I just bought a Cisco ASA5505. I'm trying to opening a port range through CLI, but it doesn't seem to be working.
Background:I have an FTP Server running behind the firewall and need to allow port ranges 30000-30100 for data connections. I have been using FTP through the command prompt and its working. However, I cannot use it through the FileZilla client as it fails to query the directories. I have the ASA forwarding to port 1125 from 21 in passive mode.
Access-List:
access-list Outside_Access_In line 3 extended permit tcp any any eq ftp-data (hitcnt=0) 0xfa8ed43d
access-list Outside_Access_In line 4 extended permit tcp any any eq ftp (hitcnt=17)
I have an ASA 5505 on a job. It is a smaller business that would have done better with an RV082, but they have what they have. It is running firmware 8.4. The client needed ports forwarded for their FTP server. The port range in this config is tcp 43333-43339. The FTP server ip is 192.168.1.2. [Code] ......
I have a LAN with Cisco 1941 as the only router with NAT that connects it to the internet, with a single public IP. There are many gamer users, and they complain that Call of Duty Modern Warfare 2 sees our network as "strict NAT", while for full gaming experience it needs "open NAT". After a small research I have found out that CoD needs certain port ranges to be forwarded to LAN IPs. Well, I know how to forward a range of ports to a single IP, but how is it possible to forward a port range for all the IPs in the LAN?
my friend was against a wall trying to update her office's system, and it seems like every Cisco person in the region has gone on vacation.For some sort of new system her office is getting, she was told that she needed to enable NAT with external IP xxx.xxx.xxx.14 (The ASA's IP is xxx.xxx.xxx.11) and internal IP xxx.xxx.xxx.58 and that port 8222 needs to be open. I know this is sort of vague, but it's what she was given, and I know the 8222 port is very specific in function,?
At any rate, the best I could come up with was to run:
But after I inserted this, she did what she was supposed to be able to do (went home and tried to run some sort of remote installation file) and it didn't work...
I need to open port range 554 - 558 to a DVR on the internal network. Also, I need to NAT one of my public IP's to the DVR. How is this accomplished in 8.4? I was able to do it in an older version ASA software.
I have a network with multiple servers behind a PIX with 6.3 on it. I have one public IP address, and I'm using NAT. I'm currently trying to port my Exchange server to a cloud host, and the vendor is requiring I open up a wide range of ports for MAPI, basically ports 1024 on. What would be the command to forward all of the trafic cominto/from that broad range? if I could simply route all trafic to and from their two IP addresses to my email server, that would accomplish the same end goal.
: Saved : Written by enable_15 at 03:51:29.049 UTC Mon Feb 4 2013 ASA Version 8.4(4)1 host name cisco asa enable password xxxxx encrypted password xxxxx encrypted names interface Ethernet0/0 switch port access v lan 100 interface Ethernet0/1 interface Ethernet0/2 [code]...
I have a Windows 2003 server running a L2TP VPN server on it. I'm putting theASA5505 in replacement of an open source firewall.
My question is that, I can't seem to forward the ports correctly for L2TP to the internal address of the 2k3 VPN server. It seems to me that the ASA is trying to negotiate the VPN connection rather than forward it internally.
Cisco ASA5505 WAN 216.136.1.2 LAN 10.1.1.1/24 Windows server - 10.1.1.14
I'm not able to access my Slingbox from the outside. I've set up port forwarding on port 5001 to allow outside connections in, but port forwarding isn't working. Am I missing something?
I need to NAT a port range spanning from TCP and UDP 50,000 to 59,999 from inside global address 58.96.x.x on loopback2 to an inside local address of 192.168.5.5.Currently all the existing NAT translations are 1-to-1 that map inside global addresses on a wide span of Loopbacks and a Dialer Interface to inside local addresses on few subnets which are fine.I'm using an 1811 with an ADVIPSERVICESK9-M image, version 12.4(6)TS
I am at a loss on configuring a new ASA5505 for multiple static port translations.I would have expected to simply add several service command to a network object to complete the task, however, the service command overrides the previous and replaces rather than adds to the translations. [code] However, if entered in that order the 8443 overwrites the 8080 static translation.What is the correct procedure to establish multiple translations? If someone could also provide the "old" style for pre 8.2 release, I'd like to compare because I thought I used to do this with an access-list somewhere.
