D-Link DIR-655 :: None Of Port Forwarding Settings Are Working At All On Router
Nov 30, 2012
None of the port forwarding settings are working at all on my router. I have just a couple very simple settings. One of them is just an IP camera. I input the name, the TCP port, the computer (IP address) and that's it. This works just fine with my other Netgear router, but with this router, NADA. The router has the latest version of the firmware applied. Just applied it. Hardware version B. Firmware version: 2.10NA. If so, then I really need my money back since it is a main function of a router and it should work. Can't return it now, since I bought it several months ago. Never knew port forwarding didn't work because I never needed it until now.
View 6 Replies
ADVERTISEMENT
Feb 11, 2011
I setup port forwarding for many router before, but I couldn't get this one to work.I triple check all of my configuration, they all setup correctly. But the port/ports on the router is not open.
View 1 Replies
View Related
Mar 3, 2011
I was changing the port forwarding configuration when suddenly the router stopped working, and now the "D-Link" light is constantly on, and the power light and the 4 LAN lights are flashing. Nothing worked, resetting, or unplug and plug again in a short time.
I disconnected it for 12 hours, and when I plugged in again, it kinda worked, and the settings where factory defaults, so when I tried to connect it to DSL via PPoE, when ( I believe ) it reboots to accept the changes, it starting flashing again and completely stopped working.
So I waited 12 hours more unplugged, plugged it and it worked, and the setting from 12 hours earlier were still there. But when trying to connect to the DSL it stopped working AGAIN.
Now I don't know what to do. I guess I am going to keep trying connecting with little differences, until something.
I believe it still has warranty but since the is no official service in Uruguay, it isn't economically viable to send it overseas.
I am currently connected directly to the DSL, sharing connection to other computers through a switch and hosting an ad-hoc wireless network, but the performance is terrible and the wireless range is minimal.
View 1 Replies
View Related
Jan 8, 2013
Region : Greece
Model : TD-W8961NB
Hardware Version : V2
Firmware Version : 2.0.0 120823
ISP : otenet
The problem is that the voip is not working. I have 2 offices with adsl connection. A is the central office and B is the branch office. The installation is old with deferent ADSL modem-router(Zyxel). The zyxel at the A office was damaged so i had to change it with Tp-link. The potology with ip and cables is the same. I tested the port forward for voip (port 1720) with telnet from outside of the office and responds correct. When i try to call from the A office to B office it seems that i can not connect. When i call from B office to A office the phone is ringing and i can not hear office B but office B hear office A. When i use the old modem router at the office A everything is working fine but the modem-router works just for a while so i have to change it. I closed the firewall but the problem is still the same. I talked with the local distributor and they tolded me that i have to correct the configuration. At the interface setup is chosen the dynamic at the section get ip and not static as i should do. The is a problem there. The configuration asks me the subnet mask and gateway. I do not know the subnet mask and either the local distributor and the local internet provider cannot assist. The internet provider told me to use at the subnet mask 255.255.255.240 and at the gateway the ip of the router. I did that but when i did i lost the internet connection. I have to mention that i make some other port forwards to my SBS2003 server and like remote desktop, vpn connections and https that works fine. The only prolbem is with the vpn port forwarding.
View 4 Replies
View Related
Sep 6, 2011
I did read the thread entitled ''WRT160N Can't save settings'', but I believe this might be different. My router is actually communicating with my computer (physically plugged in), since I can save all other settings EXCEPT the port-fowarding ones.I am trying to save settings for a gaming application in the Single Port Forwarding section of my router settings. After clicking both ''save settings'' and ''continue'', it simply returns to the Single Port Forwarding section, except everything is blank, as though nothing was saved.
Here are my specs:
WRT160Nv1
Firmware Version: v3.0.03
Here are the steps I have already undertaken:
1- Erase browser cache and cookies
2- Updated to latest firmware (v3.0.03), 10-second reset button, 20-second power cycle.
View 1 Replies
View Related
Jul 18, 2012
I am trying to run a server for minecraft, which some of you may know primarily uses Port 25565. I have tried everything that I've seen suggested. I have a Linksys WRT54GS router that I have my 2 xboxes, playstation 3, pc, and wii connected to. Now, I don't use any of these components at the same time. I had an issue with my xbox and the game "Black Ops", where my NAT type was strict, but a microsoft support technician walked me through port forwarding for the xbox, and it worked. My NAT type was displayed as "open" now. This is not the case with Port 25565 however, as even though I've port forwarded 25565 to my static IP i set up for my PC (which is my server PC), Port checking sites such as "Yougetsignal" and a couple of others are still showing no connection for the current external IP and Port 25565.
I went through ipconfig in windows "cmd" and made sure I had all the ip's and subnets and dns' and whatnot correctly entered in my routers configuration page. I went into Windows firewall and put new rules for port 25565 into incoming rules. None of this seems to work. I even shut off the firewall completely (temporarily, mind you), just to eliminate that possibility, to no avail. Still getting negative responses from these sites. I am able to log into my server myself, using "localhost" as the address, but none of my minecraft buddies can get on my server. I've also tried to use Hamachi to set up a server, which doesn't need ports to be forwarded, but although they can join my hamachi network, they can't join the server. Obviously there is more of a problem than just not being able to open ports, and I am at a loss.
Also, I am aware that my external IP, given by my ISP, will change with every disconnect and reconnect of my signal. I got my current IP address during this time and gave that to my buddies so they could join the non-hamachi network. For the Hamachi server I edited my Hamachi network IP into my server software's properties file, where as it would be left blank for my non-hamachi server.
View 4 Replies
View Related
Nov 30, 2012
I upgraded to a 6500 from a e4200. I use ports 81-84 on test web servers set to static Ip,s when I open the ports nothing can get through from the outside. I can hit the pages internally on those ports and IP's but not from my external ip to those ports. When I set my old router everything is fine.
View 9 Replies
View Related
Jan 2, 2013
I set up port forwarding on my router. When I go to canyouseeme.org and put in my public IP address (I can ping the IP address with no issues) and the port that I'm forwarding it says it can't hit the port.
View 2 Replies
View Related
Dec 12, 2011
I've read over the FAQ and followed the normal instructions for port forwarding, but can't seem to get it to work with this particular router, E2500. I have tried both the single port forwarding and the multi port range forwarding, and neither works. I've tried an older WRT54G router and port forwarding works fine on it, so I know it's not my ISP.
View 4 Replies
View Related
May 11, 2013
RV215W router port forwarding not working.Port forwarding works for a short period of time, then stops working. Reboot router, works again for short period of time, then stops again.
I have updated firmware to latest. I had seen other similar bugs posted for 220 and I think 180, not sure if this router has similar bugs and waiting for fix release to firmware.I had recently purchased two, one deployed, will hold off on other now because of issues, and may have to move to different unit if a resolution not found this week.
View 5 Replies
View Related
Jan 16, 2010
Having a problem with port forwarding on their WRT400N? I'm forwarding one service (https) and this stops working if it's not accessed after a 10 days or so. The only way to get it to work again is to reboot the router. I’m running the “latest" firmware, which is an oxymoron considering it's been over 12 MONTHS since Linksys updated the code... Which is appalling considering this appears to be their flagship wireless N router.
View 5 Replies
View Related
Oct 17, 2011
I currently have an E1200. I can port forward single ports, but when I attempt to forward a range of ports it doesn't work and there is no error in the log.
Specifically I am port forwarding RTP ports (10000 - 20000). I am aware of the security risks, please do not preach.
View 1 Replies
View Related
Jan 8, 2010
I have DIR-615, connected via ethernet. I enabled port forwarding for Quake 3, using the range of 27660-27980 to account for custom server ports. Set schedule to "always" although also did "never" but it didn't make a difference. I checked the FAQs for frequent resets vis a vis application outbound requests, which recommended disable uPnP and this had no effect. Symptom: when Quake 3 attempts to connect to the Master Server, the router resets all connections, LAN and WLAN. It takes approximately 30 seconds to regain connection to WAN, although LAN does not drop. Also during this time, the world sigil on the router itself turns orange. This is the only time this happens, when trying to play Quake 3. Previous router to this one was Linksys (by Cisco) BEFSR41, in which simply setting up port forwarding for the client IP address allowed connection. I can find no particular reason why the router resets all interfaces when blocking a port, if it is indeed the firewall triggering this.
Other infos:
Model: Wireless N 615, DHCP enabled on both sides
LAN connect: Category5 to 10/100 NIC onboard to Intel 865GBF
Client firewall: none
Client OS: Windows XP Professional SP3
View 6 Replies
View Related
Oct 23, 2011
I'm trying to configure port forwarding for FTP but in my case it isn't as simple as i assumed ... i have an actiontec router/modem that serves as incoming internet from my provider (FIOS), which i connected to my own router (dir-825). i mainly configure my network on the dlink and leave the actiontec alone.
[CODE]...
View 13 Replies
View Related
Jul 29, 2011
I currently use a D-Link DIR-655 router on a game server I run and I've been having this problem for sometime now. I have the router hooked up to the internet modem, and then my server computer hooked up to the router's first port. I use port forwarding to forward the game ports, as well as my FTP server ports. I have about 80 clients or so logged in at a time on my server.The issue is the following. Our internet connection has an external IP of 67.23.155.123 (this is just an example). My internal IP is 192.168.0.101.When I do "netstat" to see all the clients logged in to the game server on this computer or when I run Wireshark, every client logged in to the server (for this game application) is shown as having an IP of 67.23.155.123 (the server's external IP).On the other hand, for our FileZilla FTP server, if I run Wireshark/netstat, I can actually see the client's external IP (i.e. each individual IP of people logged into the FTP).If I hook up the server directly to the internet modem, this isn't a problem, and I am able to correctly see the IP of each client logged in to the game server individually.
View 12 Replies
View Related
May 24, 2012
I have a broadband connection and recently I bought a new D-Link wireless router for accessing internet on my Android phone via Wi-Fi. Router model no. is N 150 DIR-524.After configuring it was working fine for a week or so and then one fine day internet stopped working on my PC and router LED for internet was not glowing as well. So I called my ISP and they changed my ethernet card settings (nVidia).They changed the 'Speed/duplex settings' from 'Auto Negotiation' to '10 Mb Half Duplex' and then the internet started working. During this they had disconnected my router. Once they were gone, I reset the router and connected it back. Since then it ain't working Internet works fine when the cable is plugged directly in the ethernet card but doesn't work when plugged via router. Router does everything right from opening the '192.168.0.1' page to saving the settings. But there's no internet access.
View 8 Replies
View Related
Jan 24, 2013
Region : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version : TL-MR3420_V2_121206
ISP : 3
I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.
View 14 Replies
View Related
Jul 21, 2012
I have the DCS-930L camera. I need to know how to setup port forwarding/triggering on my router, which is a Cisco DDR2200 CL. I understand that in order to use the camera, i need to do this. how to set up NAT.
View 1 Replies
View Related
Jul 7, 2012
I am trying to make a server in the game Halo combat evolved for the PC, but i need to forward 3 ports, ports: 80, 2302, and 2303, i did them all, but it still says they are all still closed, when I scan them or they say, its times out.I have a D-Link router.
View 5 Replies
View Related
Oct 27, 2011
I had an old linksys router running DDWRT. I bought a new Asus RT-N16 and finally set it up. I had to just duplicate the settings by hand as you cannot back them up across different hardware models even though both are running DDWRT.
I hooked up the new router and everything was working great, until I decided to check one of my port forwards. Turns out its not working, I can't connect through my DynDNS assigned dns name. Assuming I configured something wrong, I compared the settings of the two routers. Nothing interesting, it is set up right.
From there I decided to just hook the old router up, assuming I overlooked something. So I mess around with all the cables, and then, to my surprise, IT STILL DIDN'T WORK.
A few points of interest:My Static IPS are set up right. My server has the proper IP My home IP did not change. DynDns has the right IP. I rebooted all the network equipment and server... just for the hell of it. I tried changing a port forward to point to my main PC and that failed too.
View 10 Replies
View Related
Mar 7, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
View 1 Replies
View Related
Feb 16, 2011
I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
(yes, I've STFA, but don't know what else to do).
View 2 Replies
View Related
Feb 20, 2013
I want to setup port forwarding in my office router so that i can access my lan computer (192.168.0.122) from any where in the world through (remote desktop connection)I have (D-Link (DIR-615)) router. I went to virtual server option. then i select application name as Remote desktop then public port as (3389), protocol (both), Schedule (Always).My lan computer ip address (192.168.0.122), private port (same 3389), inbound filter (allow all). then i clicked save settings. Then the router took 20 seconds to save. then i close the browser.Then i asked my brother to connect through remote desktop connection who is on the skype and he is in different country and that time he is in office. So he put my router public ip address (xxx.xxx.xxx.xxx:3389) in this format but unable to connect.
View 2 Replies
View Related
Jun 23, 2011
I have a DSL modem (custom made and branded by my ISP) which is receiving a DSL stream... it has an external IP which is visible to the world, say, 11.22.33.44 ... This modem has DHCP enabled, has an internal IP for itself, which is 192.168.1.1 .. it is connected to 2 laptops via and ethernet cable .. Laptop 1 has IP 192.168.1.2, and Laptop 2 has IP 192.168.1.3 ...On Laptop 1, two applications are running, jDownloader and Media Player Classic, which have their web interfaces on ports 8765 and 13579,respectively.. I can access both of these web interfaces from Laptop 2 by opening these addresses: 192.1681.2:8765 and 192.168.1.2:13579 ... both of their web interfaces open up, meaning the web interfaces are working fine ..Moving on, I now want to access these web interfaces from outside my network as well, and so I've configured port forwarding in my DSL modem to forward all traffic on ports between 8000 and 14000 (both TCP and UDP) to IP 192.168.1.2 ... I have verified that port forwarding is working by testing it using PortForward.com's port checker tool, and this website too: Open Port Check Tool - Test Port Forwarding on Your Router When I use the website, if I'm running the applications on Laptop 2, the website reports that the port is open .. if I then close the application, the website reports the port is closed ... This makes sense as nothing is listening on my machine in the latter case .. Also, if I disable port forwarding in my modem, again, the website reports the port is closed ... so, the website's results seem to be okay ...
Despite the above tools reporting that port forwarding is working, I am unable to open the web interfaces from outside my network ... So for example, if I tried to browse 11.22.33.44:8765 or 11.22.33.44:13579, nothing opens in my browser ... But if I accessed these web server's locally from Laptop 3, by typing in 192.168.1.2:8765 or 192.168.1.2:13579, they opened ... The tools report unanimously that port forwarding is working, and yet I am unable to open the web interfaces from outside the network ..Also note that I have disabled the firewall from my computer, and have also made sure that any option in the above programs (whose web interfaces I am trying to open) that says only local connections are to be accepted, is disabled ...
View 2 Replies
View Related
Oct 10, 2012
I'm trying to set up a Minecraft server so I can appear to be a hero to my 8 year old son. I have to forward a port to 25565 adn I've followed all the instructions on how to do this on my netgear DGND3700v2. I've also turned off my Windows 7 firewall, but when I go to a test website, I still get a message saying the port is closed. I don't have a static IP address, is this absolutely critical or does it just mean that the boys will have to log on to a new IP address each time they want to play?
View 1 Replies
View Related
Jan 9, 2013
My modem/router is Riger and model is DB108-WL. I had set Port Forwarding in my modem/router configuration page using web [URL] had disable the uPNP setting in both the modem/router and camera setting page. Besides, also disable the firewall on the modem/router and on my laptop (Windows firewall and McAfee antivirus)My camera static IP address details are listed as below:
IPv4 Address: 192.168.1.8
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
Primary DNS: 192.168.1.1
Port number: 8080
I am able to access my IP Camera using local LAN network by using web [URL] but unable to access from external network WAN using internet by using web http://*External IP Address*:8080 My ISP provide a dynamic external IP address so my external IP Address will change each time I connect to internet network. To trace this, I used IPchicken website IP Chicken - Whats my IP address? ip address lookup to identify my modem/router Public IP address. I used my smartphone to access this external IP Address in order to prevent NAT Loopback issue but still can not access.
1) Do I need to have my host computer turn on at home in order for me to access the IP Camera from external WAN network which is internet from anywhere outside? Or just turn on my modem/router and IP Camera will do?
2) I had read a lot of blogs and forums from the past 2 weeks about Port Forwarding. From one of the forum, it mentioned need to setup 2 ports for Port Forwarding in order to get IP Camera access from external network. One for web interface which use port 80 and another one for video streaming which is port 1024. So, is it true for every IP Camera to configure 2 ports forwarding in order to get access from external network?
3) If I can access the IP Camera from local LAN network, does it mean my laptop Windows firewall and McAfee antivirus setting is ok for access from external network?
4)Is it a reliable method to use smartphone as a test to try out whether my setting is ok to access the IP Camera from external network? My smartphone is Android 2.3 OS and able to access the IP Camera when connected to my modem/router using WIFI (local LAN access). When key in external IP address using 3G network, it can not access.
View 19 Replies
View Related
Sep 7, 2012
I'm having a problem with port forwarding on my 1941W router.I would like to forward ports 8001 and 2001 TCP from Internet to a local host on the internal network.I am able to connect to the local host from the internal network, but it does not work from the Internet.
Here is my config:
version 15.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname Router1
[code].....
View 1 Replies
View Related
Dec 3, 2012
I have TL-WR740N router. ISP should provide me up to 100Mb/s internet speed. Actual measurements shows me about 80 Mb/s. The problem is when I enable 3389 port in Port Triggering my internet speed drops to 2,5 Mb/s. When I disable port triggering, speed become normal again.
View 3 Replies
View Related
Feb 21, 2012
Port Forwarding Bug - Working but not working? I'm so pissed as I've been working on it for hours and it still doesn't work. The only additional information apart from the ones located in the link is that in the security log something about the NTP.
View 4 Replies
View Related
Dec 4, 2012
I have a Netgear wnr2000v3 Router connected to my Motorola Surfboard Gateway.I have a freePBX Server (virtual running off of VMware Workstation 8) that needs ports 10001-20000 and 5060 forwarded to the server at 192.168.1.110
I added the portforwarding as in this photo:
When I use a port tester it still says "Port 5060 is closed"I have also turned off Windows Firewall. What else could be blocking these ports?
View 3 Replies
View Related
Feb 6, 2012
I have a licensing server. Other computers need to turn on a program, they send a message to the licensing server, and it responds that they have permission to run.Until today the licensing server was plugged into its own ethernet wall socket and configured with a static IP address. Today I put a router into that wall socket and now the server's plugged into the router.The router (WRT-54G) was set to the static IP - and now the internet on its network works. I set all ports to be forwarded to the server's internal IP address - and now my programs can detect and ping it. But now the server won't send back permissions to use licensed software, or even reply with a list of the software which it can license.
View 1 Replies
View Related
Dec 5, 2011
I have some hardware on my internal network which I want to send udp packets. I can connect using telnet to it prooving that TCP and port forward works but when I try to send a UDP packet externally it fails.I can however send the same packet internally and port forwarding works fine.My router is Linksys by Cisco WAG320n.
View 2 Replies
View Related
Mar 4, 2011
I'm trying to open some ports for my webserver, I've configured the static IP and forwarded port 80 to my server's IP and I checked the port on canyouseeme.org and it says it's closed. I've tried multiple ports (21, 22, 7878 whatever) and all do the same thing.
So my next step was to try DMZ on the server's IP .. still no happiness .. ports stay closed. I checked this on multiple computers and it still won't open any ports for any machines on my network.
Updated to the latest firmware .. didn't make a difference. My ISP doesn't block any ports (didn't have any issues on my old router.
View 1 Replies
View Related
