D-Link DIR-655 :: WAN Port Is Not Working?
May 19, 2011
Recently, something weird occurred. My Motorola Surfboard cable modem (on PenTeleData/Service Electric) and my D-Link DIR-655 don't seem to be getting along.If I plug a network cable directly from the modem into a computer, it works fine. However, if I go from the modem to the router's WAN port, it doesn't seem to want to connect to the router at all (no matter what DNS settings I change on the router (including spoofing the MAC address of a working computer) or which network cables I use; the "activity" light on both the router and the modem remain off).Also, if I take a network cable and plug one end in one of the LAN ports on the router and the other end in the WAN port, it works (well, the "internet" activity light on the front of the router comes on and the status page at http://192.168.0.1/Status/Device_Info.shtml says "Cable Status: Connected; Network Status: Incorrectly configured - check logs" instead of "Cable Status: Disconnected; Network Status: Disconnected").
View 11 Replies
ADVERTISEMENT
Feb 11, 2011
I setup port forwarding for many router before, but I couldn't get this one to work.I triple check all of my configuration, they all setup correctly. But the port/ports on the router is not open.
View 1 Replies
View Related
Jul 12, 2011
RDP (port 3389) is not working on D-Link network - is there a setting in the d-link to allow this?
View 4 Replies
View Related
Nov 30, 2012
None of the port forwarding settings are working at all on my router. I have just a couple very simple settings. One of them is just an IP camera. I input the name, the TCP port, the computer (IP address) and that's it. This works just fine with my other Netgear router, but with this router, NADA. The router has the latest version of the firmware applied. Just applied it. Hardware version B. Firmware version: 2.10NA. If so, then I really need my money back since it is a main function of a router and it should work. Can't return it now, since I bought it several months ago. Never knew port forwarding didn't work because I never needed it until now.
View 6 Replies
View Related
Mar 3, 2011
I was changing the port forwarding configuration when suddenly the router stopped working, and now the "D-Link" light is constantly on, and the power light and the 4 LAN lights are flashing. Nothing worked, resetting, or unplug and plug again in a short time.
I disconnected it for 12 hours, and when I plugged in again, it kinda worked, and the settings where factory defaults, so when I tried to connect it to DSL via PPoE, when ( I believe ) it reboots to accept the changes, it starting flashing again and completely stopped working.
So I waited 12 hours more unplugged, plugged it and it worked, and the setting from 12 hours earlier were still there. But when trying to connect to the DSL it stopped working AGAIN.
Now I don't know what to do. I guess I am going to keep trying connecting with little differences, until something.
I believe it still has warranty but since the is no official service in Uruguay, it isn't economically viable to send it overseas.
I am currently connected directly to the DSL, sharing connection to other computers through a switch and hosting an ad-hoc wireless network, but the performance is terrible and the wireless range is minimal.
View 1 Replies
View Related
Mar 17, 2013
Taking another look at Dview cam today after not touching it for 3 months after initial install.The dcs-2132L can't connect.I can to the 2132L directly... I changed the port as a test.. Port 80 wasn't working originally.
[url]....
View 9 Replies
View Related
Feb 25, 2013
Region : Malaysia
Model : TD-W8968
Hardware Version : V1
Firmware Version : 0.6.0 1.1 v0005.0 Build 120926 Rel.27100n
ISP : TM
The Remote Management Port is not working correctly. For whatever port I set, it will uses port 80 to access.
View 2 Replies
View Related
Jan 8, 2013
Region : Greece
Model : TD-W8961NB
Hardware Version : V2
Firmware Version : 2.0.0 120823
ISP : otenet
The problem is that the voip is not working. I have 2 offices with adsl connection. A is the central office and B is the branch office. The installation is old with deferent ADSL modem-router(Zyxel). The zyxel at the A office was damaged so i had to change it with Tp-link. The potology with ip and cables is the same. I tested the port forward for voip (port 1720) with telnet from outside of the office and responds correct. When i try to call from the A office to B office it seems that i can not connect. When i call from B office to A office the phone is ringing and i can not hear office B but office B hear office A. When i use the old modem router at the office A everything is working fine but the modem-router works just for a while so i have to change it. I closed the firewall but the problem is still the same. I talked with the local distributor and they tolded me that i have to correct the configuration. At the interface setup is chosen the dynamic at the section get ip and not static as i should do. The is a problem there. The configuration asks me the subnet mask and gateway. I do not know the subnet mask and either the local distributor and the local internet provider cannot assist. The internet provider told me to use at the subnet mask 255.255.255.240 and at the gateway the ip of the router. I did that but when i did i lost the internet connection. I have to mention that i make some other port forwards to my SBS2003 server and like remote desktop, vpn connections and https that works fine. The only prolbem is with the vpn port forwarding.
View 4 Replies
View Related
Jul 3, 2012
There is no "blinking light" indication on my E3000 at the Internet (Yellow label) and Ethernet port no 4. I tried plugging in 2 cables at all of the ports. I got the blinking indication at Port 1 through 3. The same cable's have no response at Port 4 and Internet port. As a result my I am not able to connect to the internet.
View 2 Replies
View Related
Nov 18, 2012
Region : Italy
Model : TD-W8968
Hardware Version : V1
Firmwae Version : latest
ISP : telecom italia business on ipatm
How to Forward an external wan port like 49150 to lan ip on port 22?In the control pannel I can set only one port , and this port will be the same where the connection will be router to the lan ip ,therefore If I set the port 22 , the connection will be natted to the 22, but how to set a different external port to a specified different lan ip port?
View 1 Replies
View Related
Mar 7, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
View 1 Replies
View Related
Feb 16, 2011
I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
(yes, I've STFA, but don't know what else to do).
View 2 Replies
View Related
Nov 20, 2011
I have a DIR-655 Rev B, in a typical cascaded config: modem > dir-555 > switches & devices, etc.One of the four dir-655 ports is connected to a cheap-o Belink Wifi router which I use as an access point (I only use this because there's one device that only supports WEP). I was debugging a WiFi issue and I pulled the plug on this Belkin just to get it out of the picture. Well, when I did that, EVERYTHING that was connected through the DIR-655 lost connection. (Well, all the wired stuff anyway- not sure about WiFi devices through the DIR-655). I noticed that the port link light for the powered-off device stayed on on the DIR-655. When I unplugged the cable from the DIR-655, everything went back to normal.
So what I'm trying to figure out now is, is this a DIR-655 issue, or is it something screwy with the Belkin? Or Both? I've got to assume that there's some inherent flaw in the DIR-655 that allows something connected to a port to screw up everything that it's hosting.
View 7 Replies
View Related
Jul 7, 2012
I am trying to make a server in the game Halo combat evolved for the PC, but i need to forward 3 ports, ports: 80, 2302, and 2303, i did them all, but it still says they are all still closed, when I scan them or they say, its times out.I have a D-Link router.
View 5 Replies
View Related
Sep 30, 2012
I built a pc asrock z77 pro3 mobo, i5 3570k 3.4ghz, ati 7950, 8gb kingston ddr3 1600mhz ram, corsair 650w psu, a hyper 212 evo and a 500gb hdd with a 128gb ssd all in a cm haf912 case.My problem is that everything works fine except for the inbuilt gigabit lan port. I'm accessing the net through an old pci-e slot network card i found, and I'd really like to use the inbuilt gigabit port. The realtek drivers do not appear under device manager. I installed the latest network drivers from asrock - (Realtek Lan driver ver:7048 for 64-bit win 7), I tried various things I read online like removing the ram for a few minutes, disabling the NIC and sleep mode. I always get this message when installing the driver: "Realtek ethernet cable was not found if deep sleep mode is enabled plug the cable" I've done everything I've read online and from reformatting to removing the ram.In the bios, i made sure the adapter was enabled. another thing is that there is no light coming from the port when the lan cable is inserted into the port. there is a light from the pci adapter so i'm not sure if it's faulty. I've also checked that the cables are fine. I hooked them up to my macbook and ps3 and the network was fine.
View 1 Replies
View Related
Jun 20, 2012
i have a DSL-2730U WIRELESS N 150 ADSL2+ 4-PORT ROUTER which i have been using for the past 2 months.It was working fine,but since the last 5 days when i plug the lan wire into the PC port, nothing happens...it doesn't get recognized..the green light in the port is always glowing..i've tried another cable..same problem...i've tried it on another laptop..it works FINE....
View 1 Replies
View Related
Jul 2, 2011
My custom built desktop is not recognizing an ethernet cord. The lights are not coming on when I plug it in. The device manager does not show network adapters. Im not sure where to find it/ not sure its there.
View 6 Replies
View Related
Oct 27, 2011
I had an old linksys router running DDWRT. I bought a new Asus RT-N16 and finally set it up. I had to just duplicate the settings by hand as you cannot back them up across different hardware models even though both are running DDWRT.
I hooked up the new router and everything was working great, until I decided to check one of my port forwards. Turns out its not working, I can't connect through my DynDNS assigned dns name. Assuming I configured something wrong, I compared the settings of the two routers. Nothing interesting, it is set up right.
From there I decided to just hook the old router up, assuming I overlooked something. So I mess around with all the cables, and then, to my surprise, IT STILL DIDN'T WORK.
A few points of interest:My Static IPS are set up right. My server has the proper IP My home IP did not change. DynDns has the right IP. I rebooted all the network equipment and server... just for the hell of it. I tried changing a port forward to point to my main PC and that failed too.
View 10 Replies
View Related
Nov 28, 2012
Here's the version of the ios i'm running:Cisco Adaptive Security Appliance Software Version 8.0(4)The issue i'm encountering seems to stem from the use of port rangesThe client states that while a port range is included within the running config, nmap tests within the server indicate that port as closed. Below is the list of port ranges being opened within the ASA[CODE]
View 1 Replies
View Related
Feb 20, 2013
I want to setup port forwarding in my office router so that i can access my lan computer (192.168.0.122) from any where in the world through (remote desktop connection)I have (D-Link (DIR-615)) router. I went to virtual server option. then i select application name as Remote desktop then public port as (3389), protocol (both), Schedule (Always).My lan computer ip address (192.168.0.122), private port (same 3389), inbound filter (allow all). then i clicked save settings. Then the router took 20 seconds to save. then i close the browser.Then i asked my brother to connect through remote desktop connection who is on the skype and he is in different country and that time he is in office. So he put my router public ip address (xxx.xxx.xxx.xxx:3389) in this format but unable to connect.
View 2 Replies
View Related
Nov 22, 2011
I recently installed Arkham City on my computer played it for a while, tried google chrome, gave me a corrupt profile error or something (internet still worked and was connected at the time) restarted my computer and now it's telling me there isn't an ethernet cable connected to my computer.
Here's what I tried so far:
-Uninstalling and reinstalling the driver
-Updating the driver
-Using the network troubleshooting for windows 7
-Doing a system restore before I installed the game (gave me an error saying could not complete restore)
-Currently scanning my computer in safe mode with networking (seeing if that might work, doesn't) with malewarebytes
-Unplugged and replugged the router and modem
-Checked the router on another computer to see if there's a connection (there is none)
-Checked the router to see if there is a light in the port connected to the ethernet, it's blinking at a very slow a steady pace, unlike the ones around it which are solid green lights
-Tried the ethernet cable on another computer, works fine.
computer specs:
Windows 7 64-bit home premium edition
Gigabyte GA-MA790X-UD4P
NETGEAR router WNDR3700
View 2 Replies
View Related
Jun 23, 2011
I have a DSL modem (custom made and branded by my ISP) which is receiving a DSL stream... it has an external IP which is visible to the world, say, 11.22.33.44 ... This modem has DHCP enabled, has an internal IP for itself, which is 192.168.1.1 .. it is connected to 2 laptops via and ethernet cable .. Laptop 1 has IP 192.168.1.2, and Laptop 2 has IP 192.168.1.3 ...On Laptop 1, two applications are running, jDownloader and Media Player Classic, which have their web interfaces on ports 8765 and 13579,respectively.. I can access both of these web interfaces from Laptop 2 by opening these addresses: 192.1681.2:8765 and 192.168.1.2:13579 ... both of their web interfaces open up, meaning the web interfaces are working fine ..Moving on, I now want to access these web interfaces from outside my network as well, and so I've configured port forwarding in my DSL modem to forward all traffic on ports between 8000 and 14000 (both TCP and UDP) to IP 192.168.1.2 ... I have verified that port forwarding is working by testing it using PortForward.com's port checker tool, and this website too: Open Port Check Tool - Test Port Forwarding on Your Router When I use the website, if I'm running the applications on Laptop 2, the website reports that the port is open .. if I then close the application, the website reports the port is closed ... This makes sense as nothing is listening on my machine in the latter case .. Also, if I disable port forwarding in my modem, again, the website reports the port is closed ... so, the website's results seem to be okay ...
Despite the above tools reporting that port forwarding is working, I am unable to open the web interfaces from outside my network ... So for example, if I tried to browse 11.22.33.44:8765 or 11.22.33.44:13579, nothing opens in my browser ... But if I accessed these web server's locally from Laptop 3, by typing in 192.168.1.2:8765 or 192.168.1.2:13579, they opened ... The tools report unanimously that port forwarding is working, and yet I am unable to open the web interfaces from outside the network ..Also note that I have disabled the firewall from my computer, and have also made sure that any option in the above programs (whose web interfaces I am trying to open) that says only local connections are to be accepted, is disabled ...
View 2 Replies
View Related
Mar 5, 2012
I was having a cleanup of the desk and unplugged the cable shortly, and after plugging it back in it could no longer find any connection. The only way I seem to be able to get connected to the internet now is to run a cable to my ethernet switch, and then onwards to my computer itself. Even when doing this the net seems to be very slow, won't connect through Chrome etc or just flat out won't connect.
View 5 Replies
View Related
Oct 10, 2012
I'm trying to set up a Minecraft server so I can appear to be a hero to my 8 year old son. I have to forward a port to 25565 adn I've followed all the instructions on how to do this on my netgear DGND3700v2. I've also turned off my Windows 7 firewall, but when I go to a test website, I still get a message saying the port is closed. I don't have a static IP address, is this absolutely critical or does it just mean that the boys will have to log on to a new IP address each time they want to play?
View 1 Replies
View Related
Jan 9, 2013
My modem/router is Riger and model is DB108-WL. I had set Port Forwarding in my modem/router configuration page using web [URL] had disable the uPNP setting in both the modem/router and camera setting page. Besides, also disable the firewall on the modem/router and on my laptop (Windows firewall and McAfee antivirus)My camera static IP address details are listed as below:
IPv4 Address: 192.168.1.8
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
Primary DNS: 192.168.1.1
Port number: 8080
I am able to access my IP Camera using local LAN network by using web [URL] but unable to access from external network WAN using internet by using web http://*External IP Address*:8080 My ISP provide a dynamic external IP address so my external IP Address will change each time I connect to internet network. To trace this, I used IPchicken website IP Chicken - Whats my IP address? ip address lookup to identify my modem/router Public IP address. I used my smartphone to access this external IP Address in order to prevent NAT Loopback issue but still can not access.
1) Do I need to have my host computer turn on at home in order for me to access the IP Camera from external WAN network which is internet from anywhere outside? Or just turn on my modem/router and IP Camera will do?
2) I had read a lot of blogs and forums from the past 2 weeks about Port Forwarding. From one of the forum, it mentioned need to setup 2 ports for Port Forwarding in order to get IP Camera access from external network. One for web interface which use port 80 and another one for video streaming which is port 1024. So, is it true for every IP Camera to configure 2 ports forwarding in order to get access from external network?
3) If I can access the IP Camera from local LAN network, does it mean my laptop Windows firewall and McAfee antivirus setting is ok for access from external network?
4)Is it a reliable method to use smartphone as a test to try out whether my setting is ok to access the IP Camera from external network? My smartphone is Android 2.3 OS and able to access the IP Camera when connected to my modem/router using WIFI (local LAN access). When key in external IP address using 3G network, it can not access.
View 19 Replies
View Related
Sep 7, 2012
I'm having a problem with port forwarding on my 1941W router.I would like to forward ports 8001 and 2001 TCP from Internet to a local host on the internal network.I am able to connect to the local host from the internal network, but it does not work from the Internet.
Here is my config:
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router1
[code].....
View 1 Replies
View Related
Mar 13, 2011
We are try to connect ssh via outside system (from Internet) its was not getting connected.
When we try to connect from outside pool of ip than its working.
View 1 Replies
View Related
Oct 16, 2011
We just purchased 8 managed switches POE to swap out our existing in preparation for our new phone system. We installed them all after configuring with static IP. Deployed... and all but two work fine. Any tips for troubleshooting why two of them do not work? There are a couple other switches in the building. Could it be that a switch "upstream" from the two non-functioning switches is causing an issue? If so, how do I find out? When we put back the two "dumb" switches all was fine.
View 1 Replies
View Related
Oct 12, 2012
I'm a newbie in wireless, recently I got a WLC2006 and AP1130 - IOS: 12.4(10b)JDE
- The AP has been changed LAP mode already
- AP-manager port and management port are PORT 4
- I have configured the WLC's "Internal DHCP server"...
When I plug the AP to WLC port 2 and 3, it can get the IP address from DHCP however, when I plug it to WLC port 1, it gets nothing. and the IP address is 0.0.0.0
Does it mean the port is damaged already? Or can I do anything to check or enable the port 1 again?
View 4 Replies
View Related
Feb 27, 2011
Based on the business requirement, I have installed one more 9 port FE Switch in addition to existing one, NM is discovered but when we connect PC or IP-Phone it is not working, current IOS is flash:c2800nm-advipservicesk9-mz.124-3h.bin with 64MB Flash
View 5 Replies
View Related
Feb 21, 2012
Port Forwarding Bug - Working but not working? I'm so pissed as I've been working on it for hours and it still doesn't work. The only additional information apart from the ones located in the link is that in the security log something about the NTP.
View 4 Replies
View Related
Dec 4, 2012
I have a Netgear wnr2000v3 Router connected to my Motorola Surfboard Gateway.I have a freePBX Server (virtual running off of VMware Workstation 8) that needs ports 10001-20000 and 5060 forwarded to the server at 192.168.1.110
I added the portforwarding as in this photo:
When I use a port tester it still says "Port 5060 is closed"I have also turned off Windows Firewall. What else could be blocking these ports?
View 3 Replies
View Related
Oct 17, 2011
I have the Asus P5QL-VM DO motherboard.On the Ethernet port the lights are not working and I can not get an internet connection.
View 1 Replies
View Related
