Cisco Firewall :: Can The ASA 5520 Do Traffic Shaping Or Policy Map Just Like In A Normal Router

Feb 13, 2011

ASA 5520 can handle 2 ISP? not to load balance or not standby/active but to use the 2 ISP at the same time and separately. for example, ISP_A who has 10m will be dedicated to the customer A/VLAN A, then ISP_B who has 4m will be for the rest of the customer's traffic. Can the ASA 5520 do traffic shaping or policy map just like in a normal router?

View 5 Replies


Cisco Firewall :: Traffic Shaping Per Users / Ip / Application Using ASA 5520

Apr 5, 2011

I hava Cisco ASA 5520 with AIP-SSM module. I would like to have the below features with ASA installed in Transparent mode.
1. Traffic shapping per user
2.  Traffic shapping per IP subnet
3.  Traffic shapping per Application
Is it possible with ASA installed in Transparent mode?

View 9 Replies View Related

Cisco Switching/Routing :: WS-4507R / Policy For Traffic Shaping?

Feb 18, 2012

I am trying to do policy on the interfaces of my switch WS-4507R, below the configuration I used to shap the traffic to 1 Mbps. However, when I tested it the traffic excceded the 1 Mbps.
class-map match-all 1MB
  match access-group name 1MB
policy-map 1MB
  class 1MB


how I can restrict my bandwidth on the interface on 1 Mbps.

View 2 Replies View Related

Cisco Firewall :: ASA5550 - Implement Traffic Shaping / Policing Primarily For P2P Traffic?

Mar 10, 2011

We are looking to implement traffic shaping/policing primarily for P2P traffic. As natively the ASA5550 is only capable of p2p inspection if the traffic is tunneled via port 80 is the AIP-SSM the way forward? We have 2 5550s in active/active failover config. As a side note we are also looking to implement an IDS/IPS system so could this module cover all?Is this module going to provide the desired outcome or is there another module/device out there better suited for this? I would prefer to use the ASA5550s as opposed to implementing another product if only that we can make use of the investment we already made on these devices.

View 1 Replies View Related

Cisco Firewall :: Traffic Shaping ASA 5510 Vs 5505?

Oct 19, 2011

Is there any difference with traffic shaping capability on the 5510 as opposed to the 5505? is there anything the 5510 can do that the 5505 cant? with regards to TShaping?

View 4 Replies View Related

Cisco Firewall :: ASA 5510 Traffic Shaping For Single IP?

Sep 8, 2011

I would like to know if there is a way to apply in the Cisco asa 5510 traffic shaping not for a interface but a single IP address.For example i would like to limit the bandwith for the IP address of my FTP server.

View 4 Replies View Related

Cisco WAN :: Traffic Shaping On Router 2911

Jun 10, 2012

I have following scenario - router 2911 connected to 2950 switches with about 80 vlans. How can I limit speed on each of the 79 vlans (to equal % acros all of them) and give vlan 80 lets say 30% of total bandtwith. Since I am new to QOS, can you point me to the right website or give me example.

View 4 Replies View Related

Cisco WAN :: 3750 ME Traffic Shaping Downstream Traffic

Aug 4, 2011

I am trying to come up with the best way to traffic shape traffic with 3750 Me switches.  the traffic will be coming from a 6504 Sup-7203b downstream and going out the wan.  Core---L3---->6504--intvlan80--trunkport to--->3750Me---g/1/1/1-trunkport to---MetroE network--->int f0/0.80--branch router.  The idea is to use the 3750 to traffic shape the traffic going towards the wan/branch to 500 to match the contracted rate and then to use qos on shaped rate.  I tried to apply it to g1/1/1 using port based policies but it did not shape the traffic.  I changed everything to IP interfaces and it worked.  I need to break up the metroe into different vlans so I can bring branch offices in on different vlans.c

View 3 Replies View Related

Cisco Firewall :: 5520 Re-assign Policy Without Having To Do New Discovery

Sep 27, 2012

I recently upgraded the ios image and the asdm on a cisco 5520 firewall.  I use a policy on a cisco security manager to push policys out to this firewall.  But it cant push to them now because the image has changed on the device.Is their anyway to re - assign the policy without having to do a new discovery.

View 2 Replies View Related

Cisco Firewall :: 5520 - Use Management Port As Normal Port On ASA

Jan 2, 2012

I have got ASA 5520. How to use the management port as a normal port on ASA. What are the basic reqirements for that.

View 3 Replies View Related

Cisco Firewall :: ASA 5520 - Allow Traffic From DMZ To Internet And Block Traffic?

Apr 29, 2012

I have an ASA 5520 with the below config
Gi0/0: outside (Internet)
Gi0/1: inside (Internal users)
Gi0/2: DMZ (web servers, ftp, Mail etc..)
I have a SMTP relay deployed on the DMZ for mailing. I have also a mail servers installed in the internal lan,
I want to allow trafic from dmz to reach internal lan, and i want normally also allow stmp relay from dmz to reach Internet.
How can i block trafic from DMZ to reach Internal Lan (instead of smtp) if the to allow trafic from dmz to internet i must put ANY in the policy?
For allowing trafic from DMZ to reach Internet, the policy must be DMZ -----> ANY ----->Services., this policy means DMZ can implicity reach Internal Lan?

View 2 Replies View Related

Cisco Firewall :: 5520 Why Does Dynamic Policy NAT Rule Apply

Jun 4, 2013

we have a nat exemption rule for to w.x.y.z followed by some static nat rules and then dynamic policy nat rule for to w.x.y.z natting to IP a.b.c.d.When I do a packet trace from to w.x.y.z, it shows the packet first matching against the nat exemption rule, and then immediately afterwards it matches the dynamic policy NAT rule. The static nat rules are being successfully bypassed (which is what I want), but why does the dynamic policy nat rule apply if an exempt rule has been hit already? An actual test between the IPs above reflects the result of the packet tracer as well (IP a.b.c.d is seen on server w.x.y.z).We are running the following software on an ASA5520.

View 7 Replies View Related

Cisco Firewall :: ASA 5520 - Cannot Add Policy To Rule Engine Error

Apr 16, 2013

I have configured the primary firewall every thing seem to be fine, And we have configured fail over device while config is getting replicated to the fail over device we are getting below error.
ERROR: Cannot add policy to rule engine
ERROR: Unable to assign access-list LAN_out to interface inside
IOS and Model are same.But all the config got replicated from primary to secondary but except the one access group command.
access-group LAN_out in interface inside.

View 7 Replies View Related

Cisco Firewall :: ASA 5520 Removed Icmp Inspection From Default Policy-map

May 10, 2012

i have removed the icmp inspection from my default policy-map in my ASA 5520,now i could not able to ping to from my LAN even though i have configured an ICMP Access-list in my asa like ,but I can't ping for testing the Internet connectivity,what shall i do to allow only my self as admin to ping outside?
-icmp permit host echo
-icmp permit host echo-reply

View 1 Replies View Related

Cisco WAN :: Traffic Shaping On 3725 With T1s?

Mar 15, 2011

I am a traffic shaping newcomer and need some guidance as how to BEGIN to approach a problem with traffic. We have been rolling out Windows 7 at sites and the additional traffic it causes on installation is considerable as it has to request information from our  central site to populate My Documents and Outlook mailboxes.This has caused some problems on sites as there traffic rates increase to the point that QoS is not sufficient to protect voice traffic and delays and one-way audio are being experienced.One question is this - is GTS a solution or is CBWFQ within GTS the solution or is something else preferable? The sites involved are data/voice with a variety of routers.Second question is this - if we have a remote site with a 3725 router as the WAN aggregator with one 4506/Sup IV and one Cat 3550-24-PWR the shaping should be best placed on the 3725, correct? Also, are there issues with shaping incoming/outgoing traffic as I seem to have read?FYI, the 3725 router has 12.4(8d) with IP VOICE/NO CRYPTO IOS version. The 4506 has 12.1(23)E4 with basic L3 feature set.

View 1 Replies View Related

3430 Cheapest Way To Add Traffic Shaping?

Jun 19, 2013

What's the good, inexpensive way to add traffic shaping to a small network? Let's say there are about 20 users on a T1 circuit. Existing router is an Adtran 3430 (from the telco so we can't touch it). Everything works fine except when they get really heavy with uploads/downloads when document scanning, and the telnet sessions to the mainframe app start getting dropped. Major PITA. Basically need to make telnet traffic a priority.Now, I could drop a pfSense box in there using an old workstation, but I'd like something I can stick in a rack, or is at least really small and hopefully under $200 or so.

View 7 Replies View Related

Cisco WAN :: 3825 Traffic Shaping And QoS On Multiple EVC

Feb 6, 2011

I have a 3825 with a 1Gb fiber card at one of my sites.  Our ISP and MPLS provider hand off a single gigabit fiber to us that contains 2 50MB EVC's.I need to apply QoS to one of the EVC's and shape them both to 50Mb to avoid upstream rate mismatch bottlenecks.  Both of the EVC's generally only push 10Mb during business hours.When I run UDP stream tests (various rates from 500k-6m that are marked as AF41) to one of my other sites I am consistently getting about 2% packet loss, despite the fact the circuit isn't even close to 50% saturation.  When I remove Shaping and QoS all together, the issue nearly clears itself up, except during peak hours and I get small bursts of packet loss, which is still unacceptable.When the pipe is at near zero utilization (after hours) there also is no packet loss with or with out the shaping/qos applied.

View 1 Replies View Related

Cisco Infrastructure :: 185 / Traffic-shaping On The LAN Interface?

May 5, 2011

There is a remote server that downloads info from a server here at HQ. When the dowloads start the rxload on the S0/0/0 interface jumps to 98 percent or so; rxload 250/255. I needed to limit the bandwidth utilization between the servers, so I added the below line to the LAN interface on the remote router.By adding the command, it reduced the download utilization -which is what I wanted.
access-list 185 permit ip host any
int f0/0
traffic-shape group 185 10000 8000 8000 1000
Question:How would applying this to the LAN interface cause the download utilization (Coming from s0/0/0) to decrease?

View 4 Replies View Related

Cisco WAN :: ASR1001 / Traffic Policing And Shaping

Feb 25, 2012

I want to take 100Mb incoming from a service provider and police it off into several VRFs for customers.One of these VRFs will be 30M.I further need to traffic shape this (30Mb) out to 40 x 0.75Mbps (burstable to 30M) customers.
I am using an ASR1001.

View 2 Replies View Related

Cisco WAN :: 3800 / Traffic Shaping When QoS / CoS Employed?

Nov 19, 2011

I have a client who has Cisco 3800 series routers in their data centre with which they have QoS/CoS policies implemented. They wish to further manage traffic by limiting outbound traffic to their branch sites in line with the network access bandwidth each site has available. Is this possible whilst leaving the QoS policies in place? If so how?

View 1 Replies View Related

Cisco WAN :: 3845 - Traffic Shaping For Bandwidth Management

Jun 1, 2011

I am trying to get ride of an old traffic management appliance and would like to replace it by a simple Cisco 3845.
The configuration is really simple:
Customers -- Router 3845 -- Internet
I want to be able to provide bundles to customer such 64kps garanteed/ 2mbps MIR (retail) and 2mbps garanteed no MIR (business).
I need also to specify to the router the total internet bandwitdh available (example: 20mbps symetrical).
This configuration will work ? Should I worry about any performance issue if I start to have a lot of customers ?
ip access-list extended Cust1
permit ip any sub_Cust1
permit ip subCust1 any

View 2 Replies View Related

Cisco WAN :: Is Traffic Shaping Supported On ASR1001 Ge Subinterface

Feb 26, 2013

I am suggesting an ASR1001 as a head end router for a small hub spoke WAN consisting of 4 branch sites connecting to the head via LES. 3 are 100mb, one is 30 mb. I will be connecting the LES circuits to a swithc and then trunking to the router. I would like to apply outbound  shaping to these 4 subinterfaces on the router, and just want to check this is supported?

View 1 Replies View Related

Cisco WAN :: 3750 / 6509 - Traffic Shaping VRFs WAN Bandwidth?

Jul 14, 2011

We are a new medical school located in PA. Just have just completed a new building and are now working on getting our network finished. Here is the situation we have a 50MB Internet Connection that comes into our network that then hits the ISPs Cisco 3750 which sends it to two of our Cisco 3750s for redundancy. From the 3750 goes into our Cisco 6509 with a FWSM module, then out from there to our distribution switches which are all Cisco 2960s.
What we would like to do is to control how much WAN connectivity each of our VRFs get. Right now we have a Faculty, Student, and Research VRF formed, and are trying to figure out the best spot where we can say Faculty gets 30MB of Bandwidth, Students gets 10, and Research gets 10. If possible would like burst capabilities.

View 3 Replies View Related

Cisco Firewall :: ASA 5520 - VPN Traffic Is Getting Dropped Through Firewall

Apr 8, 2011

Our Local Network is behind the CISCO ASA Firewall.Whenever we are accessing to Client VPN server,it is getting connected but after few Minutes (May be 5/10/30 Min),the sessions are terminating. The same traffic through PIX is no issue , only with ASA Firewall. See the following Error and request you give the possible root cause for this.
2011-04-09 16:15:09    Local4.Info    %ASA-6-302016: Tear down UDP connection 87447908 for OUTSIDE: to inside: duration 0:27:49 bytes 18653

View 1 Replies View Related

Cisco Switching/Routing :: 6513 - Rate Limit And Traffic Shaping?

Mar 21, 2012

I am looking for step-by-step configuration on how to enable rate-limit and traffic shaping on Cisco 6513 vlan interfaces.  I am not able to find this particular document on CCO.

View 3 Replies View Related

Cisco WAN :: C7200-IK9SU2-M / QoS Traffic Shaping Not Working (but Policing Does Work)

Feb 8, 2011

I have lots of PPPoE users that get Virtual Access interfaces created upon login based on a virtual template. I need to traffic shape them. I know how to get it to work on an individual basis, because the policing within a service policy works fine. As soon as i change it to shaping it leaves things wide open.I really dont care how it gets done, I just need to be able to specify a speed to be traffic shaped and apply that to a virtual template. I need to limit speeds on the download and upload, i understand that the upload i will use the policing, but the download i need it to smooth out the flow and be traffic shaped, not policed.
Here is my Policies and classes:

policy-map CHILD class class-default  bandwidth 1650policy-map PARENT class class-default  shape average 1650000  service-policy CHILD****
Here is my Virtual Template:
interface Virtual-Template8 description pppoe-auth-FTTH ip unnumbered FastEthernet0/0 ip access-group subs-in-FTTH in ip mtu 1493 timeout absolute 6120 0 peer default ip address pool FTTH-POOL ppp authentication pap pppoe-auth ppp authorization pppoe-auth ppp timeout idle 84600 service-policy output PARENT

The results i am getting is unrestrcited throughput, i am seeing about 40mb of throughput when the target is to limit to 1.65MB. As you can see from the output the PARENT class is seeing 279116 packets, but the shaper only saw 59. In all the examples i see on the internet these two numbers should be the same. Why is the shaper not acting on all the traffic crossing that class/policy?
Cisco IOS Software, 7200 Software (C7200-IK9SU2-M), Version 12.4(12), RELEASE SOFTWARE (fc1)

View 11 Replies View Related

Cisco WAN :: 1921 Traffic Shaping Feature Is Not Supported In User Defined Class

Oct 29, 2011

I make qos on VPN Tunnel, but i make command service-policy output name, it show the error below Traffic Shaping feature is not supported in user defined class of parent level policy.My cisco router 1921, IOS : c1900-universalk9-mz.SPA.150-1.M5.bin

View 1 Replies View Related

Cisco Firewall :: ASA 5520 VPN Tunnel Up But Not Traffic

Nov 1, 2012

We just migrated from a single 5510 to a dual (failover)  5520, It seems that everything is working except the remote VPN. We can establish a tunnel and authenticate as local users, (going to LDAP when all is working) but no traffic is passing. I know I am overlooking something but cant see it. [code]

View 12 Replies View Related

Cisco Firewall :: 5520 VPN Traffic Between Interfaces

Jun 12, 2011

Our ASA 5520 firewall is running 8.0(4) IOS.I have an internal L2L VPN terminating on my firewall (from an internal remote site) on ENG interface.With the default "sysopt connection permit-vpn" command enabled, VPN traffic is allowed to bypass the ENG interface acl.The security level on the ENG interface is set at 50.The security level on the destination interface PRODUCTION is set at 40.Inbound VPN traffic bypasses ENG interface acl and since higher-to-lower security level allows VPN traffic to flow freely from ENG to PRODUCTION, it seems the only place to check/filter VPN traffic is an ACL placed on the PRODCTTION interface and set at INBOUND (outbound VPN traffic).

View 4 Replies View Related

Cisco Firewall :: Traffic Prioritization On ASA 5520?

Dec 1, 2011

I have a Cisco ASA 5520 (8.0) and I'm trying to figure out how to prioritize traffic to specific websites (by either domain names or IP addresses/ranges).  This document [URL] has some great examples, but I'm not able to create a class-map that will match addresses.  I'm not doing any other traffic manipulation on this ASA. 

View 1 Replies View Related

Cisco Firewall :: ASA 5520 - Allow Traffic Between DMZ Servers?

Dec 20, 2011

We can´t reach DMZ servers from other DMZ servers?If I make a ping from DMZ server to another, sometimes only recieve one ping, sometimes 4, sometimes 0.How can I allow the traffic between DMZ servers??
(ASA 5520 Version 8.4)

View 2 Replies View Related

Cisco Firewall :: 5520 - Traffic From Inside To Outside

Mar 2, 2011

I am setting up a pair of 5520 in A/S mode but the traffic from inside to outside seems blocked somehow.

asa01# sh run : Saved
ASA Version 8.3(1)
host name asa01
enable password LFJ8dTG1HExu/pWQ encrypted
password 2KFQnbNIdI.2KYOU encrypted

Base on the above configuration, I still cannot ping or HTTP.

View 10 Replies View Related

Cisco Switching/Routing :: How To Setup Traffic Shaping On 4500X Outbound Port To WAN Routers

Mar 26, 2013

We have some ASR WAN routers which have a dedicated 400M interface to a remote site.
Servers on our Local network source the data through some firewalls via 10G interfaces, which connects to 4500X WAN switches then to the Routers on 1G links.
The sources are rate limiting the traffic but the routers are periodically dropping packets which I think is mostly due to burstiness in the traffic between as it traverses through from 10G links to 1G then to 400M. 
How to setup traffic shaping on the 4500X outbound port to our WAN routers.I'd like to see if we could buffer and smoothe out the traffic as it exits the 4500X WAN switch 1G port to the WAN Routers.

View 1 Replies View Related

Copyrights 2005-15, All rights reserved