Cisco Routers :: RV220W VPN Setup For Connecting The Live Vpn Tunnel If Failed
Dec 20, 2012
I have a Cisco RV220W updated to latest firmware 1.0.4.17. I have been trying to get a VPN setup for the past few days without success. We had a test VPN up and running previously, but when we changed the IP's and secret key to connect the live VPN tunnel it failed and we haven't been able to get it working since.We have deleted both ends, rebuilt them probably 6 times each. We have changed secret keys, tried 3DES, AES, and AES256 encryptions with SHA-1. All the internal IP settings are correct :IE 192.168.1.1/24 or 192.168.1.1 255.255.255.0,External IP's are right, only oddball thing here is one of the external IP's is assigned by DHCP and is a /22 although the previous tunnel worked with the same ISP.
View 1 Replies
ADVERTISEMENT
Apr 7, 2012
i'm using an rv220W and i whant to know if is it possible to assign vpn traffic to a vlan when i setup an ipsec tunnel?
example:
Im using different vlans on my rv220W.
Vlan 10: engineers (ex: 192.168.1.0/27) no intervlan routing
Vlan20: sales (ex: 10.0.123.0/24) no intervlan routing
This is what i need: - An engineer is on the road and when he makes a ipsec vpn connection => assignd to the vlan "engineers" so he can access the server/pc's in that vlan.and when someone from the sales group starts a vpn connection he needs to be in the vlan "sales" so he can access his pc/data,...
View 15 Replies
View Related
Sep 25, 2011
I just bought an RV220w. My first act was updating th firmware to 1.0.2.4. Unfortunately I was not able to configure the router for vlan purpose 'cause the "Port VLAN" point was missing in the webinterface. I performed several factory reset but it didnt work for me - so I got back to firmware 1.0.1.0.
View 9 Replies
View Related
Mar 10, 2013
I have a RV220W running 1.0.1.0. When trying to upgrade to 1.0.4.17 I receive an error: "Upgrade failed due to invalid/corrupted firmware".
I found this article: [URL]
I assume I have to do a factory reset then an upgrade in order to upgrade properly.
If I do a backup running 1.0.1.0, then upgrade to 1.0.4.17, then do a restore, would that put me back to 1.0.1.0? I'm trying to avoid configuring the router manually all over again.
View 1 Replies
View Related
Aug 28, 2011
IPv6 -> Tunneling.The 6to4 tunnel did not initialize after a reboot. The automatic tunneling had to be disabled and enabled again.It was used for a 6in4 tunnel to tunnelbroker and the Remote End Point IPv4.Address was enabled and specified.
View 1 Replies
View Related
Sep 26, 2012
We have 2 RV220W Routers installed in seperate offices. We are attempting to setup a IPSec tunnel between the two sites. So far we have been unsuccessful in getting this to work.On both sides, we are getting a successful connection established, but netiher site is recieving any packets. Both sides are transmitting packets though. We have exhausted our resources trying to figure out why.
View 4 Replies
View Related
Apr 21, 2012
I have two offices connected with an IPSEC VPN tunnel using RV220W routers. The Tunnel works fine for local users between the two sites(Site 1:10.0.0.x; site 2 is 10.0.2.x). I have also set up PPTP users for remote access. PPTP users that connect to site 1 cannot access site 2 and vice versa. The PPTP users have no trouble accessing the resources on the site that they connect to. I have tried activating RIP and adding various static routes with no success. If I PPTP connect to site 1 and I tracert to an IP address on site 2 the route goes to the site 1 router and then goes to the internet(connected to the site 1 router) where it stops.
View 2 Replies
View Related
Aug 24, 2012
I am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies
View Related
Aug 19, 2011
I am looking to purchase the RV220W router. I am interested to know if I can use the iPhone/iPad to create a VPN connection to this router.I have seen a lot of conflicting information about this so I am looking for a confirmation.
View 15 Replies
View Related
Jan 25, 2012
My ISP provides IPv6 connectivity in the form of dual stack IPv4/IPv6 with DHCPv6 Prefix Delegation. Using a Cisco IOS-based router I managed to make such a connection by using as a template the Cisco IOS configuration file that my ISP has posted as an example in the following link:
[URL]
The main point on this configuration is a PPPoE connection with:
interface Dialer46
ipv6 address autoconfig default
ipv6 enable
[Code].....
configure this router according the Cisco IOS configuration file I linked on the top in order to have a working IPv6 connection?
