS 6.20>)This is supposed to be EXTREMELY easy but I lack any general computer knowledge whatsoever. In laymen's term, I am N00B.
View 1 Replies View Relatedhow to open the tp-link interface setup for my TD-W896ON? i have a user and a password but where do i add them ??
View 1 Replies View RelatedI have just upgraded my AIM and Skype messengers and now it won't let me sign in. I did before with my old versions. It is saying that my internet connection is bad which it is not. I have looked up ports in my Yahoo messengers, Control Panel and Bit Torrent still nothing.
View 6 Replies View Relatedhow do i open a port on Motorola modem
View 1 Replies View RelatedWhen checking my port forwarding, it says that it is not open. Why?
View 6 Replies View RelatedI just recently upgraded my router from the WRT160n V3 to the E3000. I had to port forward from my old 160n to get my NAT settings from Xbox Live set to OPEN. When I switched out the router to the new E3000, my Xbox Live settings went back to Medium (Moderate). I assumed this would happend since its a new router/setup.
setup my E3000 and Xbox Live so I can have my NAT settings to OPEN? I only need to setup 1 Xbox.
I'm using a Thomson Technicolor 587nV3. I need to change my NAT status from strict to open. So I can play MW3 online and connect to my friends online games and so I can host multiplayer matches. I have windows 7 laptop to do any of the steps required. I've tried to bind my routers cone through Winscript but without any luck perhaps I done it wrong
View 5 Replies View RelatedI was just recently hired in my company, we have an sf300-24p switch but I cant find the console cable for it, I think it needs a female to female db9 serial cable, all I have is a DB9 serial to rj45 console cable for the 2801 router, also I cant find the IP address of the sf300 switch, it is directly connected to the 2801 router, I issued a show arp to the router but didnt find the switch's IP add for web access, to sum it up I have no way of configuring the switch, is there any way to find the IP address of the switch? It also dosnt show on show cdp neighbors?
View 13 Replies View RelatedI want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View RelatedI can backup the router settings on an RV110W, but not restore them. I get an "unable to write" error. (probably not the exact verbiage). Defective router, or firmware issue?
View 14 Replies View Relatedhow to connect two subnets with two switches and one router using router sim software?
View 1 Replies View RelatedI have the port numbers but do not know how to proceed from there. Router is a WRT160N V2.
View 9 Replies View RelatedI have the N600DB Wireless Router I am connected to the internet, but cannot open My Routers Homepage with http://router or http://192.168.2.1. How can I get to this page to reset the router settings? I also cannot connect any of my wireless devices to the network..
View 1 Replies View RelatedI installed the Cisco LMS 4.0.1 (test mode), and monitoring services of the switches (data collection and information system) are working.
But when I need to apply some configuration via CiscoView settings are not applied.
The following message is displayed when I try to apply some configuration on an interface of any one switch.
"Message Timeout on 172.20.1.10. This error could be due to lack of access to the host, invalid SNMP credentials, or a busy device. To correct the problem, do one of the following:
- Verify access to the host.
- Check the SNMP credentials.
- Increase the timeout value through the preference options on the chassis view."
I've checked the credentials and SNMP communities, the problem continues.
I want to setup BB to monitor snmptraps with failure. The BB log shows can't connect to all switch ports 161, and I even can't telnet to XXX_17f 161 for example. My switches are Cisco C3550, C2950, ASA etc.
Mon Nov 7 15:43:03 2011 bbnet Can't connect to server XXX_17f on port 161
Mon Nov 7 15:43:03 2011 bbnet Can't connect to server XXX_9f on port 161
Mon Nov 7 15:43:03 2011 bbnet Can't connect to server XXX on port 161
We need to "reset" a SG200-08P switch back to the factory default settings and noted the "Quick Start Guide" implies the "Reset" button next to the power button doesn't exist and refers the user to the "Cisco Small Business Smart Switch Administration Guide" for instructions. We couldn't find any information related to a "factory reset" in that document either. Pressed the "paper clip button" on the switch but we still can't get in.
View 7 Replies View RelatedI get a empty blue window when I try to open "port to VLAN"
We have upgraded the software but it doesn't work.
