I've been trying to get my wireless configured for the past few days with no luck. I can ping every device on my local network and I can ping outside my network and surf the web. My wireless devices can see my wireless network but cannot connect to it.
[code]....
I have an 871w set up to add wireless connectivity to an existing network. When adding a client to the physical interfaces to test VLAN internet connectivity, however, a DHCP address is assigned but internet traffic on the terminal never reaches the network nor does the network recognize the IP the terminal shows as being 'connected'. Also, pings sourced from the VLAN do reach destinations. I've attached my config file, I think it's a routing issue of some kind.
10.26.99.0 is the existing network. 10.26.99.1 is an existing 871w router set as the DHCP server for that network and 10.26.99.10 is a Windows Server 2003 DNS box. VLAN 2 and DHCP pool alpha were control sets for trialing DNS settings.
I've acquired an 871W, because I'd like to use wireless, to replace my 851. I Ft Pd the 851's configuration to my FTP server and then Ft Pd this to the 871W. Save for the fact that this has a radio interface (currently shutdown), everything works save for FTP from the outside. I can not even telnet to port 21 of any of the internal FT servers. I can telnet to any other port (ssg, smtp, HTTP, https, etc.) but FTP will not pass. What's the difference?
View 12 Replies View RelatedI've a problem with my 871W. I can connect to the router by inside interfaces (LAN & WLAN) but not on WAN (Fa4). My client on the WAN is on the same subnet and I can ping 871.
View 3 Replies View RelatedWe have a Cisco 871W working as PIX, controlling external VPN connections to our private network.The configuration is very similar to the one described here - "Cisco Router as a Remote VPN Server using SDM Configuration Example" url...
About once a week, it stops working, without aparent external intervention.The ping to the external IP stops answering, and the internal IP stops answering pings also.The solution is power-off and power-on, and it starts working again ...
What is the correct way to debug this situation ?I can connect a HyperTerminal using direct cable to the 871, but dont know the relevant commands to debug this situation.
Is there any LOG I can have a look into ? Yes, I am quite new to Cisco world .By the way : "show version" says Cisco IOS Software, C870 Software (C870-ADVSECURITYK9-M), Version 12.4(15)T7, RELEASE SOFTWARE (fc3)
I have a Cisco 871 router at one of my client sites.(they purchased the router from me and I sent them the router with a basic configuration on it). When they connect it after hours clients get the proper IP addresses and dhcp configuration however are unable to access the internet.We are connecting their ISP supplied router to Gigabitethernet0. They have a static address. I have been through the confirmation many times and am thinking I am missing something so simple.
View 2 Replies View RelatedI am new to Cisco and am studying for my CCENT certification. At the moment, I am attempting to correctly configure a Cisco 871W lab router. Since I have undertaken this task, I have run into nothing but problems. First off it was finding that the previous owner had left a password on it, having to purchase a new USB to DB9 adapter to pass the "break" sequence to the router, and then resetting the router in ROM Monitor mode.
Now, I cannot seem to configure the router correctly, and am quite stumped.
My ISP is Charter (cable internet), and the home network that I am using consists of a Motorola SBV5122 Digital Voice Modem, Motorola SB6120 Cable modem, and, ideally, should also include my Cisco 871W router.
When I connect my router to the SB6120 Cable modem, the router receives an IP address via DHCP and the WAN indicator light turns on.
I have a VLAN configured on the 4 switchports of the router, and it is setep to act as a DHCP server. However, when I connect my PC to rhe router via Cat5e Crossover cable, I cannot access the internet. The router gives the PC an IP address, yet all attempts to ping the PC from the router fail. Somehow, I can connect to the router via SSH though.
Furthermore, I can ping the 127.0.0.1 loopback address from my PC, but cannot do so from the router.
how to correctly configure this router to function as intended in my network situation, however, this is proving to be seemingly unsurmountable!
I have attached the config of my router along with both outputs and commands relating to my predicament.
I use a Cisco 871W router for my office in home -- I have Wifi working and want to add my new Blu-Ray player to the network -- I bought a WAP54G to use as a wireless bridge assuming i woudl just connect the WAP to the BLU-Ray with a ethernet cord. The instructions for installation of the WAP include connecting it to my router for the set up but the installation disk says it is not recognizing the WAP. I use Brighthouse for my ISP and the connection sequence is BH Modem to teh Cisco 871W -- the 871W directly connects to my CPU and to a Net gear FS105 fast network Switch -- the swicth connects to my VOIP phone , HP printer and external HD back-up system -- there is an open port onthe FS105 and two open LAN ports on the 871W.
