Cisco Routers :: RV180 Quick VPN To Connect

Aug 6, 2012

I'm having issues getting QuickVPN to connect. I think it's an issue pinging the gateway but I'm not 100% sure. We are using Comcast Business, I have placed the RV180 in the DMZ. The setup looks like this: Internet -> Comcast router -> RV180 (DHCP) -> rest of network.

View 5 Replies


ADVERTISEMENT

Cisco Routers :: Can't Get Quick VPN To Connect To 120w

Jan 29, 2011

For the life of me I can’t get my quick VPN client to connect to my Cisco 120w. I have IPSec gateway to gateway setup and working just fine. I made my quick vpn client under vpn tab. I enabled remote management. Every time I try to connect I get the failed to establish connection. Using the same quick VPN software I can connect to a rv082 with no trouble.

View 2 Replies View Related

Cisco Routers :: Quick VPN Client Cannot Connect To RV042

Apr 7, 2012

PID VID : RV042 V03
LAN IPv4/ Subnet mask : 192.168.0.7/255.255.255.0
Working Mode : Router
 
[code]...
 
PPTP working fine but not with Quick VPN .. test on some computer and internet access still can not get connect to router.

View 79 Replies View Related

Cisco Routers :: Cannot Connect To WRVS4400N Using Quick VPN Client

Oct 6, 2011

Quick VPN and have not had any success connecting with our router.  Below is my components info. Cisco router:   WRVS4400N, Firmware V2.0.0.7.  The router is behind a Comcast SMC business gateway modem Remote computer:  Window 7 Ultimate 64 bit
 
I downloaded the Quick VPN client 1.4.2.1, and installed the client successfully but cannot connect using the VPN Client Account that I had set up in the router.  Below are several questions that I hope to understand.
 
1) Do I need to configure specific ports for VPN in the Comcast gateway firewall?

2) What IP address do I put in the Quick VPN client profile when I connect remotely?  The WRVS4400N modem shows 2 IP addresses in the Status:

DNS1:  68.xx.xx.176
DNS2:  68.xx.xx.132

Are these the IP that go into the "Server Address" on the Quick VPN client profile? and which one of the two?   or do I use the static WAN IP address provided by my Comcast account?

3) In the Quick VPN client window, what is the "Use Remote DNS Server" mean?

4) Do I need to create a client certificate from the WRVS4400N for the client

5) Is there any setup needed for the remote firewall (if the client is behind a home wireless router and modem, for example)?

View 3 Replies View Related

Cisco Routers :: How To Connect OS X 10.7+ To RV180 VPN

Mar 2, 2013

Which vpn client to use on os x ? (the one included in os x or another?) Which VPN configuration to use on RV180 ? and Which ports to open on RV180 Firewall ? (or any other parameters)

View 1 Replies View Related

Cisco Routers :: RV180 Router Will Not Connect To ISP

May 16, 2012

I am contemplating replacing my Juniper Netscreen 5GT with this new RV180.
 
serial number 161303LB 
RVC180 V01
 
However, it will not connect to my ISP (DSLExtreme) using the same settings I have been using for multiple years. DSLExtreme is using AT&T DSLAMS, as you likely know, and I am unaware of anything unique about how they serve DHCP?
 
The Cisco wizard sits on the WAN configuration check forever, and never connects. I have rebooted it and allowed it to sit for fifteen minutes trying. I think that is enough.
 
The 5GT WAN interface is configured for "DCHP Client" and that is how the RV180 is configured.
 
It is a standard 6MB DSL line, I have tried both the existing cable, as well as the provided one to connect to the D-Link 2320B modem/bridge, which, as I indicated, syncs almost instantly with the Netscreen. No difference when the cables are swapped.

