I have setup port forwarding on the RV220W, to allow outside connections on RDP. I have tested that LAN RDP works fine, but when I test using an outside address trying to connect to an inside windows PC with RDP nothing happens.
View 11 Replies
I'm having yet another issue with my RV220w. I thought this would be a wise buy, but I keep finding reasons to hate myself for buying this router.Anyway, I need to forward port 3389, Windows Remote Desktop Protocol to one of my internal servers. I have defualt NAT, defualt firewall, etc. etc. I have seen documentation that says that Firewall -> Port Forwarding is non-functional, so I attempt to set up port forwarding via Firewall -> Access Rules. I did not see "RDP" or any other obvious acronym for Remote Desktop Protocol in the services list. So, I made a custom service, called RemoteDP, TCP protocol, port 3389 to 3389.No, I cannot RDP to my server from WAN. This was easily achieved with a cheap NETGEAR router from 2005.
View 2 Replies View RelatedHow can one forward a range of ports?
Suppose I have defined the following service:
Service: TEST
Port type: UDP
Starting port: 5060
Ending port: 5070
and I want to forward it to a specific IP. Then, if I create a new port forwarding rule for this service it asks me to specify a single port number to be used internally as:
Action: Always Allow
Service: TEST
Source IP: Any
Destination IP: 10.0.0.100
Internal Port: ?
I want to forward all ports from 5060 to 5070 to the internal range 5060 to 5070.
I made a custom port forward using tcp ports 2121-2130 to a private IP address on my network (192.168.1.8). Whenever I do this, RV220W CPU usage spikes to 98-99% and my Internet connection starts lagging a lot. Just disabling the port forward from the administation console fixes this. I'm running the latest firmware.
View 1 Replies View Relatedi have a Problem with my Cisco RV220W with the Firmware 1.0.3.5.I have in my LAN a Dreambox with the IP Adress 192.168.1.230, he listen to the Port 8880.How can I set up a port forwarding from the WAN to the Dreambox ?
View 2 Replies View RelatedI have a RV220W with 1.0.3.5 Firmware installed.
I also have a few servers with services I need to expose to outside the network (RDP and some websites) where the external port is not the same as the LAN port. I could accomplish this with my previous router using port forwarding and it looks like I can do the same here on the RV220W but I can't quite get it to work successfully.
I have read every post here about port forwarding on the RV220W and none are clear. Here is my scenario.
I have 5 static IP Addresses. I want to use one of the IP addresses to setup remote access using Remote Desktop Connection from outside the office using port address translation. for example i would like to use RDC and a specific port such as 7000 and connect to an internal PC on port 3389. sounds simple. i do this all the time on Cisco ASA's, Netgear, D-link, etc. but for the life of me cannot do it on this cisco firewall. so the port address should look like 25.25.25.25:7000 and connect to 192.168.1.25:3389. i have tried everything based on the posts without luck.
I have a setup with 2 RV220W at 2 locations.Both with the latest Firmware (1.0.3.5). I configured portforwarding for RDP at one site. Works perfekt. I also configured an IPSec VPN between the 2 sites. Works too.
Configuration overview:
Site_1:
- IPSec VPN to site_2
Site_2:
- IPSec VPN to site_1
- Port forwarding for RDP to a local server (server_2)
My first problem is that i can ping server_2 through the VPN from a pc within site_1 but i can not access this server via RDP. As soon as i disable the Portforwarding for RDP at site_2, RDP via VPN works! I assume, that the RV220W mixes up portforwarding and VPN.I tried to set up an additional firewall rule at site_2 allowing the traffic between the local networks of both sites without restrictions and place this rule at toe top. But here is my second problem: I can not add any destination network to the firewall settings (firewall-->access rules). I only allows me to define a host to redirect the traffic to.
I have recently separated a few sites that I operate, into multiple virtual machines, all with their own IP.Basically, site A is located on for instance www.siteA.com, Site B is located on blog.domain.com etc etc. So my question is, how do I (with the Cisco RV220W), forward port 80 based on host?[URL]
View 3 Replies View RelatedI'm trying to find a router that can do port forwarding to other subnets. My current linksys has IP of 192.168.1.1, and only allows me to port forward to 192.168.1.x, but I need to forward to 2.x, 3.x, 4.x
I can see how to do this on the RV215W through the online emulator, but Cisco suggested I use the RV220W. Looking through the device emulator, I can't seem to figure out how I would set it up.
Is it possible to configure the RV220W to forward ports without connecting to the SSL VPN?
View 9 Replies View RelatedI have an RV220w in office, which I have configure it for ipsec vpn connections. Behind router there is a NAS for file storage. [code]I have managed to connect to router from my home with ShrewVPN and I can ping every client connected to RV220w.The problem is that I can't connect to neither to router's web interface nor to NAS web interface or any other intranet web page ( the browser doesn't give any error, but keeps loading without showing the web page). Although, I can access web pages from my laptop.Also, in windows file explorer when I connect to NAS, although I can browse folders I can't copy files from my laptop to NAS and vice versa, I always get timeout error (I have checked the permissions to NAS and in addition I succeed to copy a small txt file 1kb, but no luck with bigger files).I also tried with QuickVPN client, but I had the same results. When I connect with pptp from windows everything works like a charm.My laptop has windows 7 64bit.
