D-Link DIR-825 :: Blocking Access To Website?

Apr 20, 2013

For the last week, I haven't been able to access my banking web site (Royal Bank in Canada).  It doesn't matter which browser (FireFox, IE, Chrome) or computer (desktop, laptop) or even my cell (on WiFi).It must be the router (DIR-825, HW-B1, FW-2.07NA) since I can connect to the web site fine if I connect straight to the modem.  (Also, if I turn off WiFi on my cell, I can connect to their web site but once I turn WiFi back on, it wont connect).I tried restoring to factory settings but that didn't work.I tried some of the suggestions here: http:[url].....

- Turn off ALL QoS or Disable Traffic Shaping. Advanced/QoS.

- Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.

- Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking

- Ensure devices are set to auto obtain an IP address.

- Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.

- Enable uPnP and Multi-cast Streaming under Advanced/Networking.

View 3 Replies


ADVERTISEMENT

D-Link DIR 655 :: Blocking Website Of Admin

Apr 5, 2011

I have a dir-655 a3 router that is blocking my website ip address.I could previously access this site until one day, without changing any router settings, it started blocking communication to my website. pings, tracerts, web browsers, everything simply times out. It resolves the IP address ok but doesn't go any further than that. I was on firmware 1.31 and have now upgraded to 1.35NA, but no luck. I have also tried resetting factory defaults to no avail. If i bypass the router and plug my computer straight into the modem, the site loads fine. so its definitely the router. I have tried this on a number of devices to make sure. It appears that for some reason the router is blocking that specific IP address as it is on a shared hosting and I can't access any other sites on the same IP address. Does the router check the IP address with any web service before returning the request?

View 4 Replies View Related

D-Link DIR-615 :: Blocking Not One Specific Website But All Websites?

May 16, 2013

In Setup > Parental Control it is possible to set rules attached to specific website URLs. I want to block access from 1am to 6am.

However these rules only apply to websites URL. Is there a way to apply a rule to ALL websites at once? I tried to enter "*" or "*.*" in website URL field but it doesn't work.

View 1 Replies View Related

Routers / Switches :: D-link Router Is Blocking Website?

Feb 27, 2011

l have a web-site and when l go on it it comes up with blank page internet explorer cant load this page.l have phone talk talk and they cant fix it.l have a d-link router,its only my own web-site l cant access all other web-sites l can access.

View 2 Replies View Related

Cisco Routers :: RV110W Internet Access Policy Website Blocking?

Sep 30, 2011

I have an RV110W running firmware version 1.0.1.6 and I am trying to figure out how to enable website blocking in the Internet Access Policy screen. The Add Row button is grayed out in that section, as are the associated checkboxes.
 
Is there something else one needs to do to enable this feature?
 
If I set a name etc. at the top, and click save, it tells me "You must at least set a website blocking or PCs rule," so it is not the case that one has to save some information before continuing!

View 10 Replies View Related

Linksys Website Blocking?

Jan 24, 2011

How do u lock your wirless router connection so other people. Can't get on it

View 2 Replies View Related

WRT160N V3 Wireless Router Blocking Website?

Jun 23, 2012

I'm using a WRT160N v3 wireless router and it is somehow blocking my website. It works when connected directly to modem.

View 1 Replies View Related

D-Link 855 Router - Blocking Internet Access?

Aug 6, 2012

Im using d-link 855 router to block internet to certain machines, using access control within dlink and then in putting the ip for the right machines. But it seems the machines keep changing the IP adresses everything they boot thus getting internet access the next day.

View 14 Replies View Related

Linksys Wireless Router :: E1000 Website Blocking

Jul 29, 2011

is there a way i can block a website from being viewed.i would like to do this from the setup page of my e1000 under website restrictions.

View 1 Replies View Related

Linksys Cable / DSL :: DG834GT Website Blocking By Keyword

Feb 18, 2011

WAG320 allows website blocking, to enable this you can use a keyword. I would like to use this function to block anoying advert sites (in the same way I could with my Netgear DG834GT) - However the way this function has been implemented is less than ideal.
 
e.g. when a site is blocked by the router, the router does not return a response - this is great until that site forms only part of a web page that is permitted. What then happens is the web page takes forever to load as the responses have to timeout for the blocked components.
 
The way this function *should* have been implemented, is the router should return a blank response for each of the blocked sites. Netgear do this and it works a treat, they even put up a banner saying "Website blocked by Netgear".
 
This is such a simple feature, why has Cisco overlooked this and how do I go about raising a product enhancement ? I've been through the helpdesk which quite frankly is a farse, they asked me to reflash my firmware which surprisingly didn't resolve the issue - they then told me to send them the unit back because it must have a fault !?!? (and I have to pay for postage of course!) I explained the issue about 5 times, but the operator on the other end was just a script reader and I could not speak to an engineer - very poor.