View 3 Replies View Related

Cisco Routers :: RV180 Will Not Connect To ISP Using PPPoE

Mar 17, 2013

The RV180W would not connect to an AT&T DSL connection using PPPoE (modem in bridge mode), or behind the DSL Modem/router with the DSL modem/router providing a dynamic IP to the RV180W or a cable modem (TimeWarner Roadrunner dynamic IP).  I upgraded the firmware yesterday and now the RV180W will connect to a dynamic WAN IP, but it still will not connect using PPPoE.
 
I have also noticed the admin interface is only accessible about 75% of the time.  When going to 192.168.1.1 the login prompts either don't come up or if they do, after logging in, the screen never fully loads after that.  I have to reboot the router to get it to work.
 
Also, the router has not yet pulled DNS from either the DSL or the cable modem.  I had to manually enter those addresses.

View 1 Replies View Related

Cisco Routers :: Connect L2L Between RV180 And ASA5505?

Feb 27, 2013

I've been trying to connect L2L between RV180 and ASA5505 but no succeed.I can do RV180 to RV180 l2l with one of it on Aggresive mode. working configuration sample of RV180 L2L ASA5505?

View 1 Replies View Related

Cisco Routers :: RV180 Behind DSL Router Can't Connect With QuickVPN

May 15, 2013

I want to ask if is possible to configure the RV180 behind my DSL Router to connect using QuickVPN. First I tried to connect to the PPTP server and worked fine, but when I tried to connect using QickVPN, seems to connect but when the client says "verifying network" after a while appears the message "network not responding..."
 
In my DSL-Router forwared this ports: UDP: 500,4500,443,60443 - TCP: 443,60443 (i don't know if tcp ports are needed but I opened for testing) and allowed protocol ESP (comes with the rule to allow IPSEC-L2TP)

View 3 Replies View Related

Cisco Routers :: RV042 Quick VPN Does Not Disconnect

Mar 3, 2011

we bought a router for our company RV042, so far good
 
What i did:
 
1. i created QuickVPN clients, droped in certificate which exported from router
 
******NOTE********All company's laptops are running: Windows 7pro 32bits****************
 
The users are connecting sucesefully to router and using resources from server etc...
 
But, when they press disconnect on quickVPN it shows disconnected, but when i log in into router, i still see that they are connected (not disconnecting),
 
and the problem is they cannot connect to router second time if i don't manually disconnect them from rv042 router....
 
Only sometimes the clients disconnect properly from router, but it is very very rare...
 
Question1: Where I should look for the problem in router rv042 or client laptops?
 
Question2: Does the 64bit windows7 pro OS can connect to RV042router?
 
I have latest quickvpn software and latest router firmware.

View 10 Replies View Related

Cisco Routers :: 1194 Ports Used By Quick VPN

Nov 1, 2011

we recently bought a new desktop firewall solution from McAfee and I can't seem to get our VPN to work. I allowed QuickVPN in the firewall and additionally opened port 1194, 1720 and 1723 - but that does not do the trick. Once I turn off the firewall and use Windows Firewall instead it works.

View 2 Replies View Related

Cisco Routers :: Unable To Access LAN Behind RV042 From Quick VPN Client?

Aug 22, 2011

Very recently, we had implemented Site-to-Site VPN tunnel between two Linksys RV042 4-port VPN routers. Everybody in our remote site is accessing and sharing the data through this tunnel and it is working fine.
 
Now, we have a plan to implement the same for our mobile clients also. For this, we had followed all the basic configuration procedures and user got connected to Quick VPN tunnel. Here is a problem we had observed. The mobile client user is connected to the tunnel, but unable to access the office LAN from the PC.

View 1 Replies View Related

Cisco Routers :: WRVS4400N And Quick VPN (remote Gateway Not Responding)

Jul 27, 2010

Router is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
 
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log  [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?

View 20 Replies View Related

Cisco Routers :: WRVS4400n Can Share Accounting Software Like Tally Through Quick Vpn

Jan 22, 2013

can i share accouting software like Tally through quick vpn ? WRVS4400n has been configured on the site . and can connect to the site using quick vpn software without a problem . will Tally work ?

View 1 Replies View Related

Cisco Routers :: Rv042 Quick VPN Windows 7 Unable To Access Network Shares Or Ping

Nov 26, 2011

I have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.

View 1 Replies View Related

Cisco Routers :: RV180 Ssh And Https From WAN?

Dec 23, 2012

Is there any way to manage the RV180 from the WAN side via https and/or ssh?Also, is ssh from LAN even available?

View 3 Replies View Related

Cisco Routers :: RV180 VPN Does Not Work

Oct 18, 2012

I have an RV180 VPN router.I try to enable the VPN users with PPTP or QuickVPN but is not working.For PPTP sometimes my windows 7 connects to the router, sometimes doesn't connect with a random error message.When it connects, the windows 7 from outside the lan can see the computers from inside the lan but the computers from inside the lan cannot see the windows7 one. This is random also. When i succed to connect, from that computer, the internet is not working anymore.I tried to set the VPN in the same subnet as lan, i tried with different subnet. Is not working.I updated the last firmware. The same.Restore factory settings couple of times, the same.

View 6 Replies View Related

Cisco Routers :: Bug In RV180 Firmware V1.0

Jun 17, 2012

I noticed if you add more than 10 access rules to the Access Rule table, you are unable to reorder past the first 10.Steps to reproduce:Create 11 rules of the same stream direction, outbound or inbound (...I found the bug with outbound, did not test inbound).try to reorder one of the first 10 rules to the end of the list, either by entering "11" manually, or by pressing the down arrow.System responds that "11" is an invalid number, or that the rule cannot be moved.This issue is not reported in the "Known Issues" section of the release notes for 1.0.1.9.

View 2 Replies View Related

Cisco Routers :: RV180 - Log Warnings With QOS IP Or MAC

May 20, 2013

I had set up QOS for an IP Range and noticed the logs filling up with Warnings - hundreds within less than an hour.
 
I finally reset the router to factory and then step by step re-built my configuration - it was the QOS that started generating these warnings like:
 
Tue May 21 13:18:39 2013(GMT-0500) [rv180][Kernel][KERNEL] [87073.550000] IN=bdg1 OUT= DST MAC=d8:67:d9:c3:a0:2e SRC MAC=00:0e:58:58:57:7a PAYLOAD TYPE=08:00 SRC=192.168.1.193 DST=208.85.44.22 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=19313 DF PROTO=TCP SPT=1768 DPT=80 WINDOW=2534 RES=0x00 ACK URGP=0 MAR

[Code].....

In both cases above, after I started to suspect QOS, I entered a narrow IP range to test and then a MAC to test.  Using a VLAN seems to work fine and generate no errors - even a VLAN for the same associated host(s).
 
I have a support case open about this - didn't get too far yet, but now with a better repro, maybe they will.

View 1 Replies View Related

Cisco Routers :: RV180 What Are The Alternatives For Android ICS

Oct 30, 2012

I  currently have an RV180 in a small business set-up and curently being  accessed remotely by laptops (Quick VPN) and Ipads/Android ICS tablets  (PPTP).  All is working well but I've become concerned about the  security risks of PPTP and would like to shift the tablets to IPSec. 

1) For a  small business are the PPTP risks real?

2) What are the alternatives for Android ICS?  I can't find a Quick VPN client for Android.

3) I can't get the core IPSec VPN in Android to connect to the RV180?  Is this possible? 

View 1 Replies View Related

Cisco Routers :: NATed Did Not Add VLAN On RV180

May 7, 2013

I have RV180 configured with two VLANs. First VLAN is untagged and second VLAN is tagged. The purpose is two have two subnets, with the second subnet used for guest access. Both VLANs have DHCP server enabled. First VLAN is 192.168.1.0/24 and the second VLAN is 192.168.2.0/24, When I connect a computer with untagged Ethernet interface, it gets an IP address from DHCP server on the first subnet i.e. 192.168.1.100 and it can successfully access Internet. When I connect a computer with tagged Ethernet interface (I am using VLAN ID 10), it gets an IP address from DHCP server on the second VLAN i.e. 192.168.2.100. So far so good. I can successfully ping hosts on the Internet i.e. ping www.google.com. But I cannot access Internet from the web browser. I captured Wireshark trace and here is what I see...

