Cisco Routers :: WRVS4400NV2 Says No Internet Connection
May 2, 2013
I am having trouble with connecting to the Internet through the router. It has worked for 4 years now and all of a sudden it is not working at all. Any direction to getting reconnected. I have an Internet connection directly to the modem, and I can connect and log into the router admin panel, but it will not allow me to access the Internet through the router either wirelessly or by connecting directly to the router. All the lights come on and flash like normal and I have done a factory reset and still nothing.
View 6 Replies
ADVERTISEMENT
Nov 14, 2012
I have the device configured in Router mode with 2 VLANs. I am able to communicate between the VLANs however my intention is to get VLAN 2 to talk to the internet and that is not working. A caveat is that I am not using the WAN port on this router at all.
The way I intend for this to work is that I have configured a default route on this device to point to a next hop IP in VLAN 1. Even though VLAN 1 is configured on this device the default gateway for this VLAN resides on another device upstream towards the internet connection. That upstream device is providing the DHCP etc for VLAN1. All devices in VLAN1 are able to get to the internet. Even the ones that reside behind this WRVS4400Nv2.
VLAN 2 is only configured on this device and the Default GW resides on this device. This WRVS is configured to be the DHCP server for this VLAN. Even though hosts in VLAN2 can communicate with devices in VLAN1 and vice-versa none of the hosts in VLAN2 are able to reach the internet. A simple ping gives the message "network unreachable from <IP of WRVS-VLAN2>. So it seems like the WRVS is not using the static default route.
I have upgraded the firmware to the latest version V2.0.2.1. Below is a simple diagram of the setup
VLAN-1 |
------- WRVS4400( IF: LAN1 )--------( IF: LAN1 )Generic Router( IF: WAN )---------INTERNET
VLAN-2 |
actually function as a router or is it that router mode is only to disable NAT and it really does not look up its routing table to route pkts out another LAN interface.
View 2 Replies
View Related
Feb 24, 2011
Here's what I'm trying to figure out:
My network is set up such that I have a Wireless Network in VLAN 1, which is the primary network that we use. The subnet is 10.5.1.x.
My goal is to set up a completely isolated Guest Wireless Network, however it would work best. What I am trying to do now is I created a seperate VLAN (VLAN 2, IP range 10.5.2.x) and turned on DHCP on the WRVS4400N. However, in the Guest Network, it is always picking up a 10.5.1.x IP which is handed out by the DHCP server (10.5.1.5, Win 2003) and still routing all of the traffic to/from our private network.
Here's What I have set:
Wireless>Security Settings>Guest Network (SSID 2)
Wireless Isolation (between SSID w/o VLAN): EnabledWireless Isolation (within SSID): EnabledSetup>LAN>VLAN 1
Router IP 10.5.1.1, WLAN IP 10.5.1.3DHCP Relay for 10.5.1.5Setup>LAN>VLAN 2
Router IP 10.5.2.1DHCP Enabled for 10.5.2.x subnetDHCP Relay option is grayed out (not sure why)Setup>Advanced Routing
Inter-VLAN Routing: Disabled
Any way to solve this would be fine. I just do not want traffic routing through our internal network. Ideally, if I could get the Windows server to hand out 10.5.2.x addresses, that would be perfect, but I'm not sure how to configure it for such.
View 17 Replies
View Related
Oct 4, 2009
I have this piece at my home and just realized today that there is a new firmware available on the cisco web page. It has made the device more stable, but the most noticeable improvement is in the UI. Previously it was a linksys for business UI that was pretty much exactly like the consumer products. After the upgrade it is now a Cisco small business UI. I think that this will make the resellers take the products more seriously as a small business piece rather than an upgraded residential product.
View 2 Replies
View Related
Mar 8, 2013
I currently have a Router that is ADSL2 & VPN capable. It currently allows me to work from home and connect to work servers securely. I have used traceroute [URL] in CMD to determine that all web requests/traffic goes through the VPN server rather than just the requests to access files on the VPN server.I don't feel comfortable having all my traffic now go through work servers(the VPN) so I would like to avoid this. I know I have 2 solutions:- Use Split Tunelling on the router where only requests to files on the VPN server will go through the VPN server, all other traffic is not through the VPN. I have heard that this can compromise the whole network as one node is currently 'unsecured' and can affect/compromise the whole network. Is this true?
- Add a second Router that doesn't connect through the VPN. When I finish work I disconnect from the VPN Routers wireless connection and connect through the second routers wireless connection. I would like to take solution 2 because I wont be compromising the whole network but I have some questions:- Is this something you would recommend?
- Is it dangerous? Is it just as compromising as solution 1?
- In Australia we use physical Phone Splitters for our internet physical connection. One side of the splitter connects to a phone line port on the wall. The other side has 2 ports, one for the phone line connection and one for the router/adsl connection. If I have 2 routers I'll need a splitter that has more than 2 ports so I can connect the 2nd router to the internet. Are there Phone Splitters with more than 2 ports and do ISP's allow me to do this?
View 1 Replies
View Related
Feb 8, 2012
I have Verizon fios with a modem that has a build in router. I purchased a secondary router so to separate what devices goes online. Now I did the easy setup wizard and connect the secondary router successfully however there is no Internet connection. Is how can I separate the routers and use the same internet connection.
View 11 Replies
View Related
Feb 3, 2013
I have a Cisco RV120W router with 1.0.4.10 firmware. The router drop the internet connections, freeze/timeout in admin interface randomly. How can I determine that this is the router's fault, or if it's the switch / internet access is causing it?
View 4 Replies
View Related
Apr 8, 2012
Just recently purchased an RVS4000 to take the place of an old NetGear FVS336, which supported multiple NAT translations. It appears that the RVS4000 does not support this, any other models in the small business line support this? I only need this for a backup Internet connection?
View 4 Replies
View Related
Sep 11, 2011
My RV220W is sitting behind a Dynalink RTA1046VW ADSL Modem.
Can't get the RV220W to detect an internet connection through the WAN port. Have got the PPPoE profile set up etc. Have tried the Dynalink in bridging mode, but to no success. Tried the setup wizard.
Firmware is current: v1.0.2.4. The connection is picked up ok through the ethernet ports.
View 5 Replies
View Related
Jul 24, 2011
The connection of the computer before is activating.. after how many days of using,it losses the internet connection.. what is the possible reason for this?
View 1 Replies
View Related
Mar 4, 2011
I have a USB modem connection, and i want to share the connection with two computers and three wireless devices through a sky router. The system OS is Windows 7
View 4 Replies
View Related
Nov 19, 2011
I have the Apple Time Capsule connected to my ISP using PPPoE and it is working just fine creating a wired and wireless network. The IP address of TC is 192.168.1.1 and I have set it's DHCP range between .100 to .200Next, I wanted to add VPN to the router as I live outside the US and wanted to access some services in the US. So I got an ASUS router and flashed it with Tomato firmware.I assigned the ASUS as IP address of 192.168.1.10, connected this it to a LAN port on the Apple and used a DHCP type Internet connection to set it up. I then created a second WiFi Network and gave the DHCP range between .11 to .20Now using any Wi-Fi device, I can connect to either of these networks and browse the web just fine. The ASUS is all setup as a VPN client so any traffic going through the ASUS is through a US based VPN.
View 5 Replies
View Related
Aug 12, 2011
I've noticed recently that my laptop keeps disconnecting from the internet via my router (Thompson Speedtouch ST585v6sl.)The light on the router that shows the connection turns red or sometimes it doesnt light up. However all the other lights stay on, it's just the internet light.It only happens for around 5-10 minutes and then after troubleshooting, disconnecting and reconnecting it's back up.I've scanned my computer for viruses and malware and nothing has come up, this is happening reguarly now about every 30-45 minutes when i'm on my pc.
View 3 Replies
View Related
Mar 5, 2011
i have been having issues with my internet for months now, my router just randomly loses its internet connection over and over everyday. I used to have slow internet with verizon so i changed to comcast and after i changed to comcast this problem started, when i called comcast they said that it has to be interference from an unknown source. I have a Wireless-N 150 Router model WNR1000v2 and it came with a modem. Things i have tried are changing my security to WPA2-PSK[AES] which it saiid would increase my connectivity..did not, i have changed my channel also didnt solve the problem. I have had this problem with 2 different routers and modems so far. And i have 2 desktops and 2 laptops connected to this. 1 desktop is hooked straight into the router and the other 3 are wireless.
View 5 Replies
View Related
Jul 27, 2011
I have recently changed my router from Netgear to TalkTalk because of an intermittent signal, no problem with my desktop ethernet or laptop wireless or tablet but I keep loosing connection with my WII internet connection for Netflix.
View 10 Replies
View Related
Jun 4, 2012
I have a Cisco WRVS4400N on the latest firmware and I have just had my Virgin internet connection upgraded to the 100Mb. Once i thought it was upgraded i checked with a broadband speed test and it came back as 15Mb download and 5Mb upload. Before i rang Virgin i thought i'd check with a direct connection from my pc straight to the modem. Ran the speed test and it came back as 100Mb download and 5Mb upload. I thought the best thing to do is restore my settings back to factory and its still the same.
View 7 Replies
View Related
Mar 9, 2013
My internet connection speed, measured by speedtest.net with PC connected directly to cable modem, is ping=33ms, dn=48Mbps and up=7.6Mbps. (These values changes slightly with each test, sometimes being a bit higher and sometimes a bit slower, but usually being in the neighborhood of the 50Mbps promised by my ISP.) When this same test is run with the PC connected directly to a port on my RV180 (firmware version 1.0.1.9) the measured speed is ping=35ms, dn=30.66Mbps and up=7.45Mbps. Given that the RV180 is supposed to provide very fast WAN to LAN throughput (Small Net Builder's test result is 798Mbps dn and 811 up, measured with the same firmware version), why is my unit seemingly decreasing the internet connection (WAN) speed coming out of my cable modem? What, if anything, can I do to increase my WAN to LAN throughput?
View 1 Replies
View Related
Oct 18, 2011
For eight months we have not had any problems with our new WRVS4400N (V2.0.2.1) connected to a Verizon/Westell 6500 to provide DSL internet for our network with DHCP on our server... No changes have been made to the router or modem since initial setup; but, then it started -- Our internet connection would drop intermittently. Sometimes every 5 or 10 minutes - sometimes every hour. Verizon has tested the lines which came up ok, then they sent a tech who changed the wire pair coming into the building for the DSL line and retested the lines which again came up ok, then they provided us with a new modem (now a Verizon/Westell 7500). After all that, the DSL still connects then disconnects intermittently. I am now wondering if the issue lies with the WRVS4400N.
View 2 Replies
View Related
Sep 26, 2011
It is set to dummy mode so it should just pass through to the WRTG54S router which handles the DHCP.2) I have 6 computers sucking the internet off of the router. One is wireless.3) I have been set up for about 6 months this way. 4) I use to drop the DSL connection about twice a day. I would unplug the WRTG54S and plug it back in and everything would reset and work. Then, recently it has gone to about 15 times a dayThen, we have to make a major electrical change in the building, which required us to go to generator power only for 5 days. For 5 days, we never dropped the DSL connection a single time. Power was restored. Generator sent back home. Problem is back. Dropping DSL connection again.5) Hooked up APC battery backup power smoothing device to 3 cpus, WRTG54S, and DSL modem.
View 5 Replies
View Related
Dec 21, 2012
I am now using my dell optiplex 755, with windows xp sp3. The first set up was with wireless ,which works fine, but now I am trying to use the ethernet to netgear switch, to comcast modem, from dell desktop, I get error that says,TCP/IP is not enabled for thisconnection.Can not proceed. I have also tried to repair local connection with the Icon at the bottom, it has error that says ,local area connection.This connection has limited or no connectivity.do I need a new IP address for the this connection? I have tried to run ethernet from modem to computer ( to by pass the switch
View 5 Replies
View Related
Nov 17, 2012
My ISP tested my connection and told me my signal is very weak. I can no longer play games online because I lag tremendously. I can't steam videos while someone else is using the internet either. Also I can't access it on wireless devices unless I am in view of the router. I'm not sure what caused my connection to suck butI have the essential plan from cox.com. When I test my connection on speedtest.com I average 75ms/ping, 3.25mbps/dwnld spd, and
View 2 Replies
View Related
May 9, 2012
I have a 2nd pc that i want to add to my basic home network. I have installed a fresh copy of Windows 7 Ultimate 64bit yet still have issues connecting to my router. There is basic activity but nothing on the internet I have tried to use command line netsh to force DHCP on it says it is but I am getting a subnet mask of 255.255.0.0 when everything else is 255.255.255.0 not sure if this matters as there are only 4 devices on the network.
View 2 Replies
View Related
Oct 17, 2011
I have two wifi routers which I have connected together with an ethernet cable to extend coverage across my house. The ethernet cable is connected to a LAN port on the first router and the internet port of the second router. This works fine and creates a second network that I can connect to the net on. The problem iseemingly randomly, about every 15 minutes, the second router will lose internet connection. My laptops and phone still stay connected to it, but windows lists it as having no internet connection. If I then wait a couple of minutes and reconnect, internet will be working again.
View 4 Replies
View Related
Jun 8, 2011
I have a big 2 floor house .I would like to use 3G connection using USB type of modems,like vodaphone or MTS. which router to be used so that I can get good connectivity on both floors. NOTE- I do not want to use cabled internet coonections.
View 2 Replies
View Related
Sep 17, 2012
My problem is I can not connect to any ftp server or any database server using my home internet connection. But i can connect to the same servers using my work internet or even using my 3G mobile connection.I tried to contact with my service providers with no luck.I am using a Zyxel wireless router. Is there any settings in my router which stops me to connect those servers.
View 4 Replies
View Related
Jun 21, 2011
I have two routers one is a o2 router which is for the internet (broadband) the other is an old bt home hub which i have connected to the printer via usb. In order to print a document at the moment i have to disconnect my laptop from the broadband router and connect it to the printer router.Is there any way that i can connect to the two router s at the same time so that i while printing i can still keep my internet connection.
View 1 Replies
View Related
Feb 10, 2013
Belkin N300 - bought two weeks ago and have had very slow internet connection since.
View 1 Replies
View Related
May 31, 2013
I have a belkin N750 DB router. I recently upgraded by internet service from 15Mbp to 30Mbp. If I connect my computer directly to the cable modem, I get 30Mbp throughput. However, if I connect the modem to the router my speed drops to 15Mbp. How do I get the router to support 30Mbp?
View 2 Replies
View Related
Jan 16, 2013
F9K1103 v1 (01C) keeps loosing internet connection, the router is wired to a time warner modem and wireless is not enabled.
View 2 Replies
View Related
Feb 13, 2013
Having an issue with my Belkin N600 router - when initially installed it was working fine but in the past week it has gtten slower - if I connect directly to my DSL modem my speed is 1.5 MBS when I use the router connection my speed drops to .1 MBS - tried resetting to factory defaults & that did not work also tried resetting my modem *& router still having the same issue.
View 9 Replies
View Related
Oct 26, 2011
I am doing a comparative between cisco and sonicwall routers. Which router would better fit me? i need it to support at least a 20MB internet connection in a datacenter and has to have a firewall included. I was thinking about a router 1941. What do you think ?
View 1 Replies
View Related
Jun 27, 2012
We have an RV016 (hardware version 2, firmware version 3.0.2.01) behind a cable modem. Attached to this RV016 is a switch to which our other devices are connected. Among those is another switch, a wireless access point and our VOIP phone system.
The issue with this setup seems to be as follows:
The Mac machines at our office seem to be unable to get internet access reliably. What we have observed is that a connection to the wireless access point is made. Google will load fine, then when performing a search it comes back with either a dns lookup error or just says that the site can't be found. Sometimes sites will load just fine, sometimes they don't. Our Windows or Ubuntu machines in our office hardly ever have that issue, but they do on occasion. Essentially internet is usable on Windows and Ubuntu, but not on a newer Mac. Mainly three Macs are affected that run a newer OS. Two other Macs (older OS) seem to be fine. My coworkers (who have that issue at work) report that at home they do not.
The DNS servers on the router were set to our ISPs addresses. I have since changed them to opendns servers. The issue persists.
When connecting a MacBook directly to the cable modem, everything works fine. Since we are using NAT, I do need to use the router. There are devices attached to it that these users need to be able to get to.
View 10 Replies
View Related
Apr 26, 2011
Is it possible to setup a router to router connection over the internet with fixed IP Addresses with two WAG320N?
View 3 Replies
View Related
