Cisco Infrastructure :: 2811 Terminal Server Configuration

Nov 30, 2011

i trying to set up a terminal server, 2811 with an HWIC-16A und two octo cables. [code] connect and sometimes not. It seems the connection is established but i don't get a prompt von the target device.The target devices are cisco 2811 and cisco catalysts 3560.

View 1 Replies


ADVERTISEMENT

Cisco :: Configuration Of Terminal Server On 1921?

May 18, 2011

Since Cisco 2511 is out of sale now and Cisco 1900 series are recommended to replace for the purpose of terminal/comm server. How to configure terminal server on HWIC-8A module?

View 3 Replies View Related

Cisco :: 2901 Terminal Server Configuration

May 12, 2012

I have just purchased 2901 with HWIC-16A and 2 CAB-HD8-ASYNC Terminal Server to manage 16 (connect via console) cisco deivces.
 
Plese find attached the config file. I could not find proper docs on setting up this device as a terminal server. I have followed the following link but did not work.
 
[URL]
  
There are 16 Async (0/0/0 - 15) interfaces and also the following lines.
line 2line 0/0/0 0/0/1line 0/0/2 0/0/15
  
How can I connect to other Cisco devices via the terminal router?

usage of above 16 Async interfaces and lines.

View 4 Replies View Related

Cisco WAN :: RV082 Dual Wan Terminal Server Configuration

Jan 31, 2012

I've a RV082 with 2 internet connections.The idea is to permit external connections to my server and if one Internet line falls, automatically switch to the other.
 
We have configured the router in Smart Link backup.We try to connect with WAN1 and WAN2 enabled and all works fine.
 
We try to connect with WAN1 disabled and automatically WAN2 is activated.The problem start here...if WAN1 is activated while there are connections using WAN2, these connections falls!
 
How I must configure the router to permit that active connections are not disconnected from WAN2 even when WAN1 connection come back?

View 1 Replies View Related

Cisco WAN :: 3620 - Router Configuration For Terminal Server

Feb 1, 2011

Any example of router config for a terminal server.In fact I need a configuration for a router with multiple, low speed, asynchronous ports that are connected to other serial devices, for example,modems or console ports on routers or switches.With this router I would like to use a reverse telnet to connect with my devices using the serial connection.I find many examples on the Cisco web site but none with my router hardware configuration.My router is a 3620 router with a 8 port async (NM-8A/S) network module and I would like to use the 8 serial interfaces, each of them connecting a serial device.
 
Here is the show run and show ver :Router#show ver Cisco Internet work Operating System Software IOS (tm) 3600 Software (C3620-I-M), Version 12.3(25), RELEASE SOFTWARE (fc1)Copyright (c) 1986-2008 by Cisco Systems, Inc.Compiled Mon 28-Jan-08 20:16 by alnguyen
 
ROM: System Bootstrap, Version 11.1(19)AA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) Router up time is 1 minute System returned to ROM by reload System image file is "flash:c3620-i-mz.123-25.bin"
[Code]...

View 1 Replies View Related

Cisco :: Terminal Server Disconnect From TS Session?

Jun 2, 2012

What command sequence disconnects you from a TS session? My setup is as followsr1 > TS > 2009-2621XM 2010-3825-R1 2011-3825-R2I can connect from the TS to any of the devices. The issue is that I am telnet'd to r1 and from there telnet'd to the TS. So when I type "Crtl+Shft+6, x" I go directly back to r1 and not the TS. Furthermore if I resume the session on r1 the TS is still connected to whatever session I was in prior to disconnecting. I've experimented with the disconnect and escape characters but I'm at a loss what it is that changes this.

View 4 Replies View Related

Cisco :: TIA-232 Terminal Server With Async Ports

Jul 24, 2012

We have the 16-port (NM-16A) and 32-port (NM-32A) asynchronous (async) network modules which  provides 16 or 32 EIA/TIA-232 (formerly know as RS-232) data terminal equipment (DTE) serial interfaces at speeds up to 134.4 kbps . Few of the interfaces are connected to the console of cisco switches and routers , now we need to know that the remaining  interfaces can be connected to console ports of devices other then cisco Systems to manage them , Will it work with them ?

