Cisco WAN :: Management And BITS Ports On ASR1002
Aug 30, 2011
We recently purchased a Cisco ASR1002 router with four on-board Gigabit SFP-style Ethernet ports. However, when I do a "show ip interface brief", I see that there's an extra Gigabit Ethernet port. See the last interface in the following output:
ASR_1002_router#sh ip int b
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 unassigned YES manual down down
[Code].....
On the router itself, in addition to the four Ethernet SFP ports, there are four additional RJ-45 ports. They're labeled "BITS", "MGMT", "CON", and "AUX". I know what the Con and Aux ports are, but what are the Bits and Mgmt ports? And is one of them the Gigabit Ethernet interface that I see listed at the bottom of the output? And if it is, is there anything special about it, or is it just another routed Ethernet port? Can I do something special with it, like out-of-line managment?
View 1 Replies
ADVERTISEMENT
Jun 30, 2010
How to configure SSH on a ASR 1002 and apply it to the Management Interface?
View 3 Replies
View Related
Jun 4, 2013
Is it possible to use the mgmt port when in rommon mode? I use the Mgmt port when IOS is loaded and it works fine. I reboot the router, issue a break to put it in rommon and have set some variables but my Mgmt port never has link and I cannot ping it from the network. In rommon mode it looks like this:
PS1=rommon ! >
MCP_STARTUP_TRACEFLAGS=00000000:00000000
BOOT=bootflash:asr1000rp1-adventerprisek9.03.07.03.S.152-4.S3.bin,1;
IP_ADDRESS=10.71.50.101
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.71.50.3
BSI=0
RANDOM_NUM=1133006948
RET_2_RTS=13:38:27 EDT Wed Jun 5 2013
RET_2_RCALTS=1370453907
?=0
View 3 Replies
View Related
Feb 29, 2012
It seems like the 4-ports switch in the 2504 can only one port can be used for management VLAN at a time ? I need all 4 ports to be untagged in the managment VLAN.
View 7 Replies
View Related
Jul 1, 2012
We've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?
View 1 Replies
View Related
Jan 19, 2012
at our office we have a brand new WRVS4400N with 2.0.1.3 fw preinstalled.In order to make a VPN connection to our cliente, we need to establish an IPSEC VPN with AES-CBC encryption, but in the drop-down list I can only select 3DES.Does v2.0.2.1 fw update include AES-CBC encryption?In negative case, how can we add this type of encryption to the router?
View 1 Replies
View Related
Feb 18, 2012
I used to have a 877w in the same place and same setup as my current 887, this time though the DMT Bits Per Bin just will not populate on ADSL2+ altough it did work when it sync ADSL1 (same line/DSLAM, just came up ADSL for some reason).
View 6 Replies
View Related
Nov 16, 2012
I used speed test and got 50 mega bits per second. I tried re downloading tf2 and i was getting 80 kilo bytes, and I am using windows 7. Doesn't 8 mega bits equal 1 mega byte?
View 2 Replies
View Related
May 22, 2011
running cisco VPN client over Windows XP SP 2 64 bits.
I get the error 442 Failed to enable the virtual adapter. I have seen a number of solutions, but can not find solutions or workarounds for Windows XP 64 bits.
View 2 Replies
View Related
Oct 16, 2012
Does the Cisco837 router supports 2048 bits certificates?
View 1 Replies
View Related
Aug 31, 2011
Is it possible to generate a public RSA key of 4096-bits on an IOS router? We are running 12.4(24)T5. Have been going through some cisco doc and found this:
Cisco IOS 4096-Bit Public Key Support in IOS 12.4(11) and later.
However when I issue the command,crypto ca trustpoint exampleCAkeys, rsakeypair exampleCAkeys ?
it only shows me the maximum of 2048. Am I missing something? Currently our root cert has a public key of 2048 and the routers a key of 1024. The goal is to increase the root cert and our routers cert to 4096-bits. If that's possible.
View 6 Replies
View Related
Jun 18, 2011
I know how if u borrow lets say 3 bits u can make 8 subnets but how many usable subnets?
View 2 Replies
View Related
Feb 4, 2011
I'm at my brother's house and I'm trying to connect to hs wireless network. I know the password but whenever I try to enter it it gives me a message that says, "The network password needs to be 128bits or 256 bits depending on your network configuration. This can be entered as 8 to 63 characters or 64 hexadecimal characters." From other forums I've looked at it says that I need to get to the router settings page. It gives me an IP adress to paste into the web browser but it doesn't come up as anything. What the heck?
View 4 Replies
View Related
Nov 23, 2010
when i type "show interface" command on 1941 router, shows below print. Why 5 minute input-output rate are 0 bits? Can it be a bug?
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
304015 packets input, 151607798 bytes, 0 no buffer
[Code].....
View 11 Replies
View Related
Jun 30, 2012
How many bits must be reallocated from host ID to network ID to create 16 subnets?( i did read the discussion on another page and still no clue). For the Class C network address 192.168.10.0 , which of the following subnet masks provides 32 subnets? How many host bits are necessary to assign addresses to 62 hosts ??
View 4 Replies
View Related
Apr 24, 2012
So I have an issue with getting a laptop hooked onto the router signal. The router is a brand spankin new Linksys EA4500 and the laptop is an IBM which is running Win XP (not sure of SP version as it is a customer's comp. at a hotel I run). Anyway, the error message I am encountering is:The network password needs to be 40 bits r 104 bits depending on your network configuration. This can be entered as 5 or 13 ascii characters or 10 or 26 hexadecimal charactersAt first I thought is was my router password since it contained a $ symbol so I changed it to only letters and numbers but still didn't work. I have never encountered this error message on any laptops and no other rooms have been affected.
View 2 Replies
View Related
Dec 30, 2009
I do not see 802.1Q tags nor do I see p-bits (COS) in my wireshark captures. My setup is not working and I have no way to verify (sniff) that the 6509 is setting the p-bits to 3. [code]
View 4 Replies
View Related
Feb 11, 2013
I have an ASA5505 which provides internet (just internet) for about more than 600 pc/laptops. Can 5505's DHCP support this number?
View 4 Replies
View Related
Aug 3, 2012
who had a WMP300N with the Broadcom 4329 chip (PCIVEN_14E4&DEV_4329&SUBSYS_00601737&REV_01)Since i got my WMP300N all that i got is a really a big headache, since the drivers DOESN'T are meant for Win 7 (x86/x64), and the guys at Cisco/Linksys really are so kind to bring an unstable driver (v6.100) that they claim is for win 7.
i, as same as a ton of users, really get dissapointed because the driver in the cd does not work on win 7 and the 'official updated driver' is useless as well, and in the end lost a lot of time searching almost in the entire internet for a solution, that some pages claim to have, but the info is oudated, or the links are gone.so in a insurmountable-almost-titanic search, i somehow managed to gather all the required files that i'll put at disposition of those like me have a bad time with a supposed to be a pretty good wireless card.
1- bmc 4329 v4.100, this one is the most 'stable' and works pretty well in 32/64bits, it had a modded .inf wich enables a few features that various users will find pretty useful, when the installer prompts a warning about an unsigned driver, you had to allow the installation
2- bmc 4329 5.100, this one is working too on 32/64 bits, i'm posting it because some people got problems with the 4.100 version, however, the 5.100 is a stock unmodded driver, so maybe it will give connection issues.
View 1 Replies
View Related
Aug 25, 2012
I am going to configure the NATing on ASR1002 and expecing to have near about 1Million nat translation. Will ASR1002 support 1million nat translations ? how many NAT translations are supportable on the ASR1002 ?I am going to configure NAT on ASR1002-5G/K9 U& have FLASR1-FWNAT-RED.
View 1 Replies
View Related
May 29, 2013
Right now I have a ASR1002 running a very old IOS version.Cisco IOS Software, IOS-XE Software (PPC_LINUX_IOSD-ADVENTERPRISEK9-M), Version 12.2(33)XNE, RELEASE SOFTWARE (fc1) asr1000rp1-ipbasek9.02.05.00.122-33.XNE.bin – 25-NOV-2009?
I am looking to upgrade to a newer version.I was wondering if there are any tricks when upgradeing this IOS. Is it as easy as loading the IOS onto the ASR and then changing the bootpath or is there an upgrade path I must follow? Also would there any need for a licence between 2.x and 3.x.
View 2 Replies
View Related
Jan 27, 2011
The loopback of the ASR1002 is 2.2.2.2. When I use a browser to access it, I got the authentication dialog box asking for username/password. I input the information and submit. But authentication box comes back again and ask for the username/password.
The username/password is test okay. But somehow, the web GUI just does not use it.
View 2 Replies
View Related
Feb 5, 2009
Is the GLC-LH-SM SFP compatible with the ASR1002 and how does it differ from the SFP-GE-L adapter?
View 4 Replies
View Related
Mar 11, 2012
We have an ASR1002 with asr1000rp1-adventerprisek9.03.05.01.S.152-1.S1.bin software.I couldn't find any documentation on how to attach an L2 interface, in my case a subinterface with a single dot1q vlan, to a BDI interface.I'm able to create a bridge-domain interface but it's down down.The command bridge-domain on the subinterface url...
View 2 Replies
View Related
Aug 17, 2011
I'm aware ACL's are handled in hardware on the ASR platform but wondered if there was any way to inspect how many hits we get on each line of an ACL on the ASR, I can't seem to find a command to do this.
Using LOG is not possible due to the large number of hits.
View 2 Replies
View Related
Jun 25, 2012
One of our customer just purchased ASR1002 router, they have three internet links from different ISPs and they dont have any remote site, they have three different public IP pool as their respective ISPs. So, is it possible to load balance the internet traffic using all three link on Cisco ASR router ( IOS - Advance Enterprise Services)
View 3 Replies
View Related
Oct 14, 2012
We have a cisco7206 router which is going to be replaced with an ASR1002 router. The 7206 has some interfaces in a BVI-group - the config of which i am trying to translate over into IOS XE (which runs on the ASR1002). How to translate this config from IOS to IOS XE.
View 3 Replies
View Related
Oct 18, 2011
We are having an issue with BGP flapping peer. We have a ASR1002 as Route Reflector and it work fine with all peers except with 2 peers.
View 3 Replies
View Related
Apr 6, 2013
im trying to create a VPN between a Cisco ASA5510 and an ASR1002 when my Loopback interface is The Source IP . [code]
View 1 Replies
View Related
Oct 23, 2011
what command is required to configure ip accounting on an interface?
I would have thought to what is required is on the interface, turn on Ip accounting i.e.
int gi0/0/0
ip accounting
However, there is no ip accounting command within the interface. We are running version Version 15.1(1)S2.
View 6 Replies
View Related
Dec 27, 2011
During the boot ios we found the error messages below. How can i clear this messages?
Missing or illegal ip address for variable DEFAULT_GATEWAY Using midplane macaddr
Missing or illegal ip address for variable IP_ADDRESS
Missing or illegal ip address for variable IP_SUBNET_MASK
View 2 Replies
View Related
Jun 19, 2011
I've inherited a project building an internet connectivity solution for a large corporate. It has its own AS and its own PI space. They are putting in 100Mbit connections from 5 different Tier1's , taking full internet routing from each. Cisco ASR1002's have already been specified and purchased for the job. I'm not familiar with the ASR platform at all - is it up to the job with full routing tables? multiple instances of full tables ? (not likely to put all 5 into one box!)
View 2 Replies
View Related
May 31, 2012
we are using an ASR 1002 for dynamic NAT (with route maps). I do have a Problem with the usage of the NAT pool it self.The total NAT Translations for the pool are:
#sh ip nat stat
[Id: 1] route-map natted-host-01 pool nat-pool-01 refcount 136
pool nat-pool-01: netmask 255.255.254.0
start XX.XX.202.0 end XX.XX.203.255
type generic, total addresses 512, allocated 88 (17%), missee 0
If i now look into the NAT translation Table i do get less entries:
#sh ip nat translations filter map-id dynamic 1 total Total number of translations: 43
Only a deeper look into the QFP gives here the right values:
# sh platform hardware qfp active feature nat data The ouput count matches the values I get if i isue a sh ip nat stat
My question is how is it handled internally.
We do have a problem too, with raising usage of the pool over the time.Once allocated Pool entries are not released after a period of time. And no NAT translation occur for that used IP NAT pool Addresses.
The timer on the device are set:
ip nat translation timeout 300
ip nat translation tcp-timeout 900
ip nat translation pptp-timeout 900
ip nat translation udp-timeout 120
ip nat translation routemap-entry-timeout 900
ip nat translation max-entries 750000
View 1 Replies
View Related