View 4 Replies
View Related
Jan 14, 2013
I just purchased and installed a RV220W router. I bought it specifically for the VPN capability. After successfully setting up the QuickVPN and connecting, I am confused about how to setup the router (if possible) so I can run applications remotely. Is this possible with the RV220W and if so, is there documentation to guide me in the right direction?
View 5 Replies
View Related
Apr 27, 2013
I just bought a RV220W. One of the features I need to setup is a daily wireless plan, i.e. parental control: my wireless connection needs to be open at different times depending on the day, for 2 specific wireless devices, while others wireless devices have continuous access. Unfortunately, the wireless schedule only lets me set up one start/stop time only (i.e. the same one every day).
I noticed that I could possibly set up a firewall access rule with a specific schedule, but I have no idea if this would work, and how to set it up. My basic idea was then to open the wireless SSID I want to control from 7.30am to 11pm every day, and then add a firewall rule that would close the access to the said devices (using their MAC address) from say 10-11pm on given days... But I am not quite sure how to set this up.
View 2 Replies
View Related
Dec 3, 2012
I have a RV220W setup with SSL VPN users, authenticating to an internal Active Directory. Maybe 5 ports forwarded and 8 external IP addresses. Besides this i have 1 data VLAN and a voice vlan on my network.
The reboots are on different times on a day, even on Sundays at 7 AM when noone is logged in to the network.FW is at 1.0.4.17.
View 1 Replies
View Related
Sep 5, 2011
I have setup port forwarding on the RV220W, to allow outside connections on RDP. I have tested that LAN RDP works fine, but when I test using an outside address trying to connect to an inside windows PC with RDP nothing happens.
View 11 Replies
View Related
Jul 22, 2012
I have a site to site VPN tunnel configured between a rv220w and rv180. Everything works fine going from site to site on LAN connections. I'm now trying to tie in the remote site wireless (rv220w side) by pointing radius to my ACS server which is on the other side of the site-to-site tunnel but it seems as though it doesnt route across the site to site tunnel. If i put a radius server on the local lan on the remote site that authentication works fine. I have confirmed there are no ACL problems. the RV220W capable of using a radius server across the vpn tunnel?
View 1 Replies
View Related
Oct 8, 2009
I'm replacing my RVS4000 with the RV180 but having VPN connection issues with the RV180. Let me know the VPN tunnels work perfectly fine on the RVS4000.I have configured my RV180 for 3 VPN tunnels. My ISP is Comcast (cable) Business class with a Static IP. First VPN tunnel is to another Comcast ISP and the VPN works flawlessly - connects immediately.Second VPN Tunnel is to Business class ISP (Verizon-NJ) and VPN will NOT connect.Third VPN Tunnel is to Business class ISP (Cox Network-VA) and VPN will NOT connect.I had opened both the RVS4000 and RV180 up on a browser and both settings from the units were idential. I reconnect the RVS4000, VPN tunnels work great, I unplug and reconnect the RV180, the Comcast VPN works, but the other two do not.From what the log is saying "[IKE] WARNING: no phase2 found" and the other says "[IKE] ERROR: remote identifier not found". It has to be something with the RV180 that I'm missing or possibly configuring incorrectly.
View 3 Replies
View Related
Jun 12, 2012
Is there any way to setup an IPSEC tunnel to be able to go from my subnet, 192.168.75.x and be able to reach anything on the other side of the tunnel, 192.168.X.X?
View 5 Replies
View Related
Jul 21, 2011
I'm trying to set up a VPN tunnel between a Linux machine and a RVS4000 at a remote site (served via satellite connection). After many efforts, I finally succeeded (based on Openswan). However, while PINGing is OK, big packets (from the RVS4000 LAN to the Linux box) arrive corrupted.
I lowered the WAN MTU, with no success. What finally did the trick is to lower the MTU at the RVS4000 LAN interface. Since this is not possible via the Web I/F, I did it via telnet ("ifconfig eth0 mtu 1400"). However, this change is lost after router reboot. How can I make the LAN MTU setting permanent?
View 1 Replies
View Related
Aug 18, 2012
I bought 2 RV180 to setup a VPN tunnel between a remote site and central office.The VPN tunnel is established, I can ping from central office to remote site but browsing on that server fails. [code]
Seems the routing is not really working through the VPN Tunnel.