1. TCP SYN. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
2. TCP SYN ACK. Source IP A.B.C.D, destination IP 192.168.2.100. Ethernet frame has VLAN tag (VLAN ID 10)
3. TCP ACK. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
4. TCP Data. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
5. TCP Data. Source IP A.B.C.D, destination IP 192.168.2.100. Frame is untagged
 
The problem is at #5. Packet came back from the Web Server. RV180 properly NATed it to the local IP address. But it did not add VLAN tag.

View 8 Replies View Related

Cisco Routers :: Rv180 Dropping LAN Connections?

Mar 13, 2013

I just recieved a new RV180 yesterday and it will not connect to my switch. Router was updated to the newest firmware, reset to factory settings. I did change the ip and ip range. Router works fine with one computer attached direct. As soon as I connect my sf300-24P to it, the WAN and LAN lights all light up and then go out. Only the WAN will light back up. I have no connectivity to the router. I plug the laptop to the router directly and no LAN lights come on and can not see the router with arp -a.

View 6 Replies View Related

Cisco Routers :: How To Enable Telnet On RV180

Mar 9, 2013

I'm trying to telnet into the my RV180 router. How do I go about it.
 
I created 3 VLANS

1  at 192.168.1.1
20 at 192.168.20.1
30 at 192.168.30.1
 
Here is the Multiple VLAN Subnet Table:

1     192.168.1.1    255.255.255.0DHCP ServerEnabled 10192.168.10.1255.255.255.0DHCP Server  Enabled 20  192.168.20.1 255.255.255.0    DHCP ServerEnabled 

I can ping the router at all 3 IP addresses.How do I enable the telnet service on the router?

View 1 Replies View Related

Cisco Routers :: RV180 And IPSec VPN Client

May 22, 2012

Does RV180 router support client VPN connections using regular Cisco VPN client? Datasheet says it works with Quick VPN client.

If regular non-Quick client is not supported, can both clients coexist (= be installed simultaneously) on the same PC?

Does Quick VPN client support split tunneling?

View 2 Replies View Related

Cisco Routers :: Does The RV180 Series Support 6rd

May 10, 2012

I'm considering upgrading a small business to the newly released RV180 or RV180W.Does the RV180 series support 6rd (IPv6 rapid deployment?).I see 6rd documented in the other small business routers (e.g. RV110), but I can't find it in the RV180 documentation.

View 1 Replies View Related

Cisco Routers :: RV180 VPN Guide Required

Apr 3, 2013

Is there a guide to setup a VPN connection using this router? I've follow the setup guide provided by cisco but I'm having issues.  When attempting to connect using the quick vpn client, I get error messages.

View 1 Replies View Related

Cisco Routers :: RV180 IPSec Needs Polishing

Apr 26, 2013

Any news on a new firmware for the RV180? I have the most recent version but it still has lots of bugs. IPSec needs polishing. In addition the Logging functions don't work well. I can't send to a syslog and when I try to email the logs I get a email saying there is no data even though several pages of enteries are visible in the web GUI. I've checked the profiles and they are correct. I even tried using just the 'default' profile but no luck.

View 2 Replies View Related

Cisco Routers :: SB RV180 VPN Users Not Showing Up?

