How do I find the default throughput supported by the Router 3925E?I need a router that supports 400Mbps line 3900.The 3925E supports? If so, you need to upgrade or add a EHWIC? If so, what can I addto support that throughput?
View 6 RepliesI cant find the maximum number of vrf supported on a 3925E ?
View 1 Replies View RelatedI was searching a lot , but I couldn't find any good example, how to configure DHCP server for our wireless clients on Cisco Autonomous AP. I'm looking for example how to configure Dot 11 radios and BVI interfaces.
I have no problem to configure DHCP server on BVI 1 and VLAN 1 ( native VLAN ) interfaces, but there is a problem with other BVI's and VLANs. Maybe this feature isn't supported? Maybe DHCP server feature is supported to work just with default BVI and native VLAN?
I just received a 887W and would like to setup using the SDM.I don't know and cannot find the default IP.
View 7 Replies View Relatedi looked but didn't find anything. I'm looking for a configuration guide, similar to the ASA Configuration Guide, that that can provide documentation on how to configure a Cisco 3925e router. I have my CCNA and a fair amount of real world experience configuring routers but ultimately what I am looking for is guidance on how to configure BGP on this beast. I learned a great deal about ASAs by running through the ASA Configuration Guide and I am hoping to do the same with the 3900 series ISRs.
View 5 Replies View RelatedI have an LMS 4.0.1 server (on Windows 2008 R2) with all the LMS and device updates applied that fails when trying to do an Inventory Collection on a Cisco 3925E router. The router is running IOS Version 15.1(1)T2. This device is apparently supported according to:
[URL]
Some 'show ver' info:
Cisco IOS Software, C3900e Software (C3900e-UNIVERSALK9-M), Version 15.1(1)T2, RELEASE SOFTWARE (fc1)
ROM: System Bootstrap, Version 15.1(1r)T2, RELEASE SOFTWARE (fc1)
System image file is "flash0:c3900e-universalk9-mz.SPA.151-1.T2.bin"
Cisco CISCO3925-CHASSIS (revision 1.0) with C3900-SPE200/K9 with 689152K/293888K bytes of memory.
'show inv':
NAME: "CISCO3925-CHASSIS", DESCR: "CISCO3925-CHASSIS"
PID: CISCO3925-CHASSIS , VID: V02, SN: FGL152610R8
[Code]....
what my IP address, my subnet mask, and what my default gateway is. I have tried typing "ipconfig" into CMD but then I only got up 100 boxes saying "Permissionisconnected"
View 12 Replies View RelatedI just switched internet providers and i have wireless, since then, my boyfriends laptop is having problems staying connected to the internet. the desktop and my laptop stay connected his doesnt. it will say connected or limited access but i cant get a webpage or when i do its internet explorer cannot find page.System Info Utility version 1.0.0.1[CODE]
View 14 Replies View RelatedI found a new bug in cisco IOS 15.1(4)M3 when running EEM script with syslog event detector.If system logging performed using the "logging discriminator" and run concurrently EEM script with syslog event detector, then Cisco router crash and goes to reboot.
Cisco ISR G2 3925E.
Region : SpainModel : TD-W8968Hardware Version : V1Firmware Version : got an ADSL connection with Movistar Spain, static IP. When I configure the TD-8968 all works well, it syncs but does not connect to internet. When I diagnose the connection the modem pass tests at ATm level but is not able to find the default gateway. I got another modem (the one to be substituted with the 8968) that it works with the configuration I am triying to use. Is there some step I am missing or is the modem faulty?
View 1 Replies View Relatedterms of Performance for 3925, 3925E and 3945.
didn't see much different between 3925 and 3925E except an additional port.
I just installed a new ISR G2 3925e (spe200 integrated) in a VPN environment it works well but I lost latency (it adds around 8-10 ms in the VPN) because of " IPsec packet batching" :Queues multiple packets at the interrupt service routine level after being processed by crypto engine Reduces interrupt context switching by allowing one crypto interrupt for multiple crypto packetsIt's not very good specaly if you tunnel ToIP and/or video streamsI'm trying to find a solution how to disable it without impact other things or is there something planned soon to improve itfyi I use IOS c3900e-universalk9-mz.SPA.151-4.M.bin
View 3 Replies View RelatedWe currently are using 2811 router for internet Via IPSEC tunnel.Download speed is 30 Mbps and Upload speed is 6 Mbps.
But we are getting not more than 4 Mbps download speed. We did open Tac case and as per Tac 2811 router is not for 30 Mbps.Can any suggest proper model. We need 2 FastEthernet/Gig and one serial port.
I have been trying to find out what the maximum Wan to Lan thruput is for the Linksys Cisco BEFSR 41 Etherfast router..
Have both the version 3 and 4 models and want to deploy them into both 6mb and 12mb DSL networks.. From what I have found the version 1 and 2 have 10mb wan ports and the version 3 and 4 have 10/100mb ports.. There seems to be hardware upgrades as well with the CPU and memory speeds but what they are I do not know for sure.. Found someone stating that they went from a 50mhz CPU to a 166mhz CPU to a possible 220mhz CPU...
I have a 3640a, 3550 and airopoint 350 I use for my home internet connection. I know it's old equipment, but it's all I could afford at the time. Directly plugged into my modem I get about 10 mb/s, plugged into a switch port no greater than 6, and about 5-6 when connected to wireless which is understandable because it's only wireless B. I'm going to downgrade my connection for the time being as I'm paying for excess bandwidth that I'm unable to use, but any more recent, affordable cisco routers that can handle a high speed cable connection? What kind of throughput does the 3550 get? Cisco states a throughput of approximately 45-60mb/s for the 3640a.
View 14 Replies View Relatedif i plug a cisco 880 router in to a 100MB WAN Ethernet circuit what throughput will i get? on cisco site it says 25mb/sec but if it is Ethernet shouldn't it be done in hardware and get the full 100mb/sec?
I know that a 1841 plugged in to a 40MB WAN circuit can match that speed but Cisco site say it only can do E1 speed.
What is the WAN to LAN Throughput of RV042 router with QoS and SPI enable?
Will the RV042 router able to support a 60Mbps down 3Mbps up Internet connection with QoS enable and SPI enable without slowing down the connection?
I am looking to find the correct router for a 50 Mbps Ethernet connectin that is for Internet traffic. It will need to support 50 Mbps throughput, along with routing protocols for BGP, and maybe NAT/ACL's. It most likely will be a used router, in the 2800 series. I'm thinking a 2821 would work, but need to make sure before I pass it on to the customer. They currently have a 3660 they were thinking of using, but I think it would be too weak, and probably only pas 30Mbps at the most before it chokes. They are a mini ISP with their own ASN, Tier 3.
View 3 Replies View RelatedI have found recently that Cisco 1905 router is having a throughput of only 10 Mb. But the router is having 2 Gig ports!.My understanding is that throughput is the data packetforwarding done by a router at a time.
What is actually mean by throughput of a router. How the router can handle 1 Gb of data from interfaces at a time?
I recently bought a WRT160NL router. I have a 10/10 Mbps internet connection, but when I am connected via the router it only gives me ~2.5/1 Mbps speeds. Connecting my computer directly to the "wall" results in 10/10 Mbps speeds. I have tried connecting to the router both wireless and by wire, it makes no difference. The internal wired and wireless speeds are fine, as I have copied files over the internal switch and via the wireless network at relatively high speeds. I have not fiddled with any connection settings except creating a few permanent DHCP leases.
View 6 Replies View RelatedI have a E4200 V1 with 1G internet connection, when i connect my PC, with a cat6 cable, directly to the modem the download speed can upto 800Mbs, but when i connect through E4200 to the modem it down to 100Mbs.
View 1 Replies View Relatedjust upgraded my internet to 150/10 but with speedboost DL speeds hit 250 mbps. I currently have a e3200 and it tends to max out at 110mbps, any router recommendations that will support the full 250?
View 18 Replies View RelatedI have a E2500 connected via LAN to my network via a switch or hub through a sonic wall and into the modem out to the internet. The problem is that I am only getting +/- 5Mpbs Down and +/-7 Mbps up through the router.
If I connect my computer to the network with out going through the router my speeds are more in the range of +/-28 Mbps down and 16Mbps up. I have been working with Linksys support but they have not been able to assist me with this yet! Is there any configuring I should be doing at the firewall or to the router to tell it to open up the port for faster speeds?
Is it possible to bond two T1 lines for increased throughput and for possible failover situations? I currently have the second T1 as just a fail over.
View 3 Replies View RelatedI cannot find this info on the cisco site.
View 2 Replies View RelatedI have an E4200 running firmware v1.0.03.Works fine for a period of time (might be hours, might be days) then throughput drops to something in the range of 1-3M when typically I'll see 6-8M (DSL). I can reset the DSL modem, hubs, etc but the problem isn't fixed until I reset the E4200; so I've pretty much narrowed it down to the router.
View 1 Replies View RelatedWhat the Firewall throughput is for the BEFSX41.
View 9 Replies View RelatedI have been running some test to see what I can do for speed to the interenet and NAS drive.I have a NIC card (1394) and the max connection I get is 400 Mbps. The card is suppose to be 10/100/1000 card and E3000 is the same... so why can't I connect at 1000?Max transfer I get to my NAS is 64-80 Mbps. Is there any way I can get this to be faster? I have a 1TB western digital drive attached.If I went with a NAS system like a Synology BYOD system could I get faster speeds for transfers if the NIC on the system was a 10/100/1000?`
View 5 Replies View RelatedI am currently using Netgear FVS338 Routers / VPN Devices in 3 different locations and honestly I am not happy / impressed with them whatsoever.I have been doing some research and came across the Linksys RV042 and RV082 devices that caught my eye. The question is what is the VPN throughput of these devices?I have gone over the website, spec sheets and they only really say the throughput of the LAN Links and not the WAN Links. I currently have very reliable 20Mb+ Synchronous connections between all 3 sites and have not been able to get any good performance out of the Netgear devices and contacting their support is a joke. They can't tell you anything other than it should work or we will swap out the unit. Well if I have 3 of them that have been purchased at all different times I don't believe that they are all having the same issues. What these units 3DES VPN Throughput and will more than likely be purchasing 3 of which ever once suits our needs immediately.
View 9 Replies View RelatedI'm trying to identify a Cisco router that will give 300+Mbps through a 1Gb WAN port. I think the 1921 can get up to around 300Mbps with the on board RJ45 ports, but are there any other/better suitable models?
There's no need for any other particular functionality or feature set, the routers aren't doing anything fancy or unusual - it's the achieved throughput that's important.
this might sound straight forward, but every other pc or console can find and connect to my router.This issue seems to happen about once every few months, sometimes it comes back by itself and reconnects completely fine.
There isn't a "user limit" on our router.Wireless adapter is dell wireless 1505 draft 802.11n wlan mini-card.
Have restarted PC and uninstalled and reinstalled the card.I tried to set the i.p address to static but it says "adapter disconnected" so won't allow me to edit any settings, despite it being able to find neighbour's wireless very easily.
I have a 500Mbps Internet Connecton with fibre and I bought an EA3500 recently. I found the LAN through put degraded by compare connected and not connected with EA3500.all connections are using CAT5e cable with all Gigabit port enabled in PC/ISP Router.
View 9 Replies View RelatedI'm using E4200 (fw 1.0.03) as AP and EDIMAX 6675nD as a client. I can't get over ca 10MB/s data througput even there aren't any other communication loads. Test conditions are: 5GHz band, no other networks in the band, distance 2m without any obstacles, no other data transfers (except the test), data source is NTB on GLAN port of Linksys, data sink is NAS at GLAN port of Edimax, test file is 0.5GB file. The NTB and NAS doesn't seems to be a bottleneck, because NTB connected directly to the Edimax does over 50MB/s. Both the E4200 and 6675nD are (should be) capable of 450Mbit/s @ MCS23. Strange thing is that none of them allows setting of MCS23 in their manual settings. It ends with MCS15. While forcing the E4200 to a specific MCS (in the hidden wireless_advanced menu) the MCS15, 14, 13 and auto give very similar results. The throughput drops by MCS 12 and lower indexed MCSs.The 10 MB/s seems to be a low number.... and (based on internet forums) I'm not the only one fighting the magic number 10MB/s. What is the reason of the ca 10MB/s bottleneck? And the resons why both of the routers are quiet about the MCS16 to 23 schemes in their menus, while their labels aren't?
View 4 Replies View Related