Cisco Routers :: RV220W Find Router That Can Do Port Forwarding To Other Subnets

Mar 31, 2013

I'm trying to find a router that can do port forwarding to other subnets. My current linksys has IP of 192.168.1.1, and only allows me to port forward to 192.168.1.x, but I need to forward to 2.x, 3.x, 4.x
 
I can see how to do this on the RV215W through the online emulator, but Cisco suggested I use the RV220W. Looking through the device emulator, I can't seem to figure out how I would set it up.

View 6 Replies


ADVERTISEMENT

Cisco Routers :: RV220w RDP Port Forwarding Non-functional

Sep 24, 2011

I'm having yet another issue with my RV220w. I thought this would be a wise buy, but I keep finding reasons to hate myself for buying this router.Anyway, I need to forward port 3389, Windows Remote Desktop Protocol to one of my internal servers.  I have defualt NAT, defualt firewall, etc. etc.  I have seen documentation that says that Firewall -> Port Forwarding is non-functional, so I attempt to set up port forwarding via Firewall -> Access Rules.  I did not see "RDP" or any other obvious acronym for Remote Desktop Protocol in the services list.  So, I made a custom service, called RemoteDP, TCP protocol, port 3389 to 3389.No, I cannot RDP to my server from WAN. This was easily achieved with a cheap NETGEAR router from 2005.

View 2 Replies View Related

Cisco Routers :: RV220W Forwarding Port Range?

Sep 4, 2012

How can one forward a range of ports?
 
Suppose I have defined the following service:
 
Service: TEST
Port type: UDP
Starting port: 5060
Ending port: 5070
 
and I want to forward it to a specific IP. Then, if I create a new port forwarding rule for this service it asks me to specify a single port number to be used internally as:
 
Action: Always Allow
Service: TEST
Source IP: Any
Destination IP: 10.0.0.100
Internal Port: ?
 
I want to forward all ports from 5060 to 5070 to the internal range 5060 to 5070.

View 4 Replies View Related

Cisco Routers :: RV220W Port Forwarding An 99% CPU Usage

Mar 10, 2012

I made a custom port forward using tcp ports 2121-2130 to a private IP address on my network (192.168.1.8). Whenever I do this, RV220W CPU usage spikes to 98-99% and my Internet connection starts lagging a lot. Just disabling the port forward from the administation console fixes this. I'm running the latest firmware.

View 1 Replies View Related

Cisco Routers :: RV220W - Set Up Port Forwarding From WAN To Dreambox?

Nov 23, 2011

i have a Problem with my Cisco RV220W with the Firmware 1.0.3.5.I have in my LAN a Dreambox with the IP Adress 192.168.1.230, he listen to the Port 8880.How can I set up a port forwarding from the WAN to the Dreambox ?

View 2 Replies View Related

Cisco Routers :: RV220W - Port Forwarding - Different Ports

Nov 26, 2011

I have a RV220W with 1.0.3.5 Firmware installed.
 
I also have a few servers with services I need to expose to outside the network (RDP and some websites) where the external port is not the same as the LAN port. I could accomplish this with my previous router using port forwarding and it looks like I can do the same here on the RV220W but I can't quite get it to work successfully.

View 3 Replies View Related

Cisco Routers :: RV220W - Firmware 1.0.3.5 Port Forwarding With Static IPs

Apr 24, 2012

I have read every post here about port forwarding on the RV220W and none are clear. Here is my scenario.
 
I have 5 static IP Addresses. I want to use one of the IP addresses to setup remote access using Remote Desktop Connection from outside the office using port address translation. for example i would like to use RDC and a specific port such as 7000 and connect to an internal PC on port 3389. sounds simple. i do this all the time on Cisco ASA's, Netgear, D-link, etc. but for the life of me cannot do it on this cisco firewall. so the port address should look like 25.25.25.25:7000 and connect to 192.168.1.25:3389. i have tried everything based on the posts without luck.

View 1 Replies View Related

Cisco Routers :: RV220W - Port Forwarding Collides With IPSec?

Feb 1, 2012

I have a setup with 2 RV220W at 2 locations.Both with the latest Firmware (1.0.3.5). I configured portforwarding for RDP at one site. Works perfekt. I also configured an IPSec VPN between the 2 sites. Works too.
 
