Cisco Routers :: Default Routing On WRVS4400Nv2?
Nov 14, 2012
I have the device configured in Router mode with 2 VLANs. I am able to communicate between the VLANs however my intention is to get VLAN 2 to talk to the internet and that is not working. A caveat is that I am not using the WAN port on this router at all.
The way I intend for this to work is that I have configured a default route on this device to point to a next hop IP in VLAN 1. Even though VLAN 1 is configured on this device the default gateway for this VLAN resides on another device upstream towards the internet connection. That upstream device is providing the DHCP etc for VLAN1. All devices in VLAN1 are able to get to the internet. Even the ones that reside behind this WRVS4400Nv2.
VLAN 2 is only configured on this device and the Default GW resides on this device. This WRVS is configured to be the DHCP server for this VLAN. Even though hosts in VLAN2 can communicate with devices in VLAN1 and vice-versa none of the hosts in VLAN2 are able to reach the internet. A simple ping gives the message "network unreachable from <IP of WRVS-VLAN2>. So it seems like the WRVS is not using the static default route.
I have upgraded the firmware to the latest version V2.0.2.1. Below is a simple diagram of the setup
VLAN-1 |
------- WRVS4400( IF: LAN1 )--------( IF: LAN1 )Generic Router( IF: WAN )---------INTERNET
VLAN-2 |
actually function as a router or is it that router mode is only to disable NAT and it really does not look up its routing table to route pkts out another LAN interface.
View 2 Replies
ADVERTISEMENT
May 2, 2013
I am having trouble with connecting to the Internet through the router. It has worked for 4 years now and all of a sudden it is not working at all. Any direction to getting reconnected. I have an Internet connection directly to the modem, and I can connect and log into the router admin panel, but it will not allow me to access the Internet through the router either wirelessly or by connecting directly to the router. All the lights come on and flash like normal and I have done a factory reset and still nothing.
View 6 Replies
View Related
Feb 24, 2011
Here's what I'm trying to figure out:
My network is set up such that I have a Wireless Network in VLAN 1, which is the primary network that we use. The subnet is 10.5.1.x.
My goal is to set up a completely isolated Guest Wireless Network, however it would work best. What I am trying to do now is I created a seperate VLAN (VLAN 2, IP range 10.5.2.x) and turned on DHCP on the WRVS4400N. However, in the Guest Network, it is always picking up a 10.5.1.x IP which is handed out by the DHCP server (10.5.1.5, Win 2003) and still routing all of the traffic to/from our private network.
Here's What I have set:
Wireless>Security Settings>Guest Network (SSID 2)
Wireless Isolation (between SSID w/o VLAN): EnabledWireless Isolation (within SSID): EnabledSetup>LAN>VLAN 1
Router IP 10.5.1.1, WLAN IP 10.5.1.3DHCP Relay for 10.5.1.5Setup>LAN>VLAN 2
Router IP 10.5.2.1DHCP Enabled for 10.5.2.x subnetDHCP Relay option is grayed out (not sure why)Setup>Advanced Routing
Inter-VLAN Routing: Disabled
Any way to solve this would be fine. I just do not want traffic routing through our internal network. Ideally, if I could get the Windows server to hand out 10.5.2.x addresses, that would be perfect, but I'm not sure how to configure it for such.
View 17 Replies
View Related
Sep 21, 2011
I have a problem connecting SRP541W to my ISP (L2TP). Connection is established, but default routing table is wrong: instead of gateway I see Server IP: [code]
In similar situations other users of my ISP with Cisco routers (IOS) solved this problem by adding command no peer neighbor-route but i can't do it through the WEBgui...
View 3 Replies
View Related
Oct 4, 2009
I have this piece at my home and just realized today that there is a new firmware available on the cisco web page. It has made the device more stable, but the most noticeable improvement is in the UI. Previously it was a linksys for business UI that was pretty much exactly like the consumer products. After the upgrade it is now a Cisco small business UI. I think that this will make the resellers take the products more seriously as a small business piece rather than an upgraded residential product.
View 2 Replies
View Related
Feb 26, 2013
I bought a WRVS400N v2 to be used as an access point. Currently it is hooked up on my switch via a trunk port and is able to communicate with my gateway. Whenever I try to access an IP subnet other then the local IP address of the WRVS, I get a network unreachable error. To fix this for my local networks, I added the appropriate static route to cover my local LANs and that seems to work now. I tried to add route 0.0.0.0/0.0.0.0 using the web interface for internet access, but somehow it does not recognize this as a default route (quad zero!?). Does any know how I can set the default gateway in this router? Maybe, but hopefully not, I have to use the WAN port to create some kind of uplink and use one of the LAN ports to connect using the trunk port and route traffic for the clients over the WAN port .
View 1 Replies
View Related
Mar 18, 2012
Is it possible to send all traffic through site to site VPN using SRP521W (on the other site ASA) ? Lets say, traffic to Internet from branch through HQ - site to site VPN between branch and HQ. I've tried to set up destination crypto policy entry to 0.0.0.0 0.0.0.0 but it's not accepted. Firmware version is 1.01.26 (003)
View 4 Replies
View Related
Apr 11, 2012
I have RV042 on my remote network, i have problems with VPN connection , user can connect to RV042 but only inside IPs that can ping from vpn user.Is it any way to make the traffic from Rv042 will back to RV042 . maybe with nat.. in example below 192.168.5.100 is my lan IP from my DSL dhcp, and 172.27.0.20 ip on remote, traffic not back to my pc/vpn client, what i want is to translate 192.168.5.100 to RV042 LAN ip address
1485: ICMP echo request (len 32 id 256 seq 29) 192.168.5.100 > 172.27.0.20
1486: ICMP echo reply (len 32 id 256 seq 29) 172.27.0.9 > 192.168.5.100
1487: ICMP echo request (len 32 id 256 seq 30) 192.168.5.100 > 172.27.0.20
1488: ICMP echo reply (len 32 id 256 seq 30) 172.27.0.9 > 192.168.5.100
[code]....
View 3 Replies
View Related
Sep 26, 2012
I am trying to set up DDNS for my network. Right now there are only RV180W for DDNS providers (DynDNS, TZO, and 3322).I wanted to use a free DDNS provider, however DynDNS and TZO are now pay only (or only a short free trial via credit card). 3322 seems untrustworthy, as Google is reporting that it is a security risk?Anyway, my question is: "Is there a way I use another DDNS service other than the ones offered by default in my RV180W?"
View 0 Replies
View Related
Oct 30, 2011
I have a WRV210-A V01 (Software: 2.0.1.5) router that when originally purchased I upgraded the firmware to the newest 2.0.1.5. However after the firmware upgrade the router has not worked right since. [I thought maybe the upgrade did not take, and successfully pushed the firmware 3x times]
Everytime you login to the webpage the right-side pane you have to scroll down 3x pages until you can see the settings options. It does that for everypage you visit you have to scroll down 3x pages until you can see the settings.
The wireless is sporadic and dropping connections, and now certain options like changing the "Basic Rate:" from "All' to "Default" does nothing and wont let you change it.
The main issue I have is that certain wireless settings like changing the "AP Isolation:" cause the router to reset back to factory defaults. and even trying to configure the LAN setup also randomly makes the router reset to factory default.
View 1 Replies
View Related
Aug 1, 2012
How to set the default outbound policy as block in access rules of rv220w? I configure my company router RV220W to block all outbound service traffic, just allow outbound service as : http, https, smtp, dns_tcp / udp. it works fine for some hours, the next day, the rules like expired, the https / smtp / DNS service fail to outgoing, only the http is still ok? What happen? Now I just set the default outbound policy as allow, all traffic can go out, but that is meaningless for a firewall device.
View 1 Replies
View Related
Sep 15, 2011
RVS4000 has default firewall rule from ANY WAN -> to ANY LAN with status Allowed. Should that be denied by default, like in RV042 or RVL200?
View 7 Replies
View Related
Jan 28, 2013
Quote from the RV180 manual; 'By default, all access from the insecure WAN side is blocked from accessing the secure LAN, except in response to requests from the LAN or DMZ.'
Does this mean a general access-rule for the firewall blocking all inbound (WAN --> LAN) data is not required?
View 1 Replies
View Related
Feb 20, 2012
I have 2 WRVS4400N routers that were installed at 2 remote locations to provide VPN access to these sites. The routers have been found reset to the factory defaults on three occasions, twice on one of them and once on the other. Both sites are unmanned so no-one is on site to have pressed the reset button, and both routers were set to have remote management disabled. They are running v2013 firmware.
View 3 Replies
View Related
Feb 15, 2009
Recently purchased a RVS4000 Router, which included v1.1.14 firmware. Is it necessary to reset the router to Factory Default settings, after upgrading to v1.2.11, as in most of the other previous upgrades?
View 37 Replies
View Related
Aug 13, 2011
recently got a RV220W and liking all the configuration options.
Although I cannot find where to change the listening port for management? I want it to listen on port 81 instead of 80.
View 5 Replies
View Related
Aug 18, 2011
After a long effort I managed to get my WRVS4400N to work and provide a stable WLAN/LAN and to define all network devices in my home office. It is running the latest firmware (2.0.1).
I created a seperate SSID and a vlan for it (vlan ID is 3 and IP is 192.168.1.xxx while the default vlan IP is 192.168.0.xxx).
My plan is to use that SSID/vlan for the kids and block some bad content for them via the router there.
I want to make a ACL for that vlan but in the computer list option I can only specify ranges in the default VLAN segment (192.168.0.xxx) while in practice I need the 192.168.1.xxx segment.
I can't switch to .0.xxx as some devices are hard wired to be .1.xxx on my network.
View 1 Replies
View Related
Aug 6, 2011
I upgraded the firmware for my WRVS4400N v2 to version 2.0.2.1 firmware, now old and default passwords don't work. I have tried resetting it as well, and the default password does not work.
View 1 Replies
View Related
Jun 24, 2012
I have a 1941 router configured for Policy based routing with two ISPs.Two static default routes configured to point the gateways of respoective ISPs with same metric.But the problem is, packets are going throug the one ISP only while doing traceroute.
N/W connectivity:
ISP1-----> <----------------------> LAN1
| Router |
ISP-------> <----------------------> LAN 2
Below is my configuration :
Current configuration : 5958 bytes
!
! Last configuration change at 05:18:56 UTC Mon Jun 25 2012
!
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code]....
View 26 Replies
View Related
Mar 6, 2012
I have two ISPs. Each is on it's own subnet connected to the 6509 MSFC/Switch. FW1 is on 100.1.100.0/30 and FW2 is on 200.1.200.0/30 subnet. My goal is route all traffice going to the Internet from subnet 10.133.3.0/24 to FW1 and all other subnets across the organization to FW2. I am not sure if I need to use ACL / Static route combo, or just a static routes or ACLS?
View 5 Replies
View Related
Feb 25, 2013
We have two catalyst 3560 switches running c3560-ipbasek9-mz.122-58.SE2.bin They are connected using etherchannel using gi 0/21 - 24 interfaces.
on 3560-1 switch, there isn't any ip-default gateway or ip route configured. It only have 1 interface vlan configured.
on 3560-2 switch, there is ip default gateway configured along with 1 interface vlan.
What i dont understand here is that, i can reach out to other subnets from 3560-1 switch in which the routing is not enabled?
View 4 Replies
View Related
Jan 23, 2013
I had something strange happen to my WRVS440N router yesterday. Our network had crashed for some reason. So I attempted to log into the device to see what was wrong and I was surprised to discover that all of the settings including user name and password had reverted back to factory default.
1. What are all of the possible scenarios that would cause this to happen?
2.Would disconnecting power in the middle of a boot up sequence cause the router to revert to factory settings?
View 1 Replies
View Related
Sep 20, 2012
My network topology is as follows:
Internet <-> Residential Gateway (RG) from ISP (OEM: Pace) [192.168.1.254/255.255.255.0] <-> RV180 [192.168.1.253/255.255.255.0] <-> SG500 switch [192.168.1.250/255.255.255.0] <-> rest of network.
I know this is a cascading LAN-to-LAN arrangement. The cable from the RG to the RV180 is from a LAN port on the RG to a LAN (not WAN) port on the RV180.
I eventually want to segment my network into a few VLANs from the RV180 down. I am aware most people would recommend DHCP on the "primary" router, but the RG is non-VLAN aware, so I figure I need to handle the DHCP off the RV180. At the same time, I have also opted not to do a LAN-to-WAN cascade because I want to retain the ability to configure the RG from the rest of the network and not have to cart a computer over to the RG to do it.
On the RG, I've disabled DHCP, and placed 192.168.1.253 in the DMZ.
On the RV180, I've enabled DHCP and put it in Router mode.
The issue is that I do not have any Internet connectivity. If I allow the computers in the network to receive IP addresses over DHCP, the default gateway that is communicated is 192.168.1.253, which is the RV180. If I configure static IPv4 information on my computers to point to 192.168.1.254, I am able to connect outside, as you would expect.
How can I get the RV180 to pass out DHCP IP addresses, but point to 192.168.1.254 as the default gateway? I thought the solution might be to create a default route (or something). I went to the static routes tab but it wouldn't let me enter 0.0.0.0 as a destination IP to route through 192.168.1.254.
Further down the line, is it possible for both the RG and the RV180 to connect directly to the SG500, along with the other nodes in my network? That way the RV180 only serves to maintain the VLANs and pass out IP addresses via DHCP, instead of having it be the choke through which everything goes through on the way out?
View 1 Replies
View Related
May 12, 2013
Ive changed the IP address of a laptop to connect to the router with IP 192.168.15.1 but now want to change the router IP address from the defaul to another subnet, so that it is accessable with other workstations on the LAN, but I could not readily find the option to set the Ip address on the router.
I'm signed in with user admin.
I also wanted to add addiontal users. The help indicates there is a User List Add Entry option but from the Administration bar, the left hand menu option shows User Management & User Privileges options. On User Management, it is possible to change the 2 default user names, but I wanted to leve them and create new ones.
View 2 Replies
View Related
May 28, 2013
Have a 1921 that has 3 eth connections (1 LAN, and 2 WAN) - I have 2 seperate OSPF processes (2 areas) on the WAN Ints - both upstream WAN's are sending defaults back to the 1921, and the 1921 is sending it's LAN range to them.
I have ip ospf cost 150 set on the "failover" WAN connection interface (Both on the 1921 and upstream), but the 1921 is preferring the default route from the "failover"?
The default routes are both being received by the 1921, but it's preferring the "failover" Int with the ip ospf cost 150 configured?
View 14 Replies
View Related
Mar 24, 2011
ipconfig /all reports one of my three DNS servers as 192.168.1.1. My Default Gateway and DHCP Server are also reported as 192.168.1.1. This is from a recently installed Valet M10 updating an old Linksys router. The Linksys reported the three DNS servers octets independent of the router's ip and other default settings.JK
View 1 Replies
View Related
Dec 25, 2012
Motorola wr850gp wireless router. The default ip is 192.168.10.1. I attempted to use it as a wireless access point and now it is not working at all. I tried connecting the router LAN port to the computer and 192.168.10.1 pulls up nothing.I tried connecting the modem to the WAN port and the LAN port of the router to the PC, but then I have no internet access at all. I tried resetting the router, still nothingAll lights on the router are green. I don't know what the heck is going on?
View 3 Replies
View Related
Jul 18, 2011
recently, i have connected the internet to my PC with cable. Here the problem is , the packets are not receiving in the status bar of internet connection. I have checked in command prompt, the ip address is connecting properly but the default gateway ip address is showing "Request Timed Out" message.
View 1 Replies
View Related
Feb 14, 2013
I am currently setting up a 2800 Series router, and prefer a username/password type authentication rather than a single enable password. To do this, I did:
Router(config)# username <myuser> privilege 15 secret 0 <mypassword>
Router(config)# username2 <myuser> privilege 15 secret 0 <mypassword>
Router(config)# aaa new-model
Router(config)# aaa authentication login default local
This basically does what I want - when I connect to the router through console, it immediately asks me for a username and password. The thing is - as soon as I provide the right credentials, it takes me to USER EXEC mode (the default command mode). Is it possible to change that so that after entering the credentials, I go right into privileged exec mode?
Bonus question: As it is now, I just have no enable password, so when I login with my credentials, I issue "enable" to enter privileged exec mode without it prompting for an additional password. Is it safe to do it this way - having no enable password but requiring a username and password for login?
View 3 Replies
View Related
Oct 3, 2012
I have a RV042 router. The problem that I am having with it is that the DHCP is giving out the wrong Default Gateway and DNS Server. There is no option to change the DHCP server IP on any of the settings pages on the router. I am begining to think that there might not be a way to do it. I see that there is an option for the DNS under the DHCP page but the Public IP that is being handed out is not the one on that page. I also have 2 WAN connections hooked up as well a DSL link and a Cable link (the cable link is the primary one).
The following information is provided in an effort to resolve this issue:
IP of Router 10.0.0.2
IP of DHCP Server (the one that is being handed out):10.0.0.1
IP of DNS (the one that is being handed out): 10.0.0.11
What I want to it be.
IP of Router: 10.0.0.2
IP of DHCP 10.0.0.2
IP of DNS 10.0.0.2
View 3 Replies
View Related
Nov 18, 2012
If AS1 uses default routing, do routers R1-R6 contain separate routing entries for prefixes in AS4 and AS5?
View 16 Replies
View Related
Dec 10, 2012
I just checked that PBR with setting ip default next-hop is not available on cat 3750. Any other way to do dual-homing ISP without this feature?
View 10 Replies
View Related
Jul 16, 2012
We have configured BGP on Cisco Switch 6509E, firewall module on the switch is making nat for all users,but users is not going to internet yet, I do not know hot to configure 6509E to give internet access to users.If I route default route to FWSM,then BGP will not work? If I route default route what is the meaning of BGP then?
I do not want to write static route because BGP should work (4 ISPs redundancy)
How to let users to go out to the internet throug BGP, but nat is being done on the firewall module on 6509, routing is beiing done on 6509,to to configure it?
View 4 Replies
View Related
