Below is my VPN config in my 871 and radius user config. I am unable to connect to the vpn using Cisco vpn client. I am getting one of two errors depending on what config changes I make.I believe I have the radius configured correctly because it is authentication but not 100% sure.
[code]...
I have a 1242 Access Point as root and a 871W Router as a non-root bridge (Diagram attached). I have a laptop connected to Fa 0 of the 871W router.
* I am able to ping from the AP to the Router and vice versa
* I am also able to ping from the router to the laptop and vice versa
* But I am not able to ping from the laptop to the AP
All bridging commands seem to be fine. Even tried adding route commands, but none seem to work.Please find the configuration below:
Configuration on Root AP:
hostname ap
!
enable secret 5 XX
!
[Code]....
I'm unable to maintain a connection with an FTP host outside my network through my Cisco 871W Wireless/Wired router. I am able to establish a connection with the external FTP server, but when I attempt to transmit files I get repeated disconnections and failures.
The software running on the device is IOS C870-ADVSECURITYK9-M, Version 12.3(8)YI2 RELEASE SOFTWARE (fc1)
Synched to technology version 12.3(10.3)T2
System Bootstrap Version 12.3(8r)YI
I know it has to be somewhere in the configuration, but SDM no longer operates and I'm not entirely familiar with the IOS command set. When I remove the Cisco device and plug my computer directly into my ISP network, I am able to send files via FTP with no problems.
I have an 871 set up at home with 2 VLANs, both of these vlans present a strange behavior where an user is unable to ping/contact another user on the same subnet, however if users are on different subnet it seems to work [code]
According to the troubleshooting that I have done, the issue seems to be with the broadcast traffic, ARP request/reply do not reach another host on the same subnet (wireless to wireless or wired to wireless) however if the wireless device iniciates the connection to wired, it works fine.
I have tried to enable proxy arp on the different VLANs and BVI and different combinations but no sucess in order to get traffic across 2 wireless devices on the same subnet or a connection that is iniciated for a wired client to a wireless one.
I tried enabling and disabling dot11 arp-cache but no luck.
We have a cisco asa 5505 on which we have setup a group VPN. The VPN connections from all cisco vpn clients works fine except one. The keep getting the below error
"Secure VPN Connection terminated locally by the client. Reason 412: The remote peer is no longer responding. Connection Terminated".
Not sure why only one client won't be able to connect. The version we are using is 5.0.02 for VPN client.
we have ASA5510 with version 7.x and asdm 5.X, i upgraded it to 8.3 and asdm 6.2, and i got vpn peers 250 and 2 ssl.when i try to connect through client software , i can see in the logs UDP 500 port is created as shown below. [code]
and currently in right panel of Active Algorithms i have only RC4-SHA1,
Is it possible to make Any Connect VPN from IPad/iPhone to 871w? IPSec VPN is working perfectly but cant get my Cisco AnyConnect iOS client to connect. I have config webvpn and it beeing user/pw prompted but keep getting the following error:
"the required license for this type of VPN client is not avaiable on the Secure gateway. Please contact Your network administrator".
i have a question about tunneling a software EasyVPN client to a client ASA Network. It looks like this:
EasyVPN Server 192.168.202.0/24 Network extension mode to Client EasyVPN ASA 192.168.1.0/24 This works fine in both directions. But now i want to connect the client ASA network via EasyVPN software client from outside. The user are already able to connect to the ASA Server on its static outside IP obtaining an IP from a 192.168.21.0/24 pool. This works fine. But how am i able to connect to the 192.168.1.0/24 network from this client?
I have configured VPN client on my ASA 5510,
I am trying now to telnet my call manager on port 5060 and on port 2000.
When i am connected localy i am able to telnet both ports, but when i am trying to connect through cisco VPN client i am able to telnet the port 2000 and not able to telnet 5060. Both ports are on the same call manager.
When using windows VPN i am able to telnet both ports.
if i removed inspect SIP from: policy-map global_policy class inspection_default
I'm using LMS 4.0.1 and VPN hw client 3002 with software 4.7.2.L.I'm not able to collect the first configuration and sync jobs end with these errors.
View 2 Replies View RelatedOn my Windows 7 laptop, after connecting to my office Network using Cisco VPN clientThe entire Internet is utilized by the VPN. I am unable to browse the internet on my computer till I disconnect the VPN Client.
View 3 Replies View RelatedHaving an issue with the ipsec client being unable to add routes in Windows 7 while connecting to an asa 5510 running 8.3(2). Client connects, but the split-tunnel routes do not get installed on the OS. Vpn client versions used are 5.0.07.0290 and 5.0.07.0440 x64. The client status window shows that it received the split tunnel networks, but the log shows that the routes do not get installed with the following message:
Sev=Warning/2 CVPND/0xE3400013
AddRoute failed to add a route with metric of 100: code 87
Destiantion 192.168.100.0
Netmask 255.255.252.0
Gateway 0.30.1.1
Interface 10.30.1.201
[code].....
Very recently, we had implemented Site-to-Site VPN tunnel between two Linksys RV042 4-port VPN routers. Everybody in our remote site is accessing and sharing the data through this tunnel and it is working fine.
Now, we have a plan to implement the same for our mobile clients also. For this, we had followed all the basic configuration procedures and user got connected to Quick VPN tunnel. Here is a problem we had observed. The mobile client user is connected to the tunnel, but unable to access the office LAN from the PC.
I have access to network 10.3.1.0 /24 but I am not able to access 10.3.2.0/24 and other networks behind the Easy VPN server.I am using a software client to connect to the server.I have configured split tunnel to the network 10.3.0.0 /16 and it shows up in the route details too. I can ping 10.3.1.0 network but not 10.3.2.0 and so on.The Easy VPN server is configured on Cisco 861 with VPN module. [code]
View 6 Replies View RelatedI have a VPN setup thru a Cisco 5520, Windows clients connect just find and the end users configure there browser to use our internal proxy servers. Users with the MAC OS X Anyconnect client can connect, they configure their Mac to use our proxy server, but the broswers will not work, clients can reach networks and resources behind the VPN gateway and have access to the Proxy(Tried a telnet to that hostname/port). I am running ASA 8.3(2), Anyconnect(OS X) 3.1.01065.
View 3 Replies View RelatedI have an ASA 5510 running v8.4(3)9 and have setup a remote user VPN using the Cisco VPN client v5.0.07.0410 which is working appart from the fact that I cannot access resources on a secondary subnet.The setup is as follows:
-ASA inside interface on 192.168.10.240
-VPN clients on 192.168.254.x
I can access reources on the 192.168.10 subnet but not any other subnets internally, I need to specifically allow access to the 192.168.20 subnet,[code]
I recently purchased a Cisco 2911 to replace my Cisco 1711 router. I copied the configuration from the Cisco 1711 router to the Cisco 2911 router. Everything seemed to work correctly except when I VPN tunnel into the Cisco 2911 router using Cisco's VPN client version 5.0. I can ping the router LAN interface from my PC that is VPNed into the router but I can no longer ping or access the devices on the LAN side of the router as I did on the Cisco 1711 router. I don’t see errors in the log or hits blocking anything in the acls. It’s using the same configuration that I had on the Cisco 1711 router, and this did work on the Cisco 1711. The Cisco 2911 router is running IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.0(1)M1, RELEASE SOFTWARE (fc1).
Here is the VPN clinet portion of the configuration: The LAN is addressed as 192.168.0.0/24. The router LAN interface is 192.168.0.1, which I can ping and access. I can't ping or access anything on the LAN (192.168.0.0/24) beside the router.
aaa authentication login vpnclientauth local
aaa authorization network vpngroupauth local
!
crypto isakmp client configuration group remote-clients
key 6 xxxx
pool clients
[Code]....
Background: Wireless credit card machines can't stay connected to the 5508 controller 7.0.116 / 1142 ap wireless system. MAC address of one of the wireless hosts is 00:12:0e:ec:ce:97. AP servicing them is d4:a0:2a:99:34:60. Hosts are able to connect to the network after a reboot and stay connected for random periods of time but then don't come back unless you manually reload them. I have 3 in total in the same room services by the same ap.
I have the output of debug client 00:12:0e:ec:ce:97. Output showed 802.1x 'timeoutEvt' Timer expired for station 00:12:0e:ec:ce:97 so I increased the value to 4000ms on the controller but am still having the issue.
Note that the output below is the state the client stays in after receiving the timeout (802.1x 'timeoutEvt') showing subsequent attampts. The only way to get them back on is a reload of the credit card machine.
[Code]........
I am a bit green with IOS and have exhausted everything I can think of with this. The router passes the WAN test in CCP?Undoubtedly there are probably a few things in the config that are either redundant or totally unnecessary, but I have been trying a few things to solve this with very little success.I have no security stuff in here because I have triewd to keep the config as simple as possible to start with. I will add that after I get the routing working.
Here is my most recent config:
Cisco871W#show config
Using 2631 out of 131072 bytes
!
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[codde].....
I recently setup a 2504 WLC that has two primary WLANs (internal and guest) which get their IP addresses from a central DHCP server using the local router's broadcast forwarding. Things seem to be working well for the internal wlan, but clients on the guest wlan don't seem to be getting IP addresses. If I give the client a static IP they are able to communicate across the wlan okay.
It is worth noting that I am using LAG between the controller and router and this guest wlan is really just a regular wlan (with PSK) that has an access-list applied to force it to the internet only. The access-list should be allowing dhcp requests through, but in any case, I removed the access-list and it made no difference.
Here is a debug client for a machine connected to the guest vlan (vlan 33). The internal wlan is on the 10.10.10.0/24 network (same as wired and same that the AP's are connected to) and the guest wlan is 10.33.0.0/16. I don't understand why I am seeing the dhcp request come from the internal vlan/ wlan first and it gets an IP address on this network. I then see a request on the guest wlan/vlan at which point it appears to get a valid IP address on the guest network (10.33.0.0), but the client never sees this. [code]
I have a Cisco 881 setup with the following VPN config.
[code]...
The client is able to connect just fine to the network via VPN, but I am unable to gain access to any of the local resources. I know 192.168.1.1 has SSH running and 192.168.1.50 has telnet running but if I try to connect to either using the correct program they just timeout. I am really at a loss on why the vpn connection connects but I can not gain access to any of the resources on the VPN network.
I bought an 871w second hand with 124-24T IOS on it. I would like to enable QoS. When I use Cisco Configuration Professional to manage the router I click on QoS and it says it is not available. I know that the router itself is QoS capable.
This is my first time dealing with a router such as this and I wonder what I need to do to enable QoS.
I want to upgrade my IOS on an 871W. In order to do this I need to upgrade the memory. I have found that I need the MEM870-32F (Am I correct?).
As in here: {URL}. So if I follow these instructions: {URL}. Is that all there is to it?
I have created a VPN connection for ASA 5512-X by using the wizards and nothing seems to be wrong on the wizards's config.I am able to connect to the network by using the VPN but unable to ping internal network.Below is my config for your reference:
Result of the command: "sh run"
: Saved
:
ASA Version 8.6(1)2
!
hostname FAA-ASA-1
enable password crzcsirI44h2BHoz encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
[code].....
I have a Cisco 871 router at one of my client sites.(they purchased the router from me and I sent them the router with a basic configuration on it). When they connect it after hours clients get the proper IP addresses and dhcp configuration however are unable to access the internet.We are connecting their ISP supplied router to Gigabitethernet0. They have a static address. I have been through the confirmation many times and am thinking I am missing something so simple.
View 2 Replies View RelatedI have a cisco 871w router that I'm trying to incorporate into an existing network. I have FastEthernet4 (WAN port) plugged into an ISP device, which I don't have access to. I have the address set to use dhcp, which is successfully recognized and I see that the interface gets a valid ip address that I can ping with other computers on the same network.
Problems: I am logged into the router via the serial port and I cannot ping websites on the internet. I am able to ping sites that are hosted inside the WAN, but when I try "google.com" for instance, I see it sending out packets, but none are received. It resolves the hostname from the local DNS server, but there are no packets received.
I type into the console to set up the router. I'm missing a lot of stuff. This is what I've been able to piece together using google and the software manuals:
enable
config t
hostname [hostname]
interface FastEthernet 4
[Code].....
As soon as I add the interfaces of the router to security zones it significantly drops speed on WAN interface, below 1 Mbs. I noted this because I wasn't able to watch youtube. Moreover the bandwidth test from speedtest.net hangs and doesn't come to a result. Here below is the diagnostic example while doing that test. The question is what is going on? I have two iPhones and three computers in my network, that's it. My ISP bandwidth is 10 Mbs, so is this the router hardware limitations, or kind of malfunction or some misconfiguration down here? What could be done here ?
