Cisco Firewall :: 5520 - Use Management Port As Normal Port On ASA
Jan 2, 2012I have got ASA 5520. How to use the management port as a normal port on ASA. What are the basic reqirements for that.
View 3 Replies
ADVERTISEMENT
Cisco Firewall :: 5520 Firewall Management Port
Nov 29, 2011we are having a firewall asa 5520 .we have connected the management port and inside port to internal network and dmz port to dmz network.now we need to configure tacacs and other management tool on dmz devices through management port. The problem is the management devices tacacs and other are placed in internal network.
View 2 Replies View RelatedCisco Switching/Routing :: 888w - Way To Change Usage Of ISDN Port To Normal RJ45 Port
Sep 25, 2012I have Cisco 800 series (888w) with BRI-ISDN port. Is there any way to change the usage of ISDN port to normal RJ45 port?I want to use this SOHO router to sharing connection.
View 0 Replies View RelatedCisco Firewall :: ASA 5520 - Moving Inside Port To 1gb SFP Port
Jun 11, 2012We have an ASA 5520 and it's inside interface is currently plugged into a fast ethernet port on a 3750. I have just bought a 1gig SFP module and have copied the fast ethernet port config to the gigabit port, but the port seems to be flapping
The port conf gi is this:
interface GigabitEthernet1/0/4
description Link to Inside ASA
switchport access vlan 2
switchport trunk encapsulation dot1q
Cisco Switching / Routing :: 3560 - Management Port Used As Regular Port?
Jan 30, 2012I have an all gigE 3560. I don't use the management FE0 port on the back. I was thinking to use that for a 100Mbps WAN connection.
Seems to work just fine when I plugged in an test. But I am not routing across that link yet as I still need to setup the far end.
Is there any reason this would not work? I would like to not burn a gig port if the max throughput of the circuit is 100Mbps.
Cisco Firewall :: Management Port On ASA5505?
Nov 7, 2011I have interfaces defined on the 5505:
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
[Code].....
I only need one interface to connect to a single host on the inside (VLAN1) and then connect E0 to a DSL.
Is it possible (are what are the commands required) to take one of the other interfaces and create a Management port on the local office LAN?
Cisco WAN :: Possible To Access ASA5500 Firewall Management Port
Jul 17, 2012It's a problem about access ASA5500 Firewall mangement port. The customer request access ASA5500 by entering the default IP address https://192.168.1.1 to monitor data tracffic in Windows 7. But after entering the default IP in IE, no any page appear.
But that way can access ASA5500 magement port successfully in Windows XP. What the different between Windows 7 and Windows XP? Is there any way or any patch can access ASA5500 manemeng port in Windows 7?
Cisco Firewall :: Management Port Routing On ASA5525x?
Jan 17, 2013I've got a client with a Management Port set up for Out-of-Band management. Here's the configuration of the interface and some relevant static routes:
interface Management0/0
description MGT
speed 100
duplex full
nameif Mgt
[code]...
The route through Mgt interface is required as my client accesses the device from a subnet that isn't local to M0/0.Unfortunately, now any traffic originating from outside and destined to 10.48.0.0/16 is choosing the Mgt interface. I had thought that the 'management-only' keyword prevents this from happening (traffic traversing between interfaces).
There is a broad scope of /16 addresses on the 'inside' so just swapping destinations won't work (the client wants to avoid a routing table with 50+ static entries, understandably)My temporary solution was to do this:
route inside 10.0.0.0 255.128.0.0 10.38.103.1
route inside 10.128.0.0 255.128.0.0 10.38.103.1
route Mgt 10.0.0.0 255.0.0.0 10.38.100.254
If 'management-only' doesn't prevent traffic from using the Mgt interface, what is the point of the command?
Cisco Firewall :: Port Passthrough On 5520?
Jan 13, 2012In a cisco firewall 5520 how could you take a public wan connection and pass it to another firewall behind the 5520 without using nat. How could you put a single port on the 5520 into transparent or passthrough much like you can on a broadband modem?
View 3 Replies View RelatedCisco Firewall :: 5520 / Add NAT For Outside X.x.x.77 Going Inside X.x.x.22 Port 80?
Oct 3, 2012I have an ASA 5520 Cisco Adaptive Security Appliance Software Version 8.4(2)8 Device Manager Version 6.4(5)206. I am trying to add a nat for outside x.x.x.77 port going inside x.x.x.22 port 80 . the wan interface is .74 with subnet of 255.255.255.248 the rule will add but traffic wont pass in.
View 14 Replies View RelatedCisco Firewall :: Port Forwarding In ASA 5520?
Oct 3, 2012I am trying to forward all the traffic of a particular port number to my outside interface forwarded to an internal IP address.
View 1 Replies View RelatedCisco Firewall :: Port-channel On ASA 5520
Jun 11, 2013So everything I've read on Cisco's documentation here: URL says that I can create a port-channel on two physical interfaces that will uplink to a VSS pair. However, the command is not recognized. What am I missing? I've tried executing "channel-group #" on the physical interface and tried creating the port-channel 1st and neither commands exist. I haven't seen it listed anywhere if it is only available after a specific piece of ASA software. If it is the software what version at a minimum I need to upgrade to? Below is an output from a show version
Cisco Adaptive Security Appliance Software Version 8.0(4)
Device Manager Version 6.1(3)
Compiled on Thu 07-Aug-08 20:53 by builders
System image file is "disk0:/asa804-k8.bin"
Config file at boot was "startup-(code)
Cisco Firewall :: Port Forward Telnet On ASA 5520?
Sep 26, 2012I have a cisco asa 5520. i need to forward telnet to a router on the inside interface. Here is what i have done so far but it doesnt seem to be working.
I have created an access-list that looks like this:
access-list 102 extended permit tcp any host 10.10.60.2 eq telnet
But when do this it still doesnt forward my request to the router at 10.10.60.2 . So just to explain what im trying to do. I use Putty, i am putting the outside interface IP into putty, selecting telnet and opening the session. i need the outside interface to see this request and know to forward port 23 to the router on the inside interface with IP 10.10.60.2. The ASA is running version: asa842-k8.bin
Cisco Firewall :: Can The ASA 5520 Do Traffic Shaping Or Policy Map Just Like In A Normal Router
Feb 13, 2011ASA 5520 can handle 2 ISP? not to load balance or not standby/active but to use the 2 ISP at the same time and separately. for example, ISP_A who has 10m will be dedicated to the customer A/VLAN A, then ISP_B who has 4m will be for the rest of the customer's traffic. Can the ASA 5520 do traffic shaping or policy map just like in a normal router?
View 5 Replies View RelatedCisco Firewall :: ASA 5520 Address Translation And Port Forwarding
Oct 31, 2011I am trying to correctly configure our ASA 5520 and our Mitel Border Gateway in our DMZ. In the documentation for the Mitel border gateway it wants me to set up 2 external IP's on my ASA one to allow 443 traffice into the MBG, and another for 443 traffic that needs to be forwarded to port 4443 for the MGB in the DMZ. My problem is I don't know how to do this. the MBG only has one IP, and I need to have 2 different URL's mapped to two different external IP's both externally using port 443, and one of them forwarding to 4443 on the DMZ interface.
View 10 Replies View RelatedCisco Firewall :: Asa 5520 Port Forwarding On Mpls Link
May 26, 2012I am having cisco asa 5520 with internet having public ip and cisco 2911 with mpls link in my office. the mpls link is between my HO and my branchmi am putting my webserver in the branch side i want to port forward one of my publicip in my office to be forwarded to branch we, server.is it poosible on the firewall ouside the local network.
View 3 Replies View RelatedCisco Firewall :: ASA 5520 - Inspection Of MSSQL Dynamic Port
Jun 5, 2012I need to allow traffic between webserver in dmz and mssql (Microsoft SQL Server 2008).MSSQL use dynamic port (now it is 63796) and this cannot be changed.
Basically, I can allow such traffic using next configuration:access-list dmz extended permit tcp host 1.2.3.4 host 5.6.7.8 eq 1433access-list dmz extended permit udp host 1.2.3.4 host 5.6.7.8 eq 1434 access-list dmz extended permit tcp host 1.2.3.4 host 5.6.7.8 eq 63796
But, I would like to add mssql inspection and I did the next:
class-map class_sqlnetmatch port tcp eq 1433policy-map global_policyclass inspection_default inspect dns preset_dns_map inspect ftp inspect h323 h225 inspect h323 ras inspect ip-options inspect netbios inspect rsh inspect rtsp inspect skinny inspect esmtp inspect sqlnet inspect sunrpc inspect tftp inspect sip inspect xdmcp class class_sqlnet inspect sqlnet service-policy global_policy global
[Code] ..........
Cisco Firewall :: ASA 5520 - Solar Winds Real Time Interface / Monitor Through Put Of Port?
Jul 6, 2012I have an ASA 5520 and I'm using Solar winds real time interface tool to monitor the through put of the port. It seems I can never get it to use more than 100mb, where should I check?
I have run a sh int giga 0/1 and it shows the port is 1000mb full duplex and the I have also checked the other end where it plugs into the LAN and this also says the port is running at 1000mb full duplex.
Cisco Firewall :: 5505 Static Nat With Port Redirection 8.3 Access List Using Un-Nat Port
Aug 15, 2012I am having difficulty following the logic of the port-translation. Here is the configuration on a 5505 with 8.3,So I would have thought the outside access-list should reference the 'mapped' port but even with 3398 open I cannot remote desktop to the host. If I open 3389 then I can connect successfully.
View 12 Replies View RelatedCisco Firewall :: Change Default SSH Port On ASA 5505 (port Forwarding)
Dec 2, 2011So here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
Cisco Firewall :: How To Forward Hit Request On 5555 Port To 80 Port
Nov 7, 2011I have one server 172.16.0.100 and i nat this server to a public ip X.X.X.5 and i open RDP for this public ip.Now when i access Remote desktop on this public ip x.x.x.5 it open perfectly.Now my senario is that i want to open a http url on port 5555,server ADMIN open port 80 for this URL on LOCAL lan(http://172.16.0.100:80)So how can i map port 5555 to port 80 on ASA 5520.so when i hit URL [URL]
View 5 Replies View RelatedCisco Firewall :: ASA 8.4 / Translate Port 80 From Outside Connection On Port 85 In LAN Server?
Dec 27, 2011i must translate port 80 from outside connection on port 85 in lan server? how can i configure the asa firewall rules for complete this task?
View 4 Replies View RelatedCisco Firewall :: ASA 5505 / Port 5901 - Alternate Port?
Aug 18, 2011With the Cisco ASA-5505, is there a more secure port that can be configured for VNC other than 5901? I am new to Firewalls We have a User who has requested that 5901 be opened but I was advised not to do so for security concerns.
View 5 Replies View RelatedCisco Firewall :: ASA 5520 - Routed Management Interface On Transparent Firewall?
May 5, 2013I have an asa 5520. How would I configure my dedicated management interface to be able to route off subnet while the firewall is in transparent mode?
View 1 Replies View RelatedCisco WAN :: ASR 1006 Management Port
Sep 13, 2012I saw that the management port for the ASR 1006 has limited routing functionality according to the documentation. I know it "may" not be best practice but can I use this as a routed interface for the WAN port to our Internet or will this not work?
View 2 Replies View RelatedCisco Switches :: SF-300 - Change Web Management Port (from 80)?
Nov 29, 2011I just purchased 2 SF-300 48 port units for 2 customers. I want to be able to remotely manage them over the Internet with my browser. BUT, customer sites already use port 80 for web servers. So, how do I configure this switch to use some other port than 80?
I called support, and much to my surprise he said it cannot be changed. How bizarre that a device with many hundreds of configuration settings does not have one of the most basic settings...
At one customer site I can configure port forwarding and translation to get around this problem, but the other site's router does not offer port translation..
Cisco Firewall :: 5520 - Configuring ASA Management On Sub-interface
Jul 27, 2010I have two ASA 5520 with 4 Giga interfaces and 1 management interface.
I need to use 4 interfaces four data traffic
1- Inside
2- Outside
3- dmz-1
4- dmz-2
The remaining will be the management interface only.How can I configure the Statefull failover and Management?
1- I used the management0/0 for The stateful failover.
2- I used gig 0 for outside
3- I used gig 1 for inside
4- I used gig 2 for dmz-1
5- I divided the gig 3 to two sub interfaces
a- gig0/3.1 for dmz-2
b- gig0/3.2 for Management and I defined it as a management-only
Cisco Wireless :: WLC 5508 Management Port Is Not Pingable
Jul 3, 2012I'm having an issue with the 5508 management port .. I can't seem to ping it from the switch connected to it .. ( the Show cdp command shows that the two can see each other .. but no ping is possible ! [code]
View 4 Replies View RelatedCisco :: Ciscoworks 3.2 RME Compliance Management With 802.1x Port Configuration
Nov 6, 2011i am currently trying to use LMS 3.2 Compliance management to verify and alter our access port configurations for 802.1x. Below is our current configuration
View 1 Replies View RelatedCisco WAN :: Management Port In ROMmon Mode - ASR1002
Jun 4, 2013Is it possible to use the mgmt port when in rommon mode? I use the Mgmt port when IOS is loaded and it works fine. I reboot the router, issue a break to put it in rommon and have set some variables but my Mgmt port never has link and I cannot ping it from the network. In rommon mode it looks like this:
PS1=rommon ! >
MCP_STARTUP_TRACEFLAGS=00000000:00000000
BOOT=bootflash:asr1000rp1-adventerprisek9.03.07.03.S.152-4.S3.bin,1;
IP_ADDRESS=10.71.50.101
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.71.50.3
BSI=0
RANDOM_NUM=1133006948
RET_2_RTS=13:38:27 EDT Wed Jun 5 2013
RET_2_RCALTS=1370453907
?=0
Cisco Switching/Routing :: Management Port On WS4507R
Apr 3, 2012How does the IP address is assigned on management port of WS4507 R, syntax.
View 2 Replies View RelatedCisco Wireless :: 2504 Management Over Separate Port
Sep 25, 2012is it possible to Manage the 2504 Controller over a separate Interface. Exmaple: Port 1 is used as controller management interface (untagged) - AP's are connected to the same VLAN Port 1 is used for Guest Traffic (VLAN 3 tagged) Port 2 should be used to manage the WLAN Controller from the internal LAN. (tested with untagged, tagged, same issue)
with this Setup it is possible to ping the Port 2 IP-Address from the internal LAN but if you try to connect to the controller, the Browser shows "Site not reachable".
I also enabled "Management via Wireless" but without success. I also tried to add the "management" VLAN as tagged on the management Interface with the same effect, the controller is not manageable from the internal LAN. On 5508 WLAN Controller i have an similar setup, but with LAG Port enabled. There this works.
The only interface were i can manage the WLAN controller is from the management Interface.
Cisco Switching/Routing :: Getting 4507R+E FE0 Management Port?
Nov 1, 2012Is there some kind of trick to getting the fastethernet 0 management port to come up? My adjacent switch is up/up, but fe0 is down/down. I dont' see how this could be possible. I am getting all my info remotely, but I am pretty sure it's wired up correctly.
View 2 Replies View Related