Cisco Wireless :: 871W In Universal Client Mode Bridging
Jul 21, 2008
I have a 1242 Access Point as root and a 871W Router as a non-root bridge (Diagram attached). I have a laptop connected to Fa 0 of the 871W router.
* I am able to ping from the AP to the Router and vice versa
* I am also able to ping from the router to the laptop and vice versa
* But I am not able to ping from the laptop to the AP
All bridging commands seem to be fine. Even tried adding route commands, but none seem to work.Please find the configuration below:
Configuration on Root AP:
hostname ap
!
enable secret 5 XX
!
[Code]....
View 4 Replies
ADVERTISEMENT
Aug 14, 2012
Is it possible to downgrade the 4900M IOS image from Universal 15.x image to non-Universal (possibly IP BASE) 12.x image.
View 1 Replies
View Related
Aug 21, 2012
Below is my VPN config in my 871 and radius user config. I am unable to connect to the vpn using Cisco vpn client. I am getting one of two errors depending on what config changes I make.I believe I have the radius configured correctly because it is authentication but not 100% sure.
[code]...
View 3 Replies
View Related
Feb 17, 2013
I realized that when I connect dir825 on bridging mode to my current voip router provided by my ISP (dvg-n5402) ,shareport does not work as it seems to be using the default gateway to find the usb, which in this case default gateway goes to the gateway of my voip router. Is there any way that I can make shareport use the gateway of my dir825 instead?
View 5 Replies
View Related
May 26, 2012
1) Apparently, my Cisco modem likes to assign new IP addresses to things, so I didn't figure out the web access page until an hour in (was NOT 192.168.1.245)
2) Do I input the same IP address, subnet, DNS and default gateway as my Cisco modem? It has a wireless router and switch bundled in, should I use the wireless network's MAC address or the wired?
Currently, it's set to 'automatically configure':
IPv4
Local IP Address: 192.xxx.x.xx
Subnet Mask: 255.xxx.xxx.x
Default Gateway: 192.xxx.x.x
Primary DNS: 64.xx.xxx.xxx
Secondary DNS: 0.0.0.0
I can access the page fine, but I cannot get the wireless client working...
3) I did a site survey and found my existing network and inputted its SSID and MAC address, but nothing happens. I still get one bar on my wireless devices indicating the AP isn't working.
View 1 Replies
View Related
Dec 7, 2009
I have purchased 4 of these devices about 2 months ago and have experienced all of the issues reported within this thread. The came with the 2.0.0.5 FW rev installed, so unless the 2.0.0.5 on the cisco DL site is different, nothing I can do with that.I've tried making them work as stand alone AP's, Bridge<-> Bridge, etc... all modes seem to lock up eventually needing a reboot to get any functionality back.Ultimately, I need to make them work in AP<->Client-Repeater mode. I've not been successful in making them work in any mode for a prolonged period of time.
having just rfound this thread today, I have not tried hard coding the NIC's to 100/full, but will give it a try. If it works, great, but then that would defeat the purpose of buying an N radio AP. I would like the potential 300Mbps throughput.
View 13 Replies
View Related
Jul 1, 2012
My house has 2 floors.In the first floor i have a wag160n connected to adsl internet.On the second floor i want to use my old wag120n to connect wirelessly to the router in the first floor and redistribute the internet through his ethernet ports(through wag120n ethernet ports).I want to do this because on the second floor where the tv is i want to connect a dreambox that has only ethernet connection so i can give internet to it via the wag's 120n ethernet ports.
View 2 Replies
View Related
Sep 5, 2011
What kind of hardware are people using for mobile bridges? I have not had good luck with Cisco 1242's in bridge mode with mobile-client enabled. The only reason we're using the Cisco access point over standard industrial bridges is because we need to manually forward the mac addresses of the devices behind the bridge. These are being installed on robotic forklifts. They have a generic ethernet scrolling marquee installed that does not maintain any active connections and drops from the fowarding table in the bridge if not staticly configured. I'm looking for an alternative because the roaming is not nearly as smooth as it should be.
View 3 Replies
View Related
Jan 2, 2013
I have a WISP internet connection. i have a Acess point tplink tl-wa5110g . i set it to wisp client router... My final goal is to share my wisp internet wirelesly.
Now i want to ask what i have to do next. do i need wireless router and connect it with the Ethernet port of the acess point..
View 1 Replies
View Related
May 7, 2013
Region : UnitedKingdom
Model : TL-WR702N
Hardware Version : V1
Firmware Version : 4.18.114 Build 130314 Rel.39604n
ISP :
I've setup my nano router in client mode and successfully connected it to my existing wireless network by manually setting it's IP address to 192.168.1.2. The existing router has the IP address 192.168.1.1.
I know this has worked as I'm able to access the web management page from any computer in the house by visiting the IP address 192.168.1.2. So far so good.
However, my problem is that the nano router cannot speak to the internet. If I login to the web management page and go to diagnostics, I can ping every other device on the network fine, but I can't ping anything outside the network (e.g. 8.8.8.8 or [URL].
