D-Link DIR-655 :: How To Access DSL Modem Setup Pages
Apr 16, 2011
I would like to be able to access my DSL Modem's http setup screens from my networked computers via my DIR-655 (rev B) router - but I do not know how to get the router to route to the WAN port.
At first, I had my DSL Modem's LAN IP at 192.168.0.1 and my DIR-655 at 192.168.1.1 and the rest of my home network at 192.168.1.xxx; because I had read on a forum that having the modem on a different subnet prevented potential routing problems. When I pointed my web browser to 192.168.0.1 - it would just timeout (I kind of expected that).
Now (willing to try anything), I have my DSL Modem's LAN IP at 192.168.0.2 and my DIR-655 at 192.168.0.1 and the rest of my home network at 192.168.0.xxx (DHCP range is set to assign hosts from 64 to 254). When I point my web browser to 192.168.0.2 - it still just times out.
The DSL Modem is setup in transparent bridge mode. And everything else is working well with the home network.
How can I get the DIR-655 to pass/route my http connection to the DSL modem?
View 10 Replies
ADVERTISEMENT
Jan 16, 2012
Just bought myself an 825. I've got it set up and working, but how do I prevent wireless users from accessing the setup pages for the router?
I only wish wired access to the setup pages. I'm used to doing this on my old linksys, but can't find the setting on the new router.
View 3 Replies
View Related
Aug 23, 2011
I cannot access the WRT610n setup/management pages wirelessly from my Macbook using safari. I can access the router via wireless from iPhone and PC and I can access it from the Macbook via ethernet cable.
When I try to access the router from the Macbook I just get "Contacting..." in the Safari status line and eventually it times out.
I can access the internet using Safari via WRT610n wireless. The only page I can't access is the router's management page.
View 7 Replies
View Related
Jan 9, 2012
I have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies
View Related
Apr 20, 2011
The combination of the two line are successful and the internet is working with double speed. I can access all router from my PC but sometimes I have hard time accessing the modem pages. I am not sure the reason but I thing that when I request 192.168.2.1. the request might be sometimes taken to m2 modem , that's why the modem m1 is not found.
View 3 Replies
View Related
May 3, 2011
I have been working on this problem for the last few day and have know idea why its not working but my d link Dir-615 will not work with my qwest q100 modem.
View 1 Replies
View Related
Jul 31, 2012
My daughter is on an Army Base in the South Pacific. They have Dial up internet on their home telephone not DSL. They have high speed wireless at the base community center/coffee shop. I will be going there in 9 days to install the dir-615. She has a Dell Desktop with Vista Basic SP1, laptop with XP, IPAD2 and a NOOK Tablet. The dir-615 HVE1 with firmware 5.00na on the bottom sticker. She said she was able to go to web address, login, change the user name and password, started on the wireless configuration and she paniced. My question is basically this. by using a cat5 cable from the desktop to the dir-615 with dialup internet connected can the router be setup using the automatic method as opposed to manual. Our first priority is to be able transfer files to the 2 tablets without being connected to the internet like a switch and secondly If possible go on to the internet from a Tablet or the Laptop. I assume the second option would reuire internet sharing option when setting up the network and performance would be ugly.
Can get I get this router to work this way with just dialup to set it up
View 5 Replies
View Related
May 15, 2012
I bought the DIR 655 to put into our network as the Netopia wireless fails to connect even though we have maximum signal strength. Att advised that buying a third party router would solve this problem.I did manage to almost configure the DIR 655. I would have to connect it to the system to test it[CODE]
View 5 Replies
View Related
Apr 7, 2013
We have kids in the house and I'd like to limit their internet access to certain times of the day but because of the great amount of devices they use (phones, tablets, laptops, etc.) the only way I could think of doing that easily was to set up two wireless networks: one that the adults could use 24/7 and the other that the kids could access during certain set hours.
Here's the equipment I'm working with:
DLink DIR 615 wireless router
DLink DIR 515 wireless router
Motorola Surfboard cable modem S85101U
I plugged the DLink 615 in, set it up for DHCP client and plugged it into the cable modem. I lef the default 192.168.0.1 IP address for the device. On that router, I also reserved the 192.168.0.199 IP address and assigned it to the DLink 515.I also gave the DLink 515 device the IP 192.168.1.1 so I could administer it.I set the DLink 515 to static IP and made the IP 192.168.0.199 and the default gateway 192.168.0.1.I plugged the DLink 515 into one of the LAN ports in the DLink 615.I set a schedule on the DLink 615 to shut down internet access to the DLink 515 at a certain hour and turn it back on at another time.Everything seems to work ok, but at least once a day we have to unplug and plug the routers to reset them.
View 1 Replies
View Related
Apr 19, 2011
I'm trying to find out if it's possible to setup a 3600HGV (VDSL Gateway) as modem only and have a Netgear DGN3500 (ADSL2+) as a wireless access point. I'm aware that both are DSL modems, my reasoning for wanting to have them both hooked up is that
a) the 3600HGV has no Gigabit switch and runs on wireless G
b) the DGN 3500 has a Gigabit switch and does wireless N. So in a nutshell I want the 3600 as simple modem and the 3500 as a wireless N access point with Gigabit switch.
View 4 Replies
View Related
May 2, 2012
Just finished the setup for Canon MP780 USB printer to work with EA4500. Printer goes online only while it prints the pages. When I try to scan the document with MP Navigator it cannot communicate with the scanner as printer is essentially offline. How to setup the printer in order to perform the scan of the documents?
View 2 Replies
View Related
Jul 3, 2011
I have have my Dir-655 set up as an access point for awhile and would like to change the wireless access code. I can't seem to figure out how to access the setup menu while it is an access point to do this. How I access the router when it is set up as an access point?
View 4 Replies
View Related
Dec 26, 2011
I'm using a Dell computer CPU i7 8 gig of ram. It is wired in to the router. Why does it take so long to log into the router and bring up the different pages in the settings. I have never seen a router take so long. I have not updated the firmware version 2.02NA. I have not upgraded it yet. oh I have a cable connection. When I surf the web the pages come-up fast.
View 13 Replies
View Related
Jun 26, 2011
I needed to immediately set a schedule and block IPs, these pages are built into the router.It took forever for the pages to load it took 30 minutes to navigae 5 pages. Every time I try it.Router is good and signal is excellent but the admin router pages to configure are frustratingly slow.As a techie it is anoying, as a customer getting support by the hour spend more on a faster better quillity router were the work can be done in 1/20th of the time it takes on this router.I'd say I have a dud but once setup the router is a great performer if you do not need to admin the router further?
View 3 Replies
View Related
Dec 7, 2009
I am having issues with my freinds new DIR-825 Rev:B1 Firmware:2.02NA, The admin pages are intermittently slow to load and sometimes wont load until I power cycle the device. I am using IE8 on vista x64, and have the issue on all pc's on the network. Is there a work around for this?
View 7 Replies
View Related
Feb 20, 2013
The main router is Belkin N300 and the new one is D-Link N300 DIR-651 for extended range.
View 1 Replies
View Related
Dec 1, 2011
Setting up a home network for someone who does not know any of the settings for the router, "someone" set it up for her. A laptop running Vista was accessing the network, a cable modem is used.I added a Windows-7 desktop, no problem. Connected an HP printer to desktop, no problem. Tried to connect HP printer which has a wireless function to wireless network, no-go, cannot find the security key to configure the printer.Tried to access the router with 192.168.0.1, admin screen shows, user does not know anything about password, tried default username, Admin with blank password, no-go.Reset router,
View 5 Replies
View Related
Feb 17, 2012
I'm connecting to the internet via ADSL. The modem is in our living room and has a DIR-655 connected to it. Also connected are an IPTV set-top box and an Xbox 360. In our office room we have 2 computers and a Buffalo LinkStation hard drive connected by wire to a DAP-1522 which is working as a bridge for the wireless network created by the DIR-655. The reason for this configuration is that the set-top box refused to work with IPTV through the wireless bridge. Before we got IPTV, the bridge was in the living room and was primarily used for Xbox, while the modem was in the office and allowed all desktop PCs to connect by wire.
Ever since we've had the desktop PCs connected via the bridge, surfing has been difficult. Download speeds are good, but very often webpages simply refuse to load. The browser just says "Connecting to [internet address here]. For example, I might log on to Facebook, have the front page load and then I try to open a picture someone has uploaded, but nothing happens. Clicking links, nothing happens. Clicking anywhere, nothing happens. Put a new address in the address bar, nothing happens. It just tries to connect the addresses, but won't.After waiting a while, or restarting the browser, it might work again for a while.
Is it my new modem, the DIR-655 or the DAP-1522? All devices get their IPs from the ADSL modem to ensure proper networking between the devices. Streaming from the NAS to the Xbox is flawless.
View 4 Replies
View Related
Jan 3, 2012
I`m new here I recently purchased the dir-615. I started configuring with cd but i couldn`t get past the step where it should verify if cables are plugged in , so I did it manually. Some pages won`t load , internet speed is slow ( Both wireless and lan speed ) . I am using a PPPOE connection , I even got my ISP to check my settings, and he said it was alright but it reduces my speed by a lot. Usually I download with 1 MB/s with the router on wi-fi I hardly get 50 kb/s and on lan max is 100 kb/s.
View 1 Replies
View Related
Jan 29, 2012
I have been trying to configure some settings on my modem and to do so I must access it from it's ip (192.168.250.1). However, when I load that ip in my browser it does not connect.
My router has a private ip of 192.168.0.1 because of a Double NAT issue which I am trying to fix by going to the modem's configuration page. I am pretty sure that it is 192.168.250.1 because that is what my router ISP Gateway says, along with ipconfig in cmd when I directly connected to the modem from my computer.
By the way, I am currently connected through my D-Link 254 router which is connected to my WiMax modem.
View 2 Replies
View Related
Feb 26, 2013
I was trying to access the modem router as the admin but AT&T seems to have a pain in the butt security system from me making any changes. I wanted to forward some ports to setup my Synology DS212j Network Attached Storage (NAS). I connected my d-link router to the already setup modem router which I am now connected to. I have to run off to school but I was wondering, would I be able to forward the port off my d-link DIR-601 and be able to host my NAS server off that?
I don't have too much in-depth networking experience besides setting forwarding ports, setting static IPs, but I can't do that since I am not the admin for the AT&T router. I figure the password for the AT&T router is just defaulted to admin or blank but I haven't had time to fully test everything out.
View 4 Replies
View Related
Mar 21, 2012
Iv tried about everything you can find when you google things about not being able to access a particular website but none work checking out all security settings, deleting all cache, disabling security, checking date and time, flushdns, use opendns, try other devices (not one device in my household can get to https pages on this one site), making sure root certificates are updated, bypassing router, unplugging internet and router to ''reset'', trouble shooting with isp, website, ssl issuer, other wildblue users, other website users, other tech forum, checking for virus and malware and I'm sure there's more that I can't recall at the moment. I am not the only user of this website with a problem and all us having a problem have satellite internet (different providers), however not everyone with my satellite internet (wildblue thru dishnetwork) has this problem as I have asked here...some do some don't Wildblue ''blocking'' a website's ssl? - WildBlueWorld.com Forums
I can go to the website toontown.com but I can not access any pages that are ''secure'' or https. Can't login and using satellite internet?
View 14 Replies
View Related
Jun 6, 2012
I have a Cisco 871 router at one of my client sites.(they purchased the router from me and I sent them the router with a basic configuration on it). When they connect it after hours clients get the proper IP addresses and dhcp configuration however are unable to access the internet.We are connecting their ISP supplied router to Gigabitethernet0. They have a static address. I have been through the confirmation many times and am thinking I am missing something so simple.
View 2 Replies
View Related
Jun 19, 2012
I am am having all kinds of problems with setting up my router. I finally got the LAN stuff to work but the wireless will not work its like something is blocking it but I don't see anything. I can ping from wireless to any IP address but I cannot open up web pages. You would think this is DNS issue but I my DNS l looks to be fine and the same DNS works on the 8 port switches on LAN side without issue. I also thought maybe its something to do with ACL but I don't see anything there either.
I built this using a couple of other web posts: [URL]
The first one gets my LAN up and running, and the second one will let me get my wireless up and working and show my SSID but for some reason I am blocked from the internet as far as web pages, and perhaps blocked is not the correct term at this point as it could well be settings but in any case I cannot get there. My level of knowledge is around the CCENT 1, and part of the CCENT 2. I was studying for the first test with my home lab two routers and two older switches when I decided to buy this and since working on this my actual experience has pushed past the first test and pushing me to learn a lot of new things. Many of the things in the AP I still don't understand from IOS perspective. all that bridging is a bit confusing and its not in my videos I study for the test.
(I did find a bug with the 891W model: if you use the GUI and enable the wireless using CCP then you go into the command line and put in guest mode to show the ssid it bugs out and it will not show the SSID. You fix by going back into CCP and turning off SSID and then the command line will work and it shows up, weird huh, but anyway I just put that in here in case some other person is looking for 891W and runs across the error)
Edited: OK I am adding a piece of information. I can ping Google at 74.125.227.51 "from a my PC connected to the wireless AP" but when I Put that same IP into the browser it will not go through. So seems like ICMP is getting through but maybe HTTP and HTTPS are not? I may be on wrong track but seems related.
Note: When connected to the Ethernet switch port 0 of the same router (its 8 port switch built in as well) I can get to all websites via browser without any issues. Its only with the wireless that I cannot.
show runBuilding configuration...
Current configuration : 5658 bytes!! Last configuration change at 06:08:06 UTC Wed Jun 20 2012 by brian!version 15.0service timestamps debug [ code]...
View 3 Replies
View Related
Jan 4, 2013
I recently upgraded my DIR-655 to firmware version 2.10NA , 17, Oct, 2012.Ever since the upgrade, on a wired connection the router will occasionally not serve pages. This shows up as a DNS error, stating the DNS lookup failed. If I wait a bit and reload the page, it will sometimes resolve itself. If I bypass the router and plug directly into the modem, the problem goes away completely.This is happening on my MacBook Pro, OS X 10.7.5, any browser (I use Chrome mostly, but also Safari and Firefox have the same issue). This is not happening on my Linux laptop which I use wirelessly, or my iPhone or any of my wireless clients, though the same MacBook occasionally has trouble connecting if I DO try to use it wirelessly (I receive a connection timeout and cannot log on). I'm not certain at this point if the trouble is with the router or the computer, but it only began happening (and happened immediately) after I installed the most recent firmware.
My security setup, if for any reason it matters, is WPA2 with MAC address filtering.
View 4 Replies
View Related
Mar 13, 2012
I found out that I cant access my modem (TP-Link W8901G) config page at 192.168.1.1. I was pretty sure my ID and password is correct since I never changed them. It is also unlikely that the password got changed by other people who are stealing my Wi-Fi as I turned my WLAN on only when I requires the connection then it get turned off afterwards.
View 5 Replies
View Related
May 19, 2011
My desktop recently broke so i bought my first laptop. I have AT&T DSL and i bought a new D-Link DSL-2640B modem/router so i could have wireless internet. I installed it and i was able to use it with the ethernet cable, however when i tried to use wifi, it worked for only about 2 minutes before it disconnected.. Now when i try again it says that it is connected (full 5 bars) but it also says there is no internet access and i cannot use the internet.
Also, before, with the old modem i was able to just connect the ethernet cable to the laptop and just start using the internet. Now i have to connect by putting in my username and password provided by my ISP almost like if it was dial up. I don't know why i have to do this now but not before.
Tech Support Guy System Info Utility version 1.0.0.1
OS Version: Microsoft Windows 7 Home Premium , 64 bit
Processor: Intel(R) Core(TM) i3 CPU M 380 @ 2.53GHz, Intel64 Family 6 Model
[Code].....
View 4 Replies
View Related
Dec 12, 2012
The wireless is just beyond my computer's ability to detect. I have a D-Link WBR 1310 Router hooked up to a high gain wireless antenna-yes, clear line of sight. I have no direct access to our community modem or ISP.
View 10 Replies
View Related
Jul 31, 2012
i am using a tp link 8817 modem, i can go online normaly but i can not access the default gateway (192.168.1.1, i check it in cmd/ipconfig) it keeps asking me username and password, althought i filled them with the correct username and password.
View 2 Replies
View Related
May 24, 2012
I have configured my DIR-605L for no security. I want to provide free wireless internet for the guests that come to my house. How do I insure that guests connecting wirelessly to the 605 can access the internet only and can NOT hack into the computers on my internal house network?
[code]....
View 3 Replies
View Related
Jul 7, 2013
At my office we have a wireless modem(D-Link DSL-2750U) and all the clients are connect to it wirelessly with a wireless lan card. at the next floor we have two pc(without wireless lan card) that I want to connect them to this network, I have a switch and a wireless access point(TP-Link TL-WA701ND). my Question is that how can I connect the WAP to Modem? I set the operation mode of WAP to client and add the MAC address of it in the table of wireless modem but the clients cant connect to the network.
View 1 Replies
View Related
May 10, 2013
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
Firmware Version :
ISP :
How can u acces to the setup TP-Link WR740N router who is WDS with other router ???
I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1
How to enter in my TP-Link modem, or i can`t , only factory reset
View 5 Replies
View Related
Mar 15, 2013
Region : Others
Model : TL-WR740N
Hardware Version : Not Clear
How can u acces to the setup TP-Link WR740N router who is WDS with other router? I make changes like this , WDS with TP link (IP 192.168.0.1) with adsl wifi modem who is main ip 192.168.178.1 it`s working but ,my ip from TP-Link modem is not working (192.168.0.1),only the addrees from mu first router is working 192.168.178.1.How to enter in my TP-Link modem, or i can`t , only factory reset
View 1 Replies
View Related
