I'm trying to configure port forwarding for FTP but in my case it isn't as simple as i assumed ... i have an actiontec router/modem that serves as incoming internet from my provider (FIOS), which i connected to my own router (dir-825). i mainly configure my network on the dlink and leave the actiontec alone.
[CODE]...
I have tried everything possible with this modem and router. I cant figure it out. I tried the router in bridge mode, tried opening the ports up on both of them.
View 14 Replies View RelatedI have at&t DSL with Westell Modem/Router in Bridge Mode and Linksys Router connected. The internet is working fine, but I'm unable to forward ports on the Linksys Router. The ports are 80 and 37777.
View 1 Replies View RelatedI am trying to allow an external website access to my http://localhost:8080. It is a trusted website.
I have a ZyXel Q1000 modem and a Trendnet TEW-452BRP router. The TRENDnet is serving a PS3, Xbox, Wii, and 2 iMacs and the ZyXel is serving the TRENDnet.
My public IP for the ZyXel is 65.xxx.xx.152 and it's IP address is 192.168.0.1 with a range of 192.168.0.2-254 My TRENDnet IP is 192.168.1.1 and a range of 192.168.1.100-199
I have setup a Virtual Server on the TRENDnet using HTTP, Protocol TCP 80/80 and LAN Server 198.168.1.109 (my iMac localhost). I have also setup Application forwarding and Port forwarding on both the modem and router (at different times, trying to resolve this).
Naturally none of those worked. I don't know if I need a Port forwarded or Application forwarding or the Virtual Server. Also don't know if either of those need to be on one or both devices.
All I do know is to access my localhost from the Internet, all I need to do is put http://65.xxx.xx.152 in the address bar of a browser outside my network, and my modem/and or router should forward the request to my iMac and my localhost:8080.
But every configuration I have tried does nothing of the sort.
I have a e4200 router, And a 660 series modem, I'm trying to portforward for a game called minecraft, I cannot seem to get the ports to open, I've called Century link they told me to put my modem in to bridge mode, So I did they said my IP should be public not private now, It is still private
View 6 Replies View RelatedI'm currently using Cisco EPC 3000 cable modem and Airlive wt-2400r router. Afaik the cisco isn't a router, but i'm still having some weird problems with forwarding and apparently even DMZ wont work .
View 10 Replies View Relatedport forwarding this im trying to setup a minecraft server with bukkit and i tried a number of things to port forward and it won't open port. I have a tomato firmware linksys router and a qwest modem.
View 1 Replies View RelatedI've been trying to port forward my modem and router for Xbox 360 live. Only problem is, I know absolutely nothing about networking or configuring modem / router settings.Anyhow, I was told to put my modem into Bridged Ethernet mode. I tried, then I couldn't even connect to the internet anymore.my router model is a Belkin F5D7234-4 V5. My modem is a Motorola 2210-02-1006.
View 14 Replies View RelatedNone of the port forwarding settings are working at all on my router. I have just a couple very simple settings. One of them is just an IP camera. I input the name, the TCP port, the computer (IP address) and that's it. This works just fine with my other Netgear router, but with this router, NADA. The router has the latest version of the firmware applied. Just applied it. Hardware version B. Firmware version: 2.10NA. If so, then I really need my money back since it is a main function of a router and it should work. Can't return it now, since I bought it several months ago. Never knew port forwarding didn't work because I never needed it until now.
View 6 Replies View RelatedI have DIR-615, connected via ethernet. I enabled port forwarding for Quake 3, using the range of 27660-27980 to account for custom server ports. Set schedule to "always" although also did "never" but it didn't make a difference. I checked the FAQs for frequent resets vis a vis application outbound requests, which recommended disable uPnP and this had no effect. Symptom: when Quake 3 attempts to connect to the Master Server, the router resets all connections, LAN and WLAN. It takes approximately 30 seconds to regain connection to WAN, although LAN does not drop. Also during this time, the world sigil on the router itself turns orange. This is the only time this happens, when trying to play Quake 3. Previous router to this one was Linksys (by Cisco) BEFSR41, in which simply setting up port forwarding for the client IP address allowed connection. I can find no particular reason why the router resets all interfaces when blocking a port, if it is indeed the firewall triggering this.
Other infos:
Model: Wireless N 615, DHCP enabled on both sides
LAN connect: Category5 to 10/100 NIC onboard to Intel 865GBF
Client firewall: none
Client OS: Windows XP Professional SP3
I currently use a D-Link DIR-655 router on a game server I run and I've been having this problem for sometime now. I have the router hooked up to the internet modem, and then my server computer hooked up to the router's first port. I use port forwarding to forward the game ports, as well as my FTP server ports. I have about 80 clients or so logged in at a time on my server.The issue is the following. Our internet connection has an external IP of 67.23.155.123 (this is just an example). My internal IP is 192.168.0.101.When I do "netstat" to see all the clients logged in to the game server on this computer or when I run Wireshark, every client logged in to the server (for this game application) is shown as having an IP of 67.23.155.123 (the server's external IP).On the other hand, for our FileZilla FTP server, if I run Wireshark/netstat, I can actually see the client's external IP (i.e. each individual IP of people logged into the FTP).If I hook up the server directly to the internet modem, this isn't a problem, and I am able to correctly see the IP of each client logged in to the game server individually.
View 12 Replies View RelatedJust had Verizon FIOS service installed. It comes with an actiontec modem. I would like to remove the actiontec modem and connect directly to my Linksys RT31P2 which is cascaded to my Linksys WRT54G. I have tried just about every router setup config; all with no success. How to be able to connect the FIOS directly to a linksys router.
View 3 Replies View RelatedRegion : Austria
Model : TL-MR3420
Hardware Version : V2
Firmware Version : TL-MR3420_V2_121206
ISP : 3
I am using a MR3420 V2 together with a E398 modem. The connection works well, but I can't do any port forwarding (virtual server). Using another router (Tiny Dovado) with the same E398 modem works flawlessly to forward ports.
I have the DCS-930L camera. I need to know how to setup port forwarding/triggering on my router, which is a Cisco DDR2200 CL. I understand that in order to use the camera, i need to do this. how to set up NAT.
View 1 Replies View RelatedRegion : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP : Virgin Media
Is there any way of forwarding an external port to a different internal port on the TD-8970 ?I saw a question posed on an Australian forum implying that it might be provided in a later firmware release.Our TD- 8970 has replaced a previous NetGear WAG 320N which had this facility, and is useful to provide access to multiple machines without having to modify each individually to use a different port.
I am having an issue opening a port (4040) on the 655 for my Fedora-based subsonic server. Inside the LAN, I can see the device from other peer machines, so I am confident the port is open and listening. However, I can't seem to get to the machine-port from outside/internet.
I have tried Virtual Server and Port Forwarding with single port. The server has a stactic IP which I've included in the DHCP range and outside the range. I have a DSL connection (AT&T), modem only. I have updated firmware. I have exhausted the Subsonic community's knowledge, everything points to the router, but all the settings seem correct. What am I missing? Is if possible there is a defect in the router? (don't laugh). Is there a way to trace a request to that port to see where it is hanging?
(yes, I've STFA, but don't know what else to do).
I have a Netgear WRG614 and a Westell 610015 Modem. I need Port Forwarding. I have tried setting up a static IP then Port Forwarding but it doesn't work. I have tried port forwarding from the modem but it doesn't work. I wanna forward ports "80, 9958, and 5816". The reason is because I am gonna host a game server on my computer.
View 14 Replies View RelatedI vave a zyxel p-660HW-T1 v2.I need to do PORT FORWARDING since I want to use an IP Camera in order to have remote access to video.I do not find PORT FORWARDING in the modem configuration. I find NAT, but not port forwarding.
View 1 Replies View RelatedI have TL-WR740N router. ISP should provide me up to 100Mb/s internet speed. Actual measurements shows me about 80 Mb/s. The problem is when I enable 3389 port in Port Triggering my internet speed drops to 2,5 Mb/s. When I disable port triggering, speed become normal again.
View 3 Replies View RelatedI am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedCan i connect my 3g USB modem to my dlink router directly through the usb port.
View 10 Replies View RelatedCan't connect DAP-1522 to my Verizon Fios Router
Went through the setup on the DAP-1522. Selected my Verizon FIOS wireless network and entered the WEP key. Everything looks ok on the status page - except Status: Disconnected
Reset/restarted and reconfigured DAP-1522 several times - same result. Can't get it to connect.
How I do it? I know nothing about this stuff... I can't open the ports.
View 1 Replies View RelatedI was trying to port forward and could not get it to work. I run a Camfrog room sever of my desktop computer. I needed the TCP port 6005 open to the desktop and UDP ports 5000-15000. I enter that in to the Port forwarding setting but it never work. So later on today I try this I blank out the TCP 6005 in the port forwarding and letf the UDP setting in it and saved it. Then I went to the Virtual server settings and add camfrog3 in the name and put the TCP port 6005 in to it and check it and save the setting and bingo it work.
View 1 Replies View RelatedAlright, so I'm trying to set up a Minecraft server without having to use some sort of hosting program, such as LogMeIn Hamachi. I have tried port forwarding both my external IP from "whatismyip.com" and from ipconfig in the CMD WITH the correct Minecraft port, and others still cannot connect. note that I can only connect to my own server when I use the IPv4 address from my CMD. get my server working so that others can connect? (I have been sure to change my "server properties" file's "server-ip" line accordingly.)
View 1 Replies View RelatedI setup port forwarding for many router before, but I couldn't get this one to work.I triple check all of my configuration, they all setup correctly. But the port/ports on the router is not open.
View 1 Replies View RelatedI have read the sticky about the Game fuel, and i have tried resetting everything, static IP address, all the info i have found on line. i still i keep getting booted when i join a game, or most of the time i cannot join a party. No matter what changes I make it gets worse than factory setting. i have read for hours on different ways to set up the router and what not. i have changed settings on the PS3, router and still getting nowhere.so can some one pls tell me how to set this thing up before i use it as anger management.?i know how to access the router page . but i don't get the setting up port forwarding.
View 10 Replies View RelatedFor some reason, whenever I go home (I'm in college right now), my internet goes haywire. It'll connect for about an hour or so when I first load it up, but after that, it refuses to connect at all. If I restart my modem (verizon fios modem), then it'll connect for about 5 minutesIf I run the troubleshooter, sometimes it doesn't detect anything wrong with it, and other times, it says "the default gateway is not available"[CODE]
View 1 Replies View RelatedSo I have two xbox 360's plugged directly into my dir-655 router with Ethernet cables. I have no idea how to port forward these, correctly and everything I try ends up with my router being reset. I don't have a pc connected to the router, only a wireless laptop.
opening ports for multiple xbox 360's (Black Ops is what we are trying to play).
One thing I do know is that when I tried portforward.com's walk-thru for port forwarding, when I enter the ports into the dir-655 port-forward menu, I can no longer connect to Black Ops at all, it says servers are down (WHICH THEY ARE NOT I CHECKED).
I am using DIR-655 A4 router and I have a server that needs DMZ and a PC that needs a port.So, I have set the dmz to 192.168.0.100 (SERVER) and set the port 2000(or any) to forward to 192.168.0.2 (PC).What I found out was, the port forwarding works well for several hours and suddenly it fails and won't forward until I reboot my 655 router. I am really tired doing this every day. I tried firmware 1.21 to 1.35 and non of them were good.I know that 655 has good performance compare to its price but I think it has world's worst firmware.
View 9 Replies View RelatedOne of the persons involved in a home network has installed a Dlink DIR-825 Rev-B Extreme router on the Comcast cable system to allow a 'better' wireless signal on upper floors of the home. Two others involved in the same home network use a 'secure desktop access' software called NetOp to access the network remotely. To facilitate this software, we must 'port forward' port 6502 on BOTH UDP and TCP to the single system that is accessed.
However, this setup (simple port forwarding) does not seem to work - neither does 'virtual server', for that matter. Prior to this router being installed, it was extremely simple to accomplish this remote access using a Linksys router, so our software firewall configuration has not changed but the new Dlink seems unable to allow remote access.
How (and via which of these access methods - port forwarding or virtual server) would be best? This configuration seems frustratingly difficult to accomplish and I'm about to take the Dlink 'out' of the network and re-install the Linksys with a 'high-gain' external antenna to facilitate simple signal enhancement.
Edit I've found a work-around. It's on page 2: [URL]
I'm having this really weird issue with my DIR-655 revB. I have some port forwarding rules set up and externally they work fine. However, if I try connecting to my IP address using those same ports from a computer within my LAN, it won't connect.
Externally, I can ping my WAN address and connect through forwarded ports. No problems. Internally, pinging my WAN address apparently works (just now is the first time that's worked for me), however I can't access any of my computers using the WAN IP and port forwarded ports. I can access them by going directly to their hostnames or LAN IPs.
Things I've tried:
-Disabling/enabling firewalls on all computers involved
-Disabling/enabling QoS engine
-Disabling/enabling DNS relay
-Disabling/enabling Advanced DNS
-Adding custom nameservers from Google and Comodo
-Restarting computers
-Clearing DNS cache (I use a dynamic DNS name which works externally but not internally. This gets the correct IP internally and connecting directly to the IP doesn't work either.)
-Modifying the NAT Endpoint Filtering settings
I have an external DSL modem connected to the router using PPPoE if it matters.
The weird part is that it works externally but I've modified all of the values I can think of in the config with no luck. I upgraded to the DIR-655 from a DIR-615 which had all these settings in it and worked fine (until it started acting up which is why I replaced it).
I recently upgraded my internet service and received a D-Link DIR-815 from the company as they couldn't get our older router working with the new service (4G)
My brother plays Star craft and you have to forward ports to be able to host games for others to join, but it doesn't work.
I know how to port forward because our old router had exactly the same setup, but I have one issue though, when I look at the DIR-815's manual, and even in posts made by D-Link, I've seen them asking if the filters for the firewall are set to Endpoint Independent for UDP/TCP, now I know where this is, it's under Advanced/Firewall Settings, it even shows it there in the manual, but it's not there at all under my firewall settings, my older DIR router had it and we had no problems port forwarding, I'm not sure if it was removed in a later hardware or something?