I have posted on other sites as well everyone says to use Qos but they dont tell me how.I would just like to be able to limit my brothers bandwidth not just programs. We both use laptops, I use Ethernet, he uses wifi. My router does not have a wifi speed setting. I have tried multiple times to try and set up Qos on my own but it has not worked at all
View 1 Replies View RelatedNo ports seem to open up when they are supposed to be open according to the routers GUI.When i use "port checker"-websites, they even say that port 80 is closed until i actively open it in the router, then it shows up as open. This however only applies to port 80, no other ports shows as open OR allow any traffic through.The same thing happens when the router is in DMZ.What I have done so far is google my butt off without any results, I have tried a new router, a new network card, formated, re-installed windows and made sure that my ISP is not blocking the ports that i have tried to open.My purpose of opening a port is to run a mumble server, which I have run on a Hamachi VPN so far, and that has worked fine.
View 10 Replies View Relatedi have a router connected to my ISP which can get me 2 different IP's at all times (the router gets one IP).Now i want to get my computer to have a different ip as my router has (seen from outside my home network) - i want my computer that accesses the internet through my router to have a different IP as my router. I know that if my computer gets it's IP from my router's subnet, then it will (seen from outside) always have the same IP as my router. So the question is how do i get around this ? Do i just have to change my PC's DNS / gateway settings to match my router's ? The PC is connected to my router via wifi. Or would forwarding some ports on my router work ?
View 3 Replies View Relatedi don't have the cd to set my wireless router back up, so how do I go back to factory setup without it?
View 2 Replies View RelatedOne of the laptops in my home connects to the wireless network provided by my brand new Belkin (N600 Dual Band) router with no difficulty at all - the other will not connect at all (it SAYS it is connected to the network, but it says that it is a 'Local Connection Only, and will not open any web browsers or allow you to get on to the internet) why is this happening and, more importantly.
View 1 Replies View RelatedI am replacing a Netgear wireless router (WGR614v10) with a Cisco WRVS4400N. When I go to set up the device on my Mac, 192.168.1.1 will not open in a browser. Do I have to do the setup on a PC?
View 2 Replies View RelatedI have a RV042 Dual Wan. Two internets balanced wow! who would've thought that the headaches were waiting patiently right down the corner.
I was working with a 2wire Gateway that came with my ISP. I was able to open the ports in order to have public access for my students and teachers to upload their work. All I had to do was to allow my server ip address to have access to different ports blocked by the ISP. I used [URL]
I bought the RV042 for various reasons like excellent content blocking, load balancing, quick vpn, among other. But I just can't open the port 80 while having having my two ISP connected with load balancing, not even while having only one modem connected.
I have resolved many issues using the protocol binding. I have tried everthing. I just don't undertand something.
Whenever I connect my server to my old router, "www.canyouseeme.org" tells me that my port 80 is open. Whenever I connect my servet to the RV042-DW, my port appears closed.
So it's not any OS issues.
I've tried:
- To forward the TCP 80~80 port to my server static ip address... but failed
- To enable UPnP function with the same port... but failed
- To configure the port triggering with the same port.. but failed.
- To disable the firewall.. but failed.
- To use transparent bridge in the WAN1 with my 2wire Gateway... but failed
- To set up an account in DNS.ORG already had one, everythings is in green.. but failed.
- To change the configuration in my old 2Wire Gateway router to allow a DMZ zone so all ports are public... but failed.
- To assign RV042 router ip address in my old 2Wire allowing that specific address to allow certain ports to be public... but failed.
I have the Firmware v4.0.4.02 from DEC/11
[URL]
I have been trying for about a week to get open nat on my three xbox 360's I have in my home. Things came to a head last week when the gaming group and I tried to play over xbox live, but our games kept disconnecting. When I checked my network, none of my xboxes had open nat.
I had only one public ip at the time we had the trouble, but now I have 5 public ip's from comcast. Currently, I only have one of them setup with my router working as normal.
On that router, I have given the two xboxes static ips:
10.141.167.50
10.141.167.51
One of the xboxes is setup with port forwarding with the following ports:
3074 UDP/TCP
88 TCP
80 TCP
53 UDP/TCP
the other xbox is setup as a dmz host. The xbox that is setup with port forwarding gets open nat, but the other one, despite being the dmz host, does not get open nat.
The router is setup as follows:
10.141.167.1 - router ip
10.141.167.2-149 - dhcp server range
255.255.255.0 - subnet mask
My dns servers are from open dns. I have only one wan connection coming into the router also. That is through comcast business class. The connection is a 30/5mbps connection. One last thing, I have the latest firmware on the router as well. I updated it last thursday evening 12/8/2011.