How to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.
WRVS4400N needs to be manually connected when the power is recycled after power failure. Is there a setting to connect an IPSEC VPN automatically, instead of manually going in to connect the VPN
View 3 Replies View RelatedI need trouble-shooting wireless network connectivity issues that arose recently:We use a Comcast modem and two WRVS4400N's as wireless routers/wireless access points.We recently got our comcast service upgraded to 100/20 and also got rid of our static ip address. As a result (I think there must be a sort of causal relationship here, but I'm not sure what it is) we can no longer connect to the internet using our wireless networks. We can connect to the wireless network, but have "No Internet Access."
View 4 Replies View RelatedWe just purchased the WRVS4400N router with high hopes. For some reason, our ISP provides a connection through L2TP Dynamic for a static IP. I repeat, L2TP Dynamic. Is there anyway to properly configure the router to use such a connection method. I only see L2TP Static, which seems to be the standard method for many routers.
View 1 Replies View RelatedI am having some difficulties using RDP on the LAN of the router. I previously had a Linksys E4200 router, and I was able to RDP from my Win7 computer (192.168.1.139) to my Win2k3 server on the LAN (192.168.1.251) with no issues. However, when I replace the E4200 with the WRVS4400N, the connection will only work for a few seconds.
It is not exclusive to RDP connections on the LAN either... I get a similar error when attempting to connect to computers off site. I could see MTU's being an issue if it was over a VPN connection, but there is no VPN involved in this case.
I see a lots of problem associated with wirless connectivity with WRVS4400N, with following config
Firmware version - Firmware Version: V1.1.13
Wireless connectivity - G/N Mixed
Auth - WPA2 AES
Everything else default and AUTO,
Problem:The end devices suddenly drop connection. Wired connection works just fine. The DROPPED device can not be reconnected. On MAC I get AUTH time out. I see the SSID being broadcasted from my HTC wireless analyster so radio may not be the problem. I changed to set the speed to G only or N only but not avail. ONLY way to recover from this is rebooting the router.
I have a Cisco WRVS4400N on the latest firmware and I have just had my Virgin internet connection upgraded to the 100Mb. Once i thought it was upgraded i checked with a broadband speed test and it came back as 15Mb download and 5Mb upload. Before i rang Virgin i thought i'd check with a direct connection from my pc straight to the modem. Ran the speed test and it came back as 100Mb download and 5Mb upload. I thought the best thing to do is restore my settings back to factory and its still the same.
View 7 Replies View RelatedI have a Samsung Galaxy 10.1 tablet and have bee trying to connect to my WRVS4400N router with VPN through the "on board" software as well as with the Any Connect software from Cisco. I have no issues at the moment using Quick VPN from my laptop.
When using the Any Connect software I receive the following messages:
Security warning: untrusted certificate
AnyConnect cannot verify the identity of <IP address>. Would you like to continue anyway?
- Certificate does not match the server name.
- Certificate is from an untrusted source.
- Certificate is not identified for this purpose
[Accept] [Details] [Cancel]
If I select accept, the following error is received:
"Error: Connection attempt has failed due to server communication errors. Please retry the connection".
I have tried setting up the on board VPN with the Samsug Galaxy but every attempt has resulted in a time-out of the connection.
For eight months we have not had any problems with our new WRVS4400N (V2.0.2.1) connected to a Verizon/Westell 6500 to provide DSL internet for our network with DHCP on our server... No changes have been made to the router or modem since initial setup; but, then it started -- Our internet connection would drop intermittently. Sometimes every 5 or 10 minutes - sometimes every hour. Verizon has tested the lines which came up ok, then they sent a tech who changed the wire pair coming into the building for the DSL line and retested the lines which again came up ok, then they provided us with a new modem (now a Verizon/Westell 7500). After all that, the DSL still connects then disconnects intermittently. I am now wondering if the issue lies with the WRVS4400N.
View 2 Replies View RelatedI am trying to setup VPN with WRVS4400N and Quick VPN on client side. I am fairly new to VPN and did some research and looked through the manual but can't seem to get it to work so far and from what I noticed many people are having this problem.
Basically it gives the "Failed to establish connection" generic error, shows it almost instantly.It also showed the certificate error before but then I read about putting it in the installation directory and it stopped showing it, and whats strange is later I removed it but it doesnt show the error any longer, so don't know if its caching it somewhere or what can be going on...
In effort to look for answer and test things out I tried to connect to another location and setup a WRV200 router, I also get the same error but not instantly, it even shows "Activating Policy" but then doesn't go farther and shows the generic error.Also with this setup strangly it always shows the certificate error, no matter if I put one in directory or not... Even tried to name it as the WRVS4400N certificate name...
Anyway VPN IPSec is disabled, and Client Accounts are configured and changed password several times to make sure its correct, VPN Passthrough enabled on all 3 options. I tried to disable Windows Router, I also have a router in place do I possibly need to open some type of ports for the QuickVPN client?
My ISP provides IPv6 connectivity in the form of dual stack IPv4/IPv6 with DHCPv6 Prefix Delegation. Using a Cisco IOS-based router I managed to make such a connection by using as a template the Cisco IOS configuration file that my ISP has posted as an example in the following link:
[URL]
The main point on this configuration is a PPPoE connection with:
interface Dialer46
ipv6 address autoconfig default
ipv6 enable
[Code].....
configure this router according the Cisco IOS configuration file I linked on the top in order to have a working IPv6 connection?
I did upgrade to WiSM from v5.1 to V6 then i see this log %WCP-3-KEEPALIVE_LOST: wcp_controller_server.c:1763 Lost keepalives from Cat 6K Supervisor.
View 6 Replies View RelatedI Have a Computer Ready for setup as a Server in the LAN Connection:
Windows 7 Professional.
Another 2 Computers for LAN Connection:
1st Computer is a Windows 7 Professional (Connect as LAN)
2nd Computer is also Windows 7 Professional (Must connect using a Wifi D-Link)
Another 2 Computer for LAN Connection:
Windows XP: Must Connect Using LAN port.
1 Computer:
Windows 7 Home Edition: Must Connect Using LAN port
2 Laptops:
1st Laptop is using Windows 7 Ultimate.
2nd Laptop is a Vista.
How to Connect these Computers to the above mentioned computer ready for setup as as Server?
i bought this router because I wanted a gigabit router for my small business and I figured whats better than a small business router? Well, one think I used pretty heavily on my Linksys WRG54GS was a simple port forward to my XP box for VPN. I know nothing about how to currectly set up VPN in this router. Does this router have a built in VPN server? Also, is there anyway to completely disable everything VPN side on this router and simply forward my port 1723 to my computer again? I am using this in conjunction with my android phone. I downloaded the AnnyConnect software, but yielded zero success. I have a working tun.ko installed on my rooted android phone, but this all is completely too much work for something that worked very well before using simple port forwarding and the built in vpn client on the phone. How can I correctly set up my router for the VPN to use with the AnnyConnect application I have on my cell phone?
View 1 Replies View RelatedI have a Rv082 router that works great and I added a Cisco wireless Wap4410n to one of the ports and it works great for all my wireless connections. My problem is I cannot set up any security on the wireless connection. I see it on network majic pro but cannot access it thru my router . Do I have to install a poe switch first?
View 0 Replies View RelatedI have a WRVS4400N setup as a main router for one of our bays. For wired connections it is working with no problems. When I first installed it it ran fine for wireless as well. I was trying to get WDS to work and at some point the wireless stopped working. My laptop can no longer connect to it and often cannot see it when doing a scan for networks. I have already checked that it isn't a problem with the laptop, that there are not other networks causing interferance, and even tried resetting to default configs.
View 1 Replies View RelatedIs it possible to setup a router to router connection over the internet with fixed IP Addresses with two WAG320N?
View 3 Replies View RelatedA query here with regards to Wireless isolation between SSID and wireless isolation within SSID.If we have 2 SSID, eg. InternalSSID, GuestSSID on AP1.Both SSID are set to Enabled for isolation between SSID, and within SSID, that would mean all machines connected thro' this AP1, would be isolated from one another.
1) If there's 1 laptop that connects to another AP, lets call it AP2, (doesn't have isolation function) on ssid01. Would this laptop still be isolated from those that connects to the first AP?
2) If there are wired PCs connected to the router. And the 2 APs are connected to the same router. Would the machines connected thro' the AP1 on either InternalSSID, GuestSSID be able to access those wired PCs? (My assumption is yes.)
3) Is there a quick and efficient way to setup on WRVS4400N to isolate GuestSSID totally from InternalSSID, and wired PCs. InternalSSID and wired PCs should be allowed to 'see' one another.
The challenge here is that, the network points are all installed already. Both AP are connecting thro' 2 separate unmanaged switch together with a couple of other PCs. 1 Port on the unmanaged switch, each,connects to the router.
I work at a small private school that is going to implement about 20 ipads for classes. Students bring their ipods and iphones and are connecting to the existing unsecured wireless access points and are taking up the remaining IP addresses in the DHCP scope. I am running out of IP addresses and was wondering if I could set up a VLAN using the Cisco WRVS4400N for all of these wireless devices the students will be using. I plan to pull out all unsecured wireless AP's and replace with what ever solution we come up with. I will need about 6 access points/routers to cover the entire school. There is not a lot of money for technology and the ipods were donated. I have never set up a VLAN before. Is there an inexpensive way to allow the students with their personal ipads/ipods and the 20 ipads owned by the school to connect to a VLAN to keep from using up our DHCP IP addresses from the server.
View 1 Replies View RelatedI would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
Right out of the box, the WRVS4400N [firmware v2.0.1.3] I just purchased says the WAN interface is DOWN; and it simply will not obtain an IP address from the Arris TM602G cable modem it is attached to. Internet still runs great on the old WRT54G. Is this WRVS4400 DOA? Or is there some arcane setting the quickstart guide overlooks? OR?
View 2 Replies View RelatedI'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies View RelatedI'm having problems trying to establish a IP Sec tunnel from the office to home. All of our machines are Macs so I have been using the directions described in "How to create an IP Sec tunnel for MAC Clients, A QVPN alternative" but I still can't get it to work. My setup is as follows:
The office is connected to the outside world through a MODEM (Sagemcom 2864 Connection Hub). This MODEM is also a wireless router. It's DHCP server provides addresses 192.168.2.x.The WRVS4400N's WAN port is connected to one of the LAN ports on the MODEM. It's IP address from the MODEM is 192.168.2.x. The WRVS4400N provides addresses 192.168.21.x to devices connected to it.We have a DynDNS account and are using the DDNS client on the WRVS4400N router to connect to it.At home, we have a DIR-655 router with IP Sec Passthru enabled. The router provides IP addresses 192.168.1.x for all devices connected to it. I am fairly sure there are no issues with the router setup at home since I am able to VPN into the office of my full-time job without any problems. I have tried just about everything I can think of but have not been able to get this to work. setting up the Local and Remote Group Settings on the WRVS4400N and the IP address settings in IP Securitas?
Ive setup a few WRVS4400N over the past 6 months, and have been receiving the below message from some of them every couple of hours.What does the message indicate?
View 1 Replies View RelatedI have successfully got QuickVPN working from Windows 7 64bit into my WRVS4400n. The router is sat behind another router/modem (Belkin) as the UK uses PPPoA and the WRVS4400n doesn't.So I set up DMZ and changed the DHCP to always allocate 10.x.x.2 on the Belkin which is the WAN side for the WRVS4400n as it is the only thing attached.I have now noticed, and I'm not sure whether it was the case before, that the DNS that the WRVS4400 is showing is the LAN address for the Belkin Modem/Router (10.x.x.1), not 192.x.x.1 for the WRVS4400n itself. I assumed setting the Static DNS 1 on the WRVS4400n would do it, but it didn't?When I connect into the network with QuickVPN, the computer names do not show even though I have selected the option in QuickVPN?
View 1 Replies View RelatedOur business was looking at purchasing one of these Cisco routers and were curious if it supported WPA2 EAP-TLS?
View 2 Replies View RelatedI have 2 WRVS4400N's available to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies View RelatedRecently installed a WRVS4400N router on my home network. Prior to that I was using the wireless built into my FIOS router. I wanted something more secure so I went with the WRVS4400N. I turned off the FIOS wireless and am only using the cisco wireless.
Im having intermittent issues with the wireless. I have many things hooked up to my wireless including a HP printer and a Sonos system. Most of the time if I just open my ipad I cannot see anything else on my network including the printer. If I try to see the Sonos system can cannot, sometimes I can open the app on my iphone and then I can see it.
Sometimes I can see the printer and sometimes I cant. Sometimes when I do see it and then print to it, it will be gone before it even prints.
I don’t seem to have any issues thru the LAN connections.
Also, ive noticed that the wifi is much slower than the old FIOS box.
FYI, when I remove the cisco and fire back up the FIOS wifi I don’t have any problems at all at any time. And its much faster.
I have tried channel 6, 11 and auto. Also turned off IPC and still no change.
I have a gateway to gateway vpn (home-office) working fine for almost an year btw 2 wrvs4400n routers, This morning, the VPN tunnel was down. I clicked "Connect" from the web based interface, but it does not reconnect.
I tried setting up a new tunnel using the VPN setup wizard, but it says it can't connect to the remote router. Which is strange, since I can ping there normally.
I'm having a heck of a time connecting the WRVS4400N VPN to another WRVS4400N VPN. both of the routers have the current firmware version V2.0.2.1: Router 1 is below, and router 2 has the matching configuration with as it should be the local group being that routers local information and the remote crew set up being router ones information. the status is up on both of the routers, but I'm unable to ping the remote gateway or any device behind it.[code]
View 5 Replies View RelatedHardware: WRVS4400N on Firmware version: V2.0.2.1-ETSI
Quick VPN Version 1.4.2.1 on Windows7 Ultimate 64bit.
QuickVPN Client stopps with: Verifying Network.... and "The remote gateway is not responding. Do you want to wait? Yes / No"
Here we go with the log:
2011/10/24 09:09:06 [STATUS]OS Version: Windows 7
2011/10/24 09:09:06 [STATUS]Windows Firewall Domain Profile Settings: OFF
2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF
2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF
2011/10/24 09:09:07 [STATUS]One network interface detected with IP address 192.168.11.106
[code]....
Additional I can ping to dirkle.dyndns.org as well as accessing to the WRVS4400N [URL] The connection map is as following:
Client --> PPPoE DSL Router --> (...INTERNET...) --> NetvigatorGateway ---> WRVS4400N --> HomeNetwork
The NetvigatorGateway is locatet at my home and also distributing IP-TV. For internet it netvigator gateway is set DMZ to WRVS4400N (network 192.168.1.xxx); the WAN IP is assigned to the WRVS4400N and same as on dirkle.dyndns.org. When I connect myself into the netvigator gateway, (network 192.168.8.xxx) i can successfully establish a VPN connection with QuickVPN to the WRVS4400N.But then, what reason ever, I cannot access to 192.168.1.xxx network devices. QuickVPN does not allow me to see the assigned IP as well. This is my issue 2: After the connection is "successfully" established, it does not feel as I am part of the home network....Issue 3 would be: In the company we use CiscoAnyConnect VPN client (Verison 2.4.0202). Is it possible in using this client instead in any later firmware revision?
at our office we have a brand new WRVS4400N with 2.0.1.3 fw preinstalled.In order to make a VPN connection to our cliente, we need to establish an IPSEC VPN with AES-CBC encryption, but in the drop-down list I can only select 3DES.Does v2.0.2.1 fw update include AES-CBC encryption?In negative case, how can we add this type of encryption to the router?
View 1 Replies View RelatedAfter a few months of trouble-free ... the Cisco WRVS4400N V2 stopped working. i have tried to reset by holding the reset button for 30 seconds ... but nothing changes the red DIAG light remains on at all times
i have also tried two different versions of the Firmware Rescue Utility but all i get is "unable to scan"