I've had a Cisco ASA 5505 firewall connected to a cable modem (Virgin Media, UK) for the past 3 years. In the last 6 months or so I have noticed that the ASA would drop the outside (internet) connection intermittently, usually at least once every 1-2 weeks - the interface still shows as being up but no traffic crosses it, and computers on the inside network abruptly lose internet connectivity. Rebooting the ASA or administratively shutting down the interface and bringing it back up again would cure the problem straight away until the next time it happens.
In the last couple of days however despite nothing having been changed in the configuration the frequency of this connection drop has increased to the point where I would lose access to the internet within an hour of rebooting the ASA. It does not seem to matter whether or not there is traffic currently going out or not, inside computers just appear to suddenly lose internet connectivity.
I have tried the following without success:
1) I completely wiped the configuration (configure factory-default)
2) I changed the port the cable modem was connected to (eth0/0 -> eth0/7, changing switchport vlan accordingly)
I thought perhaps 2) had fixed it but it lasted a whole 2 hours before I woke up this morning to find that none of the internal equipment had internet access despite the fact eth0/7 was showing as up/up in ASA CLI.
This morning I manually set the eth0/7 port to "speed 10" (10Mbps, full duplex). It was previously set to be auto-negotiation (default) on both speed and duplex. As of this post it has managed to keep the outside connection up for 3 hours - but I'm not optimistic that it is fixed.
Interface counters have never shown any collisions, errors, etc - only packets input and output as expected.
Since the problem persisted across ports (eth0/0 -> eth0/7) I'm wondering whether or not the problem could either be faulty memory, or some kind of speed/duplex incompatibility between the cable modem and ASA.
How to configure this setup.I have an ASA5505 with dual wan failover, FiOS (eth0) & Cable (eth1). how to configure the port forwarding for all my devices so it doesn't matter what external interface the traffic is coming from. For example, I need web traffic on port 80 forwarded to 192.168.1.150 regardless of whether it is coming through eth0 or eth1.
I have installed ASA5505 in the network. Port forwarding has been done for one of the server in our LAN. Public users are able to access the server successfully. I am trying to access from inside using the same Public server IP, but unable to access it. Can I have this feature in ASA5505(I think it is loopback configuration). If so, may I know the configuration detail?
I am a total Cisco novice who has just had a ASA5505 installed to replace a linux freeware firewall (smoothwall).I'm told that the 5505 can't port forward traffic (e.g. ssh) from two external IP addresses to two internal destination machines via the same port # (22 in this example).
I thought I had the configuration to allow bi-directional traffic for my Blackberry server. I have a second fw with the same config and it worked on that one. But right now, my blackberry server is down, and all the users are upset.
configuring the ASA particulary after the change to how NAT is implemented. What I am trying to accomplish logically seems fairly simple, yet I cannot get it to work. I have a Synology NAS at home that I am trying to reach via the internet. Prior to using my ASA, I had Verizon's FIOS router as my gateway and everything forwarded with no issues. The ports I need forwarded or reachable via the internet are TCP port 80 and 5000.I can also configure it via command line if that's the easier/preferred method.
I'm new to an ASA 5510 running 8.4(3) and am trying to figure out something regarding time ranges in ASDM. I simply want to allow a single port during business hours only (I'm not concerned about open sessions needing to be closed). So as an example I add a rule something like:
(RULE1 on the internal interface) SRC=INTERNAL DEST=ANY SERVICE=RDP ACTION=PERMIT with a time range set for weekdays 8:00-16:59. I did a test after 5pm on a weekday and was still allowed to do RDP to a server (from INTERNAL), and after using the packet trace tool saw it was still passing through due to a rule a couple lines down (rule 4) that allowed a port range that happened to include port 3389. So my question is if I specify an "allowed" time range and someone attempts access outside that time range, why doesn't it drop it right there? I guess I'm assuming that anything outside the "allowed" time range would be dropped but that doesn't seem to be the case. I'm also assuming the rule base is processed top to bottom.
ASA 5505 Firmware 8.3(4), ADSM 6.4(2).I have a public IP address of 168.87.3.4.I need to forward ports (5060, 5080, etc.) to one internal address. (192168.1.1).I need to foward different ports (10020-10080) to a different internal address (192.168.1.2) Everything I read tells me how to do this in a 1 to 1 static NAT.
I want to open a certain port on my router and I know it shouldn�t be a problem, just go inside of your router settings and add the port manually. But somehow I was enough smart to forget my routers username and password, now my question is my only option a hard reset of the router and deleting all the work I put in to connecting the two computers with my router (believe me I had my share of troubles connecting them with the router) or is there a way to open the port on the router from my computer without accessing my router settings.
I have a DSL modem (custom made and branded by my ISP) which is receiving a DSL stream... it has an external IP which is visible to the world, say, 11.22.33.44 ... This modem has DHCP enabled, has an internal IP for itself, which is 192.168.1.1 .. it is connected to 2 laptops via and ethernet cable .. Laptop 1 has IP 192.168.1.2, and Laptop 2 has IP 192.168.1.3 ...On Laptop 1, two applications are running, jDownloader and Media Player Classic, which have their web interfaces on ports 8765 and 13579,respectively.. I can access both of these web interfaces from Laptop 2 by opening these addresses: 192.1681.2:8765 and 192.168.1.2:13579 ... both of their web interfaces open up, meaning the web interfaces are working fine ..Moving on, I now want to access these web interfaces from outside my network as well, and so I've configured port forwarding in my DSL modem to forward all traffic on ports between 8000 and 14000 (both TCP and UDP) to IP 192.168.1.2 ... I have verified that port forwarding is working by testing it using PortForward.com's port checker tool, and this website too: Open Port Check Tool - Test Port Forwarding on Your Router When I use the website, if I'm running the applications on Laptop 2, the website reports that the port is open .. if I then close the application, the website reports the port is closed ... This makes sense as nothing is listening on my machine in the latter case .. Also, if I disable port forwarding in my modem, again, the website reports the port is closed ... so, the website's results seem to be okay ...
Despite the above tools reporting that port forwarding is working, I am unable to open the web interfaces from outside my network ... So for example, if I tried to browse 11.22.33.44:8765 or 11.22.33.44:13579, nothing opens in my browser ... But if I accessed these web server's locally from Laptop 3, by typing in 192.168.1.2:8765 or 192.168.1.2:13579, they opened ... The tools report unanimously that port forwarding is working, and yet I am unable to open the web interfaces from outside the network ..Also note that I have disabled the firewall from my computer, and have also made sure that any option in the above programs (whose web interfaces I am trying to open) that says only local connections are to be accepted, is disabled ...
I am having some problem with fowarding some ports. Everytime I try to open a port, specifically 27015 it wont open. I go onto canyouseeme.com and it says there is no route to host. I have a Westell A90-750015-07. All of my firewalls are also turned off.
So I am working on a website with MySQL/PHP that I have been developing on my Linux box. I wanted to show a friend my progress so I temporarily opened up port 80. So he was able to just type in my public IP and it brought him to my localhost index.
My question is, when I type in my IP address in the URL bar, does the web browser automatically just assume port 80? What happens if I want to have 2 different servers from the same local network and one is running through port 80 and the other is running through port 90? In this case, would I have to type ":90" to access the machine running on port 90?
I have a cable modem hooked up to a Linksys WRT54G2 wireless router, which is hardwired to the computer I use.
I go into the router's menu by going through the standard 192.168.1.1 in the browser, and then go to Applications and Gaming. The port I am trying to open is port 25565 for both TCP and UDP. In the Start and End ports I put 25565, and for the end of the IP Address, I put the last digits of my IPv4 address (10). I used a couple of port checker tools, and it is reporting as still being closed.
We have a DVR here at work that has a web interface on port 100. From our internal network we just use http:192.168.100.40:100. What is the best way to set that up on cisco 5510 firewall. I have cisco asdm and set a access rule: enabled=checked ; source=any ; destination= 192.168.100.40 ; service= tcp 100 ; action=permit. It shows a couple of hits when I go to [URL]
I'm having an issue on my Pix 501- ver. 6.3(5) firewall when host 192.168.1.2 accessing any website, no website is opening and when i issue command sh xlate so don't see anything and i think i must enable natting on this firewall as same as on ASA nat-control
I am trying to configure a new 5505 but I am having difficulties opening ports that allow traffic in from the outside. My setup is Comcast Business Modem (w/ single static IP) -> ASA (10.0.0.1) -> (dumb) Switch -> NAS (10.0.0.10). I am attemping to open port 5001 to the NAS. I am very new to IOS so I have mostly been working in ASDM. Not sure if I am overcomplicating this for myself or what but I am stuck.
My running config is -
ASA Version 8.2(5) ! hostname ciscoasa enable password 8Ry2YjIyt7RRXU24 encrypted