View 0 Replies View Related

Cisco WAN :: How To Configure 3825 As Terminal Server

Apr 19, 2012

I want to build up cisco 3800 series router as terminal server , i have Asycs 32A module in cisco 3825. Here is show version of device.Do i need to installed any specific IOS in Cisco 3825 device ? how to configure cisco 3825 as terminal server.

View 1 Replies View Related

Cisco VPN :: 5505 - RDP To Terminal Server Failure

May 2, 2012

I am running ASA 5505 release 8.2(4) using a clientless SSL vpn to connect  my assessors to the server via RDP to a Terminal server.  Everything was working fine until last week when we had a Internet outage. During the outage some of the assessors claimed to have accepted a Cisco add-on to get into the site.  once the internet came backup they could not connect to the terminal servers - what would happen is they would click on the link - say OK to connect the clipboard and the screen would pause for a few seconds then right back to the select options page.
 
they can get to other servers (non-terminal servers) but not to the ones they need.   I can recreate the issue by waiting a REALLY long time before replying to a prompt to install an cisco add-on.  I have users that can connect and others than can not.  Also this only seems to affect Internet Explorer 8 and 9  does not affect Firefox

View 1 Replies View Related

Cisco :: Configure 1811 As Terminal Server

May 15, 2012

I've heard that you can configure an 1811 router as a terminal server for remote console work.I have several of them in the lab and would love to try it out.

View 2 Replies View Related

Terminal Services On Server 2008

May 26, 2011

I have rolled out Terminal Services on Server 2008 R2 for a company I used to work for, it worked perfect the users could go home and browse to our web domain and login and use apps straight from the server.there'd be no Microsoft stuff to be accessed just pure Linux Servers but probarbly if users access the online terminal services on Linux they'd be using a Windows PC

View 1 Replies View Related

Sharing :: Printing From Terminal Server

May 11, 2011

Im having some printing issues whenever im working on the terminal server. If I try to print a document out in "landscape", it will print out "portrait", seen though it displays properly in landscape in the print preview. If Im working locally on my PC, it prints out fine.

View 2 Replies View Related

Cannot See The Sharing Printer Through TS (Terminal Server)

Jan 28, 2011

PC-1 connect to printer as local printer but shared for other PC.

PC-2 through TS can see the shared printer. This is OK. But when the printer move and connect to PC-3.

PC-3 connect to the server through TS and want to have print out some document from the server to the printer. But unfortunately the Printer cannot be seen through TS. Even the printer already shared.

View 3 Replies View Related

Cisco :: 2600 Router With 4A/S Module Can Be Terminal Server

Jul 11, 2011

I have a cisco 2600 router with 4A/S module, can it become the terminal server? If yes, which kind of octal cable should I choose to connect to other cisco routers console ports?

View 0 Replies View Related

Cisco :: NM-16A / Embedded Menu Manager For Terminal Server?

Mar 25, 2012

Using EMM as a nice friendly interface for their terminal server (ie router with NM-16A and octal cables)?when I ask the framework to run the following command it gets stuck will a blinking cursor and clear screen
 
<IOSExecCommand>"connect 10.1.1.1 2000"</IOSExecCommand>
 
however removing the port number allows it to connect fine.
 
<IOSExecCommand>"connect 10.1.1.1"</IOSExecCommand>
 
same symptom if iI were to replace connect with telnet

<IOSExecCommand>"telnet 10.1.1.1 2000"</IOSExecCommand>
 
even setting up an iphost does the same ie:

ip host R1 2000 10.1.1.1
<IOSExecCommand>"connect R1"</IOSExecCommand>
 
All of these commands work fine from the # prompt

View 3 Replies View Related

Cisco WAN :: 2901 Terminal Server And Restricting Access

Apr 19, 2011

I have a Cisco 2901 Terminal server with AAA authentication via ACS server.  I create twoaccounts on the acs server, cciesec2011 and vendor.  Both accounts can log into the Cisco 2901 Terminal Server without any issues.  By the way, I am NOT using AAA authorization on the  Cisco Terminal Server.  Once cciesec2011 or vendor accounts are authenticated, theseaccounts can access all the async line on the Cisco Terminal Server.
 
Now I have a new requirements.  I would like to allow cciesec2011, once this account is successfully authenticated, this account has access to ALL async line on the Terminal Server.  The "vendor" account, I want to restrict this account access only to async line 35 (there are 32 async lines available on the Cisco Terminal Server) and nothing else.
 
How can I accomplish without using AAA authorization on the Cisco Terminal Server?Is it possible to use "privlege level" to accomplish this?  if so, how?

View 5 Replies View Related

Cisco Firewall :: ASA 5510 Email And Terminal Server Going Out

Mar 5, 2011

I am having two issues:
 
1. my email going out is working along with internal, but inbound email is not working. My barracuda email filter is 192.168.1.107 and my exchange 2007 is 192.168.1.222 along with this OWA does not work.
 
2. Terminal Services does not work when I try from the home pc in I get server not available or disconnected

Below is my congig

ASA Version 8.3(1)!hostname wsigatewaydomain-name wsystems.comenable password yVSkMxWRc/S396FB encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0 nameif outside security-level 0 ip address 64.XXX.XXX.XXX 255.XXX.XXX.XXXinterface Ethernet0/1 nameif inside security-level 100 ip address 192.168.1.1 255.255.0.0!interface Ethernet0/2 shutdown no nameif no security-level no ip address!interface Ethernet0/3 [Code]....

View 2 Replies View Related

Cisco Firewall :: 2511 How To Access Terminal Server Remotely

Sep 21, 2011

I have verizon wireless router to connect to the internet via FIOS. The public IP on the wireless router is DHCP assigned. I have my home lab with cisco 2511 and octal cables. I would like to be able to access the terminal server remotely via the internet when I'm not in. I'm concerned cause the wireless router is DHCP assigned IP. Even if I have a static IP on the ethernet port of the 2511 connected to the wireless router, I'm not sure if the NAT will work so it can be accessible from the internet.

View 2 Replies View Related

Cisco Infrastructure :: Snmp For 2620 Load E1 For 2811?

Jun 20, 2012

I use a cisco 2620 voice gateway with a module NM-HDV-2E1-60. Tell me how you look at snmp for Cisco 2620 load E1. For 2811, I found oid 1.3.6.1.4.1.9.10.19.1.1.4

View 4 Replies View Related

Cisco Infrastructure :: Getting 2811 Router Latest Firmware?

Mar 22, 2013

I need to get the latest firmware for a 2811 router but I am unable to download it. What is the best way to get hold of this can I just contact a local Cisco reseller n Monday or is it more complicated than that?

View 2 Replies View Related

Cisco Switching/Routing :: 6500 - How To Set Switch On Auto Terminal Server

Apr 22, 2012

I have a switch(6500) with 2 vlans(2 SUBNETS) and from the other side of my network i have 2 terminal servers.

I want to have a VIP in my 6500 switch which i have the 2 vlans and when the first vlan(network) try to connect to the VIP

my switch will forward to first terminal.When the second vlan try to connect to VIP the switch will forward to second terminal.
 
I'd like the switch to decide in wich terminal server will forwared the packet based on source network.
 
I am not sure how i can do this???I use VIP with SLB???I use NAT???PBR?

View 4 Replies View Related

Cisco :: 2600 Terminal Server Can't Connect To 3750 / 3560 Switches

Jul 23, 2012

I have a 2611XM that I am using as a terminal server for my lab setup.  Async is using octal cables.  It works great with routers of all different models, but when I connect a switch of any model, it does not work.  The connectivity LEDs don't even light (they do for the routers).  The switches in question are 3750s and 3560s. 
 
I have tried straight through from the octal cable to the console port of the switch, as well as a rollover with a converter, no luck.  This does seem to be independent of configuration on the console port - even before the console port of the routers were properly configured, I at least had indication of physical connectivity.

View 2 Replies View Related

Network Printers Disappear After Logoff - Logon To Terminal Server?

Feb 8, 2012

I have an annoying problem with networked printers disconnecting/disappearing when TS users logoff. Current configuration is: SQL server (WinSvr 2K8 R2 Std) has printers installed on it (standard TCP/IP Port) and printer is shared, there are also some printers installed on the DNS server and a couple of satellite offices. Users connect to TS servers (WinSvr 2K8 R2 & WinSvr 2K3) printers are connected and work fine until they logoff, when they log on the printers are gone "sometimes some printers are still there!?" I have tried logging onto the server as domain administrator and connecting printers but they won't even stay for administrator (have had this with win7 client machines) and tried directly 'console' at the server. I have looked at the printers on the SQL server and sharing properties, it is stoping printers from coming back at login on TS Note that local (client machines) connecting to the same shared printer from the SQL server don�t have the problem it's just on the TS server.

View 2 Replies View Related

Cisco Infrastructure :: 2811 Router Is Sitting Behind 3650 Switch?

Jul 9, 2012

Seeing very strange behaviour my 2811 Router is sitting behind  3650 switch, when the link between switch and router is trunk the router start rebooting itself, to test i changed to access mode then I can see ip address of router on cdp neig de or else not seeing ip address of router.

View 3 Replies View Related

Cisco Infrastructure :: 2811 - Router Config-register 0xC502

May 31, 2010

I have Cisco 2811 Router and few days ago my router doesn't work correctly. I checked config and found config-register was changed (0xC502). 
 
HUV_Murun#sh version
Cisco IOS Software, 2800 Software (C2800NM-IPBASE-M), Version 12.4(9)T7, RELEASE SOFTWARE (fc3)
Technical Support: [URL]
Copyright (c) 1986-2008 by Cisco Systems, Inc.
Compiled Thu 10-Jan-08 16:35 by prod_rel_team
ROM: System Bootstrap, Version 12.4(13r)T, RELEASE SOFTWARE (fc1)
HUV_Murun uptime is 23 hours, 36 minutes
[code]...

Configuration register is 0xC502. What is the meaning of this config-register (0xC502) and how can be changed config ?

View 3 Replies View Related

Cisco Switching/Routing :: Unable To Login To 2960 Via Console Through Terminal Server

Oct 23, 2012

I have a set-up with multiple C2960 and C3750 switches. All these devices are being managed remotely. So basically I login to C2901, which is used as a Terminal Server,  and reverse SSH to the console of each device. That's - I have assigned an IP to each port of the terminal server so that I can SSH directly to the desired device through via the mapped IP.
 
Now, recently I had to restart couple of switches - one C2960 and C3750. I initiated the reboot via console connection remotely. I could see the device logs for some time and then the logs stopped and there was no reaction from the console irrespective of any command I tried to enter.
 
I tried resetting the line on the terminal server, but that didn't work.
 
Now when I try to SSH the IP mapped to console of that particular device - i dont get any login prompt and there is no effect on device after giving any command. Although i can see the logs on the console session - but cant do anything.
 
I have a second way of connecting the device via inband- management, and checked the device config found it correct. It is same as other devices which are working correctly.
 
Both C3750 and C2960 are behaving exactly same - can see logs on console but see effect of even pressing enter - not getting login prompt as well.

View 4 Replies View Related

Cisco Infrastructure :: 2811 / 1841 / WIC-1AM-V2 - Setup POTS Dial Connection Between 2 Routers?

Jun 17, 2012

I would like to set up a POTS Dial connection between 2 Cisco routers, using the modem card WIC-1AM-V2. I'd like to use this as an out-of-band connection to a remote site, if the primary internet connection fails. So, this setup will only be used in one direction, 1 router placing calls, the other one receiving calls.Here's my config of the receiving router:
 
chat-script dial "" ATZ AT OK "ATX3D T" ATS0=8 TIMEOUT 120 CONNECT C
interface Async0/2/0 description out of band for network no ip address encapsulation slip async mode interactive
line 0/2/0 session-timeout 5 absolute-timeout 10 script connection dial login local modem InOut transport input all escape-character BREAK autoselect ppp stopbits 1 speed 115200 flowcontrol hardware

[code]....
 
This config is working fine, when dialing in via a Windows Hyperterminal Dial connection. After a while of dialing I get the login prompt of the router.Now I want to have a router placing calls instead of a Windows Server. I can't figure out how to tell a router to place calls to a POTS phone number.
 
Receiving router: 2811, WIC-1AM-V2, IOS c2800nm-ipbasek9-mz.124-25a
Calling router: 1841, WIC-1AM-V2, IOS c1841-advsecurityk9-mz.124-25a

View 5 Replies View Related

Cisco WAN :: 2811 - Configuration Of Router And BGP

Nov 8, 2011

I want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
 
What is theoretical and practical approach to configure bgp??
 
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
 
I have to start it from scratch.

View 5 Replies View Related

Cisco WAN :: 2811 - Configuration Of Multiple NAT / PAT

Oct 13, 2011

I have faced configuration of multiple nat/pat  problem.Point is when I paste into router another  nat pool or  nat with route-map or just static  nat  they doesn't work I mean only one of them works.So, I have several connection hardware cisco 2811 latest ios 15.1

1. internet
2. Local host that  must be translated into global local ip addresses be routed
3. vpn  local hosts that must be translated into local global addres

View 4 Replies View Related

Cisco WAN :: 2811 - NAT Configuration Confirmation

May 2, 2013

I have a 2811 router that I need to confirm NAT configurations as expected. I have 2 deviced on the internal LAN that need to access remote resources without PAT. All the other devices are for a guest network with PAT. My interface Fa0/0 is connected to local network (1.1.1.1/23). Fa0/1 is connected to ISP (10.10.10.178/30). Addressable range from ISP of 10.10.10.192/28 (10.10.10.193-10.10.10.206). Internal machine 1.1.1.2 & 1.1.1.3 must connect to a remote server through internet on spacific port numbers.

View 2 Replies View Related

Cisco Infrastructure :: WCCP Configuration On 4507

Jun 16, 2012

I am trying to setup WCCP on our 4507. For some reason I cannot get this to work! The config I have tried is below. I can't figure out
 
ip wccp web-cache group-list IRONPORT-GROUPLIST
ip wccp source-interface GigabitEthernet2/24
!
Interface Vlan160

[Code].....

View 2 Replies View Related

Cisco Infrastructure :: 3700 - Configuration Tool

Dec 15, 2003

Is there any tool or script which will automatically generate scripts for routers, switches. I am configuring 100's of cisco 3700 routers and 3500 switches. I want to be consistent with my configuration . I am looking for script that when u run it, it will prompt you step by step to configure router, and switch and generate router config file. I know aobut cisco autoconfig maker but thats not what i am looking for.

View 2 Replies View Related

Cisco WAN :: Configuration Script Stored On 2811 Router?

Nov 20, 2011

I have several Cisco 2811 ISR Routers that are functioning as CallManager MGCP voice gateways.  These routers have prtial PRI's attached to them which I realize are not supported by Cisco CallManager using MGCP.  The problem is that whenever the router gets rebooted, the configuration under Controller T1 ends up with the improper PRI Timeslots command and I have to go in and manually change it. Solution:  I have developed smal text files for each router that contains all of the commends needed to get the chnage accomplished (you have to shut down things and remove lines elsewhere to be able to change the PRI Timeslots) and I just telnet to the router and cut and paste the commands into the router.However, I would like to store those files on the router in such a way that I could telenet to the router and then either somehow display the file and then copy/paste it in or possible have a file that could be run to make the changes.  That way I could do the job quickly fram anyplace I could telnet to the router and not have to have the text files on the local machine.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved