Cisco WAN :: 871w Router Not Getting Access To Web Pages
Jun 6, 2012
I have a Cisco 871 router at one of my client sites.(they purchased the router from me and I sent them the router with a basic configuration on it). When they connect it after hours clients get the proper IP addresses and dhcp configuration however are unable to access the internet.We are connecting their ISP supplied router to Gigabitethernet0. They have a static address. I have been through the confirmation many times and am thinking I am missing something so simple.
View 2 Replies
ADVERTISEMENT
Feb 1, 2013
i have a really simple home network setup using the Cisco 871W 4-Port 10/100 Wireless G Router (CISCO871W-G-A-K9). I can't figure out for the life of me what is going on. Web pages seem to "half load" sometimes (netflix, facebook, bank of america doesn't load at all, etc). It doesn't always happen. Sometimes the pages will load fine. I have tested with multiple computers so I know that it is the router itself. Below is my configuration. Ignore anything regarding the wifi. I know that isn't set up correctly. I'll deal with that later. I wanted to see if i was missing anything. Config is really basic. Attached is what one of the "half loading" web pages looks like
!
version 12.4
no service pad
service timestamps debug datetime msec
[Code].....
View 3 Replies
View Related
Dec 27, 2011
By now, I'm sure E4200 and other Router users that have twonky have noticed they cannot access the twonky configuration pages, as you have chosen to block them. Please give advanced users a work around to this, because if Twonky does not recognize our newer TV/devices, then we cannot play certain file formats without manually configuring the service.
View 3 Replies
View Related
Jul 23, 2012
I am new to Cisco and am studying for my CCENT certification. At the moment, I am attempting to correctly configure a Cisco 871W lab router. Since I have undertaken this task, I have run into nothing but problems. First off it was finding that the previous owner had left a password on it, having to purchase a new USB to DB9 adapter to pass the "break" sequence to the router, and then resetting the router in ROM Monitor mode.
Now, I cannot seem to configure the router correctly, and am quite stumped.
My ISP is Charter (cable internet), and the home network that I am using consists of a Motorola SBV5122 Digital Voice Modem, Motorola SB6120 Cable modem, and, ideally, should also include my Cisco 871W router.
When I connect my router to the SB6120 Cable modem, the router receives an IP address via DHCP and the WAN indicator light turns on.
I have a VLAN configured on the 4 switchports of the router, and it is setep to act as a DHCP server. However, when I connect my PC to rhe router via Cat5e Crossover cable, I cannot access the internet. The router gives the PC an IP address, yet all attempts to ping the PC from the router fail. Somehow, I can connect to the router via SSH though.
Furthermore, I can ping the 127.0.0.1 loopback address from my PC, but cannot do so from the router.
how to correctly configure this router to function as intended in my network situation, however, this is proving to be seemingly unsurmountable!
I have attached the config of my router along with both outputs and commands relating to my predicament.
View 11 Replies
View Related
Aug 23, 2011
I cannot access the WRT610n setup/management pages wirelessly from my Macbook using safari. I can access the router via wireless from iPhone and PC and I can access it from the Macbook via ethernet cable.
When I try to access the router from the Macbook I just get "Contacting..." in the Safari status line and eventually it times out.
I can access the internet using Safari via WRT610n wireless. The only page I can't access is the router's management page.
View 7 Replies
View Related
Apr 25, 2012
I have an 871w set up to add wireless connectivity to an existing network. When adding a client to the physical interfaces to test VLAN internet connectivity, however, a DHCP address is assigned but internet traffic on the terminal never reaches the network nor does the network recognize the IP the terminal shows as being 'connected'. Also, pings sourced from the VLAN do reach destinations. I've attached my config file, I think it's a routing issue of some kind.
10.26.99.0 is the existing network. 10.26.99.1 is an existing 871w router set as the DHCP server for that network and 10.26.99.10 is a Windows Server 2003 DNS box. VLAN 2 and DHCP pool alpha were control sets for trialing DNS settings.
View 10 Replies
View Related
Mar 14, 2013
I've been trying to get my wireless configured for the past few days with no luck. I can ping every device on my local network and I can ping outside my network and surf the web. My wireless devices can see my wireless network but cannot connect to it.
[code]....
View 1 Replies
View Related
Sep 19, 2009
I use a Cisco 871W router for my office in home -- I have Wifi working and want to add my new Blu-Ray player to the network -- I bought a WAP54G to use as a wireless bridge assuming i woudl just connect the WAP to the BLU-Ray with a ethernet cord. The instructions for installation of the WAP include connecting it to my router for the set up but the installation disk says it is not recognizing the WAP. I use Brighthouse for my ISP and the connection sequence is BH Modem to teh Cisco 871W -- the 871W directly connects to my CPU and to a Net gear FS105 fast network Switch -- the swicth connects to my VOIP phone , HP printer and external HD back-up system -- there is an open port onthe FS105 and two open LAN ports on the 871W.
I tried to install the WAP but connecting it to both the router and the swtich without luck. Is the WAP what I need to connect the Blu-Ray --- am i missing something in the set up?
View 3 Replies
View Related
Jun 19, 2012
I am am having all kinds of problems with setting up my router. I finally got the LAN stuff to work but the wireless will not work its like something is blocking it but I don't see anything. I can ping from wireless to any IP address but I cannot open up web pages. You would think this is DNS issue but I my DNS l looks to be fine and the same DNS works on the 8 port switches on LAN side without issue. I also thought maybe its something to do with ACL but I don't see anything there either.
I built this using a couple of other web posts: [URL]
The first one gets my LAN up and running, and the second one will let me get my wireless up and working and show my SSID but for some reason I am blocked from the internet as far as web pages, and perhaps blocked is not the correct term at this point as it could well be settings but in any case I cannot get there. My level of knowledge is around the CCENT 1, and part of the CCENT 2. I was studying for the first test with my home lab two routers and two older switches when I decided to buy this and since working on this my actual experience has pushed past the first test and pushing me to learn a lot of new things. Many of the things in the AP I still don't understand from IOS perspective. all that bridging is a bit confusing and its not in my videos I study for the test.
(I did find a bug with the 891W model: if you use the GUI and enable the wireless using CCP then you go into the command line and put in guest mode to show the ssid it bugs out and it will not show the SSID. You fix by going back into CCP and turning off SSID and then the command line will work and it shows up, weird huh, but anyway I just put that in here in case some other person is looking for 891W and runs across the error)
Edited: OK I am adding a piece of information. I can ping Google at 74.125.227.51 "from a my PC connected to the wireless AP" but when I Put that same IP into the browser it will not go through. So seems like ICMP is getting through but maybe HTTP and HTTPS are not? I may be on wrong track but seems related.
Note: When connected to the Ethernet switch port 0 of the same router (its 8 port switch built in as well) I can get to all websites via browser without any issues. Its only with the wireless that I cannot.
show runBuilding configuration...
Current configuration : 5658 bytes!! Last configuration change at 06:08:06 UTC Wed Jun 20 2012 by brian!version 15.0service timestamps debug [ code]...
View 3 Replies
View Related
Mar 21, 2012
Iv tried about everything you can find when you google things about not being able to access a particular website but none work checking out all security settings, deleting all cache, disabling security, checking date and time, flushdns, use opendns, try other devices (not one device in my household can get to https pages on this one site), making sure root certificates are updated, bypassing router, unplugging internet and router to ''reset'', trouble shooting with isp, website, ssl issuer, other wildblue users, other website users, other tech forum, checking for virus and malware and I'm sure there's more that I can't recall at the moment. I am not the only user of this website with a problem and all us having a problem have satellite internet (different providers), however not everyone with my satellite internet (wildblue thru dishnetwork) has this problem as I have asked here...some do some don't Wildblue ''blocking'' a website's ssl? - WildBlueWorld.com Forums
I can go to the website toontown.com but I can not access any pages that are ''secure'' or https. Can't login and using satellite internet?
View 14 Replies
View Related
Apr 16, 2011
I would like to be able to access my DSL Modem's http setup screens from my networked computers via my DIR-655 (rev B) router - but I do not know how to get the router to route to the WAN port.
