D-Link DIR 655 :: Blocking Website Of Admin
Apr 5, 2011
I have a dir-655 a3 router that is blocking my website ip address.I could previously access this site until one day, without changing any router settings, it started blocking communication to my website. pings, tracerts, web browsers, everything simply times out. It resolves the IP address ok but doesn't go any further than that. I was on firmware 1.31 and have now upgraded to 1.35NA, but no luck. I have also tried resetting factory defaults to no avail. If i bypass the router and plug my computer straight into the modem, the site loads fine. so its definitely the router. I have tried this on a number of devices to make sure. It appears that for some reason the router is blocking that specific IP address as it is on a shared hosting and I can't access any other sites on the same IP address. Does the router check the IP address with any web service before returning the request?
View 4 Replies
ADVERTISEMENT
Apr 20, 2013
For the last week, I haven't been able to access my banking web site (Royal Bank in Canada). It doesn't matter which browser (FireFox, IE, Chrome) or computer (desktop, laptop) or even my cell (on WiFi).It must be the router (DIR-825, HW-B1, FW-2.07NA) since I can connect to the web site fine if I connect straight to the modem. (Also, if I turn off WiFi on my cell, I can connect to their web site but once I turn WiFi back on, it wont connect).I tried restoring to factory settings but that didn't work.I tried some of the suggestions here: http:[url].....
- Turn off ALL QoS or Disable Traffic Shaping. Advanced/QoS.
- Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.
- Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking
- Ensure devices are set to auto obtain an IP address.
- Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
- Enable uPnP and Multi-cast Streaming under Advanced/Networking.
View 3 Replies
View Related
May 16, 2013
In Setup > Parental Control it is possible to set rules attached to specific website URLs. I want to block access from 1am to 6am.
However these rules only apply to websites URL. Is there a way to apply a rule to ALL websites at once? I tried to enter "*" or "*.*" in website URL field but it doesn't work.
View 1 Replies
View Related
Feb 27, 2011
l have a web-site and when l go on it it comes up with blank page internet explorer cant load this page.l have phone talk talk and they cant fix it.l have a d-link router,its only my own web-site l cant access all other web-sites l can access.
View 2 Replies
View Related
Jan 24, 2011
How do u lock your wirless router connection so other people. Can't get on it
View 2 Replies
View Related
Jun 23, 2012
I'm using a WRT160N v3 wireless router and it is somehow blocking my website. It works when connected directly to modem.
View 1 Replies
View Related
Jul 29, 2011
is there a way i can block a website from being viewed.i would like to do this from the setup page of my e1000 under website restrictions.
View 1 Replies
View Related
Feb 18, 2011
WAG320 allows website blocking, to enable this you can use a keyword. I would like to use this function to block anoying advert sites (in the same way I could with my Netgear DG834GT) - However the way this function has been implemented is less than ideal.
e.g. when a site is blocked by the router, the router does not return a response - this is great until that site forms only part of a web page that is permitted. What then happens is the web page takes forever to load as the responses have to timeout for the blocked components.
The way this function *should* have been implemented, is the router should return a blank response for each of the blocked sites. Netgear do this and it works a treat, they even put up a banner saying "Website blocked by Netgear".
This is such a simple feature, why has Cisco overlooked this and how do I go about raising a product enhancement ? I've been through the helpdesk which quite frankly is a farse, they asked me to reflash my firmware which surprisingly didn't resolve the issue - they then told me to send them the unit back because it must have a fault !?!? (and I have to pay for postage of course!) I explained the issue about 5 times, but the operator on the other end was just a script reader and I could not speak to an engineer - very poor.
View 2 Replies
View Related
Mar 19, 2012
I have a Linksys E2500 wireless router. It seems to be blocking a website (evernote.com). I cannot access this site from any of the computers/ devices in our house, whether they be connected by ethernet or wireless. However, when i move to a different network, I can connect to this site immediately from exactly the devices that do not connect in our house.
How can I determine how/if the router is somehow blocking this site? I have reset the router and upgraded the firmware. Same problem persists. I see nothing in the router settings that would be blocking this site, and I have certainly done nothing intentional in the settings to block this. We used to be able to connect to this with no problems, but all of a sudden, we are blocked.
View 5 Replies
View Related
Mar 8, 2013
I would like to set up a monitoring/site blocking system where I work (owners request) to black sites like Facebook, YouTube, etc. Are there any decent, basic freeware ones out there?
View 1 Replies
View Related
Aug 4, 2011
I am tying to block a certain website on my WRT54GL Linksys router.I have put in MAC adresses on the Access Restrictions tab but its still not working.
View 3 Replies
View Related
Sep 12, 2009
Setting up website blocking. I have set up access restrictions for selected times and days but I also want to set up access restrictions for webistes. Perhaps I'm just not clear on how this is supposed to work - I created a policy called 'Site' and then enter the URL in the website blocking area. The options under the 'Access Restrictions' area are either 'Allow' or 'Deny' - intuitively one would assume the selection should be 'Deny' since this policy is to block access to specific URL's. However, if I click 'Deny' and then save, then the URL's I just entered are cleared. However, if I select 'Allow' then I am essentially giving 24hour access every day to my computers (but blocking the URLs), which then seems to go against the access restrictions I set up for selected times and days. Perhaps these two policies are mutually exclusive but it does not seem clear that it is.
View 2 Replies
View Related
Jun 14, 2010
I've been given the task of blocking access to certain websites, facebook, youtube, etc The router is the Cisco Linksys WRT120N
Ive entered the web addresses in the Website Blocking by URL Address boxes on the internet access policy page but it doesnt seem to work no matter how i do it.
Ive tried to deny internet access but that shuts of all internet access.
View 9 Replies
View Related
Sep 30, 2011
I have an RV110W running firmware version 1.0.1.6 and I am trying to figure out how to enable website blocking in the Internet Access Policy screen. The Add Row button is grayed out in that section, as are the associated checkboxes.
Is there something else one needs to do to enable this feature?
If I set a name etc. at the top, and click save, it tells me "You must at least set a website blocking or PCs rule," so it is not the case that one has to save some information before continuing!
View 10 Replies
View Related
Aug 14, 2011
There is a way to block access to a website by password protecting it through my linksys router, which is one of thoe wrt54gs. I know I can completely block access of a website and can restrict the viewing hours of facebook at certain times through the router admin IP site but was wondering if it was possible to make it so you have to use a password to view said certain site. If there isn't is there any way maybe through a program or do I have to go through my ISP to see if they can do what I am asking for.
View 1 Replies
View Related
Jan 30, 2012
I have 1.00 build 0522 and searching the support website I see no link. But reading here I see there is a later version.
View 1 Replies
View Related
Oct 30, 2011
I followed this simple procedure to turn my DIR-655 into an access point: url...and it all worked except when I go to url... (which is where I left the router's IP address set) I don't get the DIR-655's admin login GUI, just a timeout. Since my main Linksys router is on 192.168.1.1, and my cable modem is at 192.168.100.1, and the DHCP addresses handed out by the Linksys router is from 192.168.1.100 to 192.168.1.149, getting to 192.168.0.1 should not be a problem. Functionally, the DIR-655 makes a great access point, wired and wireless are working very well, and I don't see any reason why I can't get to the web GUI admin page.I should be able to get to the DIR-655 router via the WAN port, as suggested in the procedure above, but I'd really really like to be able to get to it without having to connect a cable to the DIR-655 WAN port.
View 5 Replies
View Related
Dec 12, 2012
I have a DLink N300 (DIR 615), firmware 9.02NA.I've been trying to log into the "admin" but was only able to once. When I did get it everything was greyed out so I couldn't make any changes.