View 4 Replies View RelatedAbout twice a day (that I notice) my wireless loses its internet connection. All the wired machines continue to be connected to the internet but any wireless ones lose internet, though they maintain a connection with the router.
View 7 Replies View RelatedI have a small wireless network, which consists of three AP1121G with c1100-k9w7-mx.123-8.JEB1 ios and one 871w with c870-advipservicesk9-mz.124-24.T1. I've configured two different ssid's with individual authorisation types - ssid_1 with eap, ssid_2 with wpa. All three ap's works as it should be, but 871w authorises only eap connections, and all other types are rejected
View 3 Replies View RelatedI am new to Cisco and am studying for my CCENT certification. At the moment, I am attempting to correctly configure a Cisco 871W lab router. Since I have undertaken this task, I have run into nothing but problems. First off it was finding that the previous owner had left a password on it, having to purchase a new USB to DB9 adapter to pass the "break" sequence to the router, and then resetting the router in ROM Monitor mode.
Now, I cannot seem to configure the router correctly, and am quite stumped.
My ISP is Charter (cable internet), and the home network that I am using consists of a Motorola SBV5122 Digital Voice Modem, Motorola SB6120 Cable modem, and, ideally, should also include my Cisco 871W router.
When I connect my router to the SB6120 Cable modem, the router receives an IP address via DHCP and the WAN indicator light turns on.
I have a VLAN configured on the 4 switchports of the router, and it is setep to act as a DHCP server. However, when I connect my PC to rhe router via Cat5e Crossover cable, I cannot access the internet. The router gives the PC an IP address, yet all attempts to ping the PC from the router fail. Somehow, I can connect to the router via SSH though.
Furthermore, I can ping the 127.0.0.1 loopback address from my PC, but cannot do so from the router.
how to correctly configure this router to function as intended in my network situation, however, this is proving to be seemingly unsurmountable!
I have attached the config of my router along with both outputs and commands relating to my predicament.
I'm trying to configure WiFi on my Cisco 871w router withouth any knowledge in this area. And it's a tough one, couldn't do it just with google, hope this is the place where I can get it done right step by step if possible. Everything else works fine. I'm going to post my messy show run below. Everything I did on dot11Radio will need to be cleared I suppose.
Point38#show run
Building configuration...
Current configuration : 4072 bytes
!
! Last configuration change at 16:23:18 UTC Thu Sep 8 2011
version 15.1
no service pad
[code]...
I've acquired an 871W, because I'd like to use wireless, to replace my 851. I Ft Pd the 851's configuration to my FTP server and then Ft Pd this to the 871W. Save for the fact that this has a radio interface (currently shutdown), everything works save for FTP from the outside. I can not even telnet to port 21 of any of the internal FT servers. I can telnet to any other port (ssg, smtp, HTTP, https, etc.) but FTP will not pass. What's the difference?
View 12 Replies View RelatedWe find ourselves in a difficult situation with the Cisco VPN Client version 5.0.07.0290 where it keeps giving us an
"Error 42: Unable to create certificate enrollment request"
When we attempt to use the Online enrollment method to create and enroll a new certificate. There is no additional information in the VPN client logs where we have set 3-High for all logs. In addition, Wire shark does not show any packets sent from the machine running the client to the Cisco 3825 router which runs the Cisco CA.
To create and enroll a certificate we do the following:
1. Click on the Enroll button to show the Certificate Enrollment dialog
2. Select Online
3. Select <New> for Certificate Authority
4. Enter http://192.168.120.1 as CA URL (note, 192.168.120.1 is the IP of the Cisco 3825)
5. Click Next to display the dialog where we can enter certificate details
6. Enter details in all fields except IP Address and Domain
7. Click Enroll which shows a dialog with the Error 42 ... message in it.
If we attempt to create a request by using the File method, all works fine, that is, the client creates a file with the enrollment request. The fact that the client does not send any messages to the Cisco CA leads us to believe that we have a problem on the client machine. However, the client does not write any information in the logs, so it is a bit hard to fix the problem. I can provide additional configuration information if required for both the client and the Cisco CA. Note that we have not modified any client configuration. Basically, we installed the client on a Windows 7 64bit machine and attempted the steps listed above.
