Cisco Switches :: Can't Open Port To VLAN Menu In SG200 -08
Jan 29, 2012I get a empty blue window when I try to open "port to VLAN"
We have upgraded the software but it doesn't work.
ADVERTISEMENT
Cisco Switches :: SG200-26 VLAN To SPA303 Not Working?
Apr 16, 2013We recently purchsed a SG200-26 and have several SPA303 with the 2 ports. The other component is a Sonicwall NSA3500.The SG200-26 is on an interface of the Sonicwall that interface has a primary of 172.20.3.x and the sub interface is 172.20.5.x. I labed the VLAN as 5?I went to the "Create VLAN" in the SG200-26 and also created VLAN 5 and under Voice VLAN the ID is 5.Then I went to the SmartPort and assigned GE24 as IP Phone + Desktop. That was OK. But when I go to the SPA303 and Enable VLAN and VLAN ID 5 I get Initializing Network. I am able to ping the 172.20.5.1 which is the gateway for the VLAN but still pull no IP. I also have an DHCP range assinged the subinterface.I also am using Cisco Configuration Assistant. I can see the switch SG200-26 and my IP set but it shows no IP. So I know that the CDP from the phone to the switch is working.
View 2 Replies View RelatedCisco Switches :: Does SG200 Support VLAN Trunking
Apr 15, 2013does SG200 support VLAN Trunking?
View 1 Replies View RelatedCisco Switches :: Unable To Get SG200-26 VLAN Configuration
Feb 20, 2013Below is my configuration so far.
GE1 General 1UP, 100T, 101T
GE26 General 1UP, 100U, 101U
But I could not get port GE1 on vlan 100 to ping to anything on GE26.It only works when i change it to 100UP... BUT the rest of the vlan ID (101) will still unable to work.
Yes. i need multiple vlan on a single port as I am running Virtual machines on the GE1 and GE26 is an uplink I need all vlan to communicate from GE1 to GE26. Is this possible?
Cisco Switches :: SV220W / SG200 - Proper Vlan Setup?
May 21, 2013i have a question about the proper method to setup up vlan(s) on a sg200 switch with a sv220w router. Should i setup the vlan on the router or the switch? I have small office setup, i need atleast 2 vlans to separate the networks. i want both to have internet access but be completely isolated from each other.
View 5 Replies View RelatedCisco Switches :: SG200-26 Switch VLAN And Internet Access
May 9, 2012I start writing this post telling you that I'm not a qualified network admin, so I beg your pardon if I do not use appropriate terms in my question. Also my english in not so good since I'm Italian and my english in almost scholastic.
This is the "story" :
I bought two switches as described above and actually I have to create 2 VLANS as described below :
VLAN id 2 name "Service_A" ports 1-4
VLAN id 3 name "Service_B" ports 7-9
all other ports can stay in default VLAN1.
my network infrastructure have some other very simple swtiches connected and 1 soho router (static ip 192.168.1.1) with dhcp active and ip pool address released from 192.168.1.100 to 200.
the SG200-26 have static ip 192.168.1.254 and 192.168.1.253
MY NEEDS:
I need VLAN for privacy matter so all computer connected to ports in VLAN2 cannot see nor enumerate PCs and resources on other VLANs, but I also absolutely NEED that all computer in every ports (and every VLAN even default VLAN1) can access the internet.
Cisco Switches :: Restricted Inter-VLAN Routing With SG200-26 And SG300-10
Feb 26, 2013My organization wishes to host a LAN gaming event. The setup I have in mind involves a 24-port switch for connecting all the player computers and having that switch connected to a smaller "core" switch which has the the game server and router connected to it. I'd like to know if I can set things up as follows...
SG200-26 with ports 1-24 on seperate VLANs so they cannot talk to eachother. I'd then like ports 25 and 26 to be an aggregated (for bandwidth and redundancy) trunk port to carry all 24 VLANs plus an additional management VLAN (ex. VLAN 100) that will be used for accessing the switch. I'd like those aggregated trunk ports to connect to an SG300-10 "core" switch which will be connected to the game server and to a router for internet access.
