I want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
I have several Cisco 2811 ISR Routers that are functioning as CallManager MGCP voice gateways. These routers have prtial PRI's attached to them which I realize are not supported by Cisco CallManager using MGCP. The problem is that whenever the router gets rebooted, the configuration under Controller T1 ends up with the improper PRI Timeslots command and I have to go in and manually change it. Solution: I have developed smal text files for each router that contains all of the commends needed to get the chnage accomplished (you have to shut down things and remove lines elsewhere to be able to change the PRI Timeslots) and I just telnet to the router and cut and paste the commands into the router.However, I would like to store those files on the router in such a way that I could telenet to the router and then either somehow display the file and then copy/paste it in or possible have a file that could be run to make the changes. That way I could do the job quickly fram anyplace I could telnet to the router and not have to have the text files on the local machine.
View 1 Replies View Relatedhave remote routers boot and load a config from the flash card. It seems this is possible if the Flash Class is A, according to the Cisco web site using the
boot config flash:<Config file>
where <Config file> is the file on the flash.
Although this can be applied on 2811 routers, they fail to load the file on the flash card. I've since found that this router type has a Class C flash. So the question is, can either:
Is there a similar process for other classes of Flash cards, specifically Class C?
or
The router flash be set as a Class A to support this functionality,
The preferred resolution for this would be the first as there are many remote routers installed a diverse and difficult locations to visit, should a format/rebuild of the flash fail for some reason.
don't ask to list the output of a show boot or show bootvar, neither of these commands work. The Startup/Running config lists the boot config line.
I have a Cisco 2811 Router. I have two VLANS on the router. The first one of course is VLAN 1 and the second one is one that I created from reading everything from this forum.. it is called VLAN 531
On VLAN one I have an IP address of 10.8.1.1 and on VLAN 531 I have an IP Address of 172.16.1.1, now what I can do is this... I can.. from a workstation on the 10.8.0.0 segment, ping 172.16.1.1 and one server on that segment that has an IP address of 172.16.1.50, which is fine, but what I really want to be able to do is ping our email server which is on a 10.21.0.0 segment and I cannot. Any commands on what I would need to do to make this work as I would like the 172.16.0.0 segment to ping any other part of my LAN of my choosing.
Will 2811 Router with 4 switch port module, How to do dual ISP configuration on this router.
View 10 Replies View RelatedI have faced configuration of multiple nat/pat problem.Point is when I paste into router another nat pool or nat with route-map or just static nat they doesn't work I mean only one of them works.So, I have several connection hardware cisco 2811 latest ios 15.1
1. internet
2. Local host that must be translated into global local ip addresses be routed
3. vpn local hosts that must be translated into local global addres
I have a 2811 router that I need to confirm NAT configurations as expected. I have 2 deviced on the internal LAN that need to access remote resources without PAT. All the other devices are for a guest network with PAT. My interface Fa0/0 is connected to local network (1.1.1.1/23). Fa0/1 is connected to ISP (10.10.10.178/30). Addressable range from ISP of 10.10.10.192/28 (10.10.10.193-10.10.10.206). Internal machine 1.1.1.2 & 1.1.1.3 must connect to a remote server through internet on spacific port numbers.
View 2 Replies View Relateddoes cisco 2811 support?if no, can i make it work for BGP?also, i want to know the configuration of bGP for twoo ISPs for link failover.it will be google if u tell me step by step approach for configuring it
View 1 Replies View Relatedi trying to set up a terminal server, 2811 with an HWIC-16A und two octo cables. [code] connect and sometimes not. It seems the connection is established but i don't get a prompt von the target device.The target devices are cisco 2811 and cisco catalysts 3560.
View 1 Replies View RelatedWe have CISCO2811 model with VWIC2-2MFT-T1/E1 module working good over the E1 line. Since it's getting hard to find new model of CISCO2811 we decided to connect new branches with CISCO2911/K9 model (according to migration doc)
My question is can we use 2811's old config file with the 2911 model directly?
I have a laptop with a single physical NIC which I have used the advanced management tools to create two virtual NICs (say vlan 10 and vlan 20) and both are on the same subnet (say 192.168.4.x). One NIC is for normal TCP/IP traffic and one is for broadcast/multicast traffic (I have some custom software that requires this to be the case and works fine on an older laptops with built-in physical NIC and PCMCIA XIRCOM NIC). The dual NIC laptop communicates with a dual NIC server via a Cisco 2811 router (which has a 16 port switch module at the back) and has vlans set up so.
What I want is for the single NIC laptop (with two virtual NICs) to be able to also communicate with the server. Basically, one NIC is for normal traffic and one is for multicast/broadcast traffic. All three machines need to be able to talk to each other using the NIC for normal traffic and both laptops must be able to receive broadcasts from the server. What is the best way to configure the router to handle the trunking/tagging? Most configuration documentation I read has two complete subnets for the two virtual NICs. Note that all three machines use static IPs and are part of a workgroup so no DNS and domain servers etc.
I am having trouble setting up a EHWIC-VA-DSL-A= card on my cisco 2811 running the following the following:c2800nm-adventerprosek9-mz.151-4.M2.bin and C2800NM_RM2.srec.124-13r.T11
My hardware supplier tells me its the right adsl card (have 1 existing working card not the same) but the card will not detect on the system to be configured.is this the right card? am I missing something?
I am using multiple cisco 2811, 3745 routers and 2950,3550 switches if I need to copy running configuration I have to go to each device and say copy run tftp: <address> Is here any way that automatically by schedule one a week or a month configuration copy from all devices to tftp server?
View 2 Replies View RelatedI just bought an additional router for my network and I'm in the process of setting it up.I have however hit a snag with enabling ssh on the device. It is a cisco router 2811 running IOS 15.0 (refer below to my attempts)
View 3 Replies View Relatedhow many extra interface port can be plugged in to the 2811 router ,there are 2 fixed FE port on this router and i have 3 connection i.e one mpls link , one internet link and one sip trunk .. some body confirm me that i can insert module in 2811 ?
View 5 Replies View RelatedHow to replace fan incisco 2811 router in live or down condition?
View 2 Replies View Relatedwhen I got past my current hang up, I marked the thread as answered, so I wasn't sure if I should start another or continue on...
I've tried going through that troubleshooting doc, but I still can't figure this out.
When turning on debug for the 2811, I'm not seeing any thing.
show debug
Cryptographic Subsystem: Crypto ISAKMP debugging is on Crypto ISAKMP Error debugging is on Crypto IPSEC debugging is on Crypto IPSEC Error debugging is on
#show crypto sessionCrypto session current status
[Code].....
I configured Any Connect SSL VPN on Cisco 2811 router. It works perfectly when I lo gin via web and run secure mobility client. However, when I connect directly from the mobility client connection fails. It does not even ask me for username and password.
----------------------------------------------------------------------------------------------------
Mar 7 21:36:47.613: %SSLVPN-5-SSL_TLS_CONNECT_OK: vw_ctx: UNKNOWN vw_gw: VPN_GATEWAY i_vrf: 0 f_vrf: 0 status: SSL/TLS connection successful with remote at
Mar 7 21:36:47.617: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.621: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.745: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.749: WV: Entering APPL with Context: 0x49233618,
[Code]........
--------------------
I have not figured out yet, why mobility client works when launched from the web and why it does not work directly.
I have cisco 2811 router and two ISP copper line. How can configure it as BGP router.
View 11 Replies View RelatedWe currently are using 2811 router for internet Via IPSEC tunnel.Download speed is 30 Mbps and Upload speed is 6 Mbps.
But we are getting not more than 4 Mbps download speed. We did open Tac case and as per Tac 2811 router is not for 30 Mbps.Can any suggest proper model. We need 2 FastEthernet/Gig and one serial port.
I am looking to upgrade a 2811 router to 15.1.2T and see in the release notes that this image is only compatible with the "C Series" older ISR routers? What is a "C Series" ISR and how do I know if I have one?
View 4 Replies View RelatedI need to upgrade a router from a 2811 to a 3945.
2811 has the following modules:
I am using a cisco 2811 router.It is not booting properly.It reboots continously by just decompressing the image repeatedly..
View 2 Replies View Relatedcan a Cisco 2811 router bundle 2 or 4 ADSL lines ? Reason am asking, we need a device that would be able to bundle 2 or 4 ADSL lines from ISP so that we can you it as backup link in-case the company Internet link does down.
View 5 Replies View RelatedI get stuck in one case. One of my customer has two FTTH lines. I have to config PPPoE in routers. In one line I config succesfully, but one line never up. I call to ISP they ask me to config extactly VLAN id 10 in the physical subinterface. But in subinterface there is no command "pppoe-client dial-pool-number". I check the old modem FTTH, they also config VLAN 10 in Wan interface. I tell ISP why we have the same two FTTHs, but two differrent config ways. ISP says because the two line run in two different infrastructure, two different devices. I don't know how to do now? stay in customer side or ISP side. Here is my PPPoE config:
interface FastEthernet0/0
no ip address
duplex auto
[Code].....
I have a Cisco 2811 router with c2800nm-adventerprisek9_sna-mz.124-2.T6.bin as IOS and i wsh to install this HWIC 4port to increase available ports on my router. Wish to know if this is going to work,that is, if i installed it the IOS available will recognise this card
View 4 Replies View RelatedWe have two 2811 router with configured interfaces:
Router1
interface FastEthernet0/0.380 encapsulation dot1Q 380 ip address 192.168.232.18 255.255.255.248 no snmp trap link-status crypto map clientmap!
interface FastEthernet0/0.382 encapsulation dot1Q 382 ip address 10.132.1.126 255.255.255.252 no snmp trap link-status
interface Vlan1 ip address 192.168.5.1 255.255.255.128 ip nat inside ip virtual-reassembly
ip route 0.0.0.0 0.0.0.0 192.168.232.17
ip route 10.132.254.35 255.255.255.255 10.132.1.125
Router2
interface FastEthernet0/0.197 encapsulation dot1Q 197 ip address 192.168.222.2 255.255.255.248 ip nat inside ip virtual-reassembly no cdp enable
interface Vlan1 ip address 192.168.1.1 255.255.255.128 ip nat inside ip virtual-reassembly ip tcp adjust-mss 1452
So my case is: computer from router1's network can ping 192.168.222.2 (router2 -FastEthernet0/0.197 )computer from router2 network can ping 192.168.232.18 (router1- FastEthernet0/0.380),but can't ping 10.132.1.126 (router1- FastEthernet0/0.382).
How can i connect vlan 380 and vlan382.I want the three vlan to see each other.Is this happen with IRB or not?
I am pretty new to the configuration of a DMZ and I have the task of setting one up.I have a Cisco 2811 Router running Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(24)T1, RELEASE SOFTWARE (fc3), 2 FE interfaces.One FE is connected to the WAN, with a loop back interface configured with the public IP for Internet access in the office.The other FE has 2 sub interfaces configured, one for data and the other for voice traffic.Users within the office are configured to use the data VLAN to access the internet through the WAN.
Now we are setting up some new services and we require to have DMZs setup.I want to setup 3 zones now that the different servers would reside in. How can i achieve this using the existing infrastructure I have?I have an idea to create more subinterfaces and assign them to the zones, but I am still not sure how this would play out. I have been on this for the whole day and unable to make significant progress.
I am trying to upgrade a router 2811, the flash has 64 mb and currently has a IOS 32 mb, but require update it with a IOS 37 mb.
What should I do?, I cannot have the two ios in the flash.
I am trying to use GNS to simulate this, but a bit difficult to achieve this. May I know can the Cisco Router handle below requirement? Example Cisco 2811
1) Bandwidth management based on IP Address or Subnet? For example; allocate 1Mbps (CIR) and 10Mbps (BIR) to 172.16.1.10
2) Can the Cisco Router control the inbound and outbound bandwidth?
3) Can you share the sample config?
I have one cisco 2811 router.One cisco 4503 core switch.And one cyberoam UTM.VLAN 16 on router connected to VLAN 16 of core switch.VLAN 3 on router Connected to UTM.VLAN 2 on router connected with Internet Leased line. And one MPLS VPN terminated at Fast Ethernet port.All ports are fast Ethernet Port on router and all Gigabit Ethernet Ports on Core Switch.Now coming to the point, whenever the router becoming inactive the fast Ethernet ports are working but switch module ports not working. and that point we have to reboot the router.
View 2 Replies View RelatedI have a VIC 2Fxs card and it is not getting recognized in the 2811 router. I checked the cisco website and I saw that the FXS card for the 2811 is a VIC2-2FXS. If i were use this, do I insert it in the HWIC port or do I use a Voice 2V module to insert the FXS card and then insert it into the router. Also , is there any other FXS card that can be used apart from the VIC2-2FXS.
View 1 Replies View RelatedIt has been work for a year without problem. We didn't do any change. Recently, we have to reboot thist router to make it work. After the rebooting, the router will work for a while. It could work from few days to a week, and tt stops working again.
View 7 Replies View Related