I have the N600DB Wireless Router I am connected to the internet, but cannot open My Routers Homepage with http://router or http://192.168.2.1. How can I get to this page to reset the router settings? I also cannot connect any of my wireless devices to the network..
View 1 RepliesNew N600 DB router, has one usb connection. Can I use a usb hub to connect both a printer and a hard drive?
View 2 Replies View RelatedI have an Belkin N600DB F9J1102 modem router but it doesn't have a PARENTAL CONTROL in the Utilities section as mention in the manual.
View 1 Replies View RelatedI purchased the Belkin N600DB, but I can't seem to find a way to reserve IP addresses for my connected devices. I need to run a server through the router, but (naturally) it keeps changing my local IP address. I cannot find the reservation utility.
View 1 Replies View RelatedIn my new laptop with os windows 8 my 5Hz network is not visable.My 2.4Ghz network is the only one that is showing.
My Router is a Belkin N600DB
Hardware F9K1102 v1
Firmwareversie 1.00.19 (Jul 6 2012)
Versie opstartprocedure v0.07
Can I set up n600 db F9K1102v1 as wifi range extender with no rj45 cable?
Dont have cable infrastructure in section of building where i need net access.
Have a Cable/Modem (wireless) as main router and need to extend the signal using the N600DB - but without cat5 cable between modem/router & N600.
I'm trying to get 'Access Control' working so I can limit Wi-Fi time on my kids iPod touches, but the settings aren't clear and the help file is not clear whatsoever.I've been testing it with my iPhone, I have the MAC added, but none of the options available will even stop my iPhone accessing the internet over my Wi-Fi.
View 1 Replies View RelatedN600DB - Currently configured with primary computer hardwired to router, 1 laptop via WiFi, a Network booster used by iPhone/iPads and every time I wake the primary computer I get the Router Monitor alert that my internet connection has failed. By the way, I am currently using the primary computer to post this and the Belkin Router Monitor still says my "internet connection has failed" and An Internet connection cannot be established at this time. Re-booting your router may solve this problem, but you will temporarily lose your connection during the reboot.
View 1 Replies View RelatedAm running firmware ver 1.00.19. Set up DDNS with DynDns.Org and all is well. Set up virtual server with DDNS info. Trying to connect to an IPcam (Foscam 8905W). IPcam is set up with static IP with ip outside Belkins DHCP range.
Problem: When trying to access the IPcam through the internet (DynDns) Belkin takes me right to the Belkin router Setup screen, not to the virtual server settings (IPcam). I was able to do it a couple of months ago,but not now. I may have upgraded my firmware in that time from 1.00.12.
I have a 1TB hard drive connected to my N600DB that I use as a media server to my kids Xbox... My problem is that I use this drive to back up all my data from my laptop, including movies, pictures and music. I only want to share the movies... I have over 5000 pictures alone so my router never gets to index all the movies I want to share..
P.S. I have the F9K1102 v1 with Firmware 1.00.19
I have a N600DB configured as a primary router. I got another playmax n600HD router which I want to configure as an access point that extends my network upstairs and allows me to attach some wired devices like my ps3. I followed the basic principles of setting as access point and my locally connected ps3 and NAS are communicating but no Internet access. How the 2nd router can connect to the internet?
View 2 Replies View RelatedOne of the laptops in my home connects to the wireless network provided by my brand new Belkin (N600 Dual Band) router with no difficulty at all - the other will not connect at all (it SAYS it is connected to the network, but it says that it is a 'Local Connection Only, and will not open any web browsers or allow you to get on to the internet) why is this happening and, more importantly.
View 1 Replies View Relatedtrying to download current firmware for my f5d8233-4v4 and i get this message, "No known program will open this file. This file is part of a program."
View 1 Replies View RelatedWindows cannot open this file (the update). what program opens the update? I just bought a SURF N300 v F7D6301 and am trying to install the update on the website, but I just get a box that says windows cannot open this file.. what program do i need to tell it to use to open the update?
View 1 Replies View RelatedF5D8233-4 using wide open west, losing internet for a few seconds during use, wow says it's firmware but the router says it's up to date.
View 3 Replies View RelatedHow to change my NAT type from moderate to open for xbox 360. Belkin n450 dual band
View 1 Replies View RelatedThe Lg840g is a tracfone with wifi capability. I get strong wifi signal and connection at home, but receive failure to connect to requested host message when I open the browser. This phone works at wayport wifi, so I assume it's a compatibility problem with the router. Is there a fix? (Router works great with our Acer and Kindle tablets though.)
View 1 Replies View RelatedI assigned the access point a static IP 192.168.2.50 within the router IP range. My computer wireless card is detecting the access point but I can't get the belkin n600db to detect the access point.
View 12 Replies View RelatedIf your wireless indicator is flashing red when you discover the smurf, it can mean that someone has tried to logon with an incorrect password. this is not necessarily an attack, it could be someone you have allowed access too, who has forgotten the password? In this case entering the correct password will solve the problem.However putting your own MAC address into the filter will simply block your own machine.
View 6 Replies View RelatedI have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
View 1 Replies View Related(F5D9230-4 v5111 Belkin mimo router ) is version 5.02.08 the most up to date firmware for my router?
View 1 Replies View RelatedHow do I setup my Belkin F7D1301 with a 16 port 10/100 switch so I can use the wireless on the Belkin and have the 16 port switch for my hard wires?
View 1 Replies View RelatedNo ports seem to open up when they are supposed to be open according to the routers GUI.When i use "port checker"-websites, they even say that port 80 is closed until i actively open it in the router, then it shows up as open. This however only applies to port 80, no other ports shows as open OR allow any traffic through.The same thing happens when the router is in DMZ.What I have done so far is google my butt off without any results, I have tried a new router, a new network card, formated, re-installed windows and made sure that my ISP is not blocking the ports that i have tried to open.My purpose of opening a port is to run a mumble server, which I have run on a Hamachi VPN so far, and that has worked fine.
View 10 Replies View RelatedHow do FPS's open UDP ports without needing to configure the router to forward them?I never have to forward ports from my router to my PC. Every game i have somehow manages to open the UDP ports it needs without me having to configure my router. Yet when i check to see if those ports are open (prior to starting the programs) they always come back as blocked or closed. Now I'm currently working on a UDP Internet program and need to know how to do the same thing - open ports on a router without having to make the customer configure their routers. I'm THINKING that other programs start with a TCP/IP connection on the desired port and that opens the UDP port. Is this the answer or is there another method used?
View 5 Replies View Relatedto access VOD database i must open three ports on the router - not sure how to
View 3 Replies View RelatedI cannot open router settings... I had recently opened some ports on my router. However today I tried to access the settings and all it does is a web search for the gateway (192.168.1.254). The internet is working. I reset the router and it did not work. I cannot do a hard reset because I will lose all my settings for my company's settings. Also the router is a Netopia modem/router
View 2 Replies View RelatedWhen checking my port forwarding, it says that it is not open.
View 2 Replies View RelatedI am replacing a Netgear wireless router (WGR614v10) with a Cisco WRVS4400N. When I go to set up the device on my Mac, 192.168.1.1 will not open in a browser. Do I have to do the setup on a PC?
View 2 Replies View RelatedI have a RV042 Dual Wan. Two internets balanced wow! who would've thought that the headaches were waiting patiently right down the corner.
I was working with a 2wire Gateway that came with my ISP. I was able to open the ports in order to have public access for my students and teachers to upload their work. All I had to do was to allow my server ip address to have access to different ports blocked by the ISP. I used [URL]
I bought the RV042 for various reasons like excellent content blocking, load balancing, quick vpn, among other. But I just can't open the port 80 while having having my two ISP connected with load balancing, not even while having only one modem connected.
I have resolved many issues using the protocol binding. I have tried everthing. I just don't undertand something.
Whenever I connect my server to my old router, "www.canyouseeme.org" tells me that my port 80 is open. Whenever I connect my servet to the RV042-DW, my port appears closed.
So it's not any OS issues.
I've tried:
- To forward the TCP 80~80 port to my server static ip address... but failed
- To enable UPnP function with the same port... but failed
- To configure the port triggering with the same port.. but failed.
- To disable the firewall.. but failed.
- To use transparent bridge in the WAN1 with my 2wire Gateway... but failed
- To set up an account in DNS.ORG already had one, everythings is in green.. but failed.
- To change the configuration in my old 2Wire Gateway router to allow a DMZ zone so all ports are public... but failed.
- To assign RV042 router ip address in my old 2Wire allowing that specific address to allow certain ports to be public... but failed.
I have the Firmware v4.0.4.02 from DEC/11
[URL]
I have been trying for about a week to get open nat on my three xbox 360's I have in my home. Things came to a head last week when the gaming group and I tried to play over xbox live, but our games kept disconnecting. When I checked my network, none of my xboxes had open nat.
I had only one public ip at the time we had the trouble, but now I have 5 public ip's from comcast. Currently, I only have one of them setup with my router working as normal.
On that router, I have given the two xboxes static ips:
10.141.167.50
10.141.167.51
One of the xboxes is setup with port forwarding with the following ports:
3074 UDP/TCP
88 TCP
80 TCP
53 UDP/TCP
the other xbox is setup as a dmz host. The xbox that is setup with port forwarding gets open nat, but the other one, despite being the dmz host, does not get open nat.
The router is setup as follows:
10.141.167.1 - router ip
10.141.167.2-149 - dhcp server range
255.255.255.0 - subnet mask
My dns servers are from open dns. I have only one wan connection coming into the router also. That is through comcast business class. The connection is a 30/5mbps connection. One last thing, I have the latest firmware on the router as well. I updated it last thursday evening 12/8/2011.
I'm using a WRVS4400N and have all the proper ports open as well as the corresponding ones in the windows firewall. I've tested this with multiple port checkers online, such as grc.com. I've even go so far as to put one computer on a dmz and turn off the firewall on others. I've tested multiple ports on different computers. As well as from different remote gateways (other people's computers) just to see if it was a loopback problem.
I have the latest firmware installed and have done this from a clean install as well. This problem won't go away. My addy is nbcr [dot] dyndns.info if you'd like to have a test yourself and see that 118 is indeed closed.
I have an extensive computer repair background and run my own shop repairing computers, however networking is my weak area. Oh and its version 2.
I just bought and setup a RV110W. I noticed while scanning it from the WAN side that it always has port 443 open, even when remote management and VPN access are disabled. Why is this port still open, and how do I close it? Or is this a bug in the firmware? I am using firmware version 1.1.0.9, which is the most up-to-date for this unit. Having open ports allowing unsolicited contact from the WAN side, especially inadvertant ones, is a major security hole.
View 7 Replies View Relatedhow to open the tp-link interface setup for my TD-W896ON? i have a user and a password but where do i add them ??
View 1 Replies View Related