Cisco Routers :: Unable To Access LAN Behind RV042 From Quick VPN Client?
Aug 22, 2011
Very recently, we had implemented Site-to-Site VPN tunnel between two Linksys RV042 4-port VPN routers. Everybody in our remote site is accessing and sharing the data through this tunnel and it is working fine.
Now, we have a plan to implement the same for our mobile clients also. For this, we had followed all the basic configuration procedures and user got connected to Quick VPN tunnel. Here is a problem we had observed. The mobile client user is connected to the tunnel, but unable to access the office LAN from the PC.
View 1 Replies
ADVERTISEMENT
Nov 26, 2011
I have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies
View Related
Apr 7, 2012
PID VID : RV042 V03
LAN IPv4/ Subnet mask : 192.168.0.7/255.255.255.0
Working Mode : Router
[code]...
PPTP working fine but not with Quick VPN .. test on some computer and internet access still can not get connect to router.
View 79 Replies
View Related
Mar 3, 2011
we bought a router for our company RV042, so far good
What i did:
1. i created QuickVPN clients, droped in certificate which exported from router
******NOTE********All company's laptops are running: Windows 7pro 32bits****************
The users are connecting sucesefully to router and using resources from server etc...
But, when they press disconnect on quickVPN it shows disconnected, but when i log in into router, i still see that they are connected (not disconnecting),
and the problem is they cannot connect to router second time if i don't manually disconnect them from rv042 router....
Only sometimes the clients disconnect properly from router, but it is very very rare...
Question1: Where I should look for the problem in router rv042 or client laptops?
Question2: Does the 64bit windows7 pro OS can connect to RV042router?
I have latest quickvpn software and latest router firmware.
View 10 Replies
View Related
Oct 6, 2011
Quick VPN and have not had any success connecting with our router. Below is my components info. Cisco router: WRVS4400N, Firmware V2.0.0.7. The router is behind a Comcast SMC business gateway modem Remote computer: Window 7 Ultimate 64 bit
I downloaded the Quick VPN client 1.4.2.1, and installed the client successfully but cannot connect using the VPN Client Account that I had set up in the router. Below are several questions that I hope to understand.
1) Do I need to configure specific ports for VPN in the Comcast gateway firewall?
2) What IP address do I put in the Quick VPN client profile when I connect remotely? The WRVS4400N modem shows 2 IP addresses in the Status:
DNS1: 68.xx.xx.176
DNS2: 68.xx.xx.132
Are these the IP that go into the "Server Address" on the Quick VPN client profile? and which one of the two? or do I use the static WAN IP address provided by my Comcast account?
3) In the Quick VPN client window, what is the "Use Remote DNS Server" mean?
4) Do I need to create a client certificate from the WRVS4400N for the client
5) Is there any setup needed for the remote firewall (if the client is behind a home wireless router and modem, for example)?
View 3 Replies
View Related
Mar 14, 2012
I have a RV042 and have set it up for VPN Client access using the QuickVPN client to connect my remote users. I discovered today that I cannot have two users connect in at the same time. Both users are in the same remote office. They can connect individually with no problem but if one is connected and the other tries connect also the second user gets a message the gateway is not responding. They are both running Win XP PRo SP3.
View 1 Replies
View Related
Mar 15, 2012
I have a RV042 and have set it up for VPN Client access using the QuickVPN client to connect my remote users. I discovered today that I cannot have two users connect in at the same time. Both users are in the same remote office. They can connect individually with no problem but if one is connected and the other tries connect also the second user gets a message the gateway is not responding. They are both running WinXPPRo SP3.
View 4 Replies
View Related
Aug 29, 2011
I set up an RV042 as a VPN gateway for a client a year ago. It is running firmware 1.3.12.19-tm (Feb 13 2009 13:03:21). I created a new certificate. When I download the client certificate, It comes as a .zip file. One the can not be opened by a zip utlity (windows, Winzip or 7 zip). It looks like I can just rename the file to a .pem file, but I want to make sure that is right. They were getting QuickVPN timeouts, but that looks like it was fixed in 1.3.13.
View 3 Replies
View Related
Nov 15, 2011
I have a RV042 router setup with Client to gateway VPN access, and am connecting with a W7 PC running QuickVPN. We have many PC's that already have the standard CiscoVPN client on them, is it possible to configure the RV042 to allow these clients to conenct? I'm not sure how to get the Mutual authentication to work, or how to import the PEM certificiate into that client. It seems to allow it to import, but I can never select it.
View 2 Replies
View Related
Jun 9, 2012
I'm trying to set up a RV042 to do the following:
1) Block all WAN connections, except for:
2) Allow all port 80 connections, and forward to 10.4.20.60
3) Allow all port 443 connections, and forward to 10.4.20.60
4) Allow port 22 connections from specific IP addresses, and forward to 10.4.20.60
5) After a remote client has connected using Client to Gateway VPN, allow that remote client to access anything on the LAN
I'm able to do #1-4 above, but I can't get #5 to work. Or I can get #5 to work, but can't implement the restrictions I need in #1-4. Attached are some relevant screenshots. I think the problem is that I have Forwarding rules set up that require me to have a firewall rule to Deny All Traffic from WAN1 (unless I'm specifically allowing it). In the Access Rules screenshot, rule #6 is the problem. If I enable it (thereby denying all WAN1 traffic), then VPN clinents can't access anything on the LAN. However if disable this rule, VPN clinents can access anything on the LAN, but the firewall also opens up all outside connections to SSH, since that's set up in the Forwarding rules. I would have thought that once a remote client is connected using client to gateway VPN, then that client is considered to be on the LAN, as far as the firewall is concerned. Thus a firewall rule (like #6) that is specified for WAN1 shouldn't effect remote VPN clients.
View 1 Replies
View Related
Jun 15, 2012
Will the RV042 work with theAnyConnect Secure Mobility Client app? If so, is there and app note available? If not, which routers wil work with this app?
View 5 Replies
View Related
Jan 27, 2012
I am setting up remote access using an RV042 router. Using quickvpn or a client-to gateway vpn and shrewsoft client, I can only access/ping the LAN side of the remote router and one machine on the remote network. The PPTP server and native Windows 7 connection provide access to all machines on the remote network.I have 2 possible reasons for this and would like to find the real reason:
1) The remote RV042 is behind another router, and that router restricts access other than the PPTP traffic.
2) The VPN tunnels other than PPTP only allow access to the remote LAN side of the router and remote machines that have the remote router defined as their gateway in the IP configuration.
View 2 Replies
View Related
Nov 11, 2010
Any working configuration to connect the iPad VPN-client (IPSEC) to the RV042?
View 16 Replies
View Related
Apr 12, 2011
We recently upgraded from a Linksys WRT54G router to a Cisco RV042 to gain "gateway-to-gateway" automated VPN access. However, we are unable to get "client to gateway" access working.
With the Linksys WRT54G we used a "username" "password" pair for remote client authenication. This worked for both Windows and Mac OS X users using the built-in PPTP client. We found we had to set "encryption" value to "none" on the client side.
I am confused by the setup screens on the RV042. It looks like I must setup a "tunnel" (VPN->Client to Gateway), there is (VPN->VPN Client Access) where I can enter a username/password, and also (VPN->PPTP Server) where another username/password pair can be entered. I have tried all sorts of combinations but "no love". I am particularly mystified by the (VPN->Client to Gateway) settings for "Remote Client Setup"; the client can be calling in from anywhere and there is an option for "Dynamic IP + Email Address" but I'm not sure how that maps onto the client (do they use the email address as their account name?). I have also looked at defining a "Group VPN" where I am given other options. But nothing works from the client.
I just need to come up with some setup that works, that I can document to both PC and Mac users at a miniumum.
View 1 Replies
View Related
Aug 28, 2011
I have a RV042 router (Ser#: NKS10462300, HW V3) running Firmware version v4.0.2.08-tm (Jan 14 2011 22:08:38) set up as a gateway. Right after it boots I am able to long into its web interface but shortly after that if I try to log into it I go through a very log time out while the web page is waiting the router to respond and then eventually IE comes back and says it 'cannot display the web [age'.
View 30 Replies
View Related
Aug 29, 2011
I have an RV042 setup for quick vpn access.The remote computer in question is a win 7 64bit. The PC uses McAfee SAAS firewall. This disables the windows firewall.
1. I can connect to the vpn with SAAS disabled and windows firewall enabled.
2. I cannot connect to the vpn with both windows firewall and SAAS disabled.
3. I cannot run SAAS and windows firewall together to check if this would work.
I need to figure out what windows firewall is doing to allow the vpn to connect, and so how do this with windows firewall disabled. I can then leave the windows firewall disabled and enable McAfee SAAS.The message quickvpn provides when it fails to connect is that the remote gateway is not responding. The client logs show that the tunnel had been opened but it was unable to ping.
View 2 Replies
View Related
Feb 25, 2013
We have a Cisco RV042 Router. Two ISP's and using dual wan setup. We are trying to connect to a pc on our network using rdp. The pc we are trying to connect to has been configured to listed for rdp on port 3390. I have tested it internally and connect via rdp thru said port.
I have setup a port forward rule on the router to forward port 3390 to the ip of the pc. I have setup protocol binding for port 3390 service on wan1.
View 4 Replies
View Related
Jul 18, 2011
Im able to create a gateway tunnel with two rv042 routers in different locations ( i can see the tunnel connected in the router) but the quick vpn utility is not working , i also tried to use the pptp as server as an alternative( im able to connect using windows connection to the pptp server but whenever I browse any of the four ip's allowed for the pptp server \10.0.0.200-204 it takes me to the documents of the local computer....I attached the configuration for one of the routers it is the same as the other end , just the information is flipped.
Message was edited by: Adrian Torres
View 7 Replies
View Related
Jan 29, 2011
For the life of me I can’t get my quick VPN client to connect to my Cisco 120w. I have IPSec gateway to gateway setup and working just fine. I made my quick vpn client under vpn tab. I enabled remote management. Every time I try to connect I get the failed to establish connection. Using the same quick VPN software I can connect to a rv082 with no trouble.
View 2 Replies
View Related
Aug 6, 2012
I'm having issues getting QuickVPN to connect. I think it's an issue pinging the gateway but I'm not 100% sure. We are using Comcast Business, I have placed the RV180 in the DMZ. The setup looks like this: Internet -> Comcast router -> RV180 (DHCP) -> rest of network.
View 5 Replies
View Related
Nov 1, 2011
we recently bought a new desktop firewall solution from McAfee and I can't seem to get our VPN to work. I allowed QuickVPN in the firewall and additionally opened port 1194, 1720 and 1723 - but that does not do the trick. Once I turn off the firewall and use Windows Firewall instead it works.
View 2 Replies
View Related
Jan 12, 2011
I have been trying to resolve this issue with only allow facebook access throug the content filter between 12pm and 1 pm. However The settings never seem to take. Is this a bug in the system? If I start the filtering from 1300 to 1200 that should allow facebook to be accessible only on lunch.
View 2 Replies
View Related
Jun 20, 2011
I am trying to access my RV042 through telnet. I go to http://192.168.1.1/sysinfo123.htm?ConsoleSimulation=1
which enables telnet. However when I type my username and password it will not authenticate.
View 16 Replies
View Related
Jul 9, 2012
I am new to implementing VPN service. What I would like to do is install a RV042 or RV082 (for added speed) and configure it to allow me to access the Internet (from home base) through the VPN from any location while on the road and using my laptop. My questions are: Can this be done? If so, what needs to be done in the configuration to allow gateway access to the Internet? I can't find any reference in the Cicso documents, but somewhere I saw that it can be done. I don't care about accessing anything on the local LAN. As I would be using the same Internet connection for the VPN and the access to get out----how would this affect speed? I plan to use Quick VPN as the client, and haven't even touched the client issue.
View 5 Replies
View Related
Jun 8, 2012
I had this problem where 2 users could only access my RV042 vpn one at a time
The Linksys solution was to give these 2 users a RV042 as well. That worked, 2 can access my vpn at the same time. We use QuickVPN for this purpose
But now there users cannot access another Cisco vpn any more in our office. I attach a schematic and a screen shot of the error when trying to connect to the professional vpn with vpn client version 5.0.07.290
The 2 notebooks epresent the 2 users
The one at the bottom is my vpn
The connection on the left is the professional vpn
We now use remote desktop to my vpn to get to the professional vpn, that work but we don't like it
View 2 Replies
View Related
May 2, 2012
I configure my new purchase RV042 router, in Access Rule i Deny all services the source is Lan and destination is WAN. my concern is i want to allow LAN to access internet, so i'ved create another rule which allow http, https. but my problem is i cannot access internet.
View 4 Replies
View Related
Jun 12, 2012
brand new RV042 client (tried MacOS and Win7 on two laptops) will get IP from DHCP and shows correct IPs for gateway etc. - however entering the IP 192.168.1.1 to access web admin does not work (tried current versions of Firefox, safari and Firefox); browser is not offline router was reset to factory setting (by pressing reset for over 30sec) ping on IP above works
hardware broken?
View 3 Replies
View Related
Jul 27, 2010
Router is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?
View 20 Replies
View Related
Aug 4, 2011
On my Windows 7 laptop, after connecting to my office Network using Cisco VPN clientThe entire Internet is utilized by the VPN. I am unable to browse the internet on my computer till I disconnect the VPN Client.
View 3 Replies
View Related
Sep 10, 2012
I've setup a GroupVPN and connect to the RV042 with the Shrewsoft VPN client, works like a charm as opposed to QuickVPN ;-)The firewall is configured with an explicit deny rule for RDP access to an internal server, also an explicit allow rule is created for certain IP numbers as source. I noticed that I need to create an explicit allow rule for the subnet the Shrewsoft client is using for the virtual adapter or I will not be able to access the internal server via RDP through the GroupVPN tunnel. I would think that setting up a tunnel defies the rules created for direct access on the WAN port.
View 5 Replies
View Related
Aug 24, 2011
I have an RV042 with the PPTP server configured, which is working because I can connect with my iPad and droid phones, however, I'm unable to access resources on the RV042 side (192.168.1.X) when my local network is the same ip scheme (192.168.1.x). It works fine when I'm on a different network like 3G or someone else's Wifi network (192.168.11.X).
View 1 Replies
View Related
Jan 22, 2013
can i share accouting software like Tally through quick vpn ? WRVS4400n has been configured on the site . and can connect to the site using quick vpn software without a problem . will Tally work ?
View 1 Replies
View Related
Feb 19, 2013
I have access to network 10.3.1.0 /24 but I am not able to access 10.3.2.0/24 and other networks behind the Easy VPN server.I am using a software client to connect to the server.I have configured split tunnel to the network 10.3.0.0 /16 and it shows up in the route details too. I can ping 10.3.1.0 network but not 10.3.2.0 and so on.The Easy VPN server is configured on Cisco 861 with VPN module. [code]
View 6 Replies
View Related