At first, I had my DSL Modem's LAN IP at 192.168.0.1 and my DIR-655 at 192.168.1.1 and the rest of my home network at 192.168.1.xxx; because I had read on a forum that having the modem on a different subnet prevented potential routing problems. When I pointed my web browser to 192.168.0.1 - it would just timeout (I kind of expected that).
Now (willing to try anything), I have my DSL Modem's LAN IP at 192.168.0.2 and my DIR-655 at 192.168.0.1 and the rest of my home network at 192.168.0.xxx (DHCP range is set to assign hosts from 64 to 254). When I point my web browser to 192.168.0.2 - it still just times out.
The DSL Modem is setup in transparent bridge mode. And everything else is working well with the home network.
How can I get the DIR-655 to pass/route my http connection to the DSL modem?
View 10 Replies
View Related
May 12, 2013
I'm trying to configure WiFi on my Cisco 871w router withouth any knowledge in this area. And it's a tough one, couldn't do it just with google, hope this is the place where I can get it done right step by step if possible. Everything else works fine. I'm going to post my messy show run below. Everything I did on dot11Radio will need to be cleared I suppose.
Point38#show run
Building configuration...
Current configuration : 4072 bytes
!
! Last configuration change at 16:23:18 UTC Thu Sep 8 2011
version 15.1
no service pad
[code]...
View 3 Replies
View Related
Jan 16, 2012
Just bought myself an 825. I've got it set up and working, but how do I prevent wireless users from accessing the setup pages for the router?
I only wish wired access to the setup pages. I'm used to doing this on my old linksys, but can't find the setting on the new router.
View 3 Replies
View Related
Jan 9, 2012
I have a DAP-1513 unit but there is no section for that unit on the forum.Is is possible to access the configuration pages over the wireless connection. After setting up access to the main router via WPS, I can access the configuration pages for a few minutes after I "power cycle" the unit.
View 9 Replies
View Related
May 5, 2013
I've just started styding for CCNA. Bought a router 871W recently and spent two days straight trying to configure internet connection with no luck! I use console port to do the configs and SDM/CCP. How to do simple internet connection configs. I googled everything but it's still confusing. I can't assing any IP to FA ports 0 - 3. I used VLAN instead. But all tutorials use FA0 and when I try to assign an IP to FA0 it gives me some L2 can't be assigned or something... :/ And I'm also confused what IP address should I use for WAN. I plugged the cable from Modem to PC's LAN port and wrote down some IP addresses which I think I'll have to use to configure the router for internet connection. And here they are:
ISP IP: 76.114.54.255
SUBNET: 255.255.248.0
GATEWAY: 76.114.48.1
DHCP: 69.252.97.4
DNS: 75.75.75.75
75.75.76.76
View 32 Replies
View Related
Jul 8, 2012
Recently, I purchased a Cisco 871W Router with which to practice/study for my CCENT with. Since I have made the purchase, it has given me nothing but headaches.
I cannot access the router to configure it, as the previous owner has a password set on it to access enable mode, which he/she has forgotten.
Here is the message that I receive when I attempt to log in into the router, to access enable mode. [URL]
Apparently there is supposed to be a one-time username and password of "Cisco", but this is not the case.
I have tried to do a password recovery, following this post discussion thread: [URL]
Unfortunately, this has not worked, and I am sure that I am doing something incorrectly. I am connected to the router via console cable and have tried power cycling the router and entering the break sequence, power cycling again, and then holding the space bar down for 15 seconds. The preceding has produced no results to speak of. Following, I set my terminal emulator, Tera Term, to the baud rate of 1200, power cycled the router, and held down the space bar for 20 seconds. I then immediately set the baud rate back to 9600. Nothing occurred, once again.
Furthermore, I have followed the password recovery instructions set forth by Cisco. [URL]
Nothing has come of these methods, either, and I do not see how they would work, or even apply to my situation, as Cisco seems to imply they should, as I cannot get into enable mode, let alone privileged mode or conf t mode, as the guidelines require.
Here is some info for troubleshooting:
OS: Win 7 HP 64 bit
Terminal Emulator: Tera Term
Router is not currently connected to any sort of internet connection. Only the power cord and console cable are properly connected.
View 28 Replies
View Related
Feb 19, 2013
I am not able to connect to any webpages in normal mode, even after restarting i still have the same problem [However it works in safe mode with networking]. The network connections show that it is connected and the signal strength is excellent. I then have to keep restarting the laptop like 3 to 4 times and it works. Its kind of frustrating to keep doing this all the time and besides i am scared by restarting the laptop so many time can harm it.
View 1 Replies
View Related
Sep 19, 2012
I'm on a wired business network. Some of the machines are Windows 7 and some are XP Pro, but all of us are having issues connecting to web pages, especially pages with lots of pictures. If you refresh it a few times, it may pop up. Some don't ever come up, like weather.com. The server has the same issue, even if you connect it directly to the router.
View 10 Replies
View Related
Nov 18, 2011
I am working on setting up a Linksys router for my Dad. I am moderately competent with networking. Anyway, a glaring, and obnoxious problem I am having is everytime I load a page for the router(192.168.1.1), it does not completely load and I have to hit refresh.Now when I try to change the router settings from DHCP to PPPoE, it reloads the page, for whatever reason, and because this router wants to be irritating, it only half loads the page, so I cannot click the "save settings" button.This is what has been done to the router after being reset(red button on the back held in for 10 sec):I turned on the modem, and plugged directly in to make sure I had internet connection.I plugged the modem's ethernet into the "Internet" port on the wireless router.And finally, I plug an ethernet cable from my computer to the 1st port on the wireless router.Nothing else has been changed. I have not turned on any ridiculous settings. This half-loading router pages is driving me up the wall though. I cannot even troubleshoot the wireless connectivity because I cannot make any changes.
View 7 Replies
View Related
Jun 26, 2011
I needed to immediately set a schedule and block IPs, these pages are built into the router.It took forever for the pages to load it took 30 minutes to navigae 5 pages. Every time I try it.Router is good and signal is excellent but the admin router pages to configure are frustratingly slow.As a techie it is anoying, as a customer getting support by the hour spend more on a faster better quillity router were the work can be done in 1/20th of the time it takes on this router.I'd say I have a dud but once setup the router is a great performer if you do not need to admin the router further?
View 3 Replies
View Related
Apr 4, 2012
I dont mean a website like facebook.com, but i want it to block an individual page,such as a profile page, yet still be able to access the rest of the site? Again i'm not after facebook settings etc, but i want to restrict access to certain webpages within Lan.
View 2 Replies
View Related
Sep 16, 2011
have problem with WRT54GH, almost every second page after reload gets an error message: Error 101 (net::ERR_CONNECTION_RESET): The connection was reset. Tried both on IE, Firefox, Chrome Tried to disable antivirus, no effect, the pages still load not all the time, firmware upgraded to the latest version. Before didi not have such problem with Zyxel W330EE.
View 4 Replies
View Related
Jan 28, 2010
BEFSR81 v3.1 Current firmware 2.51.4 build 600 (09-4-2009)The Web Admin pages become dysfunctional after the router has been up 3-4 days displaying only a blank white page. Viewing the page source shows that the HTML is incomplete.I am not sure of the exact firmware version where this problem originates, I noticed it after flashing to 2.51.4 build 400 but cannot remember which version was running before the update. Just flashed to 2.51.4 build 600 last week hoping the new version had corrected the problem. Still broken.The router remains completely functional but the Web interface does not work correctly after 3-4 days.I have tried re-flashing the firmware and have gone as far as resetting the router both before and after the flash, even tried 30/30/30 resets but the problem with the Web interface remains.Re-booting the router every 3 days is not the best “solution” as my network is running DHCP. I would rather not fall back to older firmware as ver 2.51.4 build 400 corrected the DHCP errors on my Windows machines and decreased the initial connection time when machines boot up. I have read in this and other forums where others are having the same problem with this router/firmware but have been unable to find a working solution which leads me to believe the actual problem resides in the later firmware builds.
View 9 Replies
View Related
Jan 4, 2013
I am a bit green with IOS and have exhausted everything I can think of with this. The router passes the WAN test in CCP?Undoubtedly there are probably a few things in the config that are either redundant or totally unnecessary, but I have been trying a few things to solve this with very little success.I have no security stuff in here because I have triewd to keep the config as simple as possible to start with. I will add that after I get the routing working.
Here is my most recent config:
Cisco871W#show config
Using 2631 out of 131072 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[codde].....
View 4 Replies
View Related
Aug 9, 2011
I bought an 871w second hand with 124-24T IOS on it. I would like to enable QoS. When I use Cisco Configuration Professional to manage the router I click on QoS and it says it is not available. I know that the router itself is QoS capable.
This is my first time dealing with a router such as this and I wonder what I need to do to enable QoS.
View 1 Replies
View Related
Sep 18, 2011
I want to upgrade my IOS on an 871W. In order to do this I need to upgrade the memory. I have found that I need the MEM870-32F (Am I correct?).
As in here: {URL}. So if I follow these instructions: {URL}. Is that all there is to it?
View 1 Replies
View Related
Nov 26, 2011
I am getting frequent stop pages in streamed video, a message appears on my laptop saying "loading" and a red line beginning traversing the screen. Eventually the line gets across and the video begins again to stream. When I do a speed test I get around 10 Mbps both through the router wireless and hardwired connections. This happens almost every 10 minutes. I have tried rebooting the router and the problem persists
View 9 Replies
View Related
Jan 15, 2013
I have a cisco 871w router that I'm trying to incorporate into an existing network. I have FastEthernet4 (WAN port) plugged into an ISP device, which I don't have access to. I have the address set to use dhcp, which is successfully recognized and I see that the interface gets a valid ip address that I can ping with other computers on the same network.
Problems: I am logged into the router via the serial port and I cannot ping websites on the internet. I am able to ping sites that are hosted inside the WAN, but when I try "google.com" for instance, I see it sending out packets, but none are received. It resolves the hostname from the local DNS server, but there are no packets received.
I type into the console to set up the router. I'm missing a lot of stuff. This is what I've been able to piece together using google and the software manuals:
enable
config t
hostname [hostname]
interface FastEthernet 4
[Code].....
View 15 Replies
View Related
Jan 16, 2011
As soon as I add the interfaces of the router to security zones it significantly drops speed on WAN interface, below 1 Mbs. I noted this because I wasn't able to watch youtube. Moreover the bandwidth test from speedtest.net hangs and doesn't come to a result. Here below is the diagnostic example while doing that test. The question is what is going on? I have two iPhones and three computers in my network, that's it. My ISP bandwidth is 10 Mbs, so is this the router hardware limitations, or kind of malfunction or some misconfiguration down here? What could be done here ?
View 4 Replies
View Related
Sep 20, 2011
About twice a day (that I notice) my wireless loses its internet connection. All the wired machines continue to be connected to the internet but any wireless ones lose internet, though they maintain a connection with the router.
View 7 Replies
View Related
Sep 23, 2012
I have a small wireless network, which consists of three AP1121G with c1100-k9w7-mx.123-8.JEB1 ios and one 871w with c870-advipservicesk9-mz.124-24.T1. I've configured two different ssid's with individual authorisation types - ssid_1 with eap, ssid_2 with wpa. All three ap's works as it should be, but 871w authorises only eap connections, and all other types are rejected
View 3 Replies
View Related
Jul 9, 2012
Is it possible to make Any Connect VPN from IPad/iPhone to 871w? IPSec VPN is working perfectly but cant get my Cisco AnyConnect iOS client to connect. I have config webvpn and it beeing user/pw prompted but keep getting the following error:
"the required license for this type of VPN client is not avaiable on the Secure gateway. Please contact Your network administrator".
View 5 Replies
View Related
Aug 21, 2012
Below is my VPN config in my 871 and radius user config. I am unable to connect to the vpn using Cisco vpn client. I am getting one of two errors depending on what config changes I make.I believe I have the radius configured correctly because it is authentication but not 100% sure.
[code]...
View 3 Replies
View Related