View 4 Replies
View Related
Apr 8, 2012
I have two Cisco RV8082 Routers which I would like to setup a VPN Tunnel with Gateway to Gateway. One location is a static IP Address. The other location is a dynamic IP address.
View 2 Replies
View Related
Feb 6, 2013
My router is a Dlink Model DI-624
My modem is an Arris Model TM502GI don't remember how to set it up. That is what cable goes where & is there anything to do on the PC With WiFi for it to connect with my router?I am 70 years old with a limited knowledge of computer and other electronic gadgets.
View 1 Replies
View Related
Oct 17, 2012
I am using a Cisco RV110W (Firmware 1.2.09) in a branch and I would like to create a VPN Tunnel to another site that has a Cisco RV042 (firmware v4.2.1.02)
What would be the correct Configuration? the current configuration I am using is
in the RV042 i am using
Check Enable
Local Group Setup
Local Security Gateway Type : IP Only
IP Address : RV042 Pulbic IP address
[Code].....
View 3 Replies
View Related
Mar 10, 2012
I'm currently trying to set up a Cisco RV220W router on our company's network to act as a network router and firewall, but I'm a little bit stuck.
The topology I want to achieve is as follows:
[WAN] --> [VDSL modem from ISP] --> [Cisco RV220W] --> [LAN]
Our LAN should have 2 VLANs; one for our servers and clients belonging to the company (servers are on public IPs, while clients have LAN IPs), and one for guest users (visitors and other outsiders who are given Internet access from us).
Our current network setup works just fine, using a bridged firewall server between the VDSL modem and the network switch (where all the other servers are connected), and internal users are routed through either a WLAN router or another server. The RV220W will replace the WLAN router as well as the routing and firewall servers, combining these tasks into one.
The target network setup would have three "zones";the servers (using IPs 213.x.x.0/26, static assignments, no DHCP), local LAN for employees (cable, WLAN or VPN with PPTP - using IPs 192.168.15.x/24 assigned by DHCP, compatible with the existing setup), and local LAN for visitors/guests (WLAN only, using IPs 192.168.0.x/24 assigned by DHCP).
From the RV220W's admin interface itself, I'm able to ping outside IP addresses, but neither the test server on the public IP or the test client on the local IP seems to be able to ping the outside, or eachother (ie. from the client's local IP to the server's public IP).
The Rv220W is already in router mode (ie. not in NAT mode), and the LAN ports are properly tagged for each network segment.
View 2 Replies
View Related
Jul 24, 2012
Environment :linksys wrt300n v1.1 which can have ddwrt-mega. Willing to tunnel all lan's outbound traffic through an ssh tunnel.
View 2 Replies
View Related
Nov 10, 2011
May I know that can a CISCO RV220W setup as a Access Point in company network? We already have a router for IP management. is it possible to setup as Acces point?
Also can we separate the guest and internal user for using wireless by difference SSID and VLAN. It seem it cannot setup if i need to setup limited network access right by SSID and VLAN.
View 3 Replies
View Related
Apr 12, 2013
I am trying to setup 4 cameras to view with remote live view. I set up my server with IP addresses of 192.168.1.80 .... 85. The screen has only the option for 1 video channel. I have seen on-line screen shots that have options for channel 1 through 8. I want to assign each camera to a different channel so I will be able to use remote live view to show all 4 cameras at the same time. I can only show one at a time. Do I need a different version than 3.3 or some obscure windows 7 setting?
View 5 Replies
View Related
Jan 13, 2012
I have recently bought two CISCO routers RV220W for our main and brach office mainly for VPN tunneling. I didnt know they are routers only not modems. so I have set it up using BT 2wire Router as modem only.
I have successfuly setup the routers and manage to establish the VPN tunneling between two routers. AS bt doesnt give static WAN IP address so I have used Dyndns which works fine. although I have 5 static ip address which cannot be used for WAN unless i cahnge to one IP address even then BT tech said it will not work.
when I created the tunnel i could ping both servers with their IP only not with the names. I can ping them fine locally. I could also see the network from branch office to main office but not from main office to branch office. today when I restarted the server I cannot ping both server i mean vice versa but VPN tunnel is established. now I cannot see the network from branch office to main office as well.
Both sites running windows server 2008 standard. main office server has 6 NIC cards two wwith public and three with private ip addresses, its also runing Terminal server, exchange, file etc. the branch office has two NIC card one with private and one with public ip. Intially I could establish the VPN tunnel as the network range was same on both sites so I changed one in th e10.0.0.0 range other in 192.168.1.0 range and VPN tunnel was established straightaway.
As soon as the VPN tunnel was created I manage to creat an external trust without any problems and both servers are added in each other forward zones as name servers.
in the main office the fues went off and I had to re-start the router and now the VPN tunnel is not establishing, mainly the error is ISAKMP-SA Expired I will paste the log of both routers below
1. How to Clear Old or Existing Security Associations (Tunnels) on RV220W
2. how to fix the problem where I can ping the server with their IP as well as domain names ?
3. how to set it up so that both sides can see the network resources as well as access it ?
4. how to set it up so if the staff in branch office wants to log on the domain in main office he can simply do it as he does it in his office.
View 7 Replies
View Related
Jul 9, 2012
i recently had att u vesre installed at my house with a 2 wire 3801 router/ modem but i cant get my xbox 360 online. how to configure the router for the xbox 360 so i can play xbox live.
View 1 Replies
View Related
Nov 20, 2012
I replaced a similar router from a competing company with the AC900 N900 router. I open Live Mail (IMAP) and keep it open during the day. Since switching over, when I periodically look at email on Live Mail, I frequently get a "Windows Live Mail" message saying "Your server unexpectedly terminated the connection. Possible causes for this include server problems, network problems, or a long period of inactivity." I have never received this message from either one of the previous routers - LinkSys, Netgear.
View 7 Replies
View Related
Dec 26, 2011
Our internet connection changed and so did our public IP addresses, I'm trying to re-establish our VPN tunnel with our client, but we haven't be able to get the connection back up even though only 2 IP addresses have changed. Below is my ASA 5510 config file Our WAN from the ISP is: 65.xx.xxx.104/30 and our LAN is: 67.xxx.xxx.128/27, I'm trying to use: 65.xx.xxx.106 as the endpoint and 67.xxx.xxx.130 as the host via the tunnel.
View 5 Replies
View Related
Jun 9, 2012
We have pair of ASA5585 (ver 8.4(4) with IPS module configured with Active/Standby failover. There are total 09 interfaces are connecting to different zones in the firewall and out of which three(3) interfaces are connecting to Palo Alto 2nd layer firewall. When we test the failover whatever interfaces not connecting Palo Alto failed or shutdown, ASA triggers the failover to other unit, however the Palo Alto is not detecting this failover and it still keeps its previous Active Palo Alto to pass traffic, thereby failing passing traffic on Active firewall through Standby Palo Alto firewall.
But when there's a interface failed or shutdonw on the interfaces where PaloAlto also connected, then once the ASA failover triggers and the same time Palo Alto also trigger its failover then both new active firewall and Palo Alto sending traffic through firewall.However we we cant all the interfaces of ASA also to connect Palo Alto and let the Palo Alto to inspect all the interfaces, but we need our ASA to work in a situation where any of the interfaces failed, the failover to work smooth the pass the traffic via either Palo Alto device.I just need to know is there anything tricky that we can configure on our ASA in this failover senario, or to confirm if there's no any workable solution to this situation.
I have attached the senario that I explained above. Just to emphasis the issue again, if any interface of Gig0/0, Gig0/4 or Gig0/5 failed on active firewall, ASA switching to standby firewall and act as Active, but Palo Alto still remains his Active state and the new Active ASA is not passing traffic via standby PA as its not detecting any of its interfaces as failed or unreachable..?
View 1 Replies
View Related
Jan 17, 2012
Had just purchased a new DCS942L unit and had it setup fine. Registered it on the web and the web stated that it needed a firmware update. Connected with hard line and started update. After 5min webapp said device timed out. When I went to rest camera could no longer get a connection of any kind.
View 1 Replies
View Related
Nov 25, 2012
I've been labbing on my asa5505 at home, setting up different VPN solutions for testing purposes. However, I can't get my anyconnect client to establish a DTLS tunnel when connecting (anyconnect only shows tls, and does not display any errors about not connecting with dtls)I have set dtls port to 444 and this port is open on the other side.
View 2 Replies
View Related