May 15, 2013

I have a Cisco Small Business RV180 and I have several VPN users configured.  IPsec between my home router (also an RV180) and work router (router in question) is working fine, several PPTP users working fine and 1 QVPN user that works as well.  I set up another qvpn user and it didn't work.  I went back into the router to check and make sure I hadn't goofed something up and saw that I had 8 lines, 1 and 2 were the QVPN users and 6 other PPTP users, however, the "pages" footer (for lack of a better word) only displays 1 -5 of 5 instead of the 1-8 of 8 I would expect it to show.I dumped the cfg file and opened it up, all 8 user configurations show up.  One was my user account which showed negative numbers for the logon time, something like -1day -hours -minutes -sec, so I thought that that might be locking up the router or something so I deleted my PPTP account but it didn't allow the new user access.  I deleted all PPTP accounts and no luck there either.I'm running firmware 1.0.2.6.

View 4 Replies View Related

Cisco Routers :: Very Slow WAN Speed (RV180)?

Jan 30, 2013

My brand new RV180 seems not to be able to exceed 1.1 MB/s WAN download speed. Using a simple Linksys WRT-320N I used to have 5-6 times this speed. Value is with default settings, various sources (HTTP/NEWS downloads). Trying to improve this wit QoS-settings dows not improve this in any way.

View 2 Replies View Related

Cisco Routers :: RV180 PPPoE Not Working

Oct 15, 2012

My RV180 does not route properly between LAN and WAN through my PPPoE account. I am able to ping public IPs directly from the RV180 (through the diagnose section) but can not do it from any PC on LAN. The exact same configuration works perfectly well with a Linksys WTR610N. I upgraded formware from 1.0.0.30 to 1.0.1.9 but that did not make any difference.
 
The only time the RV180 will route is right after I reset to factory defaults and re-enter PPPoE account name and password. If I then reset my modem or the RV180, the RV180 does not route anymore between WAN and LAN even after several minutes and even though I can ping public IPs from the RV180.

View 18 Replies View Related

Cisco Routers :: RV180 With AnyConnect 2.5 VPN Using DTLS

Sep 17, 2012

My work laptop uses a Cisco AnyConnect VPN Client (Software Version 2.5.2006). The connection protocol is DTLS.I recently upgraded to a Cisco RV180 at home at it is running the latest software version (1.0.1.9).
 
Since the RV180 went into service the work laptop will connect intermittantly. Usually email works but web browsing and and other services do not. It is slight strange behaviour- and seems to defy what a VPN should do......
 
The behaviour is very repeatable. For example from the customers office the laptop connects perfectly via VPN and if I swap back to an older inferior make of router at home VPN also works normal without changes to the laptop configuration.
 
I work for a large company (70,000+ employees) and we use "standard" builds so altering the laptop configuration is not really an option.
 
It seems to me that the RV180 doesn't support the DLTS VPN connection (indeed DLTS passthrough isn't an option in the VPN passthrough list) and is possibly blocking some incoming packets on the WAN interface.
 
I haven't yet tried a firewall rule to allow a DLTS (or UDP perhaps?) connection back in from the WAN side (obviously from just the IPs at my work end) but this is the only option I can think of to make this machine connect "correctly".

View 3 Replies View Related

Cisco Routers :: RV180 X-Box Block On Schedule

Mar 18, 2013

This week, I replaced a netgear FVS318G with a Cisvo RV180, firmware 1.0.2.6.  I have a very limited knowlege of routers and protocols, mostly from exposure as a home user.  My goal is to define firewall rules on my RV180 that define when my tween-aged kids can and cannot play on X-Box live, as was the case on the FVS318G.  I am aware that X-Box has several port ranges.  Specifically, I have defined the following for one XBox port range to always block, as an example:
 
[code]...
 
A similar rule on the FVS318 would block XBOX (and also on a schedule), but this is not the case on the RV180.  I guess I don't uderstand how to correctly implement rAccess Rules on this device.

View 1 Replies View Related

Cisco Routers :: RV180 Access Rules And One-to-One NAT

Nov 15, 2012

I have 2 static IP addresses that I'd like to point to 2 corresponding servers in my LAN.  I've followed the Access Rule and One-to-One NAT instructions as best I can (screenshots of each for one of the static IP scenarios attached), but no luck.  The static IPs bring the outside/WAN user to the RV180's admin login screen.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved