we are having a firewall asa 5520 .we have connected the management port and inside port to internal network and dmz port to dmz network.now we need to configure tacacs and other management tool on dmz devices through management port. The problem is the management devices tacacs and other are placed in internal network.
View 2 RepliesI have got ASA 5520. How to use the management port as a normal port on ASA. What are the basic reqirements for that.
View 3 Replies View RelatedI have an asa 5520. How would I configure my dedicated management interface to be able to route off subnet while the firewall is in transparent mode?
View 1 Replies View RelatedI have two ASA 5520 with 4 Giga interfaces and 1 management interface.
I need to use 4 interfaces four data traffic
1- Inside
2- Outside
3- dmz-1
4- dmz-2
The remaining will be the management interface only.How can I configure the Statefull failover and Management?
1- I used the management0/0 for The stateful failover.
2- I used gig 0 for outside
3- I used gig 1 for inside
4- I used gig 2 for dmz-1
5- I divided the gig 3 to two sub interfaces
a- gig0/3.1 for dmz-2
b- gig0/3.2 for Management and I defined it as a management-only
I have interfaces defined on the 5505:
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
[Code].....
I only need one interface to connect to a single host on the inside (VLAN1) and then connect E0 to a DSL.
Is it possible (are what are the commands required) to take one of the other interfaces and create a Management port on the local office LAN?
It's a problem about access ASA5500 Firewall mangement port. The customer request access ASA5500 by entering the default IP address https://192.168.1.1 to monitor data tracffic in Windows 7. But after entering the default IP in IE, no any page appear.
But that way can access ASA5500 magement port successfully in Windows XP. What the different between Windows 7 and Windows XP? Is there any way or any patch can access ASA5500 manemeng port in Windows 7?
I've got a client with a Management Port set up for Out-of-Band management. Here's the configuration of the interface and some relevant static routes:
interface Management0/0
description MGT
speed 100
duplex full
nameif Mgt
[code]...
The route through Mgt interface is required as my client accesses the device from a subnet that isn't local to M0/0.Unfortunately, now any traffic originating from outside and destined to 10.48.0.0/16 is choosing the Mgt interface. I had thought that the 'management-only' keyword prevents this from happening (traffic traversing between interfaces).
There is a broad scope of /16 addresses on the 'inside' so just swapping destinations won't work (the client wants to avoid a routing table with 50+ static entries, understandably)My temporary solution was to do this:
route inside 10.0.0.0 255.128.0.0 10.38.103.1
route inside 10.128.0.0 255.128.0.0 10.38.103.1
route Mgt 10.0.0.0 255.0.0.0 10.38.100.254
If 'management-only' doesn't prevent traffic from using the Mgt interface, what is the point of the command?
We have an ASA 5520 and it's inside interface is currently plugged into a fast ethernet port on a 3750. I have just bought a 1gig SFP module and have copied the fast ethernet port config to the gigabit port, but the port seems to be flapping
The port conf gi is this:
interface GigabitEthernet1/0/4
description Link to Inside ASA
switchport access vlan 2
switchport trunk encapsulation dot1q
In a cisco firewall 5520 how could you take a public wan connection and pass it to another firewall behind the 5520 without using nat. How could you put a single port on the 5520 into transparent or passthrough much like you can on a broadband modem?
View 3 Replies View RelatedI have an ASA 5520 Cisco Adaptive Security Appliance Software Version 8.4(2)8 Device Manager Version 6.4(5)206. I am trying to add a nat for outside x.x.x.77 port going inside x.x.x.22 port 80 . the wan interface is .74 with subnet of 255.255.255.248 the rule will add but traffic wont pass in.
View 14 Replies View RelatedI am trying to forward all the traffic of a particular port number to my outside interface forwarded to an internal IP address.
View 1 Replies View RelatedSo everything I've read on Cisco's documentation here: URL says that I can create a port-channel on two physical interfaces that will uplink to a VSS pair. However, the command is not recognized. What am I missing? I've tried executing "channel-group #" on the physical interface and tried creating the port-channel 1st and neither commands exist. I haven't seen it listed anywhere if it is only available after a specific piece of ASA software. If it is the software what version at a minimum I need to upgrade to? Below is an output from a show version
Cisco Adaptive Security Appliance Software Version 8.0(4)
Device Manager Version 6.1(3)
Compiled on Thu 07-Aug-08 20:53 by builders
System image file is "disk0:/asa804-k8.bin"
Config file at boot was "startup-(code)
I have a cisco asa 5520. i need to forward telnet to a router on the inside interface. Here is what i have done so far but it doesnt seem to be working.
I have created an access-list that looks like this:
access-list 102 extended permit tcp any host 10.10.60.2 eq telnet
But when do this it still doesnt forward my request to the router at 10.10.60.2 . So just to explain what im trying to do. I use Putty, i am putting the outside interface IP into putty, selecting telnet and opening the session. i need the outside interface to see this request and know to forward port 23 to the router on the inside interface with IP 10.10.60.2. The ASA is running version: asa842-k8.bin
I am trying to correctly configure our ASA 5520 and our Mitel Border Gateway in our DMZ. In the documentation for the Mitel border gateway it wants me to set up 2 external IP's on my ASA one to allow 443 traffice into the MBG, and another for 443 traffic that needs to be forwarded to port 4443 for the MGB in the DMZ. My problem is I don't know how to do this. the MBG only has one IP, and I need to have 2 different URL's mapped to two different external IP's both externally using port 443, and one of them forwarding to 4443 on the DMZ interface.
View 10 Replies View RelatedI am having cisco asa 5520 with internet having public ip and cisco 2911 with mpls link in my office. the mpls link is between my HO and my branchmi am putting my webserver in the branch side i want to port forward one of my publicip in my office to be forwarded to branch we, server.is it poosible on the firewall ouside the local network.
View 3 Replies View RelatedI need to allow traffic between webserver in dmz and mssql (Microsoft SQL Server 2008).MSSQL use dynamic port (now it is 63796) and this cannot be changed.
Basically, I can allow such traffic using next configuration:access-list dmz extended permit tcp host 1.2.3.4 host 5.6.7.8 eq 1433access-list dmz extended permit udp host 1.2.3.4 host 5.6.7.8 eq 1434 access-list dmz extended permit tcp host 1.2.3.4 host 5.6.7.8 eq 63796
But, I would like to add mssql inspection and I did the next:
class-map class_sqlnetmatch port tcp eq 1433policy-map global_policyclass inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp class class_sqlnet inspect sqlnet service-policy global_policy global
[Code] ..........
I have an ASA 5520 and I'm using Solar winds real time interface tool to monitor the through put of the port. It seems I can never get it to use more than 100mb, where should I check?
I have run a sh int giga 0/1 and it shows the port is 1000mb full duplex and the I have also checked the other end where it plugs into the LAN and this also says the port is running at 1000mb full duplex.
I'd like to see some REAL LIFE comparisons of ASA firewall throughput (a bit like this one for ISR G2 Routers - [URL].
The reason I ask is that I recently upgraded a firewall from an ASA5505 to an ASA5520 on a small network where the only outside connectivity was a single 10meg Internet circuit with an IPSEC VPN (not landed on the firewall but on a router) to another site.
When I swapped out the firewall the users noticed a big improvement. The firewall is not doing anything out of the ordinary - no IPS or VPN, just standard state full inspection.
We are using the newest release of AD Agent (1.0.0.32.1, built 598). The ASA Firewalls 5520 are having the software release 8.4(3)8 installed.When somebody tries to connect thru the Identity based firewalls from a citrix published desktop environment (PDI) the connection is not possible. Checking the ip-of-user mapping on the firewalls (show user-identity ip-of-user USERNAME) mostly doesn't show the mapping of the USERNAME and the PDI the user is logged in. The user-of-ip mapping of the PDIs IP-address shows mostly other users, which then are used to authenticate the acces thru the firewalls.
What is interesting, that on the AD Agent using "adacfg.exe cache list | find /i "USERNAME"" i can't see the PDIs IP-address neither because it is mapped to another user.Is Citrix Published Desktop environment supported to connect thru Identity based Firewalls? How AD Agent, Domain Controllers and Firewalls are working together? On the firewalls with "show user-identity ad-agent we see, the following:
-Authentication Port: udp/1645
-Accounting Port: udp/1646
-ASA Listening Port: udp/3799
Why Cisco does use 1645 and 1646 and not 1812 and 1813?The Listening Port is used for what purpose? we tried the AD Agent modes full- download and on-demand with the same effect.
I try to launch a LAND Attack against my firewall ASA 5520. Everything will work fine. But why, I think it should not work. I use a little tool where I can user a spoofed address, with a cluster shell and attack the firewall interface with the source of 127.0.0.1 ore the ip address of the interface as the source and destination. Then I get a cpu load of 89% with only two host. With IP tables I can use kernel processes to prevent this. But I don´t find anything for ASA.
View 1 Replies View RelatedTwo different WAN links get connected to the firewall via two routers.(Different ip subnets).I need to get this two wan streams seperatly to the core switches.Core switches sits.Active/Stanby senario. If the Active core goes down Stndby Core will have take over the traffic. My design is correct ,if not what do i need to change. ASA is 5520.
View 8 Replies View RelatedI have ASA 5520 installed. I want to use ntp server for firewall clock setting. I found one open-access ntp server (stratum 2) in Los Angeles:
[URL] 209.151.225.100
Can I use the following command to set ntp server?
ntp server 209.151.225.100 source outside.
communication between 2 vlans.i have 2 vlans
Vlan 100
ip add 1.1.1.1
!
!
!
Vlan 200
ip add 2.2.2.2
i want to make communication between 2 vlans on firewall 5520 ASA 8.2.
I have a serious problem with my corporate firewall, witch is an ASA 5520, fv 8.3, with 8 +1 interfaces. It suddenly started to crash every 10/20 minutes and rebooting alone.
First of all I checked system resources witch are in a very low usage state. I also checked interfaces errors, but nothing strange come out o from error counters analysis. I tried disabling logging and all the service policy rules configured, but nothing changed.
Nothing changed and firewall continue restarting by itself.
Last logs I received before crash were:
%ASA-4-711004: Task ran for 35 m sec, Process = Dispatch Unit, PC = 84a619e, Call stack =
%ASA-4-711004: Task ran for 35 m sec, Process = Dispatch Unit, PC = 84a619e, Call stack = 0x084A619E 0x084A6512 0x084A70E1 0x084A7987 0x084A7AAA 0x08558B9B 0x08558E8A 0x083D3518 0x083CA145 0x080659D1 0x089196D9 0x08919790 0x089FF711 0x08A27468
Here the sh crash info command on module 0, after last reboot:
[Code] ......
I have an ASA 5520 in my company which does all our NAT and Firewall access control. Currently there is a rule in place to allow an incoming connection on port 2222 from a specific ip address to allow access to a web app our developers created. This is a test before the web app is released live. Now the web app can communicate with the specific address and port but the incoming connection on port 2222 isn't getting through. Everything looks great in the firewall but how can I log any hits this ACL takes to identify any potential problems?
View 2 Replies View RelatedOur Local Network is behind the CISCO ASA Firewall.Whenever we are accessing to Client VPN server,it is getting connected but after few Minutes (May be 5/10/30 Min),the sessions are terminating. The same traffic through PIX is no issue , only with ASA Firewall. See the following Error and request you give the possible root cause for this.
2011-04-09 16:15:09 Local4.Info 172.16.1.68 %ASA-6-302016: Tear down UDP connection 87447908 for OUTSIDE:68.22.26.66/4500 to inside:172.16.9.10/4410 duration 0:27:49 bytes 18653
I have problem in the configuration of Cisco ASA 5520, IOS version 8.4. The connection is as follows: LAN network--> Firewall --> Routers with GLBP with virtual ip address. the clients can not ping the virtual interface of the GLBP group, but I can ping it from the firewall, and I can ping the clients from the firewall, I checked the packet tracer it gives :
Phase: 7
Type: NAT
Subtype:
Result: DROP
Config:
nat (inside10,outside) source dynamic LAN interface
Additional Information:(code)
Need to know if ASA 5520 does Layer 7 firewall or not?
View 2 Replies View RelatedTwo days ago, we changed our old 525 with asa 5520 ( ver 8.2 ). Configuration is the same, except the version. It even retains the same global interface and static public ip address as the old device.All worked well during that period.
Yesterday, one of the http applications , not tested other day, was found not to be working. To test, we switched back to the old 525 , however nothing was working when we did that.
I would just like to to open UDP port 123 in the ASA 5510 Firewall so that our Primary Domain Controller could use this port to sync time with an external time source. We have already added an access rule for this port under the firewall configuration in ASDM 6.4 and this port was also allowed in the inbound and outbound rule of the PDC's Firewall but it seems that it was still blocked.
View 23 Replies View RelatedI have an issue with my firewall,each time i configured a trunk port in the firewall and connect a sw 2960S with a trunk port also, all the interfaces in the Firewall go down ( virutal intertaces, inside, outside , dmz) , also another switch 3750 that is connected to another port in the firewall( access port only) it start to a new negotiation of spanning tree.What could be causing this problem? the firewall didnt sedn bdpdu i think the IOS of the firewall its a 8.2
View 3 Replies View RelatedI am trying to get an ASA5510 working in transparent mode, multi-context. I am on revision 8.2.5, so there are no bridge groups (those are enabled in 8.4). I first set it to transparent mode, then set it to multi-context mode. I am doing trunking through the Ethernet0/0 to Ethernet0/1, and have two vlans on subinterfaces of each interface. These interfaces are in the 2nd and 3rd contexts, and all trunking between vlans is working correctly in transparent mode.
But I can't telnet or ssh to the ASA itself.
I have an IP address on the inside vlan interface in
I have 20 mbps internet link and I have ASA 5505 . I have to divide this bandwidth 10-10 mbps each for Voice and Data . So that both can work properly. because when I am using it for both on same interface, I am getting Voice disturbance..
View 1 Replies View Related