recently got a RV220W and liking all the configuration options.
Although I cannot find where to change the listening port for management? I want it to listen on port 81 instead of 80.
I just purchased 5 RV220W to act as internet/wireless router at a remote site. There is no VPN, just LAN and Wireless routing to the internet.I have setup remote management and it works fine when I am directly connected to the internet. However, everytime I try to connect through our HTTP/HTTPs proxy farm, it usually fails. Specificially, I get the log-in page and can log in. It starts to render the landing page but redirects to a page stating "Your session has been terminated." On rare instances the first page will appear, however within a few clicks I end up with the same terminated page.
As a test, I bypassed the farm and forced my browser to use one proxy exclusively. At that point I could access the HTTPS interface with no issue. I have not had any issues with other SSL sites with the proxy configuration in use.Is there some sort of MITM prevention I could be running into? If so, can it be turned off.I am new to the RV-series of routers. Is there any logging I could turn on that would provide insight on why the session may be getting terminated?
How to set the default outbound policy as block in access rules of rv220w? I configure my company router RV220W to block all outbound service traffic, just allow outbound service as : http, https, smtp, dns_tcp / udp. it works fine for some hours, the next day, the rules like expired, the https / smtp / DNS service fail to outgoing, only the http is still ok? What happen? Now I just set the default outbound policy as allow, all traffic can go out, but that is meaningless for a firewall device.
View 1 Replies View RelatedI recently had a security scan done on a DIR 655 and the report came back saying PORT 111 (Unix RPC Service) should not be listening for external connections. I've looked through every setting but can't find where this service is enabled (or can be altered) -- aany guidance on this port/service?
View 14 Replies View RelatedI am just setting up a LAN using DIR-655 and I noticed this line in the logs: notice Aug 4 03:25:55 HTTP listening on port 65535
Is the router listening to that port?
Ages ago I was shadowing someone making a change on the network. I cannot remember which spanning tree version was running and cannot remember the config of any port either. What I do remember is that every switch port on the 2960 switch went orange and an outage occured, where the ports went into listening / learning mode. I assume that the STP was just the default ieee 802.1D.
View 3 Replies View RelatedI'm having yet another issue with my RV220w. I thought this would be a wise buy, but I keep finding reasons to hate myself for buying this router.Anyway, I need to forward port 3389, Windows Remote Desktop Protocol to one of my internal servers. I have defualt NAT, defualt firewall, etc. etc. I have seen documentation that says that Firewall -> Port Forwarding is non-functional, so I attempt to set up port forwarding via Firewall -> Access Rules. I did not see "RDP" or any other obvious acronym for Remote Desktop Protocol in the services list. So, I made a custom service, called RemoteDP, TCP protocol, port 3389 to 3389.No, I cannot RDP to my server from WAN. This was easily achieved with a cheap NETGEAR router from 2005.
View 2 Replies View RelatedHow can one forward a range of ports?
Suppose I have defined the following service:
Service: TEST
Port type: UDP
Starting port: 5060
Ending port: 5070
and I want to forward it to a specific IP. Then, if I create a new port forwarding rule for this service it asks me to specify a single port number to be used internally as:
Action: Always Allow
Service: TEST
Source IP: Any
Destination IP: 10.0.0.100
Internal Port: ?
I want to forward all ports from 5060 to 5070 to the internal range 5060 to 5070.
I made a custom port forward using tcp ports 2121-2130 to a private IP address on my network (192.168.1.8). Whenever I do this, RV220W CPU usage spikes to 98-99% and my Internet connection starts lagging a lot. Just disabling the port forward from the administation console fixes this. I'm running the latest firmware.
View 1 Replies View Relatedi have a Problem with my Cisco RV220W with the Firmware 1.0.3.5.I have in my LAN a Dreambox with the IP Adress 192.168.1.230, he listen to the Port 8880.How can I set up a port forwarding from the WAN to the Dreambox ?
View 2 Replies View RelatedI have a RV220W with 1.0.3.5 Firmware installed.
I also have a few servers with services I need to expose to outside the network (RDP and some websites) where the external port is not the same as the LAN port. I could accomplish this with my previous router using port forwarding and it looks like I can do the same here on the RV220W but I can't quite get it to work successfully.
I've several production Catalyst switches that are listening on the same IPv4 and IPv6 ports. The problem is I don't want the switches listening on the IPv6 ports.[code] How to shut down these listening ports?I also have a few production switches listening on UDP/10000 and I cannot determine why this port is listening. [code] I've seen where UDP/10000 is Network Data Management Protocol and is related to Storage networks ###, but I've also seen where UDP/10000 is the default port for IPSEC data.I don't believe UDP/10000 is related to either NDMP or IPSEC data, though I could be very wrong.
View 4 Replies View RelatedI have read every post here about port forwarding on the RV220W and none are clear. Here is my scenario.
I have 5 static IP Addresses. I want to use one of the IP addresses to setup remote access using Remote Desktop Connection from outside the office using port address translation. for example i would like to use RDC and a specific port such as 7000 and connect to an internal PC on port 3389. sounds simple. i do this all the time on Cisco ASA's, Netgear, D-link, etc. but for the life of me cannot do it on this cisco firewall. so the port address should look like 25.25.25.25:7000 and connect to 192.168.1.25:3389. i have tried everything based on the posts without luck.
I have a setup with 2 RV220W at 2 locations.Both with the latest Firmware (1.0.3.5). I configured portforwarding for RDP at one site. Works perfekt. I also configured an IPSec VPN between the 2 sites. Works too.
Configuration overview:
Site_1:
- IPSec VPN to site_2
Site_2:
- IPSec VPN to site_1
- Port forwarding for RDP to a local server (server_2)
My first problem is that i can ping server_2 through the VPN from a pc within site_1 but i can not access this server via RDP. As soon as i disable the Portforwarding for RDP at site_2, RDP via VPN works! I assume, that the RV220W mixes up portforwarding and VPN.I tried to set up an additional firewall rule at site_2 allowing the traffic between the local networks of both sites without restrictions and place this rule at toe top. But here is my second problem: I can not add any destination network to the firewall settings (firewall-->access rules). I only allows me to define a host to redirect the traffic to.
I have recently separated a few sites that I operate, into multiple virtual machines, all with their own IP.Basically, site A is located on for instance www.siteA.com, Site B is located on blog.domain.com etc etc. So my question is, how do I (with the Cisco RV220W), forward port 80 based on host?[URL]
View 3 Replies View RelatedI have setup port forwarding on the RV220W, to allow outside connections on RDP. I have tested that LAN RDP works fine, but when I test using an outside address trying to connect to an inside windows PC with RDP nothing happens.
View 11 Replies View RelatedI have a brand new RV042 v3 that I just updated to the latest firmware (v4.2.1.02) and have stumbled across an anomaly... I can only access the router from the WAN port using port 80. I happen to have it set to port 8080, but that doesn't work; I have to use standard port 80.
I have two other RV042 units running older firmware and they work as expected and follow the port that is filled in. This one has me puzzled and wondering if this is a bug in the firmware.
I'm trying to find a router that can do port forwarding to other subnets. My current linksys has IP of 192.168.1.1, and only allows me to port forward to 192.168.1.x, but I need to forward to 2.x, 3.x, 4.x
I can see how to do this on the RV215W through the online emulator, but Cisco suggested I use the RV220W. Looking through the device emulator, I can't seem to figure out how I would set it up.
From an older manual it describes how to configure this. I installed the oldest firmware available for download and this feature is there. Was this just simply moved somewhere else in the newer firmware?
Configuring Port VLANs
You can associate VLANS on the Cisco RV220W to the LAN ports on the device.
By default, all 4 ports belong to VLAN1. You can edit these ports to associate them
[Code].....
In my LAN environment, I'm using two cisco SG300-10 switches. Both switches are connected by GE10 on both switches, where both ports are set to trunk.Now on all ports 1-9 on both switches, I'm having client computers attached. So I set ports 1-9 to "access" mode.All interfaces on any switch is left in default vlan.
Is it normal that I see all traffic from all connected devices on any port where I connect a listening device?What I'd like to achieve is, that only traffic that is meant for a specific workstation is actually forwarded to this workstation. By now it seems that I get all the traffic from everybody.
This is the RVS 4000
Firmware version 1.3.3.5
STAR 9202 Chipset
64 MB DRAM
8MB Flash
DOS, Block WAN Rq, Remote mgmt all OFF
IPSec Tunnel none used
[code].....
Every day or so the Router becomes unresponsive to the HTTP mgmt interface, as well as it no longer offers DHCP services.then this happens the only remedy is to power reboot.
Everything comes back online just fine, however, the LOGS are initilaized so no data to figure out what`s going on.My next step is to setuo a syslog server and have the logs copied out.( No, I have no Torrents running at all, but I do have several devices like AppleTV, PS3s etc that run streaming Video plus I have the SPA3102 )
I replace our aging rv082 routers with wireless rv220w routers. The gateway to gateway vpn works great, however I am no longer able to manage our print servers port 80 management page. I can ping any host with success, and I can manage hosts that have a port 10000 or 8000 web interface - but no port 80 ones... I had no issues when using the old rv082 routers...
View 0 Replies View RelatedI've got a 3750X, IOS 15.0 IP Base license, reset to factory defaults, and I want to use the FastEthernet0 out-of-band management port on the backside next to the console port. The idea is that this port should provide a management interface that does not participate in the routing table. Problem is, contrary to the documentation, that configuring an IP address on the interface does make it show up in 'show ip route'. So it's still part of the routing table. Also, I'm unable to find the commands to change this and set a default gateway for just the management interface. I'm pretty sure this has to be possible, I remember seeing something similar on an ASA once. The 3750 configuration guide on Cisco.com does not seem to mention it.I considered using VRF but it's an IP Base license, no VRF.
View 1 Replies View RelatedI got question about Cisco SF300-24P- is it possible to have management vlan in other vlan than in default vlan?I have default vlan 10 and voice vlan 20, I need to reach switch through voice vlan so I need to set up, interface vlan 20 with ip address. I ask these, because in gui, under Management Interface, IPv4 interface,under Management VLAN, I can only choose vlan 10, which is my default vlan, I dont have option to set ,up, in this case, vlan 20 as management vlan.
View 2 Replies View RelatedI have an all gigE 3560. I don't use the management FE0 port on the back. I was thinking to use that for a 100Mbps WAN connection.
Seems to work just fine when I plugged in an test. But I am not routing across that link yet as I still need to setup the far end.
Is there any reason this would not work? I would like to not burn a gig port if the max throughput of the circuit is 100Mbps.
I have got ASA 5520. How to use the management port as a normal port on ASA. What are the basic reqirements for that.
View 3 Replies View RelatedSo here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
Is it possible to configure the RV220W to forward ports without connecting to the SSL VPN?
View 9 Replies View RelatedI saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies View RelatedI have interfaces defined on the 5505:
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
[Code].....
I only need one interface to connect to a single host on the inside (VLAN1) and then connect E0 to a DSL.
Is it possible (are what are the commands required) to take one of the other interfaces and create a Management port on the local office LAN?
I just purchased 2 SF-300 48 port units for 2 customers. I want to be able to remotely manage them over the Internet with my browser. BUT, customer sites already use port 80 for web servers. So, how do I configure this switch to use some other port than 80?
I called support, and much to my surprise he said it cannot be changed. How bizarre that a device with many hundreds of configuration settings does not have one of the most basic settings...
At one customer site I can configure port forwarding and translation to get around this problem, but the other site's router does not offer port translation..
I'm having an issue with the 5508 management port .. I can't seem to ping it from the switch connected to it .. ( the Show cdp command shows that the two can see each other .. but no ping is possible ! [code]
View 4 Replies View Relatedi am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration
View 1 Replies View Related