I'm having trouble with an 800 series router. Work has borrowed it to me so i can practice for my icnd2 exam. Only problem is it has a username and password on it. I have been told i can wipe the device and start over. but i cant get in to the user mode or any mode's as i don't have the user name and password. Is there a way of resetting the router back to factory defaults with out logging in to it?
View 2 RepliesI wonder how i can restore my router to its defalt settings if my reset button is broken and the router has lock the mac of my pc. Can i connect the router to my pc and access it from it?
View 7 Replies View RelatedI currently have 2 cisco aironet 1121G access points. Both of which I believe had an image fail during an upgrade from autonomous mode to lightweight mode. I have tried to reset these access points as directed from Cisco's instructions. I have done a reset (amber light on the middle) and a factory restore (red light in the middle) They go through the steps to restore to factory default, however, after what I believe is an attempt to pull a dhcp address before defaulting into 10.0.0.1 ip address, the access point restarts. This is happening to both of them. After they reset and go through the series of memory tests, I am able to get all three solid green lights, they stay lit for just 15 seconds (rather than 5 minutes so that i can load a new image) I am not sure why they are behaving this way. I have tried as many different possibilities resetting with the mode button. There is no console port on this model of access points so i am unable to manage it otherwise.
View 1 Replies View RelatedI have a cisco aironet 1300 series and i need to reset it back to factory default. the directions say push the mode button while the access point is off and then turn it on while the mode button is down.
View 1 Replies View RelatedI am trying to reset my 1522 series lightweight access point to factory default.On the box,there is no any mode button.Actually password is not set to Default and need pasword recovery on this device.If you have any experience on this lightweight access point that let me know.How I reset device to fectory default.
View 1 Replies View RelatedMy wireless adapter isn't recognized on my computer now :( it was working perfectly before. My computer keeps saying there is no driver for my adapter?
View 1 Replies View Relatedmy name is Nathan and I have ran into an issue with my LAN. I recently did a factory restore by pressing F11 at start up due to corrupted Windows files. Now that I have restored my computer, I get a "limited connectivity" to an "unidentified network" I tried all the Windows repair options, I powercycled my modem and my router and I unplugged and replugged my LAN cable.
View 9 Replies View RelatedI found a Cisco 1711 router in our storage room and I want to factory restore it so we can mess around with it or use it as a backup.
I connected a console cable to it and in Hyperterminal on a Windows XP box I want to try the CTRL+BREAK sequence to clear it out. I'm not concerned with the current config or finding the password, I just want to wipe it like it's never been used before.
This is what I get:
System Bootstrap, Version 12.2(7r)XM4, RELEASE SOFTWARE (fc1)
TAC Support: [URL]
Copyright (c) 2003 by cisco Systems, Inc.
C1700 platform with 131072 Kbytes of main memory
[Code]....
I have installed DD-WRT firmware onto my new D-Link DIR-615. It causes some problems and I'd like to re-flash router with orginal firmware. After turning router on with Emergency Room mode and choosing right (as for me) image file I'm getting "Unable to upload the image, please make sure the uploaded file is the correct image." Information.
Firmware downloaded from: [URL]
How can I fix my router? Which firmware file will be correct if not an original?
The ap 3502i has been registered to the wireless controller, but now want to restore the factory settings, repeated after the upgrade or will appear before the registration information of the wireless controller,
View 3 Replies View Relatedwhile configuring my ASA 5505 I changed the IP address range of the internal network. Obviously I made an error because I cannot reach the box neither at the old nor the new address. How can I restore the interface and firewall definitions or reset the box to its initial state ? I found a doc how to reset the password, but not explaining how to restore the complete initial config.
View 10 Replies View RelatedI messed up the IOS on the flash of CISCO881-SEC-K9. On reboot it booted to ROMMON which allowed me to tftp up a working IOS c880data-universalk9-mz.151-4.M3.bin. Unfortunately somewhere in my playing around the default startup configuration factory loaded on the routerhas been erased. I can load a new a config on the device but as I'm using the router to learn its useful to have the original config load when I factory reset the device. What is the factory start up config?
View 3 Replies View Relatedthe ACE 4710 is running 3.2.5 and I need to put it in another environment.Is there a way to reset its settings?
View 3 Replies View RelatedOne of our costomers has a SRW224G4 Switch - which has not any documentation :-(
I do not get onto the switch in any way. I do not have an IP-Address, the default settings for he serial port do not work ... So I cannot reach the device and reset the password like described in: [URL]
Is there any other way to reset the device? I cannot find any reset button.
My team already bought one 1800 Series router. And they setted some passwor.
Right now i am not able to login. I know the cisco password recovery method to reset the password.
Instead of password recovery method i want to try with total factory default setting.
is there is any method to do factory default without login
I have an AIR-AP521G-E-K9 and i want to reset to factory default in CLI.I tried "write erase" but dont work.I have problems with access-list and i want to desactivate access-list that i have created by web GUI.The problems now is that i can not access to my AP, no ping, no web GUI access.Access that i have is only by CLI, but access list is always blockinh all tha traffic trought my AP.How can i desactivate mac filtering, or how can i reset to factiry default
View 1 Replies View RelatedI have another asa 5520 and it is configured. when i do factory default every thing erase. ok. when i enter again it promped for enable password. and it takes my privious password taht i gave in full configuration.
It generally comes no password . Why enable PW dont erase ? why factory default holds my previous password ?
I have a used 1252 wireless AP. I can't get into it. How do I reset to factory default?
View 1 Replies View RelatedWhat is the factory default config on ASA5505 with 8.4.1?
View 3 Replies View RelatedHow to reset a CAPWAP AP3600 to factory default using the AP's CLI and not the controller.
View 2 Replies View RelatedWe need to "reset" a SG200-08P switch back to the factory default settings and noted the "Quick Start Guide" implies the "Reset" button next to the power button doesn't exist and refers the user to the "Cisco Small Business Smart Switch Administration Guide" for instructions. We couldn't find any information related to a "factory reset" in that document either. Pressed the "paper clip button" on the switch but we still can't get in.
View 7 Replies View RelatedAny info on successfully resetting an light weight 1130 AP to the factory settings? I tried the method described in the doc for 1130 on how to reset 1130 AP to the default settings, but it was not successful. I tried shutdown the AP, and plug in the power while press and holding the Mode button for about 3 seconds.This AP has lost it association with the WLC, is there anyway i can reset the AP to factory default and put in the correct IP address again?
View 3 Replies View RelatedI have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
getting step by step procedure to bring an ASA5550 to factory default setting, so that I can configure it from scratch via ASDM
View 3 Replies View RelatedUnable to log in into our new ESW 540 switch because the default User ID and PW was changed. How do i restore the factory default on the switch.Can't get into the switch with CCA or explorer.
View 1 Replies View RelatedI have a 3750G that used to be a Stack Master of a stack comprised of 2 identical switches. Since then, we have removed the stack from production, and I factory defaulted the stack MEMBER and that went fine. I just held the "Mode" button on the front until the lights all lit up and then issued the reload command and the switch came back with no configuration OTHER than the vlan database I issued the "del vlan.dat" command to no avail. I just manually removed all the vlans.
The stack MASTER on the other hand will NOT go back to factory defaults, and will also NOT erase the vlan database. Everything I try will NOT work. I've tried the following
1) Hold mode button & issue a reload after the lights start flashing
2) issue "Write Erase" then issue "reload"
3) issue "Write Erase", then issue "Write", then issue "reload"
4) issue "erase start" then issue "reload" (just in case the "write erase" command is being depriciated or something weird)
5) issue "erase start" then issue "copy run start" then issue "reload"
Is there a special way to reset a StackMaster back to factory defaults?
Im connecting to my firewall through the console port, and need to know how to reset it to factory defaults. I have looked around online and can not see any reference on how to do this.
View 11 Replies View Relatedi have a new 5505 and i have done a few configurations on it. When i try to reset it to the factory settings via asdm i get an error saying it could not be done. I have used config-factory-default using the cli option available in the asdm. I am using asa 8.2 and asdm 6.2. Will erasing the flash reset to factory defaults.
View 4 Replies View RelatedI need to reset my DLink wireless modem all over again, can't get it to recognise the router, so thought that it would need to reset to factory defaut, how can I do this. Tried just hitting reset on the router,but nothing is happening.
View 4 Replies View RelatedMy DIR655 is about a month old, works fine but randomly resets to factory default (loses configuration). Used it to get internet from an existing wired connection with gateway 192.168.0.1, therefore changed Network address of Dlink to 192.168.1.1 to make it work. Every so many days of working ok, it suddenly resets to factory default with no one touching the reset button. Have to restore the configuration from saved file which is a hassle.
Although the DIR655 is connected to a UPS, it shouldn't lose the settings during blackouts right?
I have a (old) 1231 that I would like to reuse, but no one remembers the password. how to recover a password from this model AP or how to reset the device to factory default?
View 1 Replies View RelatedRecently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies View RelatedWhy when I try to reset Cisco ASA 5505 by pressing the button behind the hardware nothing happen? Just via software I can reset it?
I bought the hardware an year ago and I've never used, the problem that I don't have the blue cable and via software connecting to PC doesn't work.