Configuration overview:
Site_1:
- IPSec VPN to site_2
 Site_2:
- IPSec VPN to site_1
- Port forwarding for RDP to a local server (server_2)
 
My first problem is that i can ping server_2 through the VPN from a pc within site_1 but i can not access this server via RDP. As soon as i disable the Portforwarding for RDP at site_2, RDP via VPN works! I assume, that the RV220W mixes up portforwarding and VPN.I tried to set up an additional firewall rule at site_2 allowing the traffic between the local networks of both sites without restrictions and place this rule at toe top. But here is my second problem: I can not add any destination network to the firewall settings (firewall-->access rules). I only allows me to define a host to redirect the traffic to.

View 3 Replies View Related

Cisco Routers :: Host-based Port Forwarding With A RV220W?

Apr 10, 2012

I have recently separated a few sites that I operate, into multiple virtual machines, all with their own IP.Basically, site A is located on for instance www.siteA.com, Site B is located on blog.domain.com etc etc. So my question is, how do I (with the Cisco RV220W), forward port 80 based on host?[URL]

View 3 Replies View Related

Cisco Routers :: Setup Port Forwarding On RV220W To Allow Outside Connections On RDP

Sep 5, 2011

I have setup port forwarding on the RV220W, to allow outside connections on RDP. I have tested that LAN RDP works fine, but when I test using an outside address trying to connect to an inside windows PC with RDP nothing happens.

View 11 Replies View Related

Cisco WAN :: 5505 - Limiting Port 25 Forwarding To Specific IP Subnets

Jan 26, 2013

just getting started with ASA's. I've got my 5505 almost 100% configured but my port 25 forward to my Exchange server. Currently I've got an access list forwarding all traffic that hits the outside interface on port 25 to my Exchange server (access-list outside-in extended permit tcp any object mail-port-25 eq smtp). What I'd like to do now is say that only port 25 traffic from specific IP subnets gets forwarded. I thought I read that there's a couple of way to do this (from the inside interface, from the outside interface).
 
Also, what happens to port 25 hits that don't fall within the range I specify? Do they get a disconnect reply or do they just get ignored (no reply whatsoever)?
 
Edit: ...just to clarify, the allowed IP's I will be entering are the WAN IP's of my AS/AV service.     

View 6 Replies View Related

Cisco WAN :: Port Forwarding On RV220W?

Jul 14, 2011

Is it possible to configure the RV220W to forward ports without connecting to the SSL VPN?

View 9 Replies View Related

Cisco Routers :: Where To Find MIB Files For RV220W

Sep 26, 2011

Where I can find the MIB files for RV220W router?

View 2 Replies View Related

Routers / Switches :: Sky Router Port Forwarding

Feb 12, 2011

I am trying to open port 12000 on my sky dlink router, been trying for a few days now and i just can't nail it. When i log into router, it brings up the sky router page, any one ever setup port 12000 on the sky router page.

View 1 Replies View Related

Cisco Routers :: RV215W Router Port Forwarding Not Working?

May 11, 2013

RV215W router port forwarding not working.Port forwarding works for a short period of time, then stops working.  Reboot router, works again for short period of time, then stops again.
 
I have updated firmware to latest.  I had seen other similar bugs posted for 220 and I think 180, not sure if this router has similar bugs and waiting for fix release to firmware.I had recently purchased two, one deployed, will hold off on other now because of issues, and may have to move to different unit if a resolution not found this week.

View 5 Replies View Related

Cisco Routers :: Unable To Find Any Info Pertaining To PD In Relation To RV220W

Nov 5, 2011

I have an RV220W with firmware version 1.0.2.4. My ISP makes available IPv6 over PPPoE in a Dual Stack configuration. One of the requirements is that my home router should support prefix delegation. I don't appear to be able to find any information pertaining to PD in relation to the RV220W -

View 6 Replies View Related

Zyxel P-660HW-T1 Don't Find Port Forwarding In Modem Configuration

Oct 9, 2011

I vave a zyxel p-660HW-T1 v2.I need to do PORT FORWARDING since I want to use an IP Camera in order to have remote access to video.I do not find PORT FORWARDING in the modem configuration. I find NAT, but not port forwarding.

View 1 Replies View Related

Cisco Routers :: Does RV042 Router / Firewall Support Port Forwarding From Internet

Aug 5, 2011

I am using an RV042 router/firewall -- firmware v1.3.13.02-tm -- connected to a cable modem.I have one public address (WAN1) assigned by my ISP's DHCP server.All my machines on the LAN have static IPs.  (RV042 DHCP Server is disabled.)I have set up port (80) forwarding to 192.168.1.101 The HTTP port forwarding does work if an http client on the LAN sends a request to http://<public-ip>:80But I cannot get a response if I send a request to  http://<public-ip>:80 from a machine on the WAN.
 
I  did configure Access Rules to allow http traffic (and then tried to  allow *all* traffic) between a single IP on the WAN and 192.168.1.101 The  incoming log table shows a connection is made from the http client on the internet to the correct http server on the LAN, but there is no resonse  from the LAN to the remote client.Is my configuration the problem, or is this feature not supported by the RV042 router? Could my cable modem be blocking outbound traffic?

View 1 Replies View Related

Cisco Routers :: RV042G - Port Forwarding To 2 Different Destinations Based On Incoming Wan Port

Apr 22, 2013

how to: port forwarding to 2 different destinations based on incoming WAN port
 
The default HTTP service works fine: TCP80/80-> 192.168.0.55
 
I have a couple of IP security camera's I'd like to be able to access remotely that also listen on port 80. I tried TCP & UDP 8009/8009-> 192.168.0.9 without any luck. Not sure how to handle the port redirects on the RV042G? Seems simple and was on the Symantec, could be user training :-)
 
I was able to do port redirect with the Symantec Firewall I'm replacing.

View 2 Replies View Related

Cisco Routers :: RV042G Port Forwarding From Public Port To Internal IP?

Oct 11, 2012

Is it possible to create a service which will forward public port 9010 to an internal IP address with port 23 ?
 
First of all, I do not like to open the public Telnet port to the inside so I would use another public port and second my ISP does not allow some public ports beneath port 80

View 2 Replies View Related

Cisco Routers :: SRP541W Set Up Port Forwarding From External Port

Apr 13, 2013

I've set up port forwarding from an external port (9000) to an internal port (80) on our SRP541W, and for some reason, it's not working externally. If I access the public address from within the internal network, it works properly.

View 6 Replies View Related

Routers / Switches :: Huawei 523a Router Doesn't Allow IP Camera Port Forwarding?

Jan 17, 2013

I have a Huawei 523a Router at the moment and I'm trying to setup a IP camera.The Router doesnt allow port forwarding, so my question is can I add another Router onto the Huawei router to allow the second one to work my camera

View 10 Replies View Related

Home Network :: Advanced Home Network Setup (3 Subnets) And Port Forwarding?

Feb 24, 2013

I have a Time Warner Cable business class service with no static IP, with a wireless modem which is plugged to a CAT5 distribution panel. On the jacks (2 other rooms on the house) I have a Linksys E3000 and a Linksys Valet router for signal boost and gadgets usage (TV, cameras, etc).The main router (TWC) has it's own external IP which TWC assigns to me and internally distributes via DHCP the range 192.168.0.x. With that said:

- The E3000 has a 192.168.0.6 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The Valet has a 192.168.0.7 IP -- this is fixed setup on the TWC router (ubee brand) by MAC address
- The main router has the 192.168.0.1 as the gateway and web-interface

Whenever I connect something to the E3000, it is distributing the 192.168.1.x range and the valet 192.168.2.x range.That works perfectly for my home based business until I decided to use more stuff on the network such as a IP printer, IP cameras, etc.

- The IP cameras are connected to the E3000 due to signal strength and I have manually assigned them the 192.168.1.15 and 192.168.1.16 IPs and ports 9001 and 9002.

- The printer is connected to the E3000 and I have manually assigned the IP 192.168.1.30.

Issue 1: Port forwarding On the main router (TWC - UBEE) I have tried to setup a port forwarding by informing the Local IP as 192.168.0.6 (E3000 IP), Internal Port 0, Public Interface IP (0.0.0.0), Ext Start Port 9001, Ext End Port 9001, Protocol - Both, Enabled Yes. On the E3000 I did the same config (screen shot attached e3000.png).This is not working properly. I can't get into the camera.

Issue 2: Printer/ The printer is only accessible if I connect to the E3000 (because it is on the 192.168.1.x network)

Issue 3: How to configure all the devices on the same subnet? If I want everyone to be on the 192.168.0.x network, how to configure properly the E3000 and the Valet? I have tried to force them into the same network but it would not work properly. It would not get an IP from the UBEE router (main).

View 5 Replies View Related

Cisco Routers :: Auto / Programmatic UPnP Port Forwarding For RV042 And E4200 Routers

Jan 24, 2013

I have RV042 and E4200 routers . I tried the manual UPnP port forwarding using Rv042  router and was succesful ( by typing 192.168.1.1  in the explorer and  logged in using user name and password )
 
I am using a linux embedded system  whose  Internal IP ,Internal port  are mapped  .This system is connected to one of the LAN ports    
 
I want to try auto UPnP port forwarding both for  RV042 router and Linksys E4200 routers 
 
After  enabling the Upnp option only  and logging out ,Can i add a port mapping entry in this router without logging in  using  a  C++ program  which runs on  linux embedded system .

View 2 Replies View Related

Cisco Routers :: RV220W Default Listening Port For Management

Aug 13, 2011

recently got a RV220W and liking all the configuration options.
 
Although I cannot find where to change the listening port for management? I want it to listen on port 81 instead of 80.

View 5 Replies View Related

Cisco Switching/Routing :: 881W - IOS Port Forwarding Commands For Port Forwarding

Apr 7, 2013

I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.

View 1 Replies View Related

Cisco Routers :: RV220W Port VLANS - Missing Feature In Newer Firmware

Nov 11, 2012

From an older manual it describes how to configure this. I installed the oldest firmware available for download and this feature is there. Was this just simply moved somewhere else in the newer firmware?
 
Configuring Port VLANs
You can associate VLANS on the Cisco RV220W to the LAN ports on the device.
By default, all 4 ports belong to VLAN1. You can edit these ports to associate them

[Code].....

View 2 Replies View Related

Cisco Routers :: Port Forwarding Beyond RVS4000?

Feb 8, 2012

I have a Cisco RVS4000 with Port 1 as a trunk connection to a Cisco SF300 switch.  Port 1 on the router is configured 1untag,2tag,3tag,4ag. When connected directly to the router I can connect to the switches management IP.  I would like to reach the switch remotely.  I have set up DDNS and can access the router and I have have set a specific port to forward to port 80 on the switches management IP but this does not work.  Should I not be able to Port Forward to the switch across VLAN 1?

View 3 Replies View Related

Cisco Routers :: Port Forwarding On RV120

Apr 10, 2012

Port forwarding on rv120 does not work. I have followed the workaround instructions: so i have created a firewall access rule on incoming port 21 to an internal ip address on the same port. The router has created the forwarding port rule. But port forwarding does not work. I have tried to use a custom service but nothing!
 
The router is reachable from wan, I can access via DNS the configuration page and I can ping the router on wan port.

View 10 Replies View Related

Cisco Routers :: RV042 - Port Forwarding Using Both WAN 1 And 2

Apr 19, 2013

Currently I have the RV042 router working in a dual WAN set up, it is configured to accept connections on numbers of ports like 80,443, 25 and forward them to a local ip.

The problem is this only works with WAN1. Is it even possible to forward ports for connections coming in over WAN2?

View 5 Replies View Related

Dual Routers Port Forwarding?

Mar 10, 2011

I', trying to open my ports 80 and 37777 and have successfully opened them on my linksys router but behind that I have an at&t modem/router....My questions is how do I find the URL number to access my second router to open the ports on it also?

View 3 Replies View Related

Multiple Routers And Port Forwarding?

Jul 7, 2011

I am trying to access home security camera from outslide my house.I have an AT&T internet coming into the house. They have a router that comes into the house and that splits off to another router in my house which carriers CAT5 all over the house. One of the wires go to another router that I use for my wireless devices.One of those wireless devices is an security camera.Here is my question. I want to view the camera from the internet outside the house. I have followed the instructions given by the manufacture for port forwarding. I have port forwarded the wireless router since the camera is connected to it. Is that wrong since the DSL is coming in one router and then going to another and then to the wireless

View 2 Replies View Related

Cisco Routers :: Rv120w And Simple Port Forwarding?

Aug 26, 2011

I just got a new rv120w and want to set it up, like my old router. I have a webserver that people around the world, should be able to visit, but I can't figure whats wrong. You can see my settings in port forwarding here.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved