We currently are using 2811 router for internet Via IPSEC tunnel.Download speed is 30 Mbps and Upload speed is 6 Mbps.
But we are getting not more than 4 Mbps download speed. We did open Tac case and as per Tac 2811 router is not for 30 Mbps.Can any suggest proper model. We need 2 FastEthernet/Gig and one serial port.
I am facing a problem on a 2811 router. The CPU is remaining around 60% and the router throughput is reaching at most 18 MB while according to the data sheet the 2811 maximum throughput is 61MB. I have checked the output interpreter in order to try and figure out the cause of the high CPU and to determine if it is affecting throughput but there are not processes consuming more than 10%. I have attached the show tech-support and the show process cpu history outputs.
View 11 Replies View RelatedI have been trying to find out what the maximum Wan to Lan thruput is for the Linksys Cisco BEFSR 41 Etherfast router..
Have both the version 3 and 4 models and want to deploy them into both 6mb and 12mb DSL networks.. From what I have found the version 1 and 2 have 10mb wan ports and the version 3 and 4 have 10/100mb ports.. There seems to be hardware upgrades as well with the CPU and memory speeds but what they are I do not know for sure.. Found someone stating that they went from a 50mhz CPU to a 166mhz CPU to a possible 220mhz CPU...
I have a 3640a, 3550 and airopoint 350 I use for my home internet connection. I know it's old equipment, but it's all I could afford at the time. Directly plugged into my modem I get about 10 mb/s, plugged into a switch port no greater than 6, and about 5-6 when connected to wireless which is understandable because it's only wireless B. I'm going to downgrade my connection for the time being as I'm paying for excess bandwidth that I'm unable to use, but any more recent, affordable cisco routers that can handle a high speed cable connection? What kind of throughput does the 3550 get? Cisco states a throughput of approximately 45-60mb/s for the 3640a.
View 14 Replies View Relatedif i plug a cisco 880 router in to a 100MB WAN Ethernet circuit what throughput will i get? on cisco site it says 25mb/sec but if it is Ethernet shouldn't it be done in hardware and get the full 100mb/sec?
I know that a 1841 plugged in to a 40MB WAN circuit can match that speed but Cisco site say it only can do E1 speed.
What is the WAN to LAN Throughput of RV042 router with QoS and SPI enable?
Will the RV042 router able to support a 60Mbps down 3Mbps up Internet connection with QoS enable and SPI enable without slowing down the connection?
I am looking to find the correct router for a 50 Mbps Ethernet connectin that is for Internet traffic. It will need to support 50 Mbps throughput, along with routing protocols for BGP, and maybe NAT/ACL's. It most likely will be a used router, in the 2800 series. I'm thinking a 2821 would work, but need to make sure before I pass it on to the customer. They currently have a 3660 they were thinking of using, but I think it would be too weak, and probably only pas 30Mbps at the most before it chokes. They are a mini ISP with their own ASN, Tier 3.
View 3 Replies View RelatedI have found recently that Cisco 1905 router is having a throughput of only 10 Mb. But the router is having 2 Gig ports!.My understanding is that throughput is the data packetforwarding done by a router at a time.
What is actually mean by throughput of a router. How the router can handle 1 Gb of data from interfaces at a time?
I recently bought a WRT160NL router. I have a 10/10 Mbps internet connection, but when I am connected via the router it only gives me ~2.5/1 Mbps speeds. Connecting my computer directly to the "wall" results in 10/10 Mbps speeds. I have tried connecting to the router both wireless and by wire, it makes no difference. The internal wired and wireless speeds are fine, as I have copied files over the internal switch and via the wireless network at relatively high speeds. I have not fiddled with any connection settings except creating a few permanent DHCP leases.
View 6 Replies View RelatedI have a E4200 V1 with 1G internet connection, when i connect my PC, with a cat6 cable, directly to the modem the download speed can upto 800Mbs, but when i connect through E4200 to the modem it down to 100Mbs.
View 1 Replies View Relatedjust upgraded my internet to 150/10 but with speedboost DL speeds hit 250 mbps. I currently have a e3200 and it tends to max out at 110mbps, any router recommendations that will support the full 250?
View 18 Replies View RelatedI have a E2500 connected via LAN to my network via a switch or hub through a sonic wall and into the modem out to the internet. The problem is that I am only getting +/- 5Mpbs Down and +/-7 Mbps up through the router.
If I connect my computer to the network with out going through the router my speeds are more in the range of +/-28 Mbps down and 16Mbps up. I have been working with Linksys support but they have not been able to assist me with this yet! Is there any configuring I should be doing at the firewall or to the router to tell it to open up the port for faster speeds?
How do I find the default throughput supported by the Router 3925E?I need a router that supports 400Mbps line 3900.The 3925E supports? If so, you need to upgrade or add a EHWIC? If so, what can I addto support that throughput?
View 6 Replies View RelatedIs it possible to bond two T1 lines for increased throughput and for possible failover situations? I currently have the second T1 as just a fail over.
View 3 Replies View RelatedI cannot find this info on the cisco site.
View 2 Replies View RelatedI have an E4200 running firmware v1.0.03.Works fine for a period of time (might be hours, might be days) then throughput drops to something in the range of 1-3M when typically I'll see 6-8M (DSL). I can reset the DSL modem, hubs, etc but the problem isn't fixed until I reset the E4200; so I've pretty much narrowed it down to the router.
View 1 Replies View RelatedWhat the Firewall throughput is for the BEFSX41.
View 9 Replies View RelatedI have been running some test to see what I can do for speed to the interenet and NAS drive.I have a NIC card (1394) and the max connection I get is 400 Mbps. The card is suppose to be 10/100/1000 card and E3000 is the same... so why can't I connect at 1000?Max transfer I get to my NAS is 64-80 Mbps. Is there any way I can get this to be faster? I have a 1TB western digital drive attached.If I went with a NAS system like a Synology BYOD system could I get faster speeds for transfers if the NIC on the system was a 10/100/1000?`
View 5 Replies View RelatedI am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.
View 9 Replies View RelatedI'm trying to identify a Cisco router that will give 300+Mbps through a 1Gb WAN port. I think the 1921 can get up to around 300Mbps with the on board RJ45 ports, but are there any other/better suitable models?
There's no need for any other particular functionality or feature set, the routers aren't doing anything fancy or unusual - it's the achieved throughput that's important.
I have a 500Mbps Internet Connecton with fibre and I bought an EA3500 recently. I found the LAN through put degraded by compare connected and not connected with EA3500.all connections are using CAT5e cable with all Gigabit port enabled in PC/ISP Router.
View 9 Replies View RelatedI'm using E4200 (fw 1.0.03) as AP and EDIMAX 6675nD as a client. I can't get over ca 10MB/s data througput even there aren't any other communication loads. Test conditions are: 5GHz band, no other networks in the band, distance 2m without any obstacles, no other data transfers (except the test), data source is NTB on GLAN port of Linksys, data sink is NAS at GLAN port of Edimax, test file is 0.5GB file. The NTB and NAS doesn't seems to be a bottleneck, because NTB connected directly to the Edimax does over 50MB/s. Both the E4200 and 6675nD are (should be) capable of 450Mbit/s @ MCS23. Strange thing is that none of them allows setting of MCS23 in their manual settings. It ends with MCS15. While forcing the E4200 to a specific MCS (in the hidden wireless_advanced menu) the MCS15, 14, 13 and auto give very similar results. The throughput drops by MCS 12 and lower indexed MCSs.The 10 MB/s seems to be a low number.... and (based on internet forums) I'm not the only one fighting the magic number 10MB/s. What is the reason of the ca 10MB/s bottleneck? And the resons why both of the routers are quiet about the MCS16 to 23 schemes in their menus, while their labels aren't?
View 4 Replies View RelatedI've just upgraded to FIOS quantum service. (50 MB down, 25 up). I have a Linksys 2500 connected to the FIOS router. The FIOS (ActionTec) router provides the full advertised speeds with any speed test service I try. But with the 2500 connected to the FIOS router I get download speeds about 3MB. The MTU on the linksys is 1500. It's connected correctly and is running it's own DHCP server. (Why am I doing this? I try to avoid the ActionTec routers, they have broken many services in the past.)The 2500 firmware is up to date. I've tested on the wireless and wired (ethernet) interfaces.
View 2 Replies View RelatedI want to configure BGP but i am finding it very difficult to know BGP as I am new to this concept.
What is theoretical and practical approach to configure bgp??
I have to configure my office router 2811 for two ISPs which will be acting as fail-over.
I have to start it from scratch.
I just bought an additional router for my network and I'm in the process of setting it up.I have however hit a snag with enabling ssh on the device. It is a cisco router 2811 running IOS 15.0 (refer below to my attempts)
View 3 Replies View Relatedhow many extra interface port can be plugged in to the 2811 router ,there are 2 fixed FE port on this router and i have 3 connection i.e one mpls link , one internet link and one sip trunk .. some body confirm me that i can insert module in 2811 ?
View 5 Replies View RelatedHow to replace fan incisco 2811 router in live or down condition?
View 2 Replies View Relatedwhen I got past my current hang up, I marked the thread as answered, so I wasn't sure if I should start another or continue on...
I've tried going through that troubleshooting doc, but I still can't figure this out.
When turning on debug for the 2811, I'm not seeing any thing.
show debug
Cryptographic Subsystem: Crypto ISAKMP debugging is on Crypto ISAKMP Error debugging is on Crypto IPSEC debugging is on Crypto IPSEC Error debugging is on
#show crypto sessionCrypto session current status
[Code].....
I configured Any Connect SSL VPN on Cisco 2811 router. It works perfectly when I lo gin via web and run secure mobility client. However, when I connect directly from the mobility client connection fails. It does not even ask me for username and password.
----------------------------------------------------------------------------------------------------
Mar 7 21:36:47.613: %SSLVPN-5-SSL_TLS_CONNECT_OK: vw_ctx: UNKNOWN vw_gw: VPN_GATEWAY i_vrf: 0 f_vrf: 0 status: SSL/TLS connection successful with remote at
Mar 7 21:36:47.617: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.621: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.745: WV: sslvpn process rcvd context queue event
Mar 7 21:36:47.749: WV: Entering APPL with Context: 0x49233618,
[Code]........
--------------------
I have not figured out yet, why mobility client works when launched from the web and why it does not work directly.
I have cisco 2811 router and two ISP copper line. How can configure it as BGP router.
View 11 Replies View RelatedI am looking to upgrade a 2811 router to 15.1.2T and see in the release notes that this image is only compatible with the "C Series" older ISR routers? What is a "C Series" ISR and how do I know if I have one?
View 4 Replies View RelatedI need to upgrade a router from a 2811 to a 3945.
2811 has the following modules:
I am using a cisco 2811 router.It is not booting properly.It reboots continously by just decompressing the image repeatedly..
View 2 Replies View Related