I have recently separated a few sites that I operate, into multiple virtual machines, all with their own IP.Basically, site A is located on for instance www.siteA.com, Site B is located on blog.domain.com etc etc. So my question is, how do I (with the Cisco RV220W), forward port 80 based on host?[URL]
View 3 Replieshow to: port forwarding to 2 different destinations based on incoming WAN port
The default HTTP service works fine: TCP80/80-> 192.168.0.55
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
I was able to do port redirect with the Symantec Firewall I'm replacing.
I'm having yet another issue with my RV220w. I thought this would be a wise buy, but I keep finding reasons to hate myself for buying this router.Anyway, I need to forward port 3389, Windows Remote Desktop Protocol to one of my internal servers. I have defualt NAT, defualt firewall, etc. etc. I have seen documentation that says that Firewall -> Port Forwarding is non-functional, so I attempt to set up port forwarding via Firewall -> Access Rules. I did not see "RDP" or any other obvious acronym for Remote Desktop Protocol in the services list. So, I made a custom service, called RemoteDP, TCP protocol, port 3389 to 3389.No, I cannot RDP to my server from WAN. This was easily achieved with a cheap NETGEAR router from 2005.
View 2 Replies View RelatedHow can one forward a range of ports?
Suppose I have defined the following service:
Service: TEST
Port type: UDP
Starting port: 5060
Ending port: 5070
and I want to forward it to a specific IP. Then, if I create a new port forwarding rule for this service it asks me to specify a single port number to be used internally as:
Action: Always Allow
Service: TEST
Source IP: Any
Destination IP: 10.0.0.100
Internal Port: ?
I want to forward all ports from 5060 to 5070 to the internal range 5060 to 5070.
I made a custom port forward using tcp ports 2121-2130 to a private IP address on my network (192.168.1.8). Whenever I do this, RV220W CPU usage spikes to 98-99% and my Internet connection starts lagging a lot. Just disabling the port forward from the administation console fixes this. I'm running the latest firmware.
View 1 Replies View Relatedi have a Problem with my Cisco RV220W with the Firmware 1.0.3.5.I have in my LAN a Dreambox with the IP Adress 192.168.1.230, he listen to the Port 8880.How can I set up a port forwarding from the WAN to the Dreambox ?
View 2 Replies View RelatedI have a RV220W with 1.0.3.5 Firmware installed.
I also have a few servers with services I need to expose to outside the network (RDP and some websites) where the external port is not the same as the LAN port. I could accomplish this with my previous router using port forwarding and it looks like I can do the same here on the RV220W but I can't quite get it to work successfully.
I have read every post here about port forwarding on the RV220W and none are clear. Here is my scenario.
I have 5 static IP Addresses. I want to use one of the IP addresses to setup remote access using Remote Desktop Connection from outside the office using port address translation. for example i would like to use RDC and a specific port such as 7000 and connect to an internal PC on port 3389. sounds simple. i do this all the time on Cisco ASA's, Netgear, D-link, etc. but for the life of me cannot do it on this cisco firewall. so the port address should look like 25.25.25.25:7000 and connect to 192.168.1.25:3389. i have tried everything based on the posts without luck.
I have a setup with 2 RV220W at 2 locations.Both with the latest Firmware (1.0.3.5). I configured portforwarding for RDP at one site. Works perfekt. I also configured an IPSec VPN between the 2 sites. Works too.
Configuration overview:
Site_1:
- IPSec VPN to site_2
Site_2:
- IPSec VPN to site_1
- Port forwarding for RDP to a local server (server_2)
My first problem is that i can ping server_2 through the VPN from a pc within site_1 but i can not access this server via RDP. As soon as i disable the Portforwarding for RDP at site_2, RDP via VPN works! I assume, that the RV220W mixes up portforwarding and VPN.I tried to set up an additional firewall rule at site_2 allowing the traffic between the local networks of both sites without restrictions and place this rule at toe top. But here is my second problem: I can not add any destination network to the firewall settings (firewall-->access rules). I only allows me to define a host to redirect the traffic to.
I have setup port forwarding on the RV220W, to allow outside connections on RDP. I have tested that LAN RDP works fine, but when I test using an outside address trying to connect to an inside windows PC with RDP nothing happens.
View 11 Replies View RelatedI'm trying to find a router that can do port forwarding to other subnets. My current linksys has IP of 192.168.1.1, and only allows me to port forward to 192.168.1.x, but I need to forward to 2.x, 3.x, 4.x
I can see how to do this on the RV215W through the online emulator, but Cisco suggested I use the RV220W. Looking through the device emulator, I can't seem to figure out how I would set it up.
Is it possible to configure the RV220W to forward ports without connecting to the SSL VPN?
View 9 Replies View RelatedI have created a connection gateway-to-gateway between RV220W and RVL200, is doing without any problems.For example, I can ping the gateway on the other side. But when I connect trough RV220W QuickVPN (or PPTP) I can not reach the gateway (RVL200) or any host behind it.
View 4 Replies View RelatedMy ISP waits a definite host name from me to return my white IP address via DHCP. Can I set this parameter in RV220W router? I don't find such parameter in IPv4 WAN configuration page.
View 1 Replies View RelatedOne of the persons involved in a home network has installed a Dlink DIR-825 Rev-B Extreme router on the Comcast cable system to allow a 'better' wireless signal on upper floors of the home. Two others involved in the same home network use a 'secure desktop access' software called NetOp to access the network remotely. To facilitate this software, we must 'port forward' port 6502 on BOTH UDP and TCP to the single system that is accessed.
However, this setup (simple port forwarding) does not seem to work - neither does 'virtual server', for that matter. Prior to this router being installed, it was extremely simple to accomplish this remote access using a Linksys router, so our software firewall configuration has not changed but the new Dlink seems unable to allow remote access.
How (and via which of these access methods - port forwarding or virtual server) would be best? This configuration seems frustratingly difficult to accomplish and I'm about to take the Dlink 'out' of the network and re-install the Linksys with a 'high-gain' external antenna to facilitate simple signal enhancement.
I recently upgraded my internet service and received a D-Link DIR-815 from the company as they couldn't get our older router working with the new service (4G)
My brother plays Star craft and you have to forward ports to be able to host games for others to join, but it doesn't work.
I know how to port forward because our old router had exactly the same setup, but I have one issue though, when I look at the DIR-815's manual, and even in posts made by D-Link, I've seen them asking if the filters for the firewall are set to Endpoint Independent for UDP/TCP, now I know where this is, it's under Advanced/Firewall Settings, it even shows it there in the manual, but it's not there at all under my firewall settings, my older DIR router had it and we had no problems port forwarding, I'm not sure if it was removed in a later hardware or something?
Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80
I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.
View 6 Replies View RelatedI have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042 router and was succesful ( by typing 192.168.1.1 in the explorer and logged in using user name and password )
I am using a linux embedded system whose Internal IP ,Internal port are mapped .This system is connected to one of the LAN ports
I want to try auto UPnP port forwarding both for RV042 router and Linksys E4200 routers
After enabling the Upnp option only and logging out ,Can i add a port mapping entry in this router without logging in using a C++ program which runs on linux embedded system .
recently got a RV220W and liking all the configuration options.
Although I cannot find where to change the listening port for management? I want it to listen on port 81 instead of 80.
I have a customer with a Sonic wall that I want to replace with a 521.He currently has port forwaring setup so that only 3 ip addresses can access the port forward. Everyone else is dropped. Is there a way to do something similar?I can make it work for a single one via the DMZ tab with a source ip address. but there is not a way I can find to add the allow for the other two remote connections.
View 1 Replies View RelatedI am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedFrom an older manual it describes how to configure this. I installed the oldest firmware available for download and this feature is there. Was this just simply moved somewhere else in the newer firmware?
Configuring Port VLANs
You can associate VLANS on the Cisco RV220W to the LAN ports on the device.
By default, all 4 ports belong to VLAN1. You can edit these ports to associate them
[Code].....
I have a Cisco RVS4000 with Port 1 as a trunk connection to a Cisco SF300 switch. Port 1 on the router is configured 1untag,2tag,3tag,4ag. When connected directly to the router I can connect to the switches management IP. I would like to reach the switch remotely. I have set up DDNS and can access the router and I have have set a specific port to forward to port 80 on the switches management IP but this does not work. Should I not be able to Port Forward to the switch across VLAN 1?
View 3 Replies View RelatedPort forwarding on rv120 does not work. I have followed the workaround instructions: so i have created a firewall access rule on incoming port 21 to an internal ip address on the same port. The router has created the forwarding port rule. But port forwarding does not work. I have tried to use a custom service but nothing!
The router is reachable from wan, I can access via DNS the configuration page and I can ping the router on wan port.
Currently I have the RV042 router working in a dual WAN set up, it is configured to accept connections on numbers of ports like 80,443, 25 and forward them to a local ip.
The problem is this only works with WAN1. Is it even possible to forward ports for connections coming in over WAN2?
I', trying to open my ports 80 and 37777 and have successfully opened them on my linksys router but behind that I have an at&t modem/router....My questions is how do I find the URL number to access my second router to open the ports on it also?
View 3 Replies View RelatedI am trying to access home security camera from outslide my house.I have an AT&T internet coming into the house. They have a router that comes into the house and that splits off to another router in my house which carriers CAT5 all over the house. One of the wires go to another router that I use for my wireless devices.One of those wireless devices is an security camera.Here is my question. I want to view the camera from the internet outside the house. I have followed the instructions given by the manufacture for port forwarding. I have port forwarded the wireless router since the camera is connected to it. Is that wrong since the DSL is coming in one router and then going to another and then to the wireless
View 2 Replies View RelatedI have set up our network with an RV220W as gateway/Wifi-AP,VPN host.I am able to connect over the WWW with the windows 7 client laptops no problem, BUT ,I cannot from my office reach out to the laptops, it seems as if the tunnel is one way.The users can do anything they need, but I want to be able to connect to them to update their AVG or render remote assistance etc.Ping from client to home network no problem.Client laptop is invisible to any ping etc FROM the home network.
View 2 Replies View RelatedI just got a new rv120w and want to set it up, like my old router. I have a webserver that people around the world, should be able to visit, but I can't figure whats wrong. You can see my settings in port forwarding here.
View 4 Replies View RelatedI have a RV042 with Port Forwarding configured for RDP. This Port Forwarding Rule is being applied before my ACL - so subnets that are not authorized through are being allowed in. Firmware version 4.0.0.07.
View 2 Replies View RelatedToday i installed an RV180 VPN router as replacement for a netscreen ns-5GT.Exactly the same configuration, everything works, except port forwarding from WAN to a host inside NAT.My ports are open (online port-scanner sees the ports as open), the hosts are accepting connections, but a connection can't be made.Probably a bug in the firmware.
View 30 Replies View RelatedWe have the following proplem with the RV 120w router with the last firmware. We can't manage to set up port forwarding. So the situation is like this: we have WAN ip: 192.168.2.68 and our router connects to VPN server and gets an IP like 10.0.10.X. In the inner network we have PCs and a DVR (digital video recorder) with ip 192.168.1.215. Our DVR uses 3 main ports like 81 (http) and 37777 (tcp), 37778 (udp) and we try to make port forwarding with the router interface like the manual says (look and the sceenshot). But when we try to enter our DVR and see the picture from the outside network (we type in browser 192.168.2.68:81) nothing happends. It just dosen't work.
Before cisco we used d-link router and everything worked just fine with the same port forwarding rules.So we need to enter WAN address in Cisco and show the 81 port in the address bar and see the picture from the DVR 192.168.1.215 from the inner network.