I have interfaces defined on the 5505:
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
[Code].....
I only need one interface to connect to a single host on the inside (VLAN1) and then connect E0 to a DSL.
Is it possible (are what are the commands required) to take one of the other interfaces and create a Management port on the local office LAN?
I have got ASA 5520. How to use the management port as a normal port on ASA. What are the basic reqirements for that.
View 3 Replies View Relatedwe are having a firewall asa 5520 .we have connected the management port and inside port to internal network and dmz port to dmz network.now we need to configure tacacs and other management tool on dmz devices through management port. The problem is the management devices tacacs and other are placed in internal network.
View 2 Replies View RelatedIt's a problem about access ASA5500 Firewall mangement port. The customer request access ASA5500 by entering the default IP address https://192.168.1.1 to monitor data tracffic in Windows 7. But after entering the default IP in IE, no any page appear.
But that way can access ASA5500 magement port successfully in Windows XP. What the different between Windows 7 and Windows XP? Is there any way or any patch can access ASA5500 manemeng port in Windows 7?
I've got a client with a Management Port set up for Out-of-Band management. Here's the configuration of the interface and some relevant static routes:
interface Management0/0
description MGT
speed 100
duplex full
nameif Mgt
[code]...
The route through Mgt interface is required as my client accesses the device from a subnet that isn't local to M0/0.Unfortunately, now any traffic originating from outside and destined to 10.48.0.0/16 is choosing the Mgt interface. I had thought that the 'management-only' keyword prevents this from happening (traffic traversing between interfaces).
There is a broad scope of /16 addresses on the 'inside' so just swapping destinations won't work (the client wants to avoid a routing table with 50+ static entries, understandably)My temporary solution was to do this:
route inside 10.0.0.0 255.128.0.0 10.38.103.1
route inside 10.128.0.0 255.128.0.0 10.38.103.1
route Mgt 10.0.0.0 255.0.0.0 10.38.100.254
If 'management-only' doesn't prevent traffic from using the Mgt interface, what is the point of the command?
I have a Windows 2003 server running a L2TP VPN server on it. I'm putting theASA5505 in replacement of an open source firewall.
My question is that, I can't seem to forward the ports correctly for L2TP to the internal address of the 2k3 VPN server. It seems to me that the ASA is trying to negotiate the VPN connection rather than forward it internally.
Cisco ASA5505
WAN 216.136.1.2
LAN 10.1.1.1/24
Windows server - 10.1.1.14
I've added the NAT and ACL and still nothing.
I'm not able to access my Slingbox from the outside. I've set up port forwarding on port 5001 to allow outside connections in, but port forwarding isn't working. Am I missing something?
object network INSIDE-HOSTS
subnet 10.10.10.0 255.255.255.0
object network Slingbox
host 10.10.10.254
object-group protocol TCPUDP
[code].....
I just bought a Cisco ASA5505. I'm trying to opening a port range through CLI, but it doesn't seem to be working.
Background:I have an FTP Server running behind the firewall and need to allow port ranges 30000-30100 for data connections. I have been using FTP through the command prompt and its working. However, I cannot use it through the FileZilla client as it fails to query the directories. I have the ASA forwarding to port 1125 from 21 in passive mode.
Access-List:
access-list Outside_Access_In line 3 extended permit tcp any any eq ftp-data (hitcnt=0) 0xfa8ed43d
access-list Outside_Access_In line 4 extended permit tcp any any eq ftp (hitcnt=17)
[Code].....
I am at a loss on configuring a new ASA5505 for multiple static port translations.I would have expected to simply add several service command to a network object to complete the task, however, the service command overrides the previous and replaces rather than adds to the translations. [code] However, if entered in that order the 8443 overwrites the 8080 static translation.What is the correct procedure to establish multiple translations? If someone could also provide the "old" style for pre 8.2 release, I'd like to compare because I thought I used to do this with an access-list somewhere.
View 4 Replies View RelatedI have an ASA 5505 on a job. It is a smaller business that would have done better with an RV082, but they have what they have. It is running firmware 8.4. The client needed ports forwarded for their FTP server. The port range in this config is tcp 43333-43339. The FTP server ip is 192.168.1.2. [Code] ......
View 8 Replies View RelatedI've had a Cisco ASA 5505 firewall connected to a cable modem (Virgin Media, UK) for the past 3 years. In the last 6 months or so I have noticed that the ASA would drop the outside (internet) connection intermittently, usually at least once every 1-2 weeks - the interface still shows as being up but no traffic crosses it, and computers on the inside network abruptly lose internet connectivity. Rebooting the ASA or administratively shutting down the interface and bringing it back up again would cure the problem straight away until the next time it happens.
In the last couple of days however despite nothing having been changed in the configuration the frequency of this connection drop has increased to the point where I would lose access to the internet within an hour of rebooting the ASA. It does not seem to matter whether or not there is traffic currently going out or not, inside computers just appear to suddenly lose internet connectivity.
I have tried the following without success:
1) I completely wiped the configuration (configure factory-default)
2) I changed the port the cable modem was connected to (eth0/0 -> eth0/7, changing switchport vlan accordingly)
I thought perhaps 2) had fixed it but it lasted a whole 2 hours before I woke up this morning to find that none of the internal equipment had internet access despite the fact eth0/7 was showing as up/up in ASA CLI.
This morning I manually set the eth0/7 port to "speed 10" (10Mbps, full duplex). It was previously set to be auto-negotiation (default) on both speed and duplex. As of this post it has managed to keep the outside connection up for 3 hours - but I'm not optimistic that it is fixed.
Interface counters have never shown any collisions, errors, etc - only packets input and output as expected.
Since the problem persisted across ports (eth0/0 -> eth0/7) I'm wondering whether or not the problem could either be faulty memory, or some kind of speed/duplex incompatibility between the cable modem and ASA.
How to configure this setup.I have an ASA5505 with dual wan failover, FiOS (eth0) & Cable (eth1). how to configure the port forwarding for all my devices so it doesn't matter what external interface the traffic is coming from. For example, I need web traffic on port 80 forwarded to 192.168.1.150 regardless of whether it is coming through eth0 or eth1.
View 2 Replies View RelatedASA5505 port 3306.I have been fighting for days to open the port 3306 on my appliance, I have read carefully all the forums and no success.
View 9 Replies View RelatedI have installed ASA5505 in the network. Port forwarding has been done for one of the server in our LAN. Public users are able to access the server successfully. I am trying to access from inside using the same Public server IP, but unable to access it. Can I have this feature in ASA5505(I think it is loopback configuration). If so, may I know the configuration detail?
View 4 Replies View RelatedI am a total Cisco novice who has just had a ASA5505 installed to replace a linux freeware firewall (smoothwall).I'm told that the 5505 can't port forward traffic (e.g. ssh) from two external IP addresses to two internal destination machines via the same port # (22 in this example).
View 9 Replies View RelatedI thought I had the configuration to allow bi-directional traffic for my Blackberry server. I have a second fw with the same config and it worked on that one. But right now, my blackberry server is down, and all the users are upset.
ASA Version 8.2(2)
!
hostname asa5505
[Code]......
configuring the ASA particulary after the change to how NAT is implemented. What I am trying to accomplish logically seems fairly simple, yet I cannot get it to work. I have a Synology NAS at home that I am trying to reach via the internet. Prior to using my ASA, I had Verizon's FIOS router as my gateway and everything forwarded with no issues. The ports I need forwarded or reachable via the internet are TCP port 80 and 5000.I can also configure it via command line if that's the easier/preferred method.
View 11 Replies View RelatedASA 5505 Firmware 8.3(4), ADSM 6.4(2).I have a public IP address of 168.87.3.4.I need to forward ports (5060, 5080, etc.) to one internal address. (192168.1.1).I need to foward different ports (10020-10080) to a different internal address (192.168.1.2) Everything I read tells me how to do this in a 1 to 1 static NAT.
View 1 Replies View RelatedI have an all gigE 3560. I don't use the management FE0 port on the back. I was thinking to use that for a 100Mbps WAN connection.
Seems to work just fine when I plugged in an test. But I am not routing across that link yet as I still need to setup the far end.
Is there any reason this would not work? I would like to not burn a gig port if the max throughput of the circuit is 100Mbps.
I saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies View RelatedI just purchased 2 SF-300 48 port units for 2 customers. I want to be able to remotely manage them over the Internet with my browser. BUT, customer sites already use port 80 for web servers. So, how do I configure this switch to use some other port than 80?
I called support, and much to my surprise he said it cannot be changed. How bizarre that a device with many hundreds of configuration settings does not have one of the most basic settings...
At one customer site I can configure port forwarding and translation to get around this problem, but the other site's router does not offer port translation..
I'm having an issue with the 5508 management port .. I can't seem to ping it from the switch connected to it .. ( the Show cdp command shows that the two can see each other .. but no ping is possible ! [code]
View 4 Replies View Relatedi am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration
View 1 Replies View RelatedIs it possible to use the mgmt port when in rommon mode? I use the Mgmt port when IOS is loaded and it works fine. I reboot the router, issue a break to put it in rommon and have set some variables but my Mgmt port never has link and I cannot ping it from the network. In rommon mode it looks like this:
PS1=rommon ! >
MCP_STARTUP_TRACEFLAGS=00000000:00000000
BOOT=bootflash:asr1000rp1-adventerprisek9.03.07.03.S.152-4.S3.bin,1;
IP_ADDRESS=10.71.50.101
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.71.50.3
BSI=0
RANDOM_NUM=1133006948
RET_2_RTS=13:38:27 EDT Wed Jun 5 2013
RET_2_RCALTS=1370453907
?=0
How does the IP address is assigned on management port of WS4507 R, syntax.
View 2 Replies View Relatedis it possible to Manage the 2504 Controller over a separate Interface. Exmaple: Port 1 is used as controller management interface (untagged) - AP's are connected to the same VLAN Port 1 is used for Guest Traffic (VLAN 3 tagged) Port 2 should be used to manage the WLAN Controller from the internal LAN. (tested with untagged, tagged, same issue)
with this Setup it is possible to ping the Port 2 IP-Address from the internal LAN but if you try to connect to the controller, the Browser shows "Site not reachable".
I also enabled "Management via Wireless" but without success. I also tried to add the "management" VLAN as tagged on the management Interface with the same effect, the controller is not manageable from the internal LAN. On 5508 WLAN Controller i have an similar setup, but with LAG Port enabled. There this works.
The only interface were i can manage the WLAN controller is from the management Interface.
Is there some kind of trick to getting the fastethernet 0 management port to come up? My adjacent switch is up/up, but fe0 is down/down. I dont' see how this could be possible. I am getting all my info remotely, but I am pretty sure it's wired up correctly.
View 2 Replies View RelatedI have a brand new RV042 v3 that I just updated to the latest firmware (v4.2.1.02) and have stumbled across an anomaly... I can only access the router from the WAN port using port 80. I happen to have it set to port 8080, but that doesn't work; I have to use standard port 80.
I have two other RV042 units running older firmware and they work as expected and follow the port that is filled in. This one has me puzzled and wondering if this is a bug in the firmware.
I have an asa 5520. How would I configure my dedicated management interface to be able to route off subnet while the firewall is in transparent mode?
View 1 Replies View RelatedI have a cisco 6509 configured with a cisco NAM module. I have reset the config of the NAM module by the config clear command. Since this moment I can't no more ping the NAM module via the management port: OK via the 127.0.0.91 address and log in ok via the ios cli session command. [code] I have already tried to reboot the module via the ios cli hw module command and nothing better.
View 12 Replies View Relatedrecently got a RV220W and liking all the configuration options.
Although I cannot find where to change the listening port for management? I want it to listen on port 81 instead of 80.
I have 2 x 5508 Wireless Controllers, 1 mgmt port on each as standard. I noticied something different between these controllers running the same code.I can bound a physical port to the mgmt interface on one controller but not the other (both interfaces are untagged)see below, this config appears on one controller but not the other? Is this something to do with the initial setup? How can I add Phyiscal information to the other controller mgmt interface, I cannot delete the mgmt interface. Physical InformationPort Number Backup Port Active Port Enable Dynamic AP Management?
View 2 Replies View RelatedWhat is the point of it? It is not a remote console. If i reboot the switch i cannot get back to the out of band management port unless the switch is fully running. Is this only for security purposees? so all telnet/ssh is from an Out of band network?
View 15 Replies View Related