Cisco Infrastructure :: 2811 / 1841 / WIC-1AM-V2 - Setup POTS Dial Connection Between 2 Routers?
Jun 17, 2012
I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware
[code]....
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a
View 5 Replies
ADVERTISEMENT
Jul 11, 2012
I have a big problem with my Cisco 1841 and the WIC-1AM-V2 in Slot 0.I got the task, to test if it is possible, to build up a connection (Dial on Demand Routing) to a remote modem, which is connected to a console port of another Cisco 1841, with the integrated modem card over POTS from the CLI of the router. My router will only dial out to the remote modems and only if its needed.I am connected to the router with the integrated modem card over a console cable on the console port. The remote modem is also connected to the console port of the remote Cisco 1841.
I found out, with my Dialer Profile configuration, it is possible to build up a connection. I configured a dialer list, that specifies that all ip traffic is permitted an interesting for my dialer interface. So a telnet or ping brings up my dialer, which brings up my Async interface. With the "show line" command, I can see that the TTY line, connected with the Async0/0/0 Interface is in use for 5 minutes, because of the "exec-timeout 5 0", which is configured on the remote router. Now the problem is, in this 5 minutes, I can not use a remote telnet on this line with my loopback interface, because the line is already in use and I get a "connection refused". The first telnet I use runs in a timeout, because the remote host is not responding. When I dial out directly from the modem card and not from the CLI with the AT-commands, I get also the connection and with a return i get the login prompt. I will post my actual config, so that you can see maybe a mistake I did or which command I must use, to get a working connection. [code]
View 6 Replies
View Related
Apr 26, 2013
I have 2 Cisco routers , 1841 and 2811 , I need to setup site to site VPN , but i dont now some how it just does not seems to be working ,
Find attached the Configuration along with the
<----- 172.31.1.0/24----- DG:172.31.1.1>Cisco 2811<Dialer1 -----//Internet//----------Dialer1>Cisco1841---< DG:10.236.5.254-------------- 10.236.5.0/24--->
Find attached command executed on each router in the below order
1) show ver
2) Show run
3) show logging
4) show crypto ipsec sa
5) show crypto isakmp sa
Debugging enabled on routers are
1)Debug Crypto Isakmp
2) Debug Crypto Ipsec.
View 2 Replies
View Related
Aug 20, 2012
I am looking to setup a solution for backing up a Metro Ethernet connection on a 2951 using an 1841 and 2 T1's in a Multilink. The Metro E will be primary, and if the BGP peer goes down, I want it to switchover to the 1841. Can it be done and is there an example of the BGP setup to work off of?
View 1 Replies
View Related
Nov 9, 2012
I've moved a Cisco 887 router from a site where it was used to dial up on an ADSL line to a new site where we have a EFM circuit which terminates at a Cisco 1841 router managed by our ISP. I therefore need to re-configure our 887 router to work as a conduit from our servers back to the Cisco 1841 as its gateway.
I have asked from our ISP and they told me that i need to configure the 887 to use IP address 176.35.140.65 255.255.255.248 and its gateway should be 176.35.140.70. That's great advice in theory but I don't know how to configure this correctly
Our internal network is using subnet 192.168.42.XX which will need to be retained for local devices.
View 7 Replies
View Related
Jul 31, 2012
My daughter is on an Army Base in the South Pacific. They have Dial up internet on their home telephone not DSL. They have high speed wireless at the base community center/coffee shop. I will be going there in 9 days to install the dir-615. She has a Dell Desktop with Vista Basic SP1, laptop with XP, IPAD2 and a NOOK Tablet. The dir-615 HVE1 with firmware 5.00na on the bottom sticker. She said she was able to go to web address, login, change the user name and password, started on the wireless configuration and she paniced. My question is basically this. by using a cat5 cable from the desktop to the dir-615 with dialup internet connected can the router be setup using the automatic method as opposed to manual. Our first priority is to be able transfer files to the 2 tablets without being connected to the internet like a switch and secondly If possible go on to the internet from a Tablet or the Laptop. I assume the second option would reuire internet sharing option when setting up the network and performance would be ugly.
Can get I get this router to work this way with just dialup to set it up
View 5 Replies
View Related
Apr 28, 2009
This is only a small portion of our network but my question is, can these 1841 routers handle a 45Meg connection? I thought these routers were designed for T1/E1 type speeds. I know I saw a router performance document somewhere that showed 1841's could handle 38.4MB of traffic and that is only with routing turned on. If anything else is enabled, like access lists, NetFlow or whatever, that number will decrease because of the capacity of the router. Am I correct in these statements? Any document or anything else that shows performance of these routers?
View 14 Replies
View Related
Jun 20, 2012
I use a cisco 2620 voice gateway with a module NM-HDV-2E1-60. Tell me how you look at snmp for Cisco 2620 load E1. For 2811, I found oid 1.3.6.1.4.1.9.10.19.1.1.4
View 4 Replies
View Related
Nov 30, 2011
i trying to set up a terminal server, 2811 with an HWIC-16A und two octo cables. [code] connect and sometimes not. It seems the connection is established but i don't get a prompt von the target device.The target devices are cisco 2811 and cisco catalysts 3560.
View 1 Replies
View Related
Mar 22, 2013
I need to get the latest firmware for a 2811 router but I am unable to download it. What is the best way to get hold of this can I just contact a local Cisco reseller n Monday or is it more complicated than that?
View 2 Replies
View Related
May 4, 2011
I have a Cisco 2811 and a Cisco 1841 and I cannot get these cards to show up. My IOS for the 1841 is c1841-spservicesk9-mz.124-6.T7 and my IOS for the 2811 is c2800nm-spservicesk9-mz.124-17. When I do a "sh diag" the cards come up as: "unknown daughter card WIC module is not supported/disabled in this slot".
So I am guessing I need a different IOS.
View 1 Replies
View Related
Jul 9, 2012
Seeing very strange behaviour my 2811 Router is sitting behind 3650 switch, when the link between switch and router is trunk the router start rebooting itself, to test i changed to access mode then I can see ip address of router on cdp neig de or else not seeing ip address of router.
View 3 Replies
View Related
May 31, 2010
I have Cisco 2811 Router and few days ago my router doesn't work correctly. I checked config and found config-register was changed (0xC502).
HUV_Murun#sh version
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 10-Jan-08 16:35 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
HUV_Murun uptime is 23 hours, 36 minutes
[code]...
Configuration register is 0xC502. What is the meaning of this config-register (0xC502) and how can be changed config ?
View 3 Replies
View Related
Feb 15, 2013
I need to purchase an 64K dial up modem or a 64K dial up external adapter
View 1 Replies
View Related
Jan 24, 2012
I need the temperature oid for cisco 1841 and 2960 switch.
View 1 Replies
View Related
May 6, 2011
I can't find any specific information on the implementation of packet inspection in a zone based policy firewall. In other words, is there a specification or even just a set of values that define the default inspection parameters for all protocols? With DPI I can manage 'some' of the inspection capabilities but I have some fairly rigorous and specific requirements to meet and I need to validate that the IOS ZBFW will meet those requirements. Specifically, I'm interested in HTTP, DNS, and ICMP but all other protocols would be useful as well.I'm working with basic routers; 871's, 2811's, 1841's, etc. The IOS in use in most cases is adventerprisek9-mz.151-3.T.
View 4 Replies
View Related
Jan 12, 2013
I have a cisco1841 router with 32M CF card installed.Now , i want boot a system image larger 32M from usbdisk.First i insert the 128M usb flash disk to the 1841 router and format it, then i can see the device from dir command.Second copy the larger ios image from tftp to the usb disk and successed,i can see the image with " dir usbflash0:" command.Third i use this command "boot system " ,but there is no selection of "usbflash0: " Does the cisco 1841 router boot the system image from usb disk when reboot the router.
View 2 Replies
View Related
May 3, 2011
How i can create dial up connection i don't know to create?
View 1 Replies
View Related
Nov 12, 2011
I am without my connection until repairs are made inthe following week. I am trying to set up netzero with my current equipment, but cannot find the cd for my netgear router WNR1000.
View 1 Replies
View Related
Jul 19, 2011
Is it possible to run both LAN connection and dial-up modem for internet on the same system?
View 11 Replies
View Related
Aug 17, 2012
I use win7 os and samsung e2652 champ duos mobile. When I connect mobile to pc, the dial-up connection not established and show the error 777: the modem on the remote computer is out of order.
View 1 Replies
View Related
Mar 18, 2011
my dial up connection isn't available on my cellphone's wlan
View 1 Replies
View Related
Jan 12, 2011
is it to increaze the broadbandwith by using a double usb-modem dial-up ...i know tha we can use double connection, but not in real time...
View 8 Replies
View Related
Jun 1, 2011
I have been trying to share my dial-up connection from my vista to other system in my ad-hoc network but I always get error code 1061 saying:
Cannot enable shared access. Error 1061: The service cannot accept control messages at this time
View 2 Replies
View Related
Sep 12, 2011
How can I share a dial up VPN Broad band internet connection over wifi i want to share this dial up connection at my laptop over wifi what necessary hardware require to share internet wireless at my laptop.
View 4 Replies
View Related
Oct 3, 2011
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....) I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 1 Replies
View Related
Oct 20, 2011
Can I connect a router to a dial up connection and get wi-fi?
View 2 Replies
View Related
Jul 30, 2012
Our ISP provider made our internet connection a dial up. Last time it automatically connects to internet without putting those username and password. So after they changed it only our server pc have internet. Others don't have. The technician from the isp provider keep telling that the switch(but he keeps telling us its a router dunno why) need to be configure but switches dont need to be configure right?
View 3 Replies
View Related
Apr 6, 2013
How to setup VPN connection,
Head office : fortigate 200b firewall - SSL, IPsec
Branch office: WRVS4400N Wireless-N Gigabit Security Router with VPN
Both side have the public IP.
View 1 Replies
View Related
Sep 20, 2012
We're looking for recommendation of remote controllable PDUs that support a phone line connection for POTS (in case the core router is down and we need to remotely power cycle connected equipment) and RJ45 for control from the network (if the core router doesn't happen to be down).
View 2 Replies
View Related
Jan 25, 2012
My ISP provides IPv6 connectivity in the form of dual stack IPv4/IPv6 with DHCPv6 Prefix Delegation. Using a Cisco IOS-based router I managed to make such a connection by using as a template the Cisco IOS configuration file that my ISP has posted as an example in the following link:
[URL]
The main point on this configuration is a PPPoE connection with:
interface Dialer46
ipv6 address autoconfig default
ipv6 enable
[Code].....
configure this router according the Cisco IOS configuration file I linked on the top in order to have a working IPv6 connection?
View 4 Replies
View Related
Aug 10, 2010
I did upgrade to WiSM from v5.1 to V6 then i see this log %WCP-3-KEEPALIVE_LOST: wcp_controller_server.c:1763 Lost keepalives from Cat 6K Supervisor.
View 6 Replies
View Related
Jul 1, 2011
I Have a Computer Ready for setup as a Server in the LAN Connection:
Windows 7 Professional.
Another 2 Computers for LAN Connection:
1st Computer is a Windows 7 Professional (Connect as LAN)
2nd Computer is also Windows 7 Professional (Must connect using a Wifi D-Link)
Another 2 Computer for LAN Connection:
Windows XP: Must Connect Using LAN port.
1 Computer:
Windows 7 Home Edition: Must Connect Using LAN port
2 Laptops:
1st Laptop is using Windows 7 Ultimate.
2nd Laptop is a Vista.
How to Connect these Computers to the above mentioned computer ready for setup as as Server?
View 1 Replies
View Related
