Cisco Routers :: RV180 Decreases Internet Connection Speed?

Mar 9, 2013

My internet connection speed, measured by speedtest.net with PC connected directly to cable modem, is ping=33ms, dn=48Mbps and up=7.6Mbps. (These values changes slightly with each test, sometimes being a bit higher and sometimes a bit slower, but usually being in the neighborhood of the 50Mbps promised by my ISP.)  When this same test is run with the PC connected directly to a port on my RV180 (firmware version 1.0.1.9) the measured speed is ping=35ms, dn=30.66Mbps and up=7.45Mbps. Given that the RV180 is supposed to provide very fast WAN to LAN throughput (Small Net Builder's test result is 798Mbps dn and 811 up, measured with the same firmware version), why is my unit seemingly decreasing the internet connection (WAN) speed coming out of my cable modem?  What, if anything, can I do to increase my WAN to LAN throughput?

ADVERTISEMENT

Cisco Routers :: Linksys SRW2008P Decreases Network Speed

Jun 3, 2013

I try to connect Siemens SIP IP phone to switch LinksysSRW2008P with PoE for scheme:
main switch <-------> linksys <-------> phone

I can't have access to Linksys by local network or web interface, so I connect through COM port and reboot the device and restore all settings to defaults. There was another linksys switch with the same default IP in my network, so I've tried to change ip address for my Linksys device. After that I can ping switch IP without lost packages successfully and partly access to login page by web, but including Linksys to the local network causes decreasing all network working speed, so the web administrative form can not be loading at all.    In both cases (default ip or another one) the set isn't working, so I can't have access to the phone by ping or web interface. The cable to main switch inserts to port 1 and green rectangle indicator is flashing rapidly. The cable to the phone inserts to port 2 and orange indicator is lighting, green indicator is flashing slowly.   Interestingly, only one port has status UP (port 1), all another port has status DOWN. If I replace cables ports with each other, only the port where cable to main switch is inserted, will have status UP. The phone station is getting power from switch in both cases.  I've tried to change Spd/Dpx ports' parameters, used DHCP for getting IP, but I've gotten no result.  How can I solve the problem? Is Linksys switch worked or defective?

View 2 Replies View Related

Internet Speed Decreases Due To The Use Of Torrent Downloads?

Aug 17, 2011

We are using WI-FI with more than 20 clients at a time.Now the speed seems to very decreased,because most of them using torrents for downloading.Is this the correct reason for low speed?How can I detect who or howmany people using torrent?And is there any need to block torrents?

View 3 Replies View Related

Cisco Routers :: Very Slow WAN Speed (RV180)?

Jan 30, 2013

My brand new RV180 seems not to be able to exceed 1.1 MB/s WAN download speed. Using a simple Linksys WRT-320N I used to have 5-6 times this speed. Value is with default settings, various sources (HTTP/NEWS downloads). Trying to improve this wit QoS-settings dows not improve this in any way.

View 2 Replies View Related

Download Speed Decreases From 2mb To 50Kb

Sep 25, 2011

My download speed has decreased to about 1/40th of its previous speed, while my upload speed remains the same. Speedtest shows that my connection is equally strong as it was prior to the slowdown, even though I can't even get anything close to my original speed.Fully detailed version: About a week ago, my download speed decreased from 2 megabytes/s to about 50 kb/s. Prior to the speed decrease, I did not install or update any programs, so it's probably not an interference from some wayward program.

View 12 Replies View Related

Cisco Routers :: RV180 Download Speed Drops To Half Of Capacity

Jan 24, 2013

When enabling the WAN Traffic Meter on my RV180 with firmware 1.0.1.9, my download speed drops to half of my capacity.WAN Traffic Meter disabled: download around 13 MB/sec, WAN Traffic Meter enabled: max 6 MB/sec.WAN QoS is disabled!

View 1 Replies View Related

TP-Link 150Mbps Wireless :: TL-WR740N Router - After Forwarding Port Speed Rapidly Decreases

Dec 3, 2012

I have TL-WR740N router. ISP should provide me up to 100Mb/s internet speed. Actual measurements shows me about 80 Mb/s. The problem is when I enable 3389 port in Port Triggering my internet speed drops to 2,5 Mb/s. When I disable port triggering, speed become normal again.

View 3 Replies View Related

Belkin Routers :: N750 DB - Internet Connection Speed?

May 31, 2013

I have a belkin N750 DB router. I recently upgraded by internet service from 15Mbp to 30Mbp. If I connect my computer directly to the cable modem, I get 30Mbp throughput. However, if I connect the modem to the router my speed drops to 15Mbp. How do I get the router to support 30Mbp?

View 2 Replies View Related

Cisco Routers :: RV180 IPSec Connection Dropped?

Mar 14, 2013

I'm using two RV180 for a site to site ipsec vpn. The IPSEC VPN connection is working only if I try a manual connect. After some time connection is droped and no auto reconect for it.

View 6 Replies View Related

Cisco Routers :: Rv180 IPsec Connection To Netgear Prosafe 336g

May 16, 2012

I used to have a Netgear Prosafe 318 conncted to a Netgear Prosafe 336G in a small office environment across the WAN between two offices, IPsec preshared key.  The 318 took a dive so I decided to upgrade to a new Cisco RV180 VPN router.  I set up the VPN access rules exactly the same and forklift upgraded the Prosafe 318 (same IP, same rules, same pre-shared key, IKE setup etc) and the VPN tunnel comes up fine. However, even though the VPN tunnel says connected and I have no problems pinging anything across IPsec between subnets I cannot seem to connect to anything from the cisco side.

From the Netgear side I can connect to anything on the cisco subnet (192.168.0.1 / 255.255.255.0) but from the cisco side anything I try and connect to on the netgear side (172.16.0.1 / 255.255.255.128) times out.Encryption AES-128 (although also tried 3des), Sha-1   SA-lifetime is 3600 seconds, PFS key group enabled DH-group2 (although also tried group1)IKE policy direction Both, identifier FQDN (both sides), Preshared key SA-lifetime 28800 seconds. Firmware is updated on both the netgear and the RV180 to latest version (1.0.0.30 on RV180).Like I said from Netgear to Cisco through VPN tunnel everything works fine from Cisco to Netgear everything times out.

View 1 Replies View Related

Cisco Routers :: RV180 And Internet Explorer 10 Not Compatible

Feb 27, 2013

I am running firmware 1.0.1.9 on an RV180.  After recently upgrading to Microsoft Internet Explorer 10, I notice the RV180 administration screens do not display properly.  Specifically, the horizontal window pane is set so high (not adjustable) all the information is not fully displayed.  If I use a previous version of Internet Explorer I don't have a problem or if I use another browser like Google Chrome I don't have a problem.  So it appears the RV180 and Internet Explorer 10 are not fully compatible.
 
Below is a screenshot using Internet Explorer 10 showing the Status page.  You can see the horizontal window cuts off most of the information and there does not seem to be a way to "pull" it down to display more information.
      
Here is the same Status Dashboard selection via Google Chrome.  Unfortunatly I don't have Internet Explorer 9 still installed, but it worked fine.

View 5 Replies View Related

Cisco Routers :: RV042 - Internet Speed

Feb 23, 2012

I have 02 router Linksys Rv042 ( 01 old and 01 new ). I'm config router Rv042 new and router connect Internet. But router connect internet very slow. When i using Vigor 2910 connect internet very Fast or using router Rv042 Old connect internet very fast. Two Rv042 the Same. I don't using firewall.

View 4 Replies View Related

Using 2 Routers Slows Internet Speed?

Feb 22, 2011

I have FiOS and their supplied wireless router Actiontec #: MI424WR. I have equipment that uses the newer N signal so I purchased a Linksys E3000 Wireless-N Router. This is working great for my wireless home theater equipment but I am having problems with my wired speed. It has gone from 20 to 30 mbps to around 10 mbps. I have one of the LAN outputs on the Actiontec feeding the Linksys input, I have my computers plugged directly into the Linksys verses the Actiontec. This makes it easier to program the Linksys router. Since I am no longer using the wireless part of the Actiontec there really is no need to be plugged into it. Is there anything I can do get my speed back or will I have to plug the computer back into the Actiontec and move it every time I may need to make a change to the Linksys

View 3 Replies View Related

Speed Up Internet Connection Through Registry?

Jun 12, 2011

how to speed up my internet connection through registry or any other easy way to increase speed?

View 1 Replies View Related

How To Optimize Internet Speed Connection

Jun 15, 2011

How can I optimize my computer's connection speed? I'm using a Dell Vostro 1500 laptop, and I used to have Vista installed on it. When I used that, my connection(via speedtest.net) was around 25mbps. I reformatted it last Summer and installed Windows XP Service Pack 3 onto it. A few months ago, I used speedtest.net and my speed test was around 16mbps. Now, my speed test is 8mbps. How can I optimize my internet connection speed? My internet service provider is Comcast.

View 3 Replies View Related

Cisco Routers :: RV180 Ssh And Https From WAN?

Dec 23, 2012

Is there any way to manage the RV180 from the WAN side via https and/or ssh?Also, is ssh from LAN even available?

View 3 Replies View Related

Cisco Routers :: RV180 VPN Does Not Work

Oct 18, 2012

I have an RV180 VPN router.I try to enable the VPN users with PPTP or QuickVPN but is not working.For PPTP sometimes my windows 7 connects to the router, sometimes doesn't connect with a random error message.When it connects, the windows 7 from outside the lan can see the computers from inside the lan but the computers from inside the lan cannot see the windows7 one. This is random also. When i succed to connect, from that computer, the internet is not working anymore.I tried to set the VPN in the same subnet as lan, i tried with different subnet. Is not working.I updated the last firmware. The same.Restore factory settings couple of times, the same.

View 6 Replies View Related

Cisco Routers :: Bug In RV180 Firmware V1.0

Jun 17, 2012

I noticed if you add more than 10 access rules to the Access Rule table, you are unable to reorder past the first 10.Steps to reproduce:Create 11 rules of the same stream direction, outbound or inbound (...I found the bug with outbound, did not test inbound).try to reorder one of the first 10 rules to the end of the list, either by entering "11" manually, or by pressing the down arrow.System responds that "11" is an invalid number, or that the rule cannot be moved.This issue is not reported in the "Known Issues" section of the release notes for 1.0.1.9.

View 2 Replies View Related

Cisco Routers :: How To Connect OS X 10.7+ To RV180 VPN

Mar 2, 2013

Which vpn client to use on os x ? (the one included in os x or another?) Which VPN configuration to use on RV180 ? and Which ports to open on RV180 Firewall ? (or any other parameters)

View 1 Replies View Related

Cisco Routers :: RV180 - Log Warnings With QOS IP Or MAC

May 20, 2013

I had set up QOS for an IP Range and noticed the logs filling up with Warnings - hundreds within less than an hour.
 
I finally reset the router to factory and then step by step re-built my configuration - it was the QOS that started generating these warnings like:
 
Tue May 21 13:18:39 2013(GMT-0500) [rv180][Kernel][KERNEL] [87073.550000] IN=bdg1 OUT= DST MAC=d8:67:d9:c3:a0:2e SRC MAC=00:0e:58:58:57:7a PAYLOAD TYPE=08:00 SRC=192.168.1.193 DST=208.85.44.22 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=19313 DF PROTO=TCP SPT=1768 DPT=80 WINDOW=2534 RES=0x00 ACK URGP=0 MAR

[Code].....

In both cases above, after I started to suspect QOS, I entered a narrow IP range to test and then a MAC to test.  Using a VLAN seems to work fine and generate no errors - even a VLAN for the same associated host(s).
 
I have a support case open about this - didn't get too far yet, but now with a better repro, maybe they will.

View 1 Replies View Related

Cisco Routers :: Linksys WRVS4400N V1.1.13 Slows Down Internet Speed By 50%?

Dec 10, 2012

Recently I upgraded my Internet speed at the ISP from 10Mbps to 25Mbps and the problem is that I am measuring only 15Mbps using [URL]On the day when the tech came out to install the new DSL modem, he noticed the difference and as part of troubleshooting, he bypassed the Linksys router and voila the net speed measured 25Mbps using speedtest.net.So, why my Linksys WRVS4400N V1.1.13 acts like a bottleneck in this case? I didn't have this problem at the speed of 10Mbps. The upload speed is OK, it is 5Mbs with or without the DSL modem.

View 2 Replies View Related

Increase Internet Speed Connection To 100mbps?

Aug 9, 2011

how to my increase Internet speed connection 100mbps

View 1 Replies View Related

Belkin Routers :: N150 / F6D4230-4 V1 - Low Internet Speed

Nov 3, 2012

I recently got a Belkin N150 Enhanced Router Model F6D4230-4 V1. I upgraded it to the recent firmware.

I use it NOT to access internet, but only to hook up my desktop computer with my laptop and my tablet PC. I use Win7 Ultimate on both computers. I configured a Win7 home network and I managed to access shared files between the 3 devices.

However, the speed is very very low, not going over 1.5 MB per second , sometimes even less, although the signal strength is the maximum (54).

The distance between the laptop and the desktop is only 4-5 meters, in the same room. My laptop is HP Compaq 6710b which has what seems to be a "Intel(R) PRO/Wireless 3945ABG Network Connection" .

Transfer speed is the same whether transferring from or to the laptop. I configured the laptop according to the instructions in the manual.

View 8 Replies View Related

Cisco WAN :: Add T1 To MLPPP Decreases Bandwidth?

Feb 27, 2013

I have 4 T1s going to a site, 2 of which are new (all 4 are with the same provider).I initially noticed that throughput of the 4xT1 bundle seemed a bit off, so I did additional testing.I found that whenever I have a certain T1 in the bundle (whether its 2xT1, 3xT1 or 4xT1), throughput is drastically decreased.There are no errors on the circuit, so my provider is being difficult about "repairing" it since they also see no errors.

View 1 Replies View Related

Cisco Routers :: RV180 What Are The Alternatives For Android ICS

Oct 30, 2012

I  currently have an RV180 in a small business set-up and curently being  accessed remotely by laptops (Quick VPN) and Ipads/Android ICS tablets  (PPTP).  All is working well but I've become concerned about the  security risks of PPTP and would like to shift the tablets to IPSec. 

1) For a  small business are the PPTP risks real?

2) What are the alternatives for Android ICS?  I can't find a Quick VPN client for Android.

3) I can't get the core IPSec VPN in Android to connect to the RV180?  Is this possible? 

View 1 Replies View Related

Cisco Routers :: NATed Did Not Add VLAN On RV180

May 7, 2013

I have RV180 configured with two VLANs. First VLAN is untagged and second VLAN is tagged. The purpose is two have two subnets, with the second subnet used for guest access. Both VLANs have DHCP server enabled. First VLAN is 192.168.1.0/24 and the second VLAN is 192.168.2.0/24, When I connect a computer with untagged Ethernet interface, it gets an IP address from DHCP server on the first subnet i.e. 192.168.1.100 and it can successfully access Internet. When I connect a computer with tagged Ethernet interface (I am using VLAN ID 10), it gets an IP address from DHCP server on the second VLAN i.e. 192.168.2.100. So far so good. I can successfully ping hosts on the Internet i.e. ping www.google.com. But I cannot access Internet from the web browser. I captured Wireshark trace and here is what I see...

1. TCP SYN. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
2. TCP SYN ACK. Source IP A.B.C.D, destination IP 192.168.2.100. Ethernet frame has VLAN tag (VLAN ID 10)
3. TCP ACK. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
4. TCP Data. Source IP 192.168.2.100, destination IP A.B.C.D. Ethernet frame has VLAN tag (VLAN ID 10)
5. TCP Data. Source IP A.B.C.D, destination IP 192.168.2.100. Frame is untagged
 
The problem is at #5. Packet came back from the Web Server. RV180 properly NATed it to the local IP address. But it did not add VLAN tag.

View 8 Replies View Related

Cisco Routers :: Rv180 Dropping LAN Connections?

Mar 13, 2013

I just recieved a new RV180 yesterday and it will not connect to my switch. Router was updated to the newest firmware, reset to factory settings. I did change the ip and ip range. Router works fine with one computer attached direct. As soon as I connect my sf300-24P to it, the WAN and LAN lights all light up and then go out. Only the WAN will light back up. I have no connectivity to the router. I plug the laptop to the router directly and no LAN lights come on and can not see the router with arp -a.

View 6 Replies View Related

Cisco Routers :: How To Enable Telnet On RV180

Mar 9, 2013

I'm trying to telnet into the my RV180 router. How do I go about it.
 
I created 3 VLANS

1  at 192.168.1.1
20 at 192.168.20.1
30 at 192.168.30.1
 
Here is the Multiple VLAN Subnet Table:

1     192.168.1.1    255.255.255.0DHCP ServerEnabled 10192.168.10.1255.255.255.0DHCP Server  Enabled 20  192.168.20.1 255.255.255.0    DHCP ServerEnabled 

I can ping the router at all 3 IP addresses.How do I enable the telnet service on the router?

View 1 Replies View Related

Cisco Routers :: RV180 And IPSec VPN Client

May 22, 2012

Does RV180 router support client VPN connections using regular Cisco VPN client? Datasheet says it works with Quick VPN client.

If regular non-Quick client is not supported, can both clients coexist (= be installed simultaneously) on the same PC?

Does Quick VPN client support split tunneling?

View 2 Replies View Related

Cisco Routers :: Does The RV180 Series Support 6rd

May 10, 2012

I'm considering upgrading a small business to the newly released RV180 or RV180W.Does the RV180 series support 6rd (IPv6 rapid deployment?).I see 6rd documented in the other small business routers (e.g. RV110), but I can't find it in the RV180 documentation.

View 1 Replies View Related

Cisco Routers :: RV180 Quick VPN To Connect

Aug 6, 2012

I'm having issues getting QuickVPN to connect. I think it's an issue pinging the gateway but I'm not 100% sure. We are using Comcast Business, I have placed the RV180 in the DMZ. The setup looks like this: Internet -> Comcast router -> RV180 (DHCP) -> rest of network.

View 5 Replies View Related

Cisco Routers :: RV180 VPN Guide Required

Apr 3, 2013

Is there a guide to setup a VPN connection using this router? I've follow the setup guide provided by cisco but I'm having issues.  When attempting to connect using the quick vpn client, I get error messages.

View 1 Replies View Related

Cisco Routers :: RV180 IPSec Needs Polishing

Apr 26, 2013

Any news on a new firmware for the RV180? I have the most recent version but it still has lots of bugs. IPSec needs polishing. In addition the Logging functions don't work well. I can't send to a syslog and when I try to email the logs I get a email saying there is no data even though several pages of enteries are visible in the web GUI. I've checked the profiles and they are correct. I even tried using just the 'default' profile but no luck.

View 2 Replies View Related

Cisco Routers :: SB RV180 VPN Users Not Showing Up?

May 15, 2013

I have a Cisco Small Business RV180 and I have several VPN users configured.  IPsec between my home router (also an RV180) and work router (router in question) is working fine, several PPTP users working fine and 1 QVPN user that works as well.  I set up another qvpn user and it didn't work.  I went back into the router to check and make sure I hadn't goofed something up and saw that I had 8 lines, 1 and 2 were the QVPN users and 6 other PPTP users, however, the "pages" footer (for lack of a better word) only displays 1 -5 of 5 instead of the 1-8 of 8 I would expect it to show.I dumped the cfg file and opened it up, all 8 user configurations show up.  One was my user account which showed negative numbers for the logon time, something like -1day -hours -minutes -sec, so I thought that that might be locking up the router or something so I deleted my PPTP account but it didn't allow the new user access.  I deleted all PPTP accounts and no luck there either.I'm running firmware 1.0.2.6.

View 4 Replies View Related

Cisco Routers :: RV180 Router Will Not Connect To ISP

May 16, 2012

I am contemplating replacing my Juniper Netscreen 5GT with this new RV180.
 
serial number 161303LB 
RVC180 V01
 
However, it will not connect to my ISP (DSLExtreme) using the same settings I have been using for multiple years. DSLExtreme is using AT&T DSLAMS, as you likely know, and I am unaware of anything unique about how they serve DHCP?
 
The Cisco wizard sits on the WAN configuration check forever, and never connects. I have rebooted it and allowed it to sit for fifteen minutes trying. I think that is enough.
 
The 5GT WAN interface is configured for "DCHP Client" and that is how the RV180 is configured.
 
It is a standard 6MB DSL line, I have tried both the existing cable, as well as the provided one to connect to the D-Link 2320B modem/bridge, which, as I indicated, syncs almost instantly with the Netscreen. No difference when the cables are swapped.

View 3 Replies View Related

Cisco Routers :: RV180 Will Not Connect To ISP Using PPPoE

Mar 17, 2013

The RV180W would not connect to an AT&T DSL connection using PPPoE (modem in bridge mode), or behind the DSL Modem/router with the DSL modem/router providing a dynamic IP to the RV180W or a cable modem (TimeWarner Roadrunner dynamic IP).  I upgraded the firmware yesterday and now the RV180W will connect to a dynamic WAN IP, but it still will not connect using PPPoE.
 
I have also noticed the admin interface is only accessible about 75% of the time.  When going to 192.168.1.1 the login prompts either don't come up or if they do, after logging in, the screen never fully loads after that.  I have to reboot the router to get it to work.
 
Also, the router has not yet pulled DNS from either the DSL or the cable modem.  I had to manually enter those addresses.

View 1 Replies View Related

Cisco Routers :: Connect L2L Between RV180 And ASA5505?

Feb 27, 2013

I've been trying to connect L2L between RV180 and ASA5505 but no succeed.I can do RV180 to RV180 l2l with one of it on Aggresive mode. working configuration sample of RV180 L2L ASA5505?

View 1 Replies View Related

Cisco Routers :: RV180 PPPoE Not Working

Oct 15, 2012

My RV180 does not route properly between LAN and WAN through my PPPoE account. I am able to ping public IPs directly from the RV180 (through the diagnose section) but can not do it from any PC on LAN. The exact same configuration works perfectly well with a Linksys WTR610N. I upgraded formware from 1.0.0.30 to 1.0.1.9 but that did not make any difference.
 
The only time the RV180 will route is right after I reset to factory defaults and re-enter PPPoE account name and password. If I then reset my modem or the RV180, the RV180 does not route anymore between WAN and LAN even after several minutes and even though I can ping public IPs from the RV180.

View 18 Replies View Related

Cisco Routers :: RV180 Access Rules And One-to-One NAT

Nov 15, 2012

I have 2 static IP addresses that I'd like to point to 2 corresponding servers in my LAN.  I've followed the Access Rule and One-to-One NAT instructions as best I can (screenshots of each for one of the static IP scenarios attached), but no luck.  The static IPs bring the outside/WAN user to the RV180's admin login screen.

View 2 Replies View Related

Cisco Routers :: RV180 - Configuration Possibilities

Jun 17, 2012

I just set up a new RV180 router in a SOHO environment. A couple questions regarding the configuration possibilities:
 
1) Is there any way to deny static IP LAN traffic and force all clients to DHCP? It seems the RV180 is very "IP range" based, so I'm dividing user privileges based on IP grouping. It would be simple for a user to circumvent this by simply assigning a static IP address in a range that has higher access.
 
2) Is the Access Rules table a "first match" or "last action" type of table? Meaning... "first match": the first rule that matches all conditions is hit and the rest of the table is ignored. "last action": the last rule that matches all conditions to modify the traffic is what is used.
 
The reason I ask this is I want to ban all outbound traffic from a range of IP except a handful of services, and there are multiple layers of internal IP ranges that will be allowed different levels of outbound access.

View 1 Replies View Related

ADVERTISEMENT