at our office we have a brand new WRVS4400N with 2.0.1.3 fw preinstalled.In order to make a VPN connection to our cliente, we need to establish an IPSEC VPN with AES-CBC encryption, but in the drop-down list I can only select 3DES.Does v2.0.2.1 fw update include AES-CBC encryption?In negative case, how can we add this type of encryption to the router?
View 1 RepliesHardware: WRVS4400N on Firmware version: V2.0.2.1-ETSI
Quick VPN Version 1.4.2.1 on Windows7 Ultimate 64bit.
QuickVPN Client stopps with: Verifying Network.... and "The remote gateway is not responding. Do you want to wait? Yes / No"
Here we go with the log:
2011/10/24 09:09:06 [STATUS]OS Version: Windows 7
2011/10/24 09:09:06 [STATUS]Windows Firewall Domain Profile Settings: OFF
2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF
2011/10/24 09:09:06 [STATUS]Windows Firewall Private Profile Settings: OFF
2011/10/24 09:09:07 [STATUS]One network interface detected with IP address 192.168.11.106
[code]....
Additional I can ping to dirkle.dyndns.org as well as accessing to the WRVS4400N [URL] The connection map is as following:
Client --> PPPoE DSL Router --> (...INTERNET...) --> NetvigatorGateway ---> WRVS4400N --> HomeNetwork
The NetvigatorGateway is locatet at my home and also distributing IP-TV. For internet it netvigator gateway is set DMZ to WRVS4400N (network 192.168.1.xxx); the WAN IP is assigned to the WRVS4400N and same as on dirkle.dyndns.org. When I connect myself into the netvigator gateway, (network 192.168.8.xxx) i can successfully establish a VPN connection with QuickVPN to the WRVS4400N.But then, what reason ever, I cannot access to 192.168.1.xxx network devices. QuickVPN does not allow me to see the assigned IP as well. This is my issue 2: After the connection is "successfully" established, it does not feel as I am part of the home network....Issue 3 would be: In the company we use CiscoAnyConnect VPN client (Verison 2.4.0202). Is it possible in using this client instead in any later firmware revision?
How to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.
I have a D-Link DSL-320B ADSL2+ Ethernet modem that connects to the internet fine if I am using just 1 computer. However I have bought a Cisco WRVS4400N to enable me to get all of the other computers at home on the network (wired and wireless).
The WRVS4400N picks up a WAN address from the D-Link BUT I just cannot get an internet connection, just "Local" only. I have tried setting it up as a gateway, as a router, upgraded the firmware but it just is not having it. My previous experience with routers has been just to plug em in and let them get on with it. The WRVS4400N is proving very troublesome.
WRVS4400N needs to be manually connected when the power is recycled after power failure. Is there a setting to connect an IPSEC VPN automatically, instead of manually going in to connect the VPN
View 3 Replies View RelatedI need trouble-shooting wireless network connectivity issues that arose recently:We use a Comcast modem and two WRVS4400N's as wireless routers/wireless access points.We recently got our comcast service upgraded to 100/20 and also got rid of our static ip address. As a result (I think there must be a sort of causal relationship here, but I'm not sure what it is) we can no longer connect to the internet using our wireless networks. We can connect to the wireless network, but have "No Internet Access."
View 4 Replies View RelatedWe just purchased the WRVS4400N router with high hopes. For some reason, our ISP provides a connection through L2TP Dynamic for a static IP. I repeat, L2TP Dynamic. Is there anyway to properly configure the router to use such a connection method. I only see L2TP Static, which seems to be the standard method for many routers.
View 1 Replies View RelatedI am having some difficulties using RDP on the LAN of the router. I previously had a Linksys E4200 router, and I was able to RDP from my Win7 computer (192.168.1.139) to my Win2k3 server on the LAN (192.168.1.251) with no issues. However, when I replace the E4200 with the WRVS4400N, the connection will only work for a few seconds.
It is not exclusive to RDP connections on the LAN either... I get a similar error when attempting to connect to computers off site. I could see MTU's being an issue if it was over a VPN connection, but there is no VPN involved in this case.
I would like to connect to the built in accounts on the wrvs4400n from a mac VPN client. I am new VPN and have not found much information on how to establish this connection. Since Linksys seems determined to rely on Quickvpn, and provides no information on what it is actually doing under the hood I can not figure out how to configure any of the VPN clients available, or the built in VPN tools, for OS X (10.4.8). The only information I have been able to find seems to relate to setting up VPN Tunnels, or running a server behind the wrvs4400n and using one of the VPN passthrough options. I would like to connect directly to the built in accounts, how to set this up on a mac?
View 7 Replies View RelatedI used to have a 877w in the same place and same setup as my current 887, this time though the DMT Bits Per Bin just will not populate on ADSL2+ altough it did work when it sync ADSL1 (same line/DSLAM, just came up ADSL for some reason).
View 6 Replies View RelatedI see a lots of problem associated with wirless connectivity with WRVS4400N, with following config
Firmware version - Firmware Version: V1.1.13
Wireless connectivity - G/N Mixed
Auth - WPA2 AES
Everything else default and AUTO,
Problem:The end devices suddenly drop connection. Wired connection works just fine. The DROPPED device can not be reconnected. On MAC I get AUTH time out. I see the SSID being broadcasted from my HTC wireless analyster so radio may not be the problem. I changed to set the speed to G only or N only but not avail. ONLY way to recover from this is rebooting the router.
I have a Cisco WRVS4400N on the latest firmware and I have just had my Virgin internet connection upgraded to the 100Mb. Once i thought it was upgraded i checked with a broadband speed test and it came back as 15Mb download and 5Mb upload. Before i rang Virgin i thought i'd check with a direct connection from my pc straight to the modem. Ran the speed test and it came back as 100Mb download and 5Mb upload. I thought the best thing to do is restore my settings back to factory and its still the same.
View 7 Replies View RelatedI have a Samsung Galaxy 10.1 tablet and have bee trying to connect to my WRVS4400N router with VPN through the "on board" software as well as with the Any Connect software from Cisco. I have no issues at the moment using Quick VPN from my laptop.
When using the Any Connect software I receive the following messages:
Security warning: untrusted certificate
AnyConnect cannot verify the identity of <IP address>. Would you like to continue anyway?
- Certificate does not match the server name.
- Certificate is from an untrusted source.
- Certificate is not identified for this purpose
[Accept] [Details] [Cancel]
If I select accept, the following error is received:
"Error: Connection attempt has failed due to server communication errors. Please retry the connection".
I have tried setting up the on board VPN with the Samsug Galaxy but every attempt has resulted in a time-out of the connection.
For eight months we have not had any problems with our new WRVS4400N (V2.0.2.1) connected to a Verizon/Westell 6500 to provide DSL internet for our network with DHCP on our server... No changes have been made to the router or modem since initial setup; but, then it started -- Our internet connection would drop intermittently. Sometimes every 5 or 10 minutes - sometimes every hour. Verizon has tested the lines which came up ok, then they sent a tech who changed the wire pair coming into the building for the DSL line and retested the lines which again came up ok, then they provided us with a new modem (now a Verizon/Westell 7500). After all that, the DSL still connects then disconnects intermittently. I am now wondering if the issue lies with the WRVS4400N.
View 2 Replies View RelatedWe recently purchased a Cisco ASR1002 router with four on-board Gigabit SFP-style Ethernet ports. However, when I do a "show ip interface brief", I see that there's an extra Gigabit Ethernet port. See the last interface in the following output:
ASR_1002_router#sh ip int b
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 unassigned YES manual down down
[Code].....
On the router itself, in addition to the four Ethernet SFP ports, there are four additional RJ-45 ports. They're labeled "BITS", "MGMT", "CON", and "AUX". I know what the Con and Aux ports are, but what are the Bits and Mgmt ports? And is one of them the Gigabit Ethernet interface that I see listed at the bottom of the output? And if it is, is there anything special about it, or is it just another routed Ethernet port? Can I do something special with it, like out-of-line managment?
I used speed test and got 50 mega bits per second. I tried re downloading tf2 and i was getting 80 kilo bytes, and I am using windows 7. Doesn't 8 mega bits equal 1 mega byte?
View 2 Replies View RelatedI bought a router Cisco WRVS4400N Wireless-N Gigabit Security Router - VPN v2.0 with the intention of using with the QuickVPN Clien for connecting to my home network.My home network is connected to a pre provide by my ISP Thomson and is connected to it but all my main network is controlled by the WRVS4400N, I have forward all the doors, as you can see by the log part below, and by analysing the log you can see that I can get any PING to complete the VPN connection. [code]
View 1 Replies View Relatedrunning cisco VPN client over Windows XP SP 2 64 bits.
I get the error 442 Failed to enable the virtual adapter. I have seen a number of solutions, but can not find solutions or workarounds for Windows XP 64 bits.
Does the Cisco837 router supports 2048 bits certificates?
View 1 Replies View RelatedIs it possible to generate a public RSA key of 4096-bits on an IOS router? We are running 12.4(24)T5. Have been going through some cisco doc and found this:
Cisco IOS 4096-Bit Public Key Support in IOS 12.4(11) and later.
However when I issue the command,crypto ca trustpoint exampleCAkeys, rsakeypair exampleCAkeys ?
it only shows me the maximum of 2048. Am I missing something? Currently our root cert has a public key of 2048 and the routers a key of 1024. The goal is to increase the root cert and our routers cert to 4096-bits. If that's possible.
I know how if u borrow lets say 3 bits u can make 8 subnets but how many usable subnets?
View 2 Replies View RelatedI'm at my brother's house and I'm trying to connect to hs wireless network. I know the password but whenever I try to enter it it gives me a message that says, "The network password needs to be 128bits or 256 bits depending on your network configuration. This can be entered as 8 to 63 characters or 64 hexadecimal characters." From other forums I've looked at it says that I need to get to the router settings page. It gives me an IP adress to paste into the web browser but it doesn't come up as anything. What the heck?
View 4 Replies View Relatedhere comes the incident description: WRVS4400N breaks established VPN session if I am trying to connect to any LAN host via HTTPS.
View 1 Replies View Relatedwhen i type "show interface" command on 1941 router, shows below print. Why 5 minute input-output rate are 0 bits? Can it be a bug?
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
304015 packets input, 151607798 bytes, 0 no buffer
[Code].....
How many bits must be reallocated from host ID to network ID to create 16 subnets?( i did read the discussion on another page and still no clue). For the Class C network address 192.168.10.0 , which of the following subnet masks provides 32 subnets? How many host bits are necessary to assign addresses to 62 hosts ??
View 4 Replies View RelatedSo I have an issue with getting a laptop hooked onto the router signal. The router is a brand spankin new Linksys EA4500 and the laptop is an IBM which is running Win XP (not sure of SP version as it is a customer's comp. at a hotel I run). Anyway, the error message I am encountering is:The network password needs to be 40 bits r 104 bits depending on your network configuration. This can be entered as 5 or 13 ascii characters or 10 or 26 hexadecimal charactersAt first I thought is was my router password since it contained a $ symbol so I changed it to only letters and numbers but still didn't work. I have never encountered this error message on any laptops and no other rooms have been affected.
View 2 Replies View RelatedI do not see 802.1Q tags nor do I see p-bits (COS) in my wireshark captures. My setup is not working and I have no way to verify (sniff) that the 6509 is setting the p-bits to 3. [code]
View 4 Replies View RelatedI have an ASA5505 which provides internet (just internet) for about more than 600 pc/laptops. Can 5505's DHCP support this number?
View 4 Replies View Relatedwho had a WMP300N with the Broadcom 4329 chip (PCIVEN_14E4&DEV_4329&SUBSYS_00601737&REV_01)Since i got my WMP300N all that i got is a really a big headache, since the drivers DOESN'T are meant for Win 7 (x86/x64), and the guys at Cisco/Linksys really are so kind to bring an unstable driver (v6.100) that they claim is for win 7.
i, as same as a ton of users, really get dissapointed because the driver in the cd does not work on win 7 and the 'official updated driver' is useless as well, and in the end lost a lot of time searching almost in the entire internet for a solution, that some pages claim to have, but the info is oudated, or the links are gone.so in a insurmountable-almost-titanic search, i somehow managed to gather all the required files that i'll put at disposition of those like me have a bad time with a supposed to be a pretty good wireless card.
1- bmc 4329 v4.100, this one is the most 'stable' and works pretty well in 32/64bits, it had a modded .inf wich enables a few features that various users will find pretty useful, when the installer prompts a warning about an unsigned driver, you had to allow the installation
2- bmc 4329 5.100, this one is working too on 32/64 bits, i'm posting it because some people got problems with the 4.100 version, however, the 5.100 is a stock unmodded driver, so maybe it will give connection issues.
I planned to install a LMS 4.0.1 on a VMWare server with Windows 2008 R2 64bits.
Is it supported with the "Windows 2008 R2" patch or do I need to order LMS 4.1 version ?
configure my Cisco WRVS4400N wireless router for AT&T dsl.
View 0 Replies View RelatedIs it possible to create VPN between cisco WRVS4400N and EdgeMarc appliance.
View 1 Replies View RelatedI have established a site-to-site VPN from my head office to a remote location. WRVS4400N router is used in the head office and it is in 10.0.1.0/25 private range. RV120W is used in the remote location and its private range is 192.168.0.0/25. We are able to ping and RDP to the head office from the remote location, but unable to do viceversa. A comcast router is also placed before the WRVS440N router at the head office. I need to get communication to both sides through the established site-to-site VPN.
View 1 Replies View Related