View 1 Replies
View Related
Jan 6, 2013
i'm having some trouble logging in as admin. I leave the password section blank as directed but it comes up as "incorrect password". I then tried the same using the "User" and it worked just fine but i cant change any of my settings.
View 6 Replies
View Related
Jan 28, 2012
I just bought the Dir-655 with 2.00 firmware. I am having trouble with my NAT on my game system and I have tried everything but I have everything setup on my router where it needs to be. I read somewhere, where a guy was having my same trouble and he upgraded his firmware to 2.03na. I have tried with no success whatsoever.
Downloading the file from the d-link website with no problems. But i keep getting the same message when i try to upgrade the router saying the file may be corrupt, the router is to busy, or I am not logged in as an Admin. I am the only one using the internet and I am logged into my router as the admin. it wont even start uploading the firmware to my router..
View 9 Replies
View Related
Feb 19, 2013
I'm plug with my laptop on the DLINK, no internet connexion available, and it's impossible to connect to 192.168.0.1 ..What am i suppose to do, i need to configure a static ip and specifics dns to get to the internet, and it seems that without internet i can't acces to 192.168.0.1 ...
View 1 Replies
View Related
Apr 13, 2012
Router is a DIR-601 hardware B with firmware 2.00NA Using the router connected to a cable modem, I was unable to gain admin access via WAN.To troubleshoot the problem, I connected the router to the LAN side of my main router (DHCP server, DNS, etc.) The primary router correctly assigns a WAN IP to the 601. The 601 operates normally to access the Internet either via its WiFi or via Ethernet. The 601 is configured for a different IP address range on its LAN side so there is no IP address conflict possible with my main router.On Tools->Administration, Enable Remote Management is checked, Remote Admin port is 1080 (I've tried others), and Remote Admin Inbound Filter is set to Allow.In this case the WAN IP address of the router is 192.168.0.98. When I go to http://192.168.0.98:1080/ with a web browser from the WAN side, I get no response. From the same computer I can ping the router with "ping 192.168.0.98".I figure I have to be missing something here. It appears that this feature just is not there, but others must have this working. It seems like I've tried every possible combination of filters, port numbers, etc., but it just doesn't respond from the WAN side. (192.168.1.1 on port 80 works just fine from the LAN side.)
View 3 Replies
View Related
Mar 12, 2013
I wanted to update the F/w on my rev b dir 825, but unable to load the login console for admin, I haven't changed anything and the router was still on 2.07NA f/w
View 1 Replies
View Related
Jun 20, 2011
Bought a new DIR-655 Rev B a few weeks ago.It's web admin interface has failed in some way. The device is still passing all user traffic in both directions, but attempts to connect to the admin interface with my web browser, from both the wired inside and the WAN outside fail. I can telnet to the actual tcp port number that it's configured for and establish a connection, but I can't get any response from it. At this point I'm expecting the only way I'm going to clear the condition is to power cycle the device when I get home from work. It is to note I have the device configured for https for the admin interface. Perhaps that's the more 'advanced' feature that's newer and is exhibiting some kind of bug, I wonder. I'm running the latest firmware available from D-Link.
View 5 Replies
View Related
Jun 26, 2011
I needed to immediately set a schedule and block IPs, these pages are built into the router.It took forever for the pages to load it took 30 minutes to navigae 5 pages. Every time I try it.Router is good and signal is excellent but the admin router pages to configure are frustratingly slow.As a techie it is anoying, as a customer getting support by the hour spend more on a faster better quillity router were the work can be done in 1/20th of the time it takes on this router.I'd say I have a dud but once setup the router is a great performer if you do not need to admin the router further?
View 3 Replies
View Related
Dec 7, 2009
I am having issues with my freinds new DIR-825 Rev:B1 Firmware:2.02NA, The admin pages are intermittently slow to load and sometimes wont load until I power cycle the device. I am using IE8 on vista x64, and have the issue on all pc's on the network. Is there a work around for this?
View 7 Replies
View Related
Feb 26, 2013
I was trying to access the modem router as the admin but AT&T seems to have a pain in the butt security system from me making any changes. I wanted to forward some ports to setup my Synology DS212j Network Attached Storage (NAS). I connected my d-link router to the already setup modem router which I am now connected to. I have to run off to school but I was wondering, would I be able to forward the port off my d-link DIR-601 and be able to host my NAS server off that?
I don't have too much in-depth networking experience besides setting forwarding ports, setting static IPs, but I can't do that since I am not the admin for the AT&T router. I figure the password for the AT&T router is just defaulted to admin or blank but I haven't had time to fully test everything out.
View 4 Replies
View Related
Jun 9, 2011
I just installed a TP-Link router. Everything (almost) works: PC internet, laptops internet, email, etc. An application on my PC can't communicate through the router to the internet server now. I am sure it is a port/IP address issue. But I am unable to figure out a solution. I have already changed the IP (of the computer with Windows 7) to a static IP address. I guess now I need to get the port access done. I know the ports in question from calling the vendor. I just need to get the application through the router.
View 1 Replies
View Related
Jan 12, 2012
within ACS 5.3, I'd like to use 2 external authenticator for the same service, like vpn remote-access.For the authentication, I know I can create an identity chain, to query SecurID and then AD, in case of user not found in SecurID.For the authorization rules, I need to provider a wide vèn access for SecurID users and narrow vpn access for AD user.Are there some parameter to use in compound conditions for SecurID ?
View 1 Replies
View Related
Mar 19, 2011
I can however connect to internet ?
Tried Explorer & Firefox
View 1 Replies
View Related
Nov 30, 2011
I have a Netgear WNDR3300 Dual-Band and is setup to use both 2.4Ghz and 5Ghz to achieve 300 Mbps connection.
On the DAP-1522, I use IE (not Firefox or Chrome) for configuration as follow:
- IP address: STATIC
- Wireless config: using Wizard
- Wireless security: WPA2 / AES
- Mac Cloning: disabled
I tested this by connecting a Windows 7 desktop AND laptop via Ethernet cable and both laptop can obtain IP address dynamically, so my DAP-1522 is talking to the WNDR3300 (it has DHCP). Both Win 7 machines can also access the Internet.The problem is, I can NO LONGER access DAP-1522 admin screen, even by typing the static IP address assigned to it. The ONLY way I can re-access it is:
a). Reset DAP-1522
b). Shutdown the WNDR3300 wireless router, assign a static IP to the laptop, connect via cable to DAP-1522
View 3 Replies
View Related
May 16, 2010
Im having some problems changing my admin password on my DCS920
I know the default login is Login: admin / Password: "blank"
So I go into maintence, and there's an option to change the password.
it lists:
old password
newpassword
confirm
So I leave the old password blank and type in my new password in the following 2 spaces. I click apply and a window pops up asking me to enter username and password. I just enter admin and leave the password blank. I hit ok, and everything seems to update ok. So i log out, and try to log back in.
A window pops up asking me for my password. I type in admin for my username, and my new password, and it wont work
I type leaving the username blank, and type in new password... WONT WORK
I type admin, and new password again.. WONT WORK
I try password with first letter capital.. WONT WORK
I try password with ALL CAPS... WONT WORK..
Basically it wont let me log in as admin anymore. I figure I may have typed the password wrong the first time so I reset the camera and try the process again.. SAME PROBLEM.
Am I doing something wrong in changing my password ?
I dont wanna leave my default admin login as admin/"blank" , but when I try and change the password, it wont let me log in again as admin.
View 4 Replies
View Related
Apr 28, 2011
Is there a way to block specific computers on the LAN from specific web sites by the domain name? All I can see is that if I put, for example, www.facebook.com, it will be blocked from all computers on the LAN, whereas if I want to block only 192.168.1.3 for example, I have to use the IP address through the Access Control, which is much harder and ****e to some "work around" by the user.
View 3 Replies
View Related
