can i share accouting software like Tally through quick vpn ? WRVS4400n has been configured on the site . and can connect to the site using quick vpn software without a problem . will Tally work ?
View 1 Replies Quick VPN and have not had any success connecting with our router. Below is my components info. Cisco router: WRVS4400N, Firmware V2.0.0.7. The router is behind a Comcast SMC business gateway modem Remote computer: Window 7 Ultimate 64 bit
I downloaded the Quick VPN client 1.4.2.1, and installed the client successfully but cannot connect using the VPN Client Account that I had set up in the router. Below are several questions that I hope to understand.
1) Do I need to configure specific ports for VPN in the Comcast gateway firewall?
2) What IP address do I put in the Quick VPN client profile when I connect remotely? The WRVS4400N modem shows 2 IP addresses in the Status:
DNS1: 68.xx.xx.176
DNS2: 68.xx.xx.132
Are these the IP that go into the "Server Address" on the Quick VPN client profile? and which one of the two? or do I use the static WAN IP address provided by my Comcast account?
3) In the Quick VPN client window, what is the "Use Remote DNS Server" mean?
4) Do I need to create a client certificate from the WRVS4400N for the client
5) Is there any setup needed for the remote firewall (if the client is behind a home wireless router and modem, for example)?
Router is a version 1.1 running with sw version V1.1.13-ETSI
Quick VPN is sw version Ver 1.4.1.2
The issue is that I can't connect due to that i cant ping the internal IP, get this error message in the QVPN log [WARNING]Failed to ping remote VPN Router![URL]I have disable the "Block WAN Request" and it is possible to ping the router on the external site.So as I see it, the router blocks for ping on the internal IP via QVPN, what have I done wrong?
I have a WRVS4400N router & am using Quick VPN to connect to the Router. I can able connect through Window XP Machine, but not able to connect through Window Vista & 7. Whenever I try to connect through Window 7, I got this message: The remote gateway is not responding. Right now the Cisco router is behind DSL modem and I can't change the DSL modem to bridge mode as my ISP told me that we can't change DSL modem to bridge mode. what I have to do to connect to the router through Windows 7 & Vista.
View 3 Replies View RelatedWRVS4400N v2.0 2.0.0.8
QuickVPN 1.4.1.2
Vista Home Premium SP2 64-bit
Trying to connect from laptop through an AP to my WRVS4400N via VPN. Not having much luck...I get to "Activating Policy..." and then "Connection Error".I like this router thus far, I have been able to set up multiple BSSIDs and VLANs which has been very useful.
For the life of me I can’t get my quick VPN client to connect to my Cisco 120w. I have IPSec gateway to gateway setup and working just fine. I made my quick vpn client under vpn tab. I enabled remote management. Every time I try to connect I get the failed to establish connection. Using the same quick VPN software I can connect to a rv082 with no trouble.
View 2 Replies View RelatedI'm having issues getting QuickVPN to connect. I think it's an issue pinging the gateway but I'm not 100% sure. We are using Comcast Business, I have placed the RV180 in the DMZ. The setup looks like this: Internet -> Comcast router -> RV180 (DHCP) -> rest of network.
View 5 Replies View Relatedwe bought a router for our company RV042, so far good
What i did:
1. i created QuickVPN clients, droped in certificate which exported from router
******NOTE********All company's laptops are running: Windows 7pro 32bits****************
The users are connecting sucesefully to router and using resources from server etc...
But, when they press disconnect on quickVPN it shows disconnected, but when i log in into router, i still see that they are connected (not disconnecting),
and the problem is they cannot connect to router second time if i don't manually disconnect them from rv042 router....
Only sometimes the clients disconnect properly from router, but it is very very rare...
Question1: Where I should look for the problem in router rv042 or client laptops?
Question2: Does the 64bit windows7 pro OS can connect to RV042router?
I have latest quickvpn software and latest router firmware.
we recently bought a new desktop firewall solution from McAfee and I can't seem to get our VPN to work. I allowed QuickVPN in the firewall and additionally opened port 1194, 1720 and 1723 - but that does not do the trick. Once I turn off the firewall and use Windows Firewall instead it works.
View 2 Replies View RelatedPID VID : RV042 V03
LAN IPv4/ Subnet mask : 192.168.0.7/255.255.255.0
Working Mode : Router
[code]...
PPTP working fine but not with Quick VPN .. test on some computer and internet access still can not get connect to router.
Very recently, we had implemented Site-to-Site VPN tunnel between two Linksys RV042 4-port VPN routers. Everybody in our remote site is accessing and sharing the data through this tunnel and it is working fine.
Now, we have a plan to implement the same for our mobile clients also. For this, we had followed all the basic configuration procedures and user got connected to Quick VPN tunnel. Here is a problem we had observed. The mobile client user is connected to the tunnel, but unable to access the office LAN from the PC.
I have an RV042 using Quick VPN to connect to a remote network. I have port 1723 forwarded to a static IP address on a Windows 7 Pro 64 bit PC. I can establish the VPN and ping a printer but not the Win 7 PC. I can not acccess any shares on the pc via the IP address. It has Norton Antivirus and Windows Firewall. This remote PC replaced a Windows xp PC that allowed access to the shares. I have tried access with a Windows XP Pro and Windows Vista Home Premium PC. Neither have worked.
View 1 Replies View RelatedRight out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies View RelatedI'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies View RelatedI'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?
View 1 Replies View RelatedI have successfully got QuickVPN working from Windows 7 64bit into my WRVS4400n. The router is sat behind another router/modem (Belkin) as the UK uses PPPoA and the WRVS4400n doesn't.So I set up DMZ and changed the DHCP to always allocate 10.x.x.2 on the Belkin which is the WAN side for the WRVS4400n as it is the only thing attached.I have now noticed, and I'm not sure whether it was the case before, that the DNS that the WRVS4400 is showing is the LAN address for the Belkin Modem/Router (10.x.x.1), not 192.x.x.1 for the WRVS4400n itself. I assumed setting the Static DNS 1 on the WRVS4400n would do it, but it didn't?When I connect into the network with QuickVPN, the computer names do not show even though I have selected the option in QuickVPN?
View 1 Replies View RelatedOur business was looking at purchasing one of these Cisco routers and were curious if it supported WPA2 EAP-TLS?
View 2 Replies View RelatedI have 2 WRVS4400N's available to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies View RelatedRecently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
I'm having a heck of a time connecting the WRVS4400N VPN to another WRVS4400N VPN. both of the routers have the current firmware version V2.0.2.1: Router 1 is below, and router 2 has the matching configuration with as it should be the local group being that routers local information and the remote crew set up being router ones information. the status is up on both of the routers, but I'm unable to ping the remote gateway or any device behind it.[code]
View 5 Replies View RelatedAfter a few months of trouble-free ... the Cisco WRVS4400N V2 stopped working. i have tried to reset by holding the reset button for 30 seconds ... but nothing changes the red DIAG light remains on at all times
i have also tried two different versions of the Firmware Rescue Utility but all i get is "unable to scan"
How to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.
This is a new device, just initially installed about a week ago. I updated to the latest firmware. We have iphones, ipads, and Samsung Galaxy smartphones all trying to connect to this WAP at this office, but cannot seem to connect. If I power cycle the WAP, we can connect for about 5 min, then it loses it and cannot connect again. I have strong signal, device says "connecting" then immediately "disconnected"... does this on loop forever.WPA/WPA2 PSK.I don't know what to do. About to go buy an Apple WAP.
View 3 Replies View RelatedMy WRVS4400N is not letting my VPN client through the router. I have checked the passthrough boxes for all 3 protocols. I have port range forwarding for my VPN connections to my SBS2008 box on port 1723.
View 5 Replies View RelatedI have a Linksys E4500 as the main router and would like to use the WRVS4400N as a bridge to extend the range of my network and also attach a NAS to it. Is this possible? I've been trying different options but have been unsuccessful.
View 1 Replies View RelatedLooking for a working Cisco VPN client for Windows 7. There seems to be an availabel download for a ver 5, but you have to be a reseller etc.. Where do I download the Windows 7 supported VPN client to access my WRVS4400N router? If none, should I use 3rd party - IF yes to 3rd party, which one would you suggest?
View 1 Replies View RelatedI bought a WRVS400N v2 to be used as an access point. Currently it is hooked up on my switch via a trunk port and is able to communicate with my gateway. Whenever I try to access an IP subnet other then the local IP address of the WRVS, I get a network unreachable error. To fix this for my local networks, I added the appropriate static route to cover my local LANs and that seems to work now. I tried to add route 0.0.0.0/0.0.0.0 using the web interface for internet access, but somehow it does not recognize this as a default route (quad zero!?). Does any know how I can set the default gateway in this router? Maybe, but hopefully not, I have to use the WAN port to create some kind of uplink and use one of the LAN ports to connect using the trunk port and route traffic for the clients over the WAN port .
View 1 Replies View RelatedI have three locations using the linksys wrvs4400n router with IPSec VPNS. They all work fine and point back to a Server2003. I just added a fourth location with the same router but this new router has firmware v2.x, where the others have firmware v1.x. When I connected the new router into the VPN network, it caused the other tunnels to go down. When I take the new router with firmware v2.x offline, everything else seems to work fine.
Can the v2.x firmware cause the other VPNS on v1.x firmware to go down and not work properly? Do I need to upgrade the firmware so all 4 linksys wrvs4400n routers are operating the same version number so not to cause the tunnels to disconnect?
I have looked through the forum for answers to my problem, but does not look like I'll find it.The problem: Router randomly freezes.When this happens:No IP/DNS,No response to ping,No contact at all (wifi or cable),Works fine after reboot for some time.
View 2 Replies View RelatedI have a E3000 router (wireless N and gigabit ports) and a 50mbps download/8mbps upload Internet connection with machines attached directly to the ethernet ports on the E3000 I can get full speed 50mbps download doing speedtest
now I have a cisco WRVS4400N connected to the E3000s etherenet port going to the WAN port of the WRS4400N.
I'm able to get intnet access on my device/computers fine. Problem is that when I did a speed test from devices attached to the Cisco WRS4400N router my max download speed is only 26mbps out of the 50mbps (it's not network congestion as I did the same test from devices attached to the E3000 and I can get full 50mbps)
Is there any setting on the WRVS4400N that might speed things along? or is the WAN port maxing out the download speed at 26mbps?
after being able to see the cctv on the local network and remotely, we are simply not able to connect remotely again. This happens several hours after leaving site. The clients ip seems to be unchanged from last time, and we do get a " resource online but isn't responding to connections attempts" message from IE8. The ports have never actually shown as open from online port verification sites, but again, we were able to see the cams via 3g and from another town just fine.And we can see them on the locally. I'm convinced it has to be some setting on the router relevant to port forwarding.
View 3 Replies View Related