D-Link DCS-942L :: Searching Support Website Getting No Link

Jan 30, 2012

I have 1.00 build 0522 and searching the support website I see no link.  But reading here I see there is a later version.

View 1 Replies


ADVERTISEMENT

D-Link DCS-942L :: Black Box When Viewing From Remote Website

Jul 22, 2012

I ran the setup CD and can access my camera from inside my local network. When I try to access it from outside, I can access the camera fine but the video stream is black. I tried RTSP ports 554, 2080 and 5632 with no success (of course I port forwarded the dsl modem as well). My dsl modem is a westell 7500 and my ISP is frontier communications. I contacted their support tech and at first he ran me through the exact port forwarding sequence I had already done on the modem. He then went away for a while and came back to say that I need to upgrade to their fixed internet address service. I understand dynamic DNS and don't think this is an issue because I can contact the camera OK, I just don't get the video through (black screen). Another issue is that the camera is reporting PPPOE 'failed'. The support tech has given me two PPPOE user names and passwords but neither work. The support tech said that they do require PPPOE.

View 3 Replies View Related

D-Link DCS-942L :: 942L - Gaps In Continuous Recording

Mar 10, 2012

I have my 942L set up for continuous recording. When I look at the files, the camera will record between 20 and 55 seconds, end that file and start another. The next file then starts between a few seconds and as much as 40 seconds later leaving a gap in the video recoding. The file sizes are all different and the amount of record time is different for each file.

Also, about 80% of the time, the time increments a few seconds on a playback and then stops updating even though the video is longer.

View 4 Replies View Related

D-Link DCS-942L :: Can't Run 942L Without Power Cord

Aug 5, 2012

I just got the camera today, looks good, works good, at least so far.. BUT I was SURE this camera had a battery and charge function!? What's the point of having this camera if I can't place it say inside my car or in the garage (where it needs to be hidden, alas I can't use any cords!)?

View 5 Replies View Related

D-Link DCS-942L :: Does Not Work With MAC

Nov 10, 2012

The company has a glitch that they are not sure if they will fix so you can't record with mac.  I am unable to return my cameras to staples and Im out the money for the memory cards I opened.  It says you can record with MAC clearly on the box!!!!  Bad business practice for STAPLES and DLINK.

View 3 Replies View Related

D-Link DCS-942L :: Monitoring App For Blackberry?

Jul 9, 2012

iphone and android app but no blackberry.

View 3 Replies View Related

D-Link DCS-942L :: Cannot Get Camera To Work On PC

Jan 4, 2013

I just purchased 2 cameras and have one set up.
Firmware V 1.12

Works great on my android phone and connects fairly quick. When I try to see the camera image on my PC with windows 7 64 bit, I log into my d-link and it shows the camera name on left side of screen, then says Java run time environment not installed.I uninstalled java 5 times and re installed both 32 and 64 bit but keeps coming back as not installed. Camera is set up wirelessly through a Belkin router, so far no EZ config

View 8 Replies View Related

D-Link DCS-942L :: How To See Who Is Watching My Camera

Mar 27, 2013

Is there such a possibility in the firmware or through telnet?

View 3 Replies View Related

D-Link DCS-942L :: How To Manage Cam Using A Web Browser

Apr 13, 2012

As DCS-942L IP cam is compatible with "NVSCGI APIs" (search this string on a search engine and you will find some useful PDF docs), many features of this IP Cam may be enabled or disabled using any web browsers, for example we can manage the motion detect.

[url]....

View 3 Replies View Related

D-Link DCS-942L :: How To Switch Profiles

Dec 18, 2012

I just bought new 942L (HW Rev3, 1.12 FW) and the only profile which is used to stream to iPhone or Web browser in mydlink is profile 3 which is limited to JPEG. Is there some way how to change the profile to be used for streams or is there a way how to make to profile 3 something else then JPEG?

View 1 Replies View Related

D-link Dcs-942l :: Keeps Going Offline Wifi?

Apr 19, 2012

I have 3 DCS cameras on my network all setup WiFi

2 are DCS-932L and 1 DCS-942L

The DCS942 (which is right near but facing the other direction) is about 2 meters away from one of the 932's but the 942 keeps going offline - it comes back on and off probably 4-5 time during a 24hr period.

This is most frustrating - it would look like Wifi signal strength could be the issue but the other 932 right near it doesn't have this issue?

View 1 Replies View Related

D-Link DCS-942L :: Unable To Reset It

Jun 24, 2012

I initially set it up for static IP, which was a mistake for reasons I probably don't need to go into here.  Having recognized my mistake, I've been trying to hard reset it so I can convince it to acquire its IP address by DHCP, but each time I reset it and return to the "First, select your camera" screen in the setup wizard, I'm faced with a single choice: the device as I first set it up for static IP.  I don't seem to be able to convince it to give up that erroneous static IP address.I have read the FAQ section on hard reset.  I've held down the reset button for a lot longer than 6 seconds while the cam was connected to power and ethernet, and I've watched it go through the sequence of flashing blue reset and WPS lights until it settles down, but this doesn't change the situation, evidently.

View 7 Replies View Related

D-Link DCS-942L :: Almost Always In Night Mode

Dec 24, 2012

My DCS-942L is almost always in night mode with IR on resulting in a B/W picture. Only when the light is very bright it changes to day mode. How to adjust the day/night threshold?

View 11 Replies View Related

D-Link DCS-942L :: Can't Connect To The Rtsp

May 5, 2013

I'm trying to connect to the camera DCS-942L  through the Rtsp Protocol.

Link do this : [URL]

But the video signal no. Tried different players. Players determine the model of the camera , but no image and after a couple of minutes is open. What I'm not doing all right?" My link has the correct view ?

View 3 Replies View Related

D-Link DCS-942L :: How To Mount In Window

Dec 13, 2011

Any replacement bracket or some other way to easily mount the 942l in a window? i have a long window next to my front door i want to just stick this someone about shoulder high in that window looking right to the door so will see anyone who comes.

View 5 Replies View Related

D-Link DCS-942L :: NTP Not Functioning Properly

Jan 27, 2013

My Dlink DCS-942Ls had been updated to the latest firmware both 1.12.1608WW and 1.12.1628EU. (I grouped them into two firmware devices). They are all H/W version A1, agent version 2.0.15-b11.  If I setup time to automatic time configuration and sync with NTP servers ( all from drop down list and Thailand NTP server time1.nimt.or.th) , they did not work and I must set time manually every times I power off and on these IP cameras.  I knew that this issues has been raised for long times and still exist in the current firmware.Simple way to eliminate this problem is specifying NTP server into IP number.  ping your national NTP server URL and then get the IP address , e.g. time1.nimt.or.th has IP 203.185.69.60 , or ntp1.dlink.com has IP 61.67.210.241.  I have tested many ways and the results can be comfirmed that  URL NTP letter cannot sync time but IP number can do.   I also has a DAP-1360 Repeater mode and test with its "System Check" ping test,  the result are success either URL NTP server name and IP number.  NTP protocol is different to ping test. I'm not sure that which parties (ISP, DNS, Router, IP camera device)  should fix this error.    I decided to specify NTP server with IP number to all network devices from D-Link.  Minor risk may occur if a national NTP server change its IP number.

View 1 Replies View Related

D-Link DCS-942L :: Getting Error 324 On Firmware Update

Sep 2, 2012

I get this error when I update to 1.12. Error 324 (net::ERR_EMPTY_RESPONSE): The server closed the connection without sending any data.

View 3 Replies View Related

D-link Dcs-942l :: Do Not Upgrade Firmware Over Wifi?

Jun 25, 2012

Well this one should be in the "Firmware DOs and DONTs" post. I updated to FW 1.11 over wifi and apparently this will corrupt the camera so it needs serviving. Would have been nice to know that before I did it. Since the upgrade from 1.02 1030 I get this note:The throughput of the SD Card on your camera is not currently enough for recording. We suggest you to reformat the SD Card or replace it with a higher class one.

View 12 Replies View Related

D-Link DCS-942L :: Cannot Update Motion Detection

Nov 2, 2012

I have been having no luck with DLink support getting an answer. I have the DCS-942L which allows me to set the date/time zone but when I try to add motion detection settings the page always times out during the save. I tried using CaT-5 CABLE instead of wifi for settings (camera on same router and desktop pc) but after the "saving" message appears, it eventually times out and I have to click the Back arrow to return only to find none of my settings saved. I also want to note that each time I log in I see a broken certificate error message. Using Win8 with IE10. Also tried on Win7 with IE9 and XP Pro with IE8.

View 3 Replies View Related

D-Link DCS-942L :: How To View Camera For Outside Network

Jan 4, 2012

I have a new apple airport extreme wireless router and have done all the port forwarding and gave the camera a static address and cannot view my camera outside my network. I also have done the dyndns service also. I will note if I change the http port in the camera settings to say 82 I get a black screen and cannot view my camera till I switch back to port 80. Reason why I want to do this is I need to view my camera for more then 60 seconds.

View 5 Replies View Related

D-Link DCS-942L :: Camera Is Not Recording In SD Card

Dec 27, 2012

i bought wireless camera dcs942l everything works but my sd card 32 gb is not recording the camera is not recording in my sd card i formated sd card still not recording camera works good quality picture network working but not recording on my sd card and i can not record in my computer

View 5 Replies View Related

D-Link DCS-942L :: Getting FTP Option To Work With This Camera?

Jan 18, 2012

Has anybody gotten the FTP option to work with this camera?  And if so how did you set up the path to point to the ftp share.  The instructions say one thing but that one thing doesn't work.  FTP is setup locally on my NAS box which does work.  Or is this another one to add to the Firmware which list? 

View 4 Replies View Related

D-Link DCS-942L :: How To Copy Video Files From SD To PC

May 14, 2013

I record videos after motion detection on the cameras sd-card. Is there a way to copy all the files from sd-card to the pc? I wasn't able to copy them with the web-interface. I don't just want to delete the videos from time to time. I also want to archive them local.

View 3 Replies View Related

D-Link DCS-942L :: Video Clip Notification (MP4 Instead Of AVI)?

Feb 11, 2012

Can the DCS-942L be configured to send the "Video Clip Notification" email video attachments as MP4 as opposed to AVI?  The iPhone can not play AVI files, so I'm forced to use the snapshot feature which misses a lot of the motion.  I have a Linksys WVC80N that allows me to send video email attachments in MP4 format that works great, but I would like to have this ability on my two D-link DCS-942L cameras as well.  If there is no way to send MP4 video email attachments... is this something that could be added as part of a firmware upgrade? 

View 4 Replies View Related

D-Link DCS-942L :: Not Working Over Wireless With SD Card

Dec 14, 2012

My DCS-942 is doing everything quite well, except when an SD card is inserted.  When connected to the network via ethernet, everything works well.  I can set detection zones with snapshot or video modes and it does what I want it to do, however, as soon as I remove the ethernet cable and wish to use the camera over wireless, the unit fails to work at all (red light illuminated).  If I then remove the SD card, it will work over wireless again with all the capability except for SD oriented operations.  I have performed several hard resets and formatted the card with no success.

View 2 Replies View Related

D-Link DCS-942L :: Emails Blocked As SPAM?

Jan 30, 2013

Yesterday I had the snapshots setup to be sent to my gmail account and now they've been blocked as spam.  Is there anyway to get around this?  The motion detection area is set to 90% so I see why I'm getting a bunch of snapshots.  Is there a setting I can change on my gmail account or is the only option to reduce the percentage?  I'd prefer to get all of the emails.

View 2 Replies View Related

D-Link DCS-942L :: Changing Settings Remotely?

Apr 8, 2012

I need to change my DCS-942L camera settings remotely when I am not connected to my home wireless network.  When I am at home, I just type in the local IP address of the camera (192.168.0.100) into my browser to access the firmware.  How can I do the same when I am away from home and obviously not connected to the local WiFi?

View 1 Replies View Related

D-Link DCS-942L :: Network Attached Storage

Feb 11, 2013

Anyone using it to save videos from their cams? Are you using Synology NAS? Am interested and want to hear from people qualified to discuss NAS. Qualified means you are currently using NAS or have thoroughly researched it to the point you have made your purchase decision for the most part.

View 6 Replies View Related

D-Link DCS-942L :: Continuous Recording To External PC?

Feb 28, 2013

I would like to record the camera feed (per 5 min. files) on my server (ubuntu or windows)

I Installed a FTP server and tried the option "always" in the "video clip" section, but unfortunately, it seem not possible to record more than 10 seconds files every 60 seconds  . I think that this is a bug ?

Do you know, if we have a possibility to record the camera feed, I would like to manage it from the webcam or with an external program running as a service.

View 7 Replies View Related

D-Link DCS-942L :: Unable To View Video?

Jul 15, 2012

My camera saves video as .avi files, but when I open them in Media Player, all I get is sound. The camera works fine, as I can view live video, but the saved files show nothing, just have sound.

View 4 Replies View Related

D-Link DCS-942L :: Can't Access Into Camera Interface With 192.168.1.100

May 12, 2013

Months ago i can enter in the camera interface by using 192.168.1.100  , its correct ip to enter in the cammera ?  Now i dont know what is happening i connect the ethernet cable correctly  from PC to the camera and i type in the browser : 192.168.1.100 but nothiung happen ?

View 4 Replies View Related

D-Link DCS-942L :: Night Vision Is Not Working?

Mar 28, 2012

Just set up 2 dcs-942 cams, and both were working fine. Now for some reason, the ir on one is not working, or very dim.  This is in complete darkness, and its not seeing anything beyond 3ft.  I've tried unplugging it, but didn't work. I haven't tried a hard reset yet, but may have to.  Btw, no difference even if I force dark mode. 

View 3 Replies View Related

D-Link DCS-942L :: Cameras Time Keeps Resetting?

Mar 23, 2012

On one of my cameras time keeps resetting as if power was turned off then on again. It happens 2-3 times a day. I think there is no way to resolve it other than replace the camera.

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved