D-Link DIR-655 :: Is PORT 111 Really Listening

Aug 16, 2011

I recently had a security scan done on a DIR 655 and the report came back saying PORT 111 (Unix RPC Service) should not be listening for external connections. I've looked through every setting but can't find where this service is enabled (or can be altered) -- aany guidance on this port/service?

View 14 Replies


ADVERTISEMENT

D-Link DIR-615 :: HTTP Listening On Port 65535

Aug 4, 2011

I am just setting up a LAN using DIR-655 and I noticed this line in the logs: notice   Aug 4 03:25:55   HTTP listening on port 65535

Is the router listening to that port?

View 1 Replies View Related

Cisco :: Spanning-tree Every Port Go Into Listening / Learning State

Apr 4, 2012

Ages ago I was shadowing someone making a change on the network. I cannot remember which spanning tree version was running and cannot remember the config of any port either. What I do remember is that every switch port on the 2960 switch went orange and an outage occured, where the ports went into listening / learning mode. I assume that the STP was just the default ieee 802.1D.

View 3 Replies View Related

Cisco Routers :: RV220W Default Listening Port For Management

Aug 13, 2011

recently got a RV220W and liking all the configuration options.
 
Although I cannot find where to change the listening port for management? I want it to listen on port 81 instead of 80.

View 5 Replies View Related

Cisco Switching/Routing :: UDP Port 10000 And IPv6 Ports Listening

Aug 30, 2012

I've several production Catalyst switches that are listening on the same IPv4 and IPv6 ports. The problem is I don't want the switches listening on the IPv6 ports.[code] How to shut down these listening ports?I also have a few production switches listening on UDP/10000 and I cannot determine why this port is listening. [code] I've seen where UDP/10000 is Network Data Management Protocol and is related to Storage networks ###, but I've also seen where UDP/10000 is the default port for IPSEC data.I don't believe UDP/10000 is related to either NDMP or IPSEC data, though I could be very wrong.

View 4 Replies View Related

Cisco Switching/Routing :: SG300-10 See All Traffic From All Connected Devices On Any Port / Where To Connect Listening Device

Dec 20, 2012

In my LAN environment, I'm using two cisco SG300-10 switches. Both switches are connected by GE10 on both switches, where both ports are set to trunk.Now on all ports 1-9 on both switches, I'm having client computers attached. So I set ports 1-9 to "access" mode.All interfaces on any switch is left in default vlan.
 
Is it normal that I see all traffic from all connected devices on any port where I connect a listening device?What I'd like to achieve is, that only traffic that is meant for a specific workstation is actually forwarded to this workstation. By now it seems that I get all the traffic from everybody.

View 6 Replies View Related

Cisco :: STP Blocking And Listening Modes

Oct 8, 2012

Sometimes when I enable a switchport I see the port goes to Blocking mode first, not sure if it stays in that mode for the 20 secs, I think sometimes is far less than 20 sec. But I have seen too, that when I enable a port it goes directly to Listening mode. When does a switchport goes to the Blocking mode first, mode that all the books I have read say it should go when you enable a port, and when it goes to Listening mode directly?

View 5 Replies View Related

Cisco WAN :: Router Listening On Public Interface Rv042

Aug 28, 2011

I have two Windows Boxes connected to RV042 ; each has its own static IP assigned to it and each runs bunch of virtual machines , for which I had configured port forwarding .My hosting company claims that my server(s) are listening on IP 192.168.0.1 on a public interface (i.e., one that uplinks to their network). They see this same IP on two different MACs my uplink interface.  I am not really sure how it is possible since 192.168.0.1 was assigned to router itself. 

View 7 Replies View Related

Cisco Firewall :: ASA 5505 Appears To Be Listening On All TCP Ports?

Aug 7, 2011

When I do an NMAP scan against my ASA 5505 on it's internal interface's IP address, it appears to be listening on all TCP ports.  If I do it from across a VPN tunnel, the ports show as open according to NMAP, if I do the scan from the local subnet they show up as unknown. I'm running 8.0.4 code on this ASA.

View 1 Replies View Related

Cisco Switching/Routing :: Switches Listening On 1975 And 2228 / UDP?

Mar 11, 2007

How come many switches show that they are listening on port 2228/udp and 1975/udp? You can see this by running 'show ip sockets'.

View 10 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8968 - Forward External Wan Port Like 49150 To LAN IP On Port 22?

Nov 18, 2012

Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmwae Version : latest
ISP : telecom italia business on ipatm

How to Forward an external wan port like 49150 to lan ip on port 22?In the control pannel I can set only one port , and this port will be the same where the connection will be router to the lan ip ,therefore If I set the port 22 , the connection will be natted to the 22, but how to set a different external port to a specified different lan ip port?

View 1 Replies View Related

TP-Link ADSL2+ Wireless :: TD-8970 Port Forwarding To A Different Internal Port

Mar 7, 2013

Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media

Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.

View 1 Replies View Related

D-Link DIR-655 :: Subsonic Port Forwarding / Get Machine - Port From Outside / Internet

Feb 16, 2011

I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server.  Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening.  However, I can't seem to get to the machine-port from outside/internet. 

I have tried Virtual Server and Port Forwarding with single port.  The server has a stactic IP which I've included in the DHCP range and outside the range.  I have a DSL connection (AT&T), modem only.  I have updated firmware.  I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct.  What am I missing?  Is if possible there is a defect in the router? (don't laugh).  Is there a way to trace a request to that port to see where it is hanging?

(yes, I've STFA, but don't know what else to do).

View 2 Replies View Related

D-Link DIR-655 :: Port Link Light For Powered-off Device Stayed On

Nov 20, 2011

I have a DIR-655 Rev B, in a typical cascaded config:  modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP).  I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture.  Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection.  (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655).  I noticed that the port link light for the powered-off device stayed on on the DIR-655.  When I unplugged the cable from the DIR-655, everything went back to normal.

So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin?  Or Both?  I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.

View 7 Replies View Related

D-Link DIR-655 :: Use Wan Port As 5th LAN Port?

Jul 18, 2011

Is there a way to use the WAN port as a standart ethernet port?

I would like to connect t a 5th computer but I have run out of LAN ports.

View 14 Replies View Related

D-Link DIR-655 :: How To Use USB Port

Feb 22, 2012

D-Link DIR-655 :: How to use USB port

View 14 Replies View Related

D-Link DIR-655 :: WAN Port Is Not Working?

May 19, 2011

Recently, something weird occurred. My Motorola Surfboard cable modem (on PenTeleData/Service Electric) and my D-Link DIR-655 don't seem to be getting along.If I plug a network cable directly from the modem into a computer, it works fine. However, if I go from the modem to the router's WAN port, it doesn't seem to want to connect to the router at all (no matter what DNS settings I change on the router (including spoofing the MAC address of a working computer) or which network cables I use; the "activity" light on both the router and the modem remain off).Also, if I take a network cable and plug one end in one of the LAN ports on the router and the other end in the WAN port, it works (well, the "internet" activity light on the front of the router comes on and the status page at http://192.168.0.1/Status/Device_Info.shtml says "Cable Status: Connected; Network Status: Incorrectly configured - check logs" instead of "Cable Status: Disconnected; Network Status: Disconnected").

View 11 Replies View Related

D-Link DIR-655 :: Can't Port Forward Or Use DMZ

Jan 10, 2011

I can't get any type of port forwarding or DMZ to work with this router. I've checked for double NAT, have a static router IP etc.

I'm using Vista, but I've tried it on a computer with XP as well. I'm using the standard windows firewall, but I also tried disabling it.

I'm using the original 1.10 firmware, I don't know if this is a known issue that was fixed or not.

View 4 Replies View Related

D-Link DIR-655 :: How To Tell LAN Port Speed

Mar 21, 2011

I replaced my old netgear router, which died recently, with a shiny new DIR-655 on my gigabit wired home network. Now I see that file transfer from my NAS is very slow (about 1 megabyte per second). I would like to check if the NAS has connected at 1Gbps to the router. I was browsing the "stat" or "attached device info" in the routers configuration webpage, but could not find it. To be precise, I do see the connection to the NAS, but there is no indication of the connection speed

View 2 Replies View Related

D-Link DIR-655 Can't Port Forward Or Use DMZ

Jan 9, 2011

I can't get any type of port forwarding or DMZ to work with this router.

I made sure to check everything in the sticky before I posted and it all checks out.

I'm using Vista, but I've tried it on a computer with XP as well. I'm using the standard windows firewall, but I also tried disabling it.

I'm using the original 1.10 firmware, I don't know if this is a known issue that was fixed or not.

View 4 Replies View Related

Port Forwarding On D-link DES 1008D?

Feb 9, 2011

How I do it? I know nothing about this stuff... I can't open the ports.

View 1 Replies View Related

D-Link DIR-655 :: Unable To Open Port 21?

Jan 4, 2011

I have a DNS-323 that I can;t get my FTP to work.For some reason no matter what I try I can't open ports on the DIR-655I have the virtual server set as such. [URL]. Checked with open port tool.

View 6 Replies View Related

D-Link DIR-615 :: Can't Connect To Notebook LAN Port

Aug 25, 2011

I was using this router and Malaysia TM UNIFI service. I can use wireless but can't detect the LAN port. I have try it to other modem router and it's working. Its keep showing my local area connection network cable unplugged and no signal at all. And the router was working well on other PC and notebook.Try many way but still can't work

View 3 Replies View Related

D-Link DIR-825 :: Accessing USB Port Outside Of Network?

Aug 22, 2012

If possible I would like to have access to my external hard drive from outside of my network.While in the network my laptop connects to the Hard Drive using the shareport. If I take the laptop with me then I would also have to take the External Drive with me.

View 6 Replies View Related

D-Link DIR-825 :: Possible To Connect External HDD To USB Port For NAS

Apr 3, 2013

I have a DIR-825 Rev. B1 wireless router running FW ver.NA2.0.7. I want to connect a Seagate 4Tb external HDD with USB 3.0 into the USB 2.0 port on the router to use the hdd as a NAS and run backups of the data files on the computers of my home network.   The computers are running Windows 7 - 64bit.  Plugging the hdd into the USB port on the computer lets it be recognized and ensured that Windows 7 had the most current drivers. When I plug the external hdd into the USB 2.0 port on the router and  then plugging in the hdd and resetting the router, I still cannot get the computer to find the hdd on the network. 

View 11 Replies View Related

D-Link DIR-825 :: Port Forwarding On 825 REVB

Dec 27, 2011

I was trying to port forward and could not get it to work. I run a Camfrog room sever of my desktop computer. I needed the TCP port 6005 open to the desktop and UDP ports 5000-15000. I enter that in to the Port forwarding setting but it never work. So later on today I try this I blank out the TCP 6005 in the port forwarding and letf the UDP setting in it and saved it. Then I went to the Virtual server settings and add camfrog3 in the name and put the TCP port 6005 in to it and check it and save the setting and bingo it work.

View 1 Replies View Related

D-Link DIR-615 :: Port Forwarding For Server?

Feb 8, 2012

Alright, so I'm trying to set up a Minecraft server without having to use some sort of hosting program, such as LogMeIn Hamachi. I have tried port forwarding both my external IP from "whatismyip.com" and from ipconfig in the CMD WITH the correct Minecraft port, and others still cannot connect. note that I can only connect to my own server when I use the IPv4 address from my CMD. get my server working so that others can connect? (I have been sure to change my "server properties" file's "server-ip" line accordingly.)

View 1 Replies View Related

D-Link DIR-601 :: Cannot Connect Using Internet Port

May 17, 2011

I am facing a strange problem with my DIR 601 router. I am not able to access internet when I plug in the cable from my model to slot marked nternet' on the back of the model (which I guess is the right way). However, I can access the internet if I plug in the cable coming from modem into any of the 4 ports marked as 'LAN'.

View 2 Replies View Related

D-Link DIR-655 :: Cannot Forward Port 3390

Aug 20, 2011

-hardware: A4
-firmware: 1.34NA,  2010/04/16
-Cable ISP service
-Cable modem without built in router
-wired connection
-Qos is disabled
-I have tried port forwarding and virtual server
-3389 is forwarded fine

I cannot forward port 3390 anymore and I do not remember changing anything.  I am trying to forward port 3390 b/c I already am using remoted desktop on another machine using port 3389 and it works fine.  It is not the machine b/c I change port forwarding machine using 3389 and it works fine, but I need to have 3389 and 3390 set up. 

View 3 Replies View Related

D-Link DIR-655 :: Suddenly No Net On Ethernet Port?

Jan 13, 2011

TWC / Road Runner modem
dir-655 - Hardware Version: B1 
Firmware Version: 2.00NA
dap-1522
windows xp
xbox 360
powerphone voip adapter

Here is my setup:

TWC / RR cable modem to 655
655 port to xp machine
655 port to voip adapter
655 wireless to 1522
1522 port to xbox 360

I am no guru but managed to get all this working about 6 months ago. Other than some TWC outages it has been fine.Couple days back the XP stopped seeing the net. It could still see the LAN. The voip adapter and 1522 / xbox 360 still work fine.Here is what I have tried:

Plugged XP in 1522, worked fine.
Plugged XP directly into cable modem, worked fine.
Plugged XP into port the voip is working on, did not work.
Tried other 3 ports on 655, did not work.

Since the XP machine works with the 1522 and cable modem I am assuming the XP machine is not the problem.Since the voip adapter works on the 655 ports I am assuming the ports are not the problem.

View 2 Replies View Related

D-Link DIR-655 :: No Connection In Internet Port

Apr 7, 2013

I have some questions about DIR-655 want to ask.

1.I use it as a AP, no connection in the internet port, however I only see the DNS setting in the WAN interface, so some url setting can not normally run. Do it has AP mode or other setting that can resolve the DNS.

2.I notice that the Time will suddenly wrong something, even I set it to use local time or ntp.

3.I change the wireless setting to WPA Enterprise, and notice that always disconnect and reconnect, When it is disconnect, notebook and phone can not search the wireless, but ping in local is still alive, log also only show that reconnect, what is happen?

4.I run the internet wizard (not at beginning), I do not change new password in the second phase of wizard, however, after the end of wizard, restart the DIR 655, I can not use the password I set before to login and also I try to leave blank in password flied, it also failed, I use the same password in the user(not admin), I can login, is it the bug of wizard, if this situation need to reset the router, can I take the config first?

View 10 Replies View Related

D-Link DIR-655 :: Could Not Get Port Forwarding Working

Feb 11, 2011

I setup port forwarding for many router before, but I couldn't get this one to work.I triple check all of my configuration, they all setup correctly. But the port/ports on the router is not open.

View 1 Replies View Related

D-Link DIR-655 :: Share Port And Windows 8

Apr 30, 2013

I have noticed that the Share port software is available for Windows 7 which I do use on my Windows 7 computer.

If I get a Windows 8 computer, does the same software also work on Windows 8 ? ? ?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved