Cisco WAN :: 887W / Cannot Find The Default IP
Oct 15, 2010I just received a 887W and would like to setup using the SDM.I don't know and cannot find the default IP.
View 7 Replies
ADVERTISEMENT
Cisco :: 887w VLan On SSID
Sep 24, 2011The issue that I have is around getting second SSID work on my router! So I have created two Vlans, 30 & 200. Vlan 200 is the native and is associated to SSID "Bitter". This SSID works like a charm however the other Vlan cannot be even pinged from router side the ip that I tried to ping is 192.168.30.1. I have posted the config below. Also i tried to brak wlan-gig into sub interfaces but the IOS does not accept that!
Vlan 30 >>>RadioDot 11 0.30>>>>Gigabit 0.2>>>>bridge group 2
Vlan 200>>RadioDot 11 0.200>>>Gigabit 0.1>>>>bridge group 1 (native Vlan)
Router side:
ip source-route
!
!
!
ip dhcp excluded-address 10.10.10.1
[Code]...
Cisco Switching/Routing :: Getting Configuration For Wireless On The 887w?
May 10, 2012configuration for wireless on the cisco 887w? i would like wireless and wired users on the same vlan if possible i am trying to bring the radio up but it says reset and down and cant get it to bring it up ( i have done vlan1, ip unmbered vlan1 bit and logged onto ap using service-module wlan-ap0 session command) Also is wpa 2 enterprise possible on the cisco 887 w ( if possible i would like it to authenticate with our acs servers on our main site)
View 8 Replies View RelatedCisco WAN :: Cannot Connect To The 887W Router Via Wireless Network
Oct 8, 2011I recently installed a new Cisco 887W router @ my place and everything is working like a charm but the Macbook Air! The devices that are working currently are: iPhone, iPad, HP laptop, Nokia mobile phone.I have checked two Macbook Air so far and both have the same problem with the wireless network! I even manually added the SSID to "Airport Preferred network setting" but still couldn't make it to work!So the issue is the Macbook Air can detect the SSIDs intermittently however when it detects the SSID it doesn not connect to the wireless network and it comes up with the error of "connection timeout". I have used the command "show dot11 association" to see if the Macbook air will be detected on the router side unfortunately that was in vain. The setting that I have on the router under SSID is "guest-mode" i.e. it broadcasts the SSID, security is WPA 2 with AES encyrption.
View 3 Replies View RelatedCisco WAN :: How To Find Default Throughput Supported By Router 3925E
Mar 14, 2012How do I find the default throughput supported by the Router 3925E?I need a router that supports 400Mbps line 3900.The 3925E supports? If so, you need to upgrade or add a EHWIC? If so, what can I addto support that throughput?
View 6 Replies View RelatedHow To Find IP Address / Subnet Mask And Default Gateway
Apr 18, 2013what my IP address, my subnet mask, and what my default gateway is. I have tried typing "ipconfig" into CMD but then I only got up 100 boxes saying "Permissionisconnected"
View 12 Replies View RelatedDefault Gateway Not Available - Limited Access / Cannot Find Page?
Oct 5, 2011I just switched internet providers and i have wireless, since then, my boyfriends laptop is having problems staying connected to the internet. the desktop and my laptop stay connected his doesnt. it will say connected or limited access but i cant get a webpage or when i do its internet explorer cannot find page.System Info Utility version 1.0.0.1[CODE]
View 14 Replies View RelatedCisco Switching/Routing :: 887W - Google Chrome And Updates Not Working
Nov 1, 2012I have cisco router 800 series 887 VAW. WiFi is connected to all my devices through this router, i.e., Windows XP, Vista, Wii, Nexus 7 and HTC Desire S. I can access internet from all these devices. The apps which are already downloaded on my Android devices connect to internet, but the bigest problem is here:
1. Google Play does not connect (on both Nexus 7 and Desire S).
2. Chrome does not work on Nexus 7
3. Nexus 7 fails to check for any system update.
4. Fails to sync accounts.
I tried to contact to the company which gave me this router, but they told the problem lies with my tablet. But the tablet works perfectly fine with others networks and Android phone works fine with 3G and other networks.
TP-Link ADSL2+ Wireless :: TD-8968 Does Not Find Default Gateway?
Jan 5, 2013Region : SpainModel : TD-W8968Hardware Version : V1Firmware Version : got an ADSL connection with Movistar Spain, static IP. When I configure the TD-8968 all works well, it syncs but does not connect to internet. When I diagnose the connection the modem pass tests at ATm level but is not able to find the default gateway. I got another modem (the one to be substituted with the 8968) that it works with the configuration I am triying to use. Is there some step I am missing or is the modem faulty?
View 1 Replies View RelatedCisco Switching/Routing :: 887W Two Ssid Routing Between VLAN?
Oct 4, 2012I created a second VLAN and a second SSID. My problem is that from a PC on the native VLAN 1 I can ping the IP of VLAN 2 192.168.2.254 but I cannot ping any other device that has connected to the second SSID. How do I get routing to work between the two VLAN? I thought it would be automatically setup when I created the second VLAN using Cisco Configuration Professional?
View 3 Replies View RelatedDell :: 1505 Adapter - Can't Find Own Router But Can Find Neighbor's
Jul 12, 2013this might sound straight forward, but every other pc or console can find and connect to my router.This issue seems to happen about once every few months, sometimes it comes back by itself and reconnects completely fine.
There isn't a "user limit" on our router.Wireless adapter is dell wireless 1505 draft 802.11n wlan mini-card.
Have restarted PC and uninstalled and reinstalled the card.I tried to set the i.p address to static but it says "adapter disconnected" so won't allow me to edit any settings, despite it being able to find neighbour's wireless very easily.
Cisco :: AS1 Uses Default Routing?
Nov 18, 2012If AS1 uses default routing, do routers R1-R6 contain separate routing entries for prefixes in AS4 and AS5?
View 16 Replies View RelatedCisco :: ASA 5505 As Default-Gateway?
Mar 28, 2012I am trying to get rid of 2 old 2651xm's and 2 2950's from my CCNA days and want to get into the ASA realm. Can I be able to use the ASA, not only as a security appliance / firewall, but also be able to write the access lists, etc, to be able to use this as my router to push packets to and from my internal LAN to the outside world? I guess I should have stated as this being the front end device to my network, just after my DSL Cable modem, that is..and being the only device. I am trying to have this as my main router /firewall solution and then I have an old Linksys router I will pipe off one of the L2 ports to have an AP for my wireless devices? Is this a real solution an ASA can provide?
View 2 Replies View RelatedCisco :: Leak Default Route To VRF?
Jul 1, 2012I want to leak default internet route to CE VRF as common service.Since we having two ASBR, can I point next hop to PE itself instead of either of the ASBR?I tried to point NH to loopback of the PE itself but it failed.
View 6 Replies View RelatedCisco :: Changing ARP Timer From Its Default Value
Jul 19, 2011how to change the ARP timer in CISCO. I know how to change th mac-address aging timer, but can't seem to find any documents on how to change the ARP timer from 4 hours.
View 2 Replies View RelatedCisco :: Cannot Ping Default Gateway From R2 To R
Feb 13, 2013i'm having problem to ping succesfully default gateway on Router1 from Router2. Basically i can: - ping from R1 the serial interface on R2 and default gateway on R2 - telnet from R1 to R2 - ping from R2 to serial link on R1, BUT I CANNOT ping default gateway from R2 to R1 Below is the photo showing topology and running configuration on both routers
View 2 Replies View RelatedCisco WAN :: 881 Default Ip Configuration For Startup
Nov 19, 2012don't have an option to connect a console cable to my cisco router. The usb to serial converter will not work in windows7 only on XP.have physical access to my 881 Cisco Router. If I remember correctly these routers have a default ip address. This router is brand new, out of the box. I am thinking I can access it with the correct IP via network instead of console.
View 7 Replies View RelatedCisco WAN :: Can't Use ASA5505 As Default Gateway For LAN
Mar 16, 2011We have a network consisting of a central site and a few remote offices. The sites are all connected via MPLS and also have VPNs over ADSL / internet connections as a backup. The remote offices have Cisco 837 routers for the ADSL connections which we can manage but the MPLS routers are managed by the service provider providing the MPLS connections. At the central site we have a Cisco 891 for the the MPLS connection (which we manage) and a Cisco ASA5505 for the backup VPNs.
In order to implement failover from MPLS to VPN in the event of any MPLS line going down I have tried to use ip sla monitors and tracked objects on the 891 as per Cisco's documentation. The problem that I am finding is that I can't set the number of ICMP echo failures required before the tracked route is dropped. Whenever the ip sla monitor fails to get a response the tracked route is dropped immediately. This is too sensitive as packets are occasionally dropped which results in the routes bouncing back and forth between MPLS and VPN too frequently (disconnecting users in the process).
I have tried different threshold types and values, tried configuring ip sla monitor reaction-triggers (although I don't understand what little documentation that I can find on this) and have even looked at event manager. I have been working on this for a few weeks now and am getting nowhere.
The Cisco ASA5505's implementation of ip sla monitor is much better in that it is possible to specify the number of packets but unfortunately we can't use the ASA as the default gateway for the LAN as the asymmetrical routing that occurs does not work with the firewall function of the ASA.
Any issue with ip sla monitor on IOS and managed to get it working?
Cisco WAN :: Default Line 2 In 1941?
Mar 11, 2012I was wondering about the folling witch i found in a Cisco 1941 running config
View 2 Replies View RelatedCisco WAN :: BGP 300 - Default Route Maps
Sep 3, 2011I'm working on a practice lab and am having the following issue. I have a customer router connected to two different ISP routers. Each ISP router must advertise a default through BGP to the customer and one of the default routes must be preferred over the other. Given if the preferred route interface is shut down the other default route is inserted into the routing table and when the preferred default route interface it turned back on that path is used again. The catch is I cant alter the customer router only the the two ISP devices. I tried doing some route maps but I'm lost. I have deleted all my route maps and have posted the BGP portion of the ISP routers.
router bgp 300
no synchronization
bgp log-neighbor-changes
[Code]....
Can't Connect To Default 192.168.1.1 Or 192.168.0.1
Jan 3, 2013I'm in student halls where the internet connection they provide is via ethernet cable. I've read somewhere that if I hook up a router I should be able to set up wireless - so I got a relative's old router and hooked it up. Everything is connected and working fine, however, the connection has no security set up whatsoever.I can't connect to the default 192.168.1.1 or the 192.168.0.1 which I believe would take me to the router's settings page (according to the manual) where I could set up a WPA2 password. Also, when I checked router's IP address it actually displays as 109.175.244.193, but I can't connect to this either.My ISP is StudentCom.This is a 3Com OfficeConnect ADSL Wireless 11g Firewall Router.I'm using both a Windows 7 computer and an OSX 10.8.2 MacBook Pro. [code]
View 6 Replies View RelatedThe Default Gateway Is Not Available?
Feb 21, 2013i joined because i keep on having the same problem. i read around the forum a bit before joining and i saw that mcafee was causing the problem for a lot of people. i dont have mcafee so that cant be it several crashes per day. like, literally close to 100 of them.
View 3 Replies View RelatedDefault Gateway Not Available
May 3, 2012Periodically, I drop internet everywhere around my college's campus. I'm literally four feet from a router, but it doesn't seem to matter. I'll disconnect, run troubleshooter, and I'll get the error message saying that the default gateway is not available. My college is designed for Macs, but I'm running Windows 7. My Mac colleagues do not experience problems. The computer works at home and at nearly every other wireless network I've brought it in range of. Specifically, either IBM or Dell.
Dell XPS 15
i7-2720QM
8gb Ram
Windows 7 Home Premium SP 1
540? Something around 500 Nvidia graphics card
Ipconfig results:
Windows IP Configuration
Host Name . . . . . . . . . . . . : George-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
IP Routing Enabled. . . . . . . . : No
[code].....
Default Gateway Is Not Available?
Nov 30, 2011I recently got a new laptop and ever since, the internet goes in and out. Most of the time it is not out long enough to display the no connectivity icon or stop music from streaming but it is noticeable. When I run the troubleshooter it says that the default gateway is unavailable. I tried manually setting the connection information but the same thing keeps happening except the troubleshooter then says that DHCP is not enabled. I've disabled every firewall I can find and updated all the drivers available. Here is my info:[CODE]
View 3 Replies View RelatedCisco :: OSPF NSSA Default Route?
Jan 19, 2013Looking through the SPROUTE course material they state on several occasions that an ABR will announce a default route in to a standard NSSA area, same as a stub area, because LSA5 external routes are not allowed.
View 8 Replies View RelatedCisco :: 1 Mar 1993 Date - Default After Reload
Jul 25, 2012Cisco equipment without RTC defaults to "1 Mar 1993" after the reload. Why this date was chosen?
View 3 Replies View RelatedCisco :: Default - Gateway On Switch Command
Mar 27, 2013I'm really not clear about default-gateway on switch command, not the function but how its works.i have 1 multilayer switch (MLS 1) that have 2 vlan within it, vlan 2 and 100. on vlan 2 i assign ip address of 192.168.1.1 and on vlan 100 is 172.16.1.254. both vlans are up. then under that multilayer switch i added 2 more MLS (MLS 2 and MLS 3), and the links of MLS 2 and 3 to MLS 1 are trunking. and both MLS 2 and 3 have a same vlan with MLS 1. that i assign an ip address on vlan 2 in MLS 2 192.168.1.2 and i set default gateway 192.168.1.1, and i do the same to MLS 3 but the ip address of vlan 2 is 192.168.1.3i already setup the routing protocol on MLS 1 so that vlan 2 could contact vlan 100. but the fact it doesnt work at all, both MLS 2 and 3 cannot contact vlan 100 eventhough that are already have default-gateway setup, is there anything wrong with the configuration ??
View 3 Replies View RelatedCisco :: BGP And Default Gateway 50% Loss Between Hosts
Mar 22, 2013Why it makes problems to use a default route on a BGP-router (cisco 6500 with sup720 3bxl).Only a very few amount of hosts have that kind of problem and the 50% paket loss is only between this hosts. So another host has no loss to any of the affected hosts. looks for me like there is a problem in the CEF-table.The router has a BGP-fulltable. The gateway of last resort is only set for cases like a flapping BGP-route, so that the traffic is sent to a default next hop, because sometimes he knows a better route which isnt flapping.
View 1 Replies View RelatedCisco :: Series 800 Factory Default Restore?
Feb 1, 2013I'm having trouble with an 800 series router. Work has borrowed it to me so i can practice for my icnd2 exam. Only problem is it has a username and password on it. I have been told i can wipe the device and start over. but i cant get in to the user mode or any mode's as i don't have the user name and password. Is there a way of resetting the router back to factory defaults with out logging in to it?
View 2 Replies View RelatedCisco WAN :: 1800 - Factory Default Reset?
Sep 24, 2012My team already bought one 1800 Series router. And they setted some passwor.
Right now i am not able to login. I know the cisco password recovery method to reset the password.
Instead of password recovery method i want to try with total factory default setting.
is there is any method to do factory default without login
Cisco Firewall :: ASA5510 / Default Route With Different AD Value?
Nov 14, 2011Will ASA5510 support default route failover mechanism by giving two different AD value in the route outside command?
View 1 Replies View RelatedCisco Routers :: Default Routing On WRVS4400Nv2?
Nov 14, 2012I have the device configured in Router mode with 2 VLANs. I am able to communicate between the VLANs however my intention is to get VLAN 2 to talk to the internet and that is not working. A caveat is that I am not using the WAN port on this router at all.
The way I intend for this to work is that I have configured a default route on this device to point to a next hop IP in VLAN 1. Even though VLAN 1 is configured on this device the default gateway for this VLAN resides on another device upstream towards the internet connection. That upstream device is providing the DHCP etc for VLAN1. All devices in VLAN1 are able to get to the internet. Even the ones that reside behind this WRVS4400Nv2.
VLAN 2 is only configured on this device and the Default GW resides on this device. This WRVS is configured to be the DHCP server for this VLAN. Even though hosts in VLAN2 can communicate with devices in VLAN1 and vice-versa none of the hosts in VLAN2 are able to reach the internet. A simple ping gives the message "network unreachable from <IP of WRVS-VLAN2>. So it seems like the WRVS is not using the static default route.
I have upgraded the firmware to the latest version V2.0.2.1. Below is a simple diagram of the setup
VLAN-1 |
------- WRVS4400( IF: LAN1 )--------( IF: LAN1 )Generic Router( IF: WAN )---------INTERNET
VLAN-2 |
actually function as a router or is it that router mode is only to disable NAT and it really does not look up its routing table to route pkts out another LAN interface.
Cisco WAN :: AIR-AP521G-E-K9 / Reset To Factory Default In CLI
Jan 22, 2012I have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default
View 1 Replies View Related