View 2 Replies View Related

Linksys Wireless Router :: E2500 Is Blocking Website

Mar 19, 2012

I have a Linksys E2500 wireless router. It seems to be blocking a website (evernote.com). I cannot access this site from any of the computers/ devices in our house, whether they be connected by ethernet or wireless.  However, when i move to a different network, I can connect to this site immediately from exactly the devices that do not connect in our house.
 
How can I determine how/if the router is somehow blocking this site? I have reset the router and upgraded the firmware. Same problem persists.  I see nothing in the router settings that would be blocking this site, and I have certainly done nothing intentional in the settings to block this. We used to be able to connect to this with no problems, but all of a sudden, we are blocked.

View 5 Replies View Related

D-Link DIR-655 :: Log Access To Website

Jul 7, 2010

Is there any way to log if a URL/website has been accessed?  It seems that the "Access Control" section would do this, but I don't know how this works nor how to view the logs.

View 2 Replies View Related

D-Link DIR-655 :: Blocking Access To Websites Doesn't Seem To Work

Feb 26, 2012

Like others I see on this board, we've got middle- and high-school age kids whose access to FB and other sites needs to be controlled/scheduled.

I thought the DIR-655 was great, in that it has features that, on the face of it, would seem to be ideal for blocking domains and restricting access.

My problem:  I've never been able to get this to work.

I've set up schedules and created lists of domains that I want to limit access to according to the schedules, but the only constraint I've ever gotten to stick is blocking access completely to the router.

*None* of the schedule-based or website-based access controls have ever worked; I'll put the block in place to my daughter's computer's MAC address so she shouldn't be able to get to youtube or facebook, save, bounce the router, but then I go by her room and she's still busily chatting away online to her FB friends.

Based on similar posts I've seen on this forum, this may not be a unique problem.

So in a nutshell, this is what I want to do:

1) Block certain computers (identifiable by MAC address)

2) from being able to get to particular named domains (and any of their sub-domains)

3) according to a schedule that I can create and modify.

My preference would be to do this in the router, but again, responses I've seen here suggest that may not be possible.

View 1 Replies View Related

Monitoring / Website Blocking Software To Install On Work Wireless?

Mar 8, 2013

I would like to set up a monitoring/site blocking system where I work (owners request) to black sites like Facebook, YouTube, etc. Are there any decent, basic freeware ones out there?

View 1 Replies View Related

Security / Firewalls :: WRT54GL Linksys Router Website Blocking?

Aug 4, 2011

I am tying to block a certain website on my WRT54GL Linksys router.I have put in MAC adresses on the Access Restrictions tab but its still not working.

View 3 Replies View Related

Linksys Wireless Router :: Setting Up Website Blocking On WRT310N?

Sep 12, 2009

Setting up website blocking.  I have set up access restrictions for selected times and days but I also want to set up access restrictions for webistes.  Perhaps I'm just not clear on how this is supposed to work - I created a policy called 'Site' and then enter the URL in the website blocking area.  The options under the 'Access Restrictions' area are either 'Allow' or 'Deny' - intuitively one would assume the selection should be 'Deny' since this policy is to block access to specific URL's.  However, if I click 'Deny' and then save, then the URL's I just entered are cleared.  However, if I select 'Allow' then I am essentially giving 24hour access every day to my computers (but blocking the URLs), which then seems to go against the access restrictions I set up for selected times and days.  Perhaps these two policies are mutually exclusive but it does not seem clear that it is.

View 2 Replies View Related

Linksys Wireless Router :: Cisco WRT120N Website Blocking By URL Address

Jun 14, 2010

I've been given the task of blocking access to certain websites, facebook, youtube, etc The router is the Cisco Linksys WRT120N
 
Ive entered the web addresses in the Website Blocking by URL Address boxes on the internet access policy page but it doesnt seem to work no matter how i do it.
 
Ive tried to deny internet access but that shuts of all internet access.

View 9 Replies View Related

D-Link DIR-655 :: Website Filter / Access Control For Wireless Laptops

May 2, 2011

I have several laptops at home that connect via wireless connection tot he DIR_655.  Using the MAC address of those laptops, I want to prevent them from going to certain websites.Under 'Advanced" and "Website Filter", I addes several domain names (websudoku.com for example).  I selected "DENY computersaccess to ONLY these sites".  I then saved settings.I then went to "Access Control".  I clicked on "Enable Access Control".I clicked on "Add Policy" to cdreate a new policy for one of the laptops.When I boot the laptop and go to one of the websites, it still allows me access.  The URL/domain name is correct. 

View 5 Replies View Related

D-Link DIR-601 :: Website Filter / Access Control Causes Dropped Connection For Non-blocked Sites

May 4, 2011

I'm trying to set up a website filter on my DIR-601.  I created a policy for 2 MAC addresses, with a schedule from 10AM-6PM, selected "Block some websites", and disabled logging.  Under website filter, I added some entries, and selected "DENY computers access to ONLY these sites".  When the policy is enabled, and I try to access one of the blocked websites, it gets blocked correctly ("The URL access was denied by administrator.")  However, for all other websites, I get "server unexpectedly dropped the connection" errors, eg "Safari can�t open the page [URL] because the server unexpectedly dropped the connection. This sometimes occurs when the server is busy. Wait for a few minutes, and then try again." or in Chrome "No data received.  Unable to load the webpage because the server sent no data."  This happens with ALL non-blocked websites.   I'm using hardware version A1, firmware version 1.01NA.

View 2 Replies View Related

Linksys Wireless Router :: Wrt54gs Router Blocking Website With Password?

Aug 14, 2011

There is a way to block access to a website by password protecting it through my linksys router, which is one of thoe wrt54gs. I know I can completely block access of a website and can restrict the viewing hours of facebook at certain times through the router admin IP site but was wondering if it was possible to make it so you have to use a password to view said certain site. If there isn't is there any way maybe through a program or do I have to go through my ISP to see if they can do what I am asking for.

View 1 Replies View Related

D-Link DCS-942L :: Searching Support Website Getting No Link

Jan 30, 2012

I have 1.00 build 0522 and searching the support website I see no link.  But reading here I see there is a later version.

View 1 Replies View Related

New TP-Link Router Blocking Application?

Jun 9, 2011

I just installed a TP-Link router. Everything (almost) works: PC internet, laptops internet, email, etc. An application on my PC can't communicate through the router to the internet server now. I am sure it is a port/IP address issue. But I am unable to figure out a solution. I have already changed the IP (of the computer with Windows 7) to a static IP address. I guess now I need to get the port access done. I know the ports in question from calling the vendor. I just need to get the application through the router.

View 1 Replies View Related

D-Link DIR-655 Blocking Port 69 Outgoing

Jan 12, 2012

within ACS 5.3, I'd like to use 2 external authenticator for the same service, like vpn remote-access.For the authentication, I know I can create an identity chain, to query SecurID and then AD, in case of user not found in SecurID.For the authorization rules, I need to provider a wide vèn access for SecurID users and narrow vpn access for AD user.Are there some parameter to use in compound conditions for SecurID ?

View 1 Replies View Related

AVG Is Blocking Internet Access?

Aug 1, 2011

Every time I turn on my PC I find I have lost internet access. I can fix this by going to Network Connections, disabling the connection, re-enabling the connection.But why does this happen? I notice the the following:1. When I look at the Network Connection it shows "Local Area Connection, Network 3, Unidentified network, Realtek PCIe....."2. When I re-enable the network AVG tells me the Firewall settings have changed - Directly Connected to Network has been set to Unidentified..... etc

View 2 Replies View Related

D-Link DIR-655 :: Blocking Specific Computers On Lan From Websites?

Apr 28, 2011

Is there a way to block specific computers on the LAN from specific web sites by the domain name? All I can see is that if I put, for example, www.facebook.com, it will be blocked from all computers on the LAN, whereas if I want to block only 192.168.1.3 for example, I have to use the IP address through the Access Control, which is much harder and ****e to some "work around" by the user.

View 3 Replies View Related

D-Link DIR-655 :: Internal Port Blocking / Routing?

Jul 14, 2012

Have a Rev. B1 w/207NA on Time Warner with a Moto Surfboard SB5150.Working with TiVo's, we've been through hell and back trying to resolve why Multi Room Viewing doesn't seem to want to work - but only one way!  The newest TiVo's their Premiere model with HD and all the bells and whistles, it sees the other TiVo and all the other software that can send programs back and forth with it.

I brought on a Series 2, which is an older model that's non HD and has some older software in it.  While the Premiere and the other PC's/Software around the building's network can 'see' the Series 2 and it can 'see' the other shared PC's, etc. the thing can't 'see' the Premiere.This has been going on for awhile, I've worked with TiVo Support also to unlock ports, IP addresses and anything else we could think of.  Still no luck.  Then we had a strange occurance!

The DIR-655 seemed to 'lock up' or disconnect from the Net.  One day I was surfing the Now Playing menu in the Series 2 and the other TiVo wasn't showing as usual.  I checked it again during a commercial for something totally different and suddenly noticed there it was!!  I thought it was weird, so I went out front to check with the person using the main TiVo if they had made any changes or done anything - they hadn't, but did mention their Net connection was gone.

I turned around and looked at the 655's status lights and noticed while all the rest were fine - the WAN/Net status light was totally out.  Not a single blink.  And then I looked at the Moto cable modem and noticed it's 'activity' light was also totally dormant.  I twisted the Moto to get a better look at it and things started working again, I tightened the cable modem cable on the rear and that was it.

From that point on - once again, the front TiVo won't show on the back TiVo!  Does every other way, but not that.  In our discussions on TiVo we thought it could've been the cable modem firewall or something, but I retested it and this time it had NO effect.  Tried not only taking out the cable-cable but the Ethernet cable as well to ensure all were tested.  Still didn't now up.  What I thought was going on was the 655 had turned into a giant 'Hub', which would've caused the TiVo's to use their old-fashioned Beacon software to 'find' each other.  When the 655 software kicked back in from that glitch, the hub setup would've obviously stopped and the 655's software settings would've kicked back in.

I have a complete list of the ports internally that need to be open for those two TiVo's to communicate, but I can't find anything in the 2.07NA GUI (or Help manuals) that tell me how to write a rule to open those ports internally.  I wouldn't think there's any internal blocking or firewalling going on (I have it set to allow communications between clients on the internal Net) but there's so many settings in this GUI it makes your head spin!

View 14 Replies View Related

D-Link DIR-655 :: Router Blocking University Sites

Jan 13, 2012

So I can't seem to access ANY site related to my university (www.concordia.ca) anymore from my home network. I've tried to visit URL or any of its' sister sites from my desktop, my laptop, my iTouch, even my ps3, I've also tried cross-browsing to no avail. I've checked the router page, apparently my Hardware Version is B1 and my Firmware Version is 2.00NA. Access Control is unchecked and there are no sites at all listed under Website Filter. I've also tried resetting using the reset-hole and also by pulling off the power chord. Also did a factory-reset from the router page, the problem persists despite all of that.Every other site works just fine, it's just my university site that refuses to load up. I've browsed the last 7-8 pages of this forum, this doesn't seem to be a common problem based on that little sample. So what gives exactly? I used to be able to visit those sites just fine prior to few days ago.

View 8 Replies View Related

Blocking Individuals Internet Access?

May 21, 2012

I am setting up a network for a friend with children. He has a BT homehub and wants to block their access between certain hours. However by using access control on BT it tells you that you have been blocked which is no good as he cannot feign ignorance and pretend he doesn't know what to do (as his kids will pester him to fix it). He therefore wants to block their access more discreetly (as if the internet was generally timing out or messing up instead of actually displaying they have access control).Is there a way to block an individual's access on the router without blocking everybody either on a timer or manually done each time (thus if there isn't a way of automating it he can at least do this manually each time).

View 3 Replies View Related

D-Link DIR-655 :: DIR-635 Not Shown On Website

Feb 17, 2011

I have  a DIR-635 and is rev B3 but this is not shown on the dlink website..

View 1 Replies View Related

D-Link DIR-655 :: Blocking Traffic On Port 80 Except For Google Earth

Mar 29, 2012

I've blocked all traffic on port 80 (Advanced-Access Control- Apply Advanced Port Filter- All IP range and Port 80 selected) to avoid any kind of Web Access. I won't use Web Filter because there are too many URLs to be blocked.

However I have a problem to keep Google Earth working, since it uses port 80.

Is there a way to keep Google Earth working, even blocking traffic on Port 80? I've tried configuring an application rule to let Google Earth working, but it didn't work (it seems that I can not create an exception for Filter Port) .

View 9 Replies View Related

Cannot Access One Particular Website

Jan 21, 2012

for sometime I have not been able to access any google website. I can access all others?

View 5 Replies View Related

Can't Access One Website

Feb 20, 2013

So recently i decided to try to play some rune scape since i played it through my childhood and wanted to try again, it went fine first 2 days, and after that i can't access the website at all. I've tried to ping it, and all that comes up is that request timed out, tried flush dns, restarting router/modem and even to change ip (which i did not succeed with).However i found this "solution" url... and reading the top comment, it says that "This problem occurs when viewing the same site over a router from more that one computer or application at the same time for a period of time." And i have done exactly that in the past days the site was working.

View 5 Replies View Related

Can't Access One Particular Website

Apr 24, 2012

I'm trying to reach [URL] and just keep getting a timed out message. I had this problem before once and gave up trying to solve it and then one day I came across a post at SWI in my google results and amazingly, I was able to access the site. I have no idea what was different on that particular day.

Same symptoms in Firefox and IE so I don't think its a browser issue.

Tried accessing the site through the IP address - same result.

Tried safe mode with networking - same result

I reset my router a few days ago because of another issue but I haven't reset it since this problem began. I have tried restting my router dns to opendns and also google public dns, neither of which has made any difference.

I got a friend to confirm that the site is not down, as I suspected. Tried to ping the site using this and the only 2 UK locations on the list said 100% packet loss - is this relevant?

View 14 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved