I've been given the task of blocking access to certain websites, facebook, youtube, etc The router is the Cisco Linksys WRT120N
Ive entered the web addresses in the Website Blocking by URL Address boxes on the internet access policy page but it doesnt seem to work no matter how i do it.
Ive tried to deny internet access but that shuts of all internet access.
is there a way i can block a website from being viewed.i would like to do this from the setup page of my e1000 under website restrictions.
View 1 Replies View RelatedI have a Linksys E2500 wireless router. It seems to be blocking a website (evernote.com). I cannot access this site from any of the computers/ devices in our house, whether they be connected by ethernet or wireless. However, when i move to a different network, I can connect to this site immediately from exactly the devices that do not connect in our house.
How can I determine how/if the router is somehow blocking this site? I have reset the router and upgraded the firmware. Same problem persists. I see nothing in the router settings that would be blocking this site, and I have certainly done nothing intentional in the settings to block this. We used to be able to connect to this with no problems, but all of a sudden, we are blocked.
Setting up website blocking. I have set up access restrictions for selected times and days but I also want to set up access restrictions for webistes. Perhaps I'm just not clear on how this is supposed to work - I created a policy called 'Site' and then enter the URL in the website blocking area. The options under the 'Access Restrictions' area are either 'Allow' or 'Deny' - intuitively one would assume the selection should be 'Deny' since this policy is to block access to specific URL's. However, if I click 'Deny' and then save, then the URL's I just entered are cleared. However, if I select 'Allow' then I am essentially giving 24hour access every day to my computers (but blocking the URLs), which then seems to go against the access restrictions I set up for selected times and days. Perhaps these two policies are mutually exclusive but it does not seem clear that it is.
View 2 Replies View RelatedThere is a way to block access to a website by password protecting it through my linksys router, which is one of thoe wrt54gs. I know I can completely block access of a website and can restrict the viewing hours of facebook at certain times through the router admin IP site but was wondering if it was possible to make it so you have to use a password to view said certain site. If there isn't is there any way maybe through a program or do I have to go through my ISP to see if they can do what I am asking for.
View 1 Replies View RelatedI am tying to block a certain website on my WRT54GL Linksys router.I have put in MAC adresses on the Access Restrictions tab but its still not working.
View 3 Replies View RelatedI'm using a WRT160N v3 wireless router and it is somehow blocking my website. It works when connected directly to modem.
View 1 Replies View RelatedMy router,EA4500 is blocking just one I.P address,(a game server), and I am unable to connect to the server. I have tried this on 2 different computers, reinstalled the Cisco Connect software, reset to factory defaults and it is still blocking me from getting on this server. When I by pass the router and plug directly into my modem the Server shows up fine and I am able to get on but when I put the Router back it blocks it and does not show up at all.
View 1 Replies View RelatedMy Linksys WRT120N router doesn't accept my cellphone's MAC address... Phone's MAC address is AC:81:F3:08:13:F5 but upon adding the MAC address Internet Access Priority Category based on MAC address, I get an error "Assign MAC address is incorrect".
View 1 Replies View RelatedHow do u lock your wirless router connection so other people. Can't get on it
View 2 Replies View RelatedAfter an upgrade of the WRT120N to firmware Ver.1.0.06 (Build 01) every device I have tried to use WPA authentication with will authenticate / associate with the device then drop the connection just prior to recieving a DHCP address.I have tried a Dell latitude laptop with the broadcom chipset, an iPhone 3GS as well as an motorola with google pad device and all experience the same problems.I have removed all mac address filtering, and re-enabled the essid broadcasting only to have the same problem persist despite stripping everything down to just WPA.
View 2 Replies View RelatedWAG320 allows website blocking, to enable this you can use a keyword. I would like to use this function to block anoying advert sites (in the same way I could with my Netgear DG834GT) - However the way this function has been implemented is less than ideal.
e.g. when a site is blocked by the router, the router does not return a response - this is great until that site forms only part of a web page that is permitted. What then happens is the web page takes forever to load as the responses have to timeout for the blocked components.
The way this function *should* have been implemented, is the router should return a blank response for each of the blocked sites. Netgear do this and it works a treat, they even put up a banner saying "Website blocked by Netgear".
This is such a simple feature, why has Cisco overlooked this and how do I go about raising a product enhancement ? I've been through the helpdesk which quite frankly is a farse, they asked me to reflash my firmware which surprisingly didn't resolve the issue - they then told me to send them the unit back because it must have a fault !?!? (and I have to pay for postage of course!) I explained the issue about 5 times, but the operator on the other end was just a script reader and I could not speak to an engineer - very poor.
l have a web-site and when l go on it it comes up with blank page internet explorer cant load this page.l have phone talk talk and they cant fix it.l have a d-link router,its only my own web-site l cant access all other web-sites l can access.
View 2 Replies View RelatedI would like to set up a monitoring/site blocking system where I work (owners request) to black sites like Facebook, YouTube, etc. Are there any decent, basic freeware ones out there?
View 1 Replies View RelatedFor the last week, I haven't been able to access my banking web site (Royal Bank in Canada). It doesn't matter which browser (FireFox, IE, Chrome) or computer (desktop, laptop) or even my cell (on WiFi).It must be the router (DIR-825, HW-B1, FW-2.07NA) since I can connect to the web site fine if I connect straight to the modem. (Also, if I turn off WiFi on my cell, I can connect to their web site but once I turn WiFi back on, it wont connect).I tried restoring to factory settings but that didn't work.I tried some of the suggestions here: http:[url].....
- Turn off ALL QoS or Disable Traffic Shaping. Advanced/QoS.
- Turn off Advanced DNS Services if you have this option under Setup/Internet/Manual.
- Setup DHCP reserved IP addresses for all devices ON the router. Setup/Networking
- Ensure devices are set to auto obtain an IP address.
- Set Firewall settings to Endpoint Independent for TCP and UDP under Advanced/Firewall.
- Enable uPnP and Multi-cast Streaming under Advanced/Networking.
I have a dir-655 a3 router that is blocking my website ip address.I could previously access this site until one day, without changing any router settings, it started blocking communication to my website. pings, tracerts, web browsers, everything simply times out. It resolves the IP address ok but doesn't go any further than that. I was on firmware 1.31 and have now upgraded to 1.35NA, but no luck. I have also tried resetting factory defaults to no avail. If i bypass the router and plug my computer straight into the modem, the site loads fine. so its definitely the router. I have tried this on a number of devices to make sure. It appears that for some reason the router is blocking that specific IP address as it is on a shared hosting and I can't access any other sites on the same IP address. Does the router check the IP address with any web service before returning the request?
View 4 Replies View RelatedIn Setup > Parental Control it is possible to set rules attached to specific website URLs. I want to block access from 1am to 6am.
However these rules only apply to websites URL. Is there a way to apply a rule to ALL websites at once? I tried to enter "*" or "*.*" in website URL field but it doesn't work.
I have an RV110W running firmware version 1.0.1.6 and I am trying to figure out how to enable website blocking in the Internet Access Policy screen. The Add Row button is grayed out in that section, as are the associated checkboxes.
Is there something else one needs to do to enable this feature?
If I set a name etc. at the top, and click save, it tells me "You must at least set a website blocking or PCs rule," so it is not the case that one has to save some information before continuing!
We have a Cisco 2911 router in our company. I didn't set it up myself nor I was involved. I only started working here recently, bit over 3 months ago. I have been given ongoing task which other IT Technicians been struggling for almost a year with a idea that maybe because I'm fresh person in the company I will find a original idea why could this thing not work.
Our router have a problem with blocking a single IP address, but not completely It's hard to explain but I will try my best. Company is hosting their website externally and accessing the host and FTP on the host on daily bases. It is important for the website to work on the internal network in company. It does work sometimes, but from time-to-time the website showing time-out error 118 on any point before Cisco router using both http and https, have tried putting just the IP address( doesn't matter is it on the general network or last ISA server on DMZ ). I am able to connect to the website using any of proxy gates but not directly to the website. I have also tested the connection past the router and I was able to connect to the website without any problems. I am also able to ping the host's address from the router and internal network.
I have eliminated the possibility of not correctly setup proxy or firewall on the network as problem also occur on the DMZ. I have also checked access-lists on the router and firewall rules for Any possibilities and I can't really see a way why would the router do this.
Linksys WRT120N to 811.11n? I set to 811.11N Only with 40Mhz, saved and reboot the device but the signal continuous in 811.11g.
View 3 Replies View RelatedHow to reset the linksys cisco wrt120n router.
View 4 Replies View RelatedIs Linksys WRT120N still supported by cisco? I ask this because of the WPS "CRITICAL" vulnerability and no news of a patch since a month... and
*WRT120N firmware is propietary
*Not supported by DD-WRT/OPEN-WRT/FREE-WRT
My Cisco Linksys WRT120N router keeps disconnecting, my family and me are all using the wireless connection. But sometimes the router just disconnect us all, its like its restarting, it only close down for like 5 - 10 secounds and then its back on. Sometimes it does it like every secound hour and sometimes it does it 3 times in 10 min. I usually play games on it and even tho I am the only one using it, it still disconnects. We got 2 wireless cameras running on a secound router that is merged (Thats what the nerd that setted it up for us told me) with the primary existing router. I am not really that good at computer I just dont want to get disconnected all the time.
View 1 Replies View RelatedI've had this router for years. I have 2 servers always on, 1 computer with skype, and a 2nd linux machine with ports SSH, bittorrent, and SFTP open. Nearly all the port forwards are assigned to support this.
I got a brand new desktop with lots of CPU/Ram and was using it for development. The network card kept "going out" I would be online and all of a sudden no connections would go out from it.As I tested and diagnosed it I found it still got and held a valid IP, received DNS, but no HTTP or FTP connections would work externally. If I tried to HTTP or FTP to any computer locally on the network it would work fine. But try to access the internet and it was nothing. Restaring the machine would solve it but only for a while, usually run normally for 10-15 minutes then lose network again.. re-installed the drivers, the OS, but the problem remained. I shelfed the unit figuring it was an internal problem with the desktop since it was the only machine.Recently I got a refurbished laptop. to my surprise, it began doing the same thing as soon as I used it! exact same symptoms. So I pulled the old desktop out and it runs completely fine now! the problem has 'transfered' from the desktop to the laptop so I now believe its the router. The router does it to both wired and wireless devices, and seems to target one device at a time to be bitchy to. Allows them to run for a while and then blocks all outgoing port 80/443/21 from that device.
Firmware Version: v2.0.03 Because of DNS issues with the modem the static DNS is transfered directly to my service providers DNS machine NAT enabled, all other advanced routing disabledSPI is onall Internet filters are on, all Web filters are off on FirewallVPN functions disabledAccess Restrictions are offAll Single Port Forwarding slots are directed to 2 machines (which have no problems)No port range triggeringno DMZ or priorities set on QoS
Everything that I know to check for (security, filters, restrictions) are showing errors or something that might cause this. I believe it may be related to the IP expiring, and when the IP renews the router stops permitting its traffic outbound.
I bought a new Linksys WRT120N modem which is working great, but the wireless for some reason isn't working properly. My computer is able to sense the exsistence of the connection tho. I've tried using other computers to connect to it, and still the same problem, can sense but cannot connect.
View 8 Replies View RelatedI currently have a network using ipaddress 10.1.x.x and 10.2.x.x and 10.3.x.x with a subnet of 255.0.0.0 I purchased 2 of the wrt120n wireless routers for testing and find I can not use the subnet of 255.0.0.0.
View 9 Replies View RelatedI have a WRT120N and have been trying to set up priorities using the QoS under the tab Applications and Gaming. Everytime I "Save Settings" it does not save. It refreshes the page and deletes everything I just set up.
I did Live Chat and they told me it was my router. I returned it and got another one... Same problem
I'm using an Static IP adress and i'm using wrt120n router, but to connect the internet i have plugged the internet cable in the 1,2,3,4 (doesn't matter which one) slot. So now i'm just using the wirelss part of the router without "routering" if i can say so. When i put the internet cable in the Internet slot of the router, the laptop just cant connect to internet - it shows Unidentified network without Internet Access. I don't know what type of changes i have to make in the WEB interface of the router. I think i have to set the type of the connection - now is DHCP and may be to put my IP adress, DNS, Subnet mask in the router settings, but don't know how exactly. I've tried to set up the router with the CD-interface but same thing happened - Unidentified network when the cable is plugged in the Internet (yellow) port. How to set up the router to be a router, not just a wireless switch?
View 9 Replies View RelatedMy roommate and I recently got a WRT120N to replace an older Linksys router that was exhibiting the same problems with less frequency. Indeed, the entire reason we got the new router was to fix these problems. Alas, they have become worse.Anyways, what's happening is that the router constantly resets itself. It does this every 20 minutes to an hour and doesn't seem to be related to how much traffic it's dealing with.It's not just the internet going down, it's the entire network, and not even just the wireless part. My computer has a wired connection to the router and, and I get told "A network cable has been unplugged" every time it happens. Then, if I look down at the router, I see no flashing lights, just the steady glow of the power light. It always fixes itself after 10-15 seconds, but it's very annoying. Certainly, playing games online or having a conversation on Skype is made more difficult.As previously mentioned, we replaced our older router because it was exhibiting the same behavior, but the new one does it with greater frequency. At the very least, the router does reset itself instead of needing us to cycle the power. The setup was slightly different with the old router: I was using a wireless connection with a WMP54Gv4 which I've had to disable since it bluescreens the moment it so much as sniffs a signal from the WRT120N?
View 9 Replies View RelatedIs there anyway to disable WPS on the WRT120N router?
All I can do is switch the "view" from WPS to manual configuration in the management console...this doesn't actually disable anything.Maybe I don't understand WPS security, but what's the point of using a 20 character WPA2 password if WPS has an 8 digit PIN that I can't change or disable?
I just bought a WRT120N to set up with my new Gateway Windows 7 64-bit using Cablevision cable internet. When I go through the steps from the CD to install, the wizard does not find the connection. When the internet is plugged directly into the computer, it works fine. If I have the router plugged in first and then run the install CD, it picks up the router as an existing router but I can't get it to install
View 4 Replies View RelatedI have a WRT120N router installed in my office.All PC and Laptops are connected to it via WiFi.there are about 3 PC and 4 Laptops.The WiFi keeps going Off now and then..and comes back on in a minitue or so.
View 9 Replies View Relatedwhy are some of the lines solid & others dotted on the map page?
View 4 Replies View Related