I'd like the ability to have two network connections from the game server to the switch, one on the management VLAN and one on a different VLAN (ex. VLAN 50) that will be accessed by the players (ports 1-24 on the SG200-26). The core switch needs the ability to perform restricted inter-VLAN routing, in that it doesn't allow VLANs 1-24 to talk to eachother but they can talk to the server's VLAN but only through specific service ports (ex. port 12345, 12346). Is this possible?
Furthermore how would I configure the SG300-10 to allow VLANs 1-24 to talk to VLAN 50, but not themselves or VLAN 100. As well, I'll probably have the router on it's own VLAN (ex. VLAN 60) and allow VLANs 1-24 to access it but only through HTTP port 80 for web access.
Cisco Switches :: SG200-50 VLAN For VoIP Phones Connected To SRP541W Router
Apr 15, 2013I am new to VLANs although I generally understand the concept. I have a small office with 25 desktop/laptops and 15 VoIP phones connected with a SG200-50 switch and on Port 1 I have the Cisco SRP541W router for DHCP and Internet access. My goal is simple: 1) Segregate the VoIP phones (voice) from the computers (data) and 2) Prioritize the VoIP phones traffic.
I believe this can be accomplished by setting up a second VLAN and maybe a third (if the default should not be used) and then identifying those ports as Voice VLAN ports. I guess I just need to know how to flag each interface and each port so that they all can talk to the router on Port 1 yet the voice and data will be in different broadcast domains. Also, do I need a management VLAN??
Is this setup correct? VLAN 1 - default (data) Port 1 (Trunk) (Tagged)Port 2 - 30 (Access) (Untagged)VLAN 2 - voice Port 1 (Trunk) (Tagged)Port 31 - 48 (Access) (Untagged) What should the interface settings be on each port (General, Access or Trunk)? What should the port VLAN membership be on each port (Tagged or Untagged)??
Cisco Switches :: Using SG200-50 LACP On Port 49 And 50?
Jan 23, 2012I used LACP on port 49 and 50.After upgrade firmware from 1.0.0.19 to 1.1.2.0 my LAG1 stay down...all port member stay down, port link is up but LAG stay down...I testtu delete and reconfigure LAG1 but nothing work...
View 3 Replies View RelatedCisco Switches :: From SG500 Port Appears Up But At SG200 It Is Disabled
Jan 4, 2013I have an SG-200-8 which connects to a stacked pair of SG500-28P switches. It is powered by PoE from the SG500. From the SG500 the port appears Up, but at the the SG200 it is disabled and nothing I do re-enables it. I know the cable is good because I had a previous netgear switch hanging off it and working, also the power gets through.I can only connect to the switch if I disable wifi and plugin a manually configured PC - DHCP doesn't get through to it from the SG500 end.I have tried a second SG200 same problem. Have disabled RSTP/ STP thinking it might to relate to the fact that a PC connected to the switch also had a wifi connection to the same LAN, but. Don't know where to go next. looks like a bug?
View 1 Replies View RelatedCisco Switches :: SG200 Apply The Smart Port Macro To Interface
May 23, 2012I´m a IOS CLI fanatic. Its the first tiem that I have to configure a SB switch. Its very confusing, I want setup a voice vlan id as 200. but I don see that this value change when I try to apply the smartport macro to the interface.Its possible change a smartport macro?
View 1 Replies View RelatedCisco :: LMS 3.2 Can't Open Menu Device
Feb 1, 2012LMS 3.2 can't open Manu Device Troubleshooting only begin I will check manu Device Troubleshooting but LMS 3.2 can't show detail about Device and show error on windows.I need fuction Device Troubleshooting becouse ATP customer.
View 1 Replies View RelatedCisco Switches :: SG200-08 And SG200-08P Fail To Hold Or Update Date / Time
May 24, 2011SG200-08 and SG200-08P fail to hold or update Date/Time.(New installation for a UC320 setup.)I've got both an SG200-08 and SG200-08P that are failing to maintain date/time when set with "Use Local Settings". Every restart/powercycle causes them to reset to Dec 31 1969. Other settings save fine.I first tried to set time via SNTP Unicast using a variety of public time server addresses including the 3 hard coded to the SG200-08 firmware:
Sadly though it always just shows "Active Server Server Host Address: 0.0.0.0" and continues having 12/31/1969 as the date. Both after a config save and a reboot.I can ping the NTP servers just fine from the switches either by IP or by hostname.At this point I've decided that I must be missing something simple. At least I hope so... otherwise it's a firmware bug which means waiting for a fix.Other devices behind the same firewall/gateway (RVS4000) are updating NTP
Cisco Switches :: SF300-24P / Configure Vlan 10 For Data And Vlan 20 For Voice On The Same Port?
May 12, 2011We are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies View RelatedCisco Switches :: SG200-18 To C2960S Trunked - SG200 Cut Off The Net
Apr 29, 2012how to connect our new SG200-18 to an existing Cisco network, in particular a C2960S.Here's what I've got:
<----- Rest of network ------- C2960S ----------- SG200 ----- (PC connected directly to the SG200)
On the C2960S-side here's what I've got on the corresponding interface:
interface GigabitEthernet1/0/1
switchport mode trunk
On the SG200-side I've set the IP-address and default-gateway accordingly, however:From the SG200 I can't ping any other host on the same IP-subnet as the switchFrom the SG200 can't ping the default-gatewaycan't ping from any other host or the default-gateway *to* the switch But:On the SG200 I've got plenty of MAC-addresses under "Dynamic Address Table" - however only MAC-addresses that belong to the management-VLAN of the SG200 (i.e. VLAN9 in my case)The MAC-address table on the SG200 even includes the MAC-addresses of hosts on the same VLAN I tried to ping without success. For example: I tried a PING from a host having a MAC-address of 00:19:bb:31:91:30. This MAC shows up in the arp table of the SG200. To cross check I connected a dedicated PC to the SG200 and assign it an IP-address out of the management-LAN-range of the SG200 - in this case I can access the switch (i.e. PING, WEB etc.)So to summarize: Connectivity is OK when going from directly connected devices to the SG200. No connectivity from devices that are behind the C2960S towards the SG200 and vice versa. (The problem is definitely not with the C2960S-side since we've got plenty of them hooked together without problems.) I'm enclosing the screenshots of the corresponding definitions on the SG200.
Cisco Switches :: Very Slow Transfers Between SG200-18 And SG200-8?
Apr 16, 2013I'm baffled by the poor performance that I'm seeing when passing traffic between my two Cisco SG switches.
The configuration is as basic as I can make it, no VLANs, QoS or bonding. Both have been updated to current firmware as part of the troubleshooting process.
When I transfer data within one of my switches I see 50/60Mb/s. When I pass the same traffic between both switches I see 0.6 Mbs/ or less.
I have tried to eliminate every possible factor including switching out the cables. No success.
Cisco :: How To Open Port 161 On Switches And ASA For BB Monitoring
Nov 7, 2011I want to setup BB to monitor snmptraps with failure. The BB log shows can't connect to all switch ports 161, and I even can't telnet to XXX_17f 161 for example. My switches are Cisco C3550, C2950, ASA etc.
Mon Nov 7 15:43:03 2011 bbnet Can't connect to server XXX_17f on port 161
Mon Nov 7 15:43:03 2011 bbnet Can't connect to server XXX_9f on port 161
Mon Nov 7 15:43:03 2011 bbnet Can't connect to server XXX on port 161
Routers / Switches :: Why Is Port Forwarding Not Open
Dec 25, 2011When checking my port forwarding, it says that it is not open.
View 2 Replies View RelatedRouters / Switches :: Unable To Find Open Port
Feb 7, 2011I have just upgraded my AIM and Skype messengers and now it won't let me sign in. I did before with my old versions. It is saying that my internet connection is bad which it is not. I have looked up ports in my Yahoo messengers, Control Panel and Bit Torrent still nothing.
View 6 Replies View RelatedRouters / Switches :: Open A Port On A Motorola Modem?
Aug 26, 2011how do i open a port on Motorola modem
View 1 Replies View RelatedRouters / Switches :: When Checking Port Forwarding - It Says Not Open
May 23, 2012When checking my port forwarding, it says that it is not open. Why?
View 6 Replies View RelatedCisco Switches :: VLAN Port Membership Via SNMP On SG300-28
Sep 4, 2011Any snmpset commands to modify port vlan membership on SG300-28 switches? I checked [URL] however this information is apparently only valid for catalysts.
The latest firmware is installed and the provided MIB files are used.
Cisco Switches :: SG200-18 Switches With LC Single Mode Fiber SFP's
Dec 2, 2012We have a project in which we are using 34 Cisco SG200-18's each with a MGBLX1 (LC Single Mode Fiber) SFP mini-GBIC.All the fiber's come back to one building where we must "bridge" all 34 fiber connections. What hardware should be used to accomplish this? A L2 switch? For example, a 12 port SFP Switch with Fiber SFP's accepting the first 12 fiber connections, then other switch with SFP for the next 12 and so on, until there is a overall capacity of 36 and having patch cables between the 3 switches?
what cisco or non cisco hardware would work with these SF200-18's to accomplish this?
Cisco Switches :: Replacing Some Netgear Switches With SG200
May 16, 2012We are replacing some netgear switches with the Cisco SG200. The situation is relatively straightforward. We have a series of VLAN's coming in on a trunk from a service provider for our Metro Ethernet locations. These trunks then get cross-connect to various location for connectivity. The problem we have is there are two VLAN's that need to go to the same switch which provides access to our public IP block.
I set up the two VLAN's on the SG200 with the trunk port VLAN tagging on the service provider port. Then I set up a separate port for untagging the traffic with the PVID of the respective VLANS's as follows: [code] The public switch has no VLAN's configured (it is an SG200 too). If I connect GE2 to the public switch everything works fine. When I connect GE3 to the public switch, things die. I thought this might be caused by STP although STP should not be detecting issues like this across separate VLAN's. Disabled STP, no change.The same configuration with the Netgear worked without an issue. FYI, the VLAN's cannot be changed...they are defined by the service provider in this particular case. otherwise we'd just make them the same..
Cisco Switches :: ASA5505 - Does IOS Like CLI Exist In SG200 Switches
Aug 28, 2011I need to purchase a few Gigabit PoE switches for a small business and I am thinking that SG200 or SG300 switches are perfect for this purpose.
Layer 3 functionality in SG300 switches is not great - HSRP or any other next-hop redundancy protocol is not supported, dynamic routing protocols are not supported, policy-based routing is not supported, etc. I may get one SG300 switch for inter-VLAN routing so that I do not have to send traffic to a Layer 3 device for this purpose, especially because my Layer 3 device (ASA5505) has only 10/100 Mbps interfaces. All other switches in the network don't have to be Layer 3 switches, and I am thinking of perhaps getting SG200 instead of SG300 swithces. However, because I am a long-time Cisco engineer, and know ins and outs of the IOS CLI, I would much rather administer the switches with CLI rather than GUI. So, do SG200 switches provide CLI (even if it is not officially supported) or is the only Small Business switch platform that supports CLI SG300? I do realize that the OS running on these switches is not IOS, but after having reviewed the CLI manual for SG300, I would say that 90+% of commands are identical to IOS CLI commands.
Cisco Switches :: SGE2010p VLAN Trunks Spanning Tree And A Port Blocked
Jul 21, 2012We are upgrading out internal office network. I have setup 4 switches and 1 router using the following config.
-2 SGE2010p's are stacked together forming vlan 30 (to be used for phones)
-2 SGE2010's stacked for workstation's under vlan 20
Both switches are apart of vlan 1 (the default)Ports 1 on each stack are connected to a Cisco 890 (port fe2 and fe3) in trunk mode. Ports 2 and 3 are in an LAG group and connected to the neighboring stack (I have attached a diagram), and are also in trunk mode).At this point one port (port 1 on either stack) goes into blocking mode, and I get why ,it's a physical loop.I need more than a 100mb link between switches (which is what pulling the LAG between switches gets me), but I don't want to route phone traffic through my workstation switches to get out of the LAN.Is it possible using these switches and router to have a LAG between stacks and a link to the router for traffic to 0.0.0.0 ?
Cisco Switches :: CLI Access To SG200 Switches?