View 2 Replies View RelatedWe assign (reserve by MAC actually) static IPs to all of our devices. Over time we have gotten rid of some devices but haven't begun (or finished really) re-using the old IPs. On our WRVS4400N v2 routers we are able to set the max number of DHCP users per Vlan. This prevents unauthorized devices trying to connect to our LAN.For example. I set the range from 192.168.1.100 - 192.168.1.103. IPs 100, 101, and 103 are in use (reserved via MAC address). We set max number of DHCP users to 3. This prevents someone from gaining access to 192.168.1.102. Does this make sense? Or at least this was the initial goal and it tested out successfully back when we implemented it.
How can I do the same for with the RV220W? I can set the range, assign static IPs (reserve IPs by MAC address), but can't keep others from gaining accessing to our LAN via the unused IPs (not assigned a static IP).My initial thought was to create static IPs (for the unused IPs) using dummy MAC addresses. I'm sure there is a much better way of accomplishing what I am trying to do.
1. a LAN with about 10 pcs, a router and a shared internet connection which is connected to the router.
2. One of the PCs is a server, and is accessed from outside. the port 2230 is forwarded to it in the router.
Now the matter is, as the server uses a shared internet connection which is always very slow,I decided to have a dedicated internet connection in the server by adding an extra NIC.but what happens is when the outsiders try to connect to the dedicated internet connection IP address,the port 2230 is not forwared to the server pc.If I dissable LAN in this PC then the outsiders are able to connect.
I am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies View RelatedI'm finally jumping in over Christmas break to set up a Y network with three routers. I run a side business repairing and cleaning viruses/malware from PCs and would like the business subnet not to be able to mix with (and possibly infect) the "home" subnet.Before I knew what I was doing, I set up a simple two router "chained" network by hanging an old SMC router off my main Airport Extreme router, but I've since learned that's not ideal, since the "work" network machines can see everything on the "home" network. So, here's what I want to do. I want to put the new third router right after my cable modem (ISP). I want to keep my Airport Extreme and all devices attaching to it (home subnet) off one LAN port of this new router and my old SMC router off another LAN port of the new router (the test subnet). Currently, the IPs are: [code]My concern in setting up a "Y" configuration is that I have some wireless IP webcams on the Airport Extreme that are using port forwarding (both UDP and HTTP) so I can view them from wherever I am on the Internet, not just from within my home network.
What's the best way to make sure the port forwarding from devices on the Airport Extreme subnet works through the "new" router and out through to the Internet? Do I have to open the same ports on the new router? If so, does anyone have an example using the addresses above? Should I just put the Airport Extreme in the DMZ of the new router (so everything is just passed through - or will that allow my test subnet to see the home subnet? Some other way?
My ISP provides IPv6 connectivity in the form of dual stack IPv4/IPv6 with DHCPv6 Prefix Delegation. Using a Cisco IOS-based router I managed to make such a connection by using as a template the Cisco IOS configuration file that my ISP has posted as an example in the following link:
[URL]
The main point on this configuration is a PPPoE connection with:
interface Dialer46
ipv6 address autoconfig default
ipv6 enable
[Code].....
configure this router according the Cisco IOS configuration file I linked on the top in order to have a working IPv6 connection?
I just purchased and installed a RV220W router. I bought it specifically for the VPN capability. After successfully setting up the QuickVPN and connecting, I am confused about how to setup the router (if possible) so I can run applications remotely. Is this possible with the RV220W and if so, is there documentation to guide me in the right direction?
View 5 Replies View Relatedhow to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
I am trying to setup port forwarding on the asa. Inbound port 3062 needs to go to an address on a server inside the corporation. NO DMZ...I do not have the option under firewall to select port forwarding. I have add a nat rule before network object , add network object add nat rule after network object i am not sure who is inbound (I will ask) all customer said was certain ports need to go to certain PC's and the asiest way is to add portforwarding but I dont see the "Add " under firewall as so many posts say..
View 1 Replies View RelatedI have Cisco 2910 router that have 3 interfaces:
g0/0 - LAN
g0/1 - WAN1
g0/2 - WAN2
I would like to configure port forwarding in such way that connections to both WAN interface on identical ports will be redirected to a single host in a private network. When I issue command: ip nat inside source static tcp 10.10.10.X 8080 interface g0/1 8080 everything is fine, until I add the second command: ip nat inside source static tcp 10.10.10.X 8080 interface g0/2 8080
After that, the first statement is just replaced by the second one, not added to configuration.
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies View RelatedI just bought a RV220W. One of the features I need to setup is a daily wireless plan, i.e. parental control: my wireless connection needs to be open at different times depending on the day, for 2 specific wireless devices, while others wireless devices have continuous access. Unfortunately, the wireless schedule only lets me set up one start/stop time only (i.e. the same one every day).
I noticed that I could possibly set up a firewall access rule with a specific schedule, but I have no idea if this would work, and how to set it up. My basic idea was then to open the wireless SSID I want to control from 7.30am to 11pm every day, and then add a firewall rule that would close the access to the said devices (using their MAC address) from say 10-11pm on given days... But I am not quite sure how to set this up.
I have a RV220W setup with SSL VPN users, authenticating to an internal Active Directory. Maybe 5 ports forwarded and 8 external IP addresses. Besides this i have 1 data VLAN and a voice vlan on my network.
The reboots are on different times on a day, even on Sundays at 7 AM when noone is logged in to the network.FW is at 1.0.4.17.
I have a small network in my garage, it's basically made up of a bunch of test servers. Those and a win xp machine are all hooked up to a switch, and the win xp machine also has a wireless usb stick that is connected to my wireless router, and is being used to share internet to the rest of the machines. The test servers along with the NIC card on my win xp machine sit on a different subnet, however.When I remote into the win xp machine from my house, i can run a second remote desktop in the first session, into any of my servers. I want to do work on them, but its very laggy.
Is there a way I can setup a port either on the win xp machine or my wireless router so that i can remote directly into one of the servers? so if the win xp machine has a wireless ip address of 192.16.13.102, and one of the servers on the 2nd subnet has an internal ip of 192.2.2.4, can i have it so i can make, for instance, 192.16.13.102:6333 forward to 192.2.2.4? If not, is there any other way i can directly remote into one of the servers, by passing the first remote desktop into win xp? What settings would have to be the same across the line?
I need to setup some port forwarding on my X3000 to pass through the firewall to my server but cannot find the relevant page in the setup GUI.
View 2 Replies View RelatedI have a Cisco RV220W updated to latest firmware 1.0.4.17. I have been trying to get a VPN setup for the past few days without success. We had a test VPN up and running previously, but when we changed the IP's and secret key to connect the live VPN tunnel it failed and we haven't been able to get it working since.We have deleted both ends, rebuilt them probably 6 times each. We have changed secret keys, tried 3DES, AES, and AES256 encryptions with SHA-1. All the internal IP settings are correct :IE 192.168.1.1/24 or 192.168.1.1 255.255.255.0,External IP's are right, only oddball thing here is one of the external IP's is assigned by DHCP and is a /22 although the previous tunnel worked with the same ISP.
View 1 Replies View RelatedI'm trying to set up my WRT54G wireless router so.i can port forward the relevant ports for my programs. I understand that you have to set up a static ip address before you can do a port forward which makes sense as you do not want to keep changing the ip address for the forwarding settings every time your network refreshes. But I cant seem to have it set up. And is there a rule that the static ip that you set should not be within the dhcp range?After setting up the static ip and setting up the port forward settings how do I test if the port is being forwarded correctly?
View 1 Replies View RelatedI have the DCS-930L camera. I need to know how to setup port forwarding/triggering on my router, which is a Cisco DDR2200 CL. I understand that in order to use the camera, i need to do this. how to set up NAT.
View 1 Replies View RelatedI just setup my homelab today, after having Cat5e installed so I can run my servers and network equiptment over wired network as well as setting up a wireless system. I got everything setup and its going great I can access everything from my office now including a E4200 Linksys router that I setup to do RiP (was only choice pretty much, or NAT), and my 891 Cisco Router which is my internet connection.
I use to have the linksys setup to do port forwarding but now I need to figure out how to do it on the cisco 891 router via command line.
Below is my current configuration. I need to be able to access my server which is behind my router by Remote Desktop. I also have a web server, and the kids also play minecraft, and have a server setup so I need to be able to forward their port as well.
[URL]
Ths is from the link above, would I just do like that but then put in my IPs and is that my Private IP I use this or my public facing. Also he has "interface Dialer1 6881" again after the port in the second and third row. I dont really understand what they have there. I understand basic access list and such though I am extremely rusty.
!
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.0.0.2 6881 interface Dialer1 6881
[Code].....
i'm using an rv220W and i whant to know if is it possible to assign vpn traffic to a vlan when i setup an ipsec tunnel?
example:
Im using different vlans on my rv220W.
Vlan 10: engineers (ex: 192.168.1.0/27) no intervlan routing
Vlan20: sales (ex: 10.0.123.0/24) no intervlan routing
This is what i need: - An engineer is on the road and when he makes a ipsec vpn connection => assignd to the vlan "engineers" so he can access the server/pc's in that vlan.and when someone from the sales group starts a vpn connection he needs to be in the vlan "sales" so he can access his pc/data,...
I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