I tried to install the WAP but connecting it to both the router and the swtich without luck. Is the WAP what I need to connect the Blu-Ray --- am i missing something in the set up?
i have a really simple home network setup using the Cisco 871W 4-Port 10/100 Wireless G Router (CISCO871W-G-A-K9). I can't figure out for the life of me what is going on. Web pages seem to "half load" sometimes (netflix, facebook, bank of america doesn't load at all, etc). It doesn't always happen. Sometimes the pages will load fine. I have tested with multiple computers so I know that it is the router itself. Below is my configuration. Ignore anything regarding the wifi. I know that isn't set up correctly. I'll deal with that later. I wanted to see if i was missing anything. Config is really basic. Attached is what one of the "half loading" web pages looks like
!
version 12.4
no service pad
service timestamps debug datetime msec
[Code].....
upgrade IOS in cisco 4948 switch, I do not have admin right and network access
View 22 Replies View RelatedI have a RV042 Dual WAN router. What I would like to be able to do is to direct a computer on my network to access one particular WAN. For example, WAN1 is a DSL line and WAN2 is a cable line. I would like to direct a computer on our LAN to access the cable line always, even though I have Smart Link Backup set to WAN1. Is this possible?
View 6 Replies View RelatedI bought an 871w second hand with 124-24T IOS on it. I would like to enable QoS. When I use Cisco Configuration Professional to manage the router I click on QoS and it says it is not available. I know that the router itself is QoS capable.
This is my first time dealing with a router such as this and I wonder what I need to do to enable QoS.
recommend a cisco core switch and access switches in IPTV network infrastructure?I was ask to implement a network for IPTV system but i don't have idea what will be the model i will use.
Core Switch = Cisco 4503
Access Switches = Cisco 3560X
About twice a day (that I notice) my wireless loses its internet connection. All the wired machines continue to be connected to the internet but any wireless ones lose internet, though they maintain a connection with the router.
View 7 Replies View RelatedI have a small wireless network, which consists of three AP1121G with c1100-k9w7-mx.123-8.JEB1 ios and one 871w with c870-advipservicesk9-mz.124-24.T1. I've configured two different ssid's with individual authorisation types - ssid_1 with eap, ssid_2 with wpa. All three ap's works as it should be, but 871w authorises only eap connections, and all other types are rejected
View 3 Replies View RelatedI'm trying to configure WiFi on my Cisco 871w router withouth any knowledge in this area. And it's a tough one, couldn't do it just with google, hope this is the place where I can get it done right step by step if possible. Everything else works fine. I'm going to post my messy show run below. Everything I did on dot11Radio will need to be cleared I suppose.
Point38#show run
Building configuration...
Current configuration : 4072 bytes
!
! Last configuration change at 16:23:18 UTC Thu Sep 8 2011
version 15.1
no service pad
[code]...
I have a problem with myself a few other clients randomly disconnecting from my 871W. It appears that I am still associated but Windows 7 shows "Limited Access". I appear to be assosciated to the AP and I still have my ip address but I can't ping the 192.168.1.1 gateway (871W). I have also set my power plan to allow for Maximum Performance which I thought disabled PSP but the log is still showing errors.As a final note, after I reconnected by ip address (192.168.1.107) doesn't show up in "sh ip dhcp bindings" but I'm working.To correct the situation, I have to disconnect and the reconnect to the AP and then I am good for another day or close to it. Below are the log errors, config and a sh ver. [code]
View 7 Replies View RelatedI have a Cisco 871W that periodically will drop its signal. how to configure this for maximum reliability? I set it to use chanel 2462.
View 1 Replies View RelatedI know this question was asked many times, but I'm still not able to finalize my configuration on 871w. LAN part works fine, but wireless clients do not get DHCP IP. here is the config:
Building configuration...
Current configuration : 2092 bytes
!
version 12.4
no service pad
service timestamps debug date time m sec
service timestamps log date time m sec
no service password-encryption
!
[ code ].....
I'd like to have LAN and WLAN clients in same 192.168.1.0 sub net.
I have a 1242 Access Point as root and a 871W Router as a non-root bridge (Diagram attached). I have a laptop connected to Fa 0 of the 871W router.
* I am able to ping from the AP to the Router and vice versa
* I am also able to ping from the router to the laptop and vice versa
* But I am not able to ping from the laptop to the AP
All bridging commands seem to be fine. Even tried adding route commands, but none seem to work.Please find the configuration below:
Configuration on Root AP:
hostname ap
!
enable secret 5 XX
!
[Code]....
I have an 871 set up at home with 2 VLANs, both of these vlans present a strange behavior where an user is unable to ping/contact another user on the same subnet, however if users are on different subnet it seems to work [code]
According to the troubleshooting that I have done, the issue seems to be with the broadcast traffic, ARP request/reply do not reach another host on the same subnet (wireless to wireless or wired to wireless) however if the wireless device iniciates the connection to wired, it works fine.
I have tried to enable proxy arp on the different VLANs and BVI and different combinations but no sucess in order to get traffic across 2 wireless devices on the same subnet or a connection that is iniciated for a wired client to a wireless one.
I tried enabling and disabling dot11 arp-cache but no luck.
I'm trying to setup a cisco 871w router in a very simple configuration using only 1 vlan. I have the FastEthernet interfaces setup such that when you plug in a client computer into one, everything works as expected. I'm now trying to set up the wireless portion. From what I've read on the internet, I managed to bring up the Dot11Radio0 interface and the BVI interface. It's a little confusing to me, but it looks like I need the BVI to bridge the wireless interface to the vlan? I'm not sure how it works...
Anyway the problem is that I can connect to my wireless network, but after authenticating, there is no ip address being assigned to the client. I don't think I'm bridging the interface correctly or something. Windows 7 gives me a yellow exclamation icon on the wireless tray icon saying "no internet access".
Here's my config:
enable
config t
hostname [name]
interface FastEthernet 4
[code]....
what I can do to accomplish my end goal of safe public wifi and configuration.I have 2 domain controllers (for redundancy) with a split scope for DHCP and they both serve DNS. I have VLAN 2 (management), VLAN 3 (Servers), VLAN 4 (Wired Access), VLAN 6 (Wireless Access) and VLAN 480 (Outside Wireless). I have setup INT VLANs for all of these on my main router (Cisco 3550) with the ip-helper address to the DC for all but the VLAN 480. All of this works great, and the scopes are setup just like the VLANs. (ie 192.168.2.0 (management) .3 (servers) etc.)I was wondering if there is a way to have VLAN 480 get DHCP from the cisco 3550 as a random address say, 172.16.0.0 255.255.248.0?
On a side note, I have seperate Wireless Access Points for the outside. (From a guy before me) I understand you can have a guest wireless setup on the newer Access Points, and trunk (cisco term) the 2 VLANs and seperate them out with Access Control Lists so they don't talk to each other, but I would rather just give the VLAN 480 it's own DHCP from the router.
I am a bit green with IOS and have exhausted everything I can think of with this. The router passes the WAN test in CCP?Undoubtedly there are probably a few things in the config that are either redundant or totally unnecessary, but I have been trying a few things to solve this with very little success.I have no security stuff in here because I have triewd to keep the config as simple as possible to start with. I will add that after I get the routing working.
Here is my most recent config:
Cisco871W#show config
Using 2631 out of 131072 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[codde].....
I recently installed a couple of Cisco Aironet 3600 Series Wireless Access Points at a remote site. While I was at the site everything seemed OK, The clients were able to get connected to the access points, the guest network worked fine, I could SSH into the access points, and I could ping them. The problem is when I went back to my home site I tried to SSH into the access points through an ASA IPSec VPN Tunnel and it couldn’t find it. When I try to ping the access points they “time out”. I can ping and connect all other addresses (via RDP, HTTP, etc..) on the same subnet which should rule out an access list problem. A couple of notes to be aware of:
The WAP’s have the Autonomous IOS installed (Version 15.2(2)JB) The WAP’s are connected to Dell PowerConnect 5724 (Not by choice.. We are a Cisco shop, these were already there and have plans this year to replace)
I can ping and SSH with Putty to the WAP’s from the local subnet I cannot ping or SSH from a remote subnet to the WAP’s. I can access all other IP’s and Computers from a remote subnet.
I want to upgrade my IOS on an 871W. In order to do this I need to upgrade the memory. I have found that I need the MEM870-32F (Am I correct?).
As in here: {URL}. So if I follow these instructions: {URL}. Is that all there is to it?
My management has tasked me to give them a high level overview of the different switching we can choose for our new building.
This is what I know so far.4 Closets, each closet has 450 ports,One MDF room that is will contain one UCS Chassis and a Nimble iSCSI SAN.
I am working on the spreadsheet and it looks like this (Not totally filled):
2960s3560x3750x45064510Approx cost (Each, 48PORT, POE+, 10G uplink, Dual PS, IP BASE)
6K7K8K45K75KMax Capacity192432432192384Backplane speed206464520520ProLeast ExpensiveStackable to 9Stackable to 9ProDual PSDual PSDual PSDual PSDual PSProLayer 3 opt
Layer 3 optDual SupsDual SupsConExpensiveExpensiveConNo Dual PSConLayer 2 OnlyCannot stack more than 4
For the MDF I would like to use 2 Nexus 5548's with FEX's, and the layer 3 daughter board. For the IDF's I was thinking of two 4010's.
upgrading our small office network. We currently have about 75 employees with probably 125 devices on the network. I'd like to create about 10 vlans for the different departments and then configure intervlan routing as needed. Currently we have all unmanaged switches and it's just a huge broadcast storm on the network. We are upgrading our Cisco 800 router to an ASA5505 sec. Plus license. I need some recommendations on switches. Of course, this needs to be done as cheap as possible.... Is there a way to use the ASA to configure all the vlans and intervlan routing and access lists and use a cheaper switch to provide the access layer to hosts?
View 4 Replies View RelatedI have the following config using a Cisco 1921. I am trying to get devices on the the native VLAN to get internet access via the gateway x.x.x.73.Any thing being routed from the other Vlans 15/20/30 can get access, but nothing from an internal IP address. Is there something I am missing.
The Xs replace the same 3 octets for each interface.I am trying to route from VLANs 15/20/30 to see VLAN 5. I have tried a few things, in terms of adding extra ip routes, but can't get anything to work. Each of those Vlans have another router on the other side of them, which I have also tried adding ip routes too, but nothing. One of the routers (Vlan15 is a Draytek 2830). [code]
I implemented access list on cisco 3560 switch but it never works. I want to block access from network B to Network A and allow from Ato B
Network A. 10.0.12.0/24
Network B 10.0.24.0/24
The configuration is
interface Vlan1
description Data VLAN
[Code].....
I have a cisco 871w router that I'm trying to incorporate into an existing network. I have FastEthernet4 (WAN port) plugged into an ISP device, which I don't have access to. I have the address set to use dhcp, which is successfully recognized and I see that the interface gets a valid ip address that I can ping with other computers on the same network.
Problems: I am logged into the router via the serial port and I cannot ping websites on the internet. I am able to ping sites that are hosted inside the WAN, but when I try "google.com" for instance, I see it sending out packets, but none are received. It resolves the hostname from the local DNS server, but there are no packets received.
I type into the console to set up the router. I'm missing a lot of stuff. This is what I've been able to piece together using google and the software manuals:
enable
config t
hostname [hostname]
interface FastEthernet 4
[Code].....
As soon as I add the interfaces of the router to security zones it significantly drops speed on WAN interface, below 1 Mbs. I noted this because I wasn't able to watch youtube. Moreover the bandwidth test from speedtest.net hangs and doesn't come to a result. Here below is the diagnostic example while doing that test. The question is what is going on? I have two iPhones and three computers in my network, that's it. My ISP bandwidth is 10 Mbs, so is this the router hardware limitations, or kind of malfunction or some misconfiguration down here? What could be done here ?
View 4 Replies View RelatedIs it possible to make Any Connect VPN from IPad/iPhone to 871w? IPSec VPN is working perfectly but cant get my Cisco AnyConnect iOS client to connect. I have config webvpn and it beeing user/pw prompted but keep getting the following error:
"the required license for this type of VPN client is not avaiable on the Secure gateway. Please contact Your network administrator".