Dec 27, 2012I just picked up a pair of 18-port SG200s, and I'm trying to figure out of there's some secret trick to getting CLI access to them? I've upgraded to the latest version of firmware (1.2.7.76) hoping that may work, but no luck.I can tell the guts to support a CLI are there, because writing the config out to a TFTP server shows identical an identical config style to the SG500 I have here.Is there some way to enable it?
View 5 Replies View RelatedCisco Switches :: SG200 Vlans Across Two Switches
May 22, 2011I am trying to set up three vlans across two switches. The switches are Cisco SG200 and SG 300 series. There are 20 devices connected to the two switches including a router for Internet. Among these devices are five wireless access points all hardwired to the LAN. If I understand correctly the first thing I have to do is aggregate the two switches. I ran two cat5 cables to ports 1 and 2 of each switch. As I understand it all I need to do is to create SAG with the two ports on each switch. I think I need to use tagging but I don't really understand how to do this. Once I get the trunking set up correctly I want to create one vlan to which all devices will belong for Internet access. The other two would be for data and VoIP. Do I create vlans with the same name on both switches? When I assign the devices (by port) do I need to enable tagging? Which type of port setting should I use? I am assuming that by including the acess points in the vlans will mean that any wireless device connected to them will have acess to the Internet and the devices in the same vlan.
View 1 Replies View RelatedCisco Routers :: Router On A Stick VLAN With SRP547w And SG200
Aug 14, 2012As per the title, I just require 3 to 4 VLANS with inter-VLAN communication enabled.
In the past I have used this router with each port of the internal switch set to a different VLAN, with each in turn hooked up to an unmanaged switch. This has work fine for me but I want to dip my toe in the world of .1q VLANS and gain some added flexibility and neatness.
Cisco Switching/Routing :: SG200 / 3550 - Creating VLAN And Isolating PC On Network
Feb 12, 2013I was given a task of creating a vlan and isolating one pc to access an internal website (192.168.90.15) on a specific port (port 8080)The pc is connected in the following manner:
PC--> HP Switch --> Cisco Small Business SG200 switch --> 3550 Catalyst 1, 3550 Catalyst 2 and 3550 Catalyst 3.
I have created a vlan 110 on the Main 3550 Catalyst switch and successfully added the pc to that vlan.However, that PC must be able to access the internet and an internal website on port 8080.I have placed an access-list on the main 3550 catalyst switch which is connected to our router as below:
Client ip address: 192.168.100.2
VLAN 110: 192.168.100.3
access-list 110 permit tcp host 192.168.100.2 host 192.168.90.15 eq 8080access-list 110 permit icmp host 192.168.100.2 anyaccess-list 110 deny ip 192.168.100.0 0.0.0.255 ? I was unable to access the webserver even after many attempts.
Cisco Switching/Routing :: SG200 / WAP4410N - Multiple VLANs Without VLAN Aware Device
Feb 12, 2012I have a Cisco SG200 26 Port Switch, 2 Cisco WAP4410N Access points, and a VLAN aware Router. I have created 4 VLAN's. For the sake of this conversation lets call them.
98 - Intel Vpro
99 - Management
100 - General
101 - Guest
The Access points are capable of doing V LAN tagging so I plan on having them tag a guest network as V LAN 101. That can get sent to the V LAN aware router and out. No problem. I have some devices, or management pages that I don't want accessible from the general network. (Intel V pro KVM, Remote Management Cards, AP Config Menus, Switch config menu...) . I need to be able to take a V LAN unaware device, plug it into port 1, and have it communicate with V LAN 98, 99 and 100.
Cisco Switches :: Is There CLI In SG200 After New Firmware (1.1.2.0)
Dec 15, 2011With the new firmware (1.1.2.0) released for SG200 switches, is there CLI now?
View 4 Replies View RelatedCisco Switches :: Disable STP On SG200?
May 22, 2013I am trying to connect an SG200 to a customer's existing network. The customer does not want to receive any bpdu frames from the SG200. The customer's port has bpdu guard configured to err-disable their port upon receipt of a bpdu.
How do I completely disable spanning tree on the SG200 so that it does not send any bpdus?