I've tried in vain to get this setup correctly, all I can assume is that the nano router isn't correctly determining that the existing router (192.168.1.1) is where it should be routing all external requests and they're just getting lost, but there's no configuration for that on the web management pages.
View 12 Replies
View Related
Dec 19, 2011
I have replaced my main router WRT300N running dd-wrt with the a stock E4200 and an old WRT54G aslo running dd-wrt configured for wireless client bridge. Now that I'm learning more about 802.11N, I was wondering what client can I use to achieve 5ghz simultaneously radio transmission since my current setup cannot do this in the 5ghz band. Can the E3000 be ran in wireless client bridge mode, if not what product can provide this? On the other thought am I understanding MIMO?
Old setup: 802.11G 2.4ghz
WRT54G ))) ((( WRT300N ->ISP
Current Setup: 802.11N 2.4ghz MIMO?
WRT300N ))) ((( E4200 ->ISP
Wanted Setup: 802.11N 5ghz MIMO
( E4200 ->ISP)
View 3 Replies
View Related
Aug 16, 2012
I need an AP that can run in client bridge mode. By that I mean a device that can be connected to a PC via the ethernet cable and provide wireless access because these older devices don't have wireless network cards?I looked at the WAP321 but it just uses a wizard. I need a device with IOS so that the PSK keys can be encrypted when viewing. I need to have the config backed up and the PSK can't be in clear text.
View 5 Replies
View Related
Jul 5, 2011
Who knows the best version (DD-WRT or other) to repeat the wireless signal with a E3000?At worst, a client bridge mode could be sufficient for my needs...
View 9 Replies
View Related
Dec 4, 2012
Region : UnitedStates
Model : TL-WR700N
Hardware Version : V1
Firmware Version :
ISP :
My TL-WR700N does its job to provide wired internet to my desktop computer from another wireless router via client mode. However, when it is connected, the other wireless clients connected to the primary router lose their connections. To restore those connections, the WR700N must be powered down and the primary router must be restarted.
View 4 Replies
View Related
Dec 6, 2012
Region : Argentina
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
Region : UnitedKingdom
Model : TL-WR740N
Hardware Version : V1
Firmware Version :
ISP :
Am trying to use a TP-Link TL-WR702N to connect my Samsung SmartTV to a wireless network, using "client mode".For some reason, the TV refuses to accept it is connected, or even connected to a router. Enabling DHCP on the TP-Link does seem to convince the TV that it is connected to a router, but still not to the internet. Strangely though, I can control the TV via the Android app operating on the local network, so clearly it is connected. I assume the SmartTV is trying to get a response on the local network that the TP-Link is filtering out for some reason, but no idea why.
View 14 Replies
View Related
Apr 21, 2013
Does Cisco CleanAir 1602i (standalone model) support Universal Workgroup Bridge? I read the release notes 15.2 but I couldn't find it.
View 7 Replies
View Related
Oct 10, 2011
Contrary to the information contained in the link above, these two parts do not play well together. I purchased both and plugged them in and no go. It doesn't even light anything on the WAP. It worked fine when it was on its own 12V DC adapter but not plugged into this injector. What I don't understand is why Cisco doesn't just make a Universal power injector that is essentially a 1 port switch and is 802.3af or 802.3at compatible. Its maddening. It looks like I'm going to have to get an SD208P and waste 6 ports just to get one with the correct POE for the WAP4410.
View 2 Replies
View Related
Dec 11, 2012
Could not find on Belkin website, hyperlink came up with "oops' result. Basic instructions to hook this up to my TV.
View 1 Replies
View Related
Nov 16, 2011
Is there a client mode option for the DIR-655?I just got a nice cable modem/router from my ISP and I'd like to re-purpose my DIR-655.If I could turn a usb webcam, printer, or harddrive into wireless client, that would be cool. I would just rather re-purpose the device versus selling it.
View 2 Replies
View Related
Aug 9, 2011
I bought an 871w second hand with 124-24T IOS on it. I would like to enable QoS. When I use Cisco Configuration Professional to manage the router I click on QoS and it says it is not available. I know that the router itself is QoS capable.
This is my first time dealing with a router such as this and I wonder what I need to do to enable QoS.
View 1 Replies
View Related
Apr 15, 2012
Whatever a NAT is supported for ACE-20 module? I do need to convert working CSM(SLB) config to ACE configuration and I am not quite sure if the configuration below is correct. ACE module should be configured in bridge mode with two vlans - vlan 36 (client) and vlan 436 (server) - bridged with interface bvi 36. NAT on ACE configurad as "nat dynamic 1025 vlan 436" into corresponding "policy-map type loadbalance". Check two parts of configs and if the ACE config is properly converted from CSM and will be working in the same way (especialy for NAT). [code]
View 2 Replies
View Related
Feb 28, 2011
I'm trying to connect a non-wireless enabled pc to my virginmedia network by using a tp-link ta-wa500g router in client mode. The pc connects to the router via ethernet fine, and i can access the router admin page etc., but the router doesn't seem talk wirelessly to the virgin box. it finds it and everything, but i can't access the internet at all. i've tried removing the password, resetting everything, I've upgraded to the latest firmware, but have come to a bit of a dead end.
View 1 Replies
View Related
Sep 20, 2011
About twice a day (that I notice) my wireless loses its internet connection. All the wired machines continue to be connected to the internet but any wireless ones lose internet, though they maintain a connection with the router.
View 7 Replies
View Related
Sep 23, 2012
I have a small wireless network, which consists of three AP1121G with c1100-k9w7-mx.123-8.JEB1 ios and one 871w with c870-advipservicesk9-mz.124-24.T1. I've configured two different ssid's with individual authorisation types - ssid_1 with eap, ssid_2 with wpa. All three ap's works as it should be, but 871w authorises only eap connections, and all other types are rejected
View 3 Replies
View Related
May 12, 2013
I'm trying to configure WiFi on my Cisco 871w router withouth any knowledge in this area. And it's a tough one, couldn't do it just with google, hope this is the place where I can get it done right step by step if possible. Everything else works fine. I'm going to post my messy show run below. Everything I did on dot11Radio will need to be cleared I suppose.
Point38#show run
Building configuration...
Current configuration : 4072 bytes
!
! Last configuration change at 16:23:18 UTC Thu Sep 8 2011
version 15.1
no service pad
[code]...
View 3 Replies
View Related
Nov 5, 2012
I have a problem with myself a few other clients randomly disconnecting from my 871W. It appears that I am still associated but Windows 7 shows "Limited Access". I appear to be assosciated to the AP and I still have my ip address but I can't ping the 192.168.1.1 gateway (871W). I have also set my power plan to allow for Maximum Performance which I thought disabled PSP but the log is still showing errors.As a final note, after I reconnected by ip address (192.168.1.107) doesn't show up in "sh ip dhcp bindings" but I'm working.To correct the situation, I have to disconnect and the reconnect to the AP and then I am good for another day or close to it. Below are the log errors, config and a sh ver. [code]
View 7 Replies
View Related
Apr 16, 2012
I have a Cisco 871W that periodically will drop its signal. how to configure this for maximum reliability? I set it to use chanel 2462.
View 1 Replies
View Related
Jan 27, 2009
I know this question was asked many times, but I'm still not able to finalize my configuration on 871w. LAN part works fine, but wireless clients do not get DHCP IP. here is the config:
Building configuration...
Current configuration : 2092 bytes
!
version 12.4
no service pad
service timestamps debug date time m sec
service timestamps log date time m sec
no service password-encryption
!
[ code ].....
I'd like to have LAN and WLAN clients in same 192.168.1.0 sub net.
View 3 Replies
View Related
Mar 25, 2012
My current production network is setup using VTP in Client mode, and I am looking to enable VTP Transparent so I can enable the extended VLANs. My main question would be, would enabling VTP Transparent on my 6509 affect all of the access switches it is connected to? And if so, would changing all of the access switches to VTP Transparent allow them to regain connectivity quickly with little downtime? Or is there another way that I should be handling this situation to enable the extended VLANs?
View 2 Replies
View Related
Mar 14, 2011
Okay so for the past week i have battled with my two routers trying to make them talk to each otherMy main router (router A) is a dlink dir-615 ver. BMy second router (router b) that im trying to make talk to router A is a dlink router dir-615 ver E1 flashed with dd-wrt custom firmware.I have looked at every setup guide people have posted online and youtube videos to no avail
View 6 Replies
View Related
Mar 14, 2013
I've been trying to get my wireless configured for the past few days with no luck. I can ping every device on my local network and I can ping outside my network and surf the web. My wireless devices can see my wireless network but cannot connect to it.
[code]....
View 1 Replies
View Related
Mar 21, 2013
I have a setup with a were I configured monitor mode on a switch with ISE as RADIUS server. This is for testing before a bigger deployment at a customer site.Im using ISE 1.1.3, C2960 and IOS 15.0(2) and a laptop with Windows 7 Enterprise SP1. The correct configuration with EAP-TLS and machin cert is working like it should but it is when I remove this and make the laptop fail that I get wierd results with monitor mode. I cant get DNS to work in dot1x monitor mode if the client fail authentication.
When the client fail dot1x and MAB it gets a IP with DHCP. I can ping but DNS/browsing is not working. If I put the AuthC back and the client authenticates DNS is working, or if I turn of dot1x on the client then DNS work as it should. [code]
View 3 Replies
View Related
Jan 14, 2013
I'm working at a company that has several 6509 switches running CatOS. They have two of the 6509's running in vtp server mode and the rest as clients. I set up a new vlan from one of the vtp servers and it propagated out. The problem comes when I try to assign a port on one of the vtp clients to this new vlan. It gives me an error that the switch must be in vtp server mode to add/delete vlans. I'm not trying to add/or delete a vlan just trying to add a port into an existing vlan. I'm hesitant to put the switch in vtp server mode. Is this a CatOS thing or is there a specific command to accomplish this?
View 5 Replies
View Related
