How to configure this setup.I have an ASA5505 with dual wan failover, FiOS (eth0) & Cable (eth1). how to configure the port forwarding for all my devices so it doesn't matter what external interface the traffic is coming from. For example, I need web traffic on port 80 forwarded to 192.168.1.150 regardless of whether it is coming through eth0 or eth1.
View 2 RepliesASA 5505 Firmware 8.3(4), ADSM 6.4(2).I have a public IP address of 168.87.3.4.I need to forward ports (5060, 5080, etc.) to one internal address. (192168.1.1).I need to foward different ports (10020-10080) to a different internal address (192.168.1.2) Everything I read tells me how to do this in a 1 to 1 static NAT.
View 1 Replies View RelatedI have a Windows 2003 server running a L2TP VPN server on it. I'm putting theASA5505 in replacement of an open source firewall.
My question is that, I can't seem to forward the ports correctly for L2TP to the internal address of the 2k3 VPN server. It seems to me that the ASA is trying to negotiate the VPN connection rather than forward it internally.
Cisco ASA5505
WAN 216.136.1.2
LAN 10.1.1.1/24
Windows server - 10.1.1.14
I've added the NAT and ACL and still nothing.
I'm not able to access my Slingbox from the outside. I've set up port forwarding on port 5001 to allow outside connections in, but port forwarding isn't working. Am I missing something?
object network INSIDE-HOSTS
subnet 10.10.10.0 255.255.255.0
object network Slingbox
host 10.10.10.254
object-group protocol TCPUDP
[code].....
I have an ASA 5505 on a job. It is a smaller business that would have done better with an RV082, but they have what they have. It is running firmware 8.4. The client needed ports forwarded for their FTP server. The port range in this config is tcp 43333-43339. The FTP server ip is 192.168.1.2. [Code] ......
View 8 Replies View RelatedI have installed ASA5505 in the network. Port forwarding has been done for one of the server in our LAN. Public users are able to access the server successfully. I am trying to access from inside using the same Public server IP, but unable to access it. Can I have this feature in ASA5505(I think it is loopback configuration). If so, may I know the configuration detail?
View 4 Replies View Relatedconfiguring the ASA particulary after the change to how NAT is implemented. What I am trying to accomplish logically seems fairly simple, yet I cannot get it to work. I have a Synology NAS at home that I am trying to reach via the internet. Prior to using my ASA, I had Verizon's FIOS router as my gateway and everything forwarded with no issues. The ports I need forwarded or reachable via the internet are TCP port 80 and 5000.I can also configure it via command line if that's the easier/preferred method.
View 11 Replies View RelatedI have ASA 5505 with 8.4(2)8 software for one of my branch offices and I can't configure port forwarding.It seems to be very simple, but it's not working. I use my ASA as a gateway to the internet for users in office and for site-to-site IPSec VPN to HQ. I have pppoe-enabled outside interface, but ISP gives me static routable ip address. I have server behind my firewall and I should "publish" to the WAN some of its' tcp and udp ports, but I see that no packets forwarded through ASA. I tried to configure PAT as stated in official "Cisco Security Appliance Configuration Guide" through CLI and ASDM.[code]
View 4 Replies View RelatedI have the following setup:
ADSL ---> Cisco 877 with connected site-to-site VPN's ---> Cisco ASA 5505 with Remote VPN enabled
I want to connect my Android phone to the Cisco ASA 5505 with Remote VPN. When I forward port 500 and 4500 on the Cisco 877 to the Cisco ASA5505 I can connect with the phone.
But as expected, the site to site connections are lost because now they try to reach the ASA 5505 also.
I want to exclude the site to site external IP addresses from doing static NAT to the ASA 5505...how can I accomplish this ?
To configure DSL port forwarding,I want to configure as remote desktop.
View 3 Replies View RelatedI need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit . Any step by step command.
View 9 Replies View RelatedI have a Cisco SG300-20. I have read the documentation and cannot seem to locate the instructions for port forwarding. I need to forward TCP port 8088 to IP address 192.168.14.110 on the switch.
View 5 Replies View RelatedI need to configure the port forwarding on Cisco 887 to forward port 22 on Public IP to a LAN IP port 2200. I don't know anything on Cisco router at all, beside telnet to the cisco and quit.
View 1 Replies View RelatedCan this scenario be done one the cisco 877 router? I have VPN Ipsec up and runing on both site. How can to configure the port forwarding to the remote server over the tunnel? url...
View 16 Replies View RelatedI have tried replacing a loaner RV082 V2 with an RV042 V3 router with firmware 4.0.4.02. All worked well, including the site to site VPN. However, in spite of the fact that I have ports 443 and 4125 forwarded to the server (192.168.2.10), we are unable to connect via RWW. There is no such problem with the RV082. What is different with the way we configure these V3 routers for port forwarding?
View 2 Replies View RelatedSo here is my network.
ASA5505--->Cisco1841--->Cat2960
Code
ASA asa831-k8.bin
Cisco 1841 c1841-adventerprisek9-mz.151-4.M2.bin
Cat 2960 c2960-lanbasek9-mz.122-55.SE1.bin
and here is my dilemma.
I can SSH from the internet to my ASA on default port 22, directly to my public IP. I can SSH from the internet to my Cisco 1841 on port 2001. I can not however, SSH to my Cat 2960. From what i can tell, on the Cat2960 i can't change the default port 22 for SSH to different port, just like i did on the Cisco 1841. I looked to see if I can change the default port for SSH on he ASA, it does not look like this is an option.
The bottom line is that i want to be able to SSH to all three devices from the internet. I only have one public IP. As of now, what i can do is only SSH to the ASA on default port 22 directly to the public IP and Cisco 1841 on port 2001. It appears that changing the default SSH port on Cat 2960 is not an option. It also appears that I can't change the default SSH port on the ASA, if i could, i would and then i should be able to SSH to the Cat 2960 on port 22. No matter what i did on the ASA, it always listens on port 22 for SSH connections.
show asp table socket
TCP 001f549f <<pub IP>>:22 0.0.0.0:* LISTEN
how do i make it listen on different port?
Here is relevent config for SSH for cisco 1841 (port forwarding)
ON ASA
object network ROUTER
host 10.10.1.1
[Code].....
I have a asa 5505 Sec plus with 3vlan, inside, outside and dmz.
On the outside i have 5 ip's for my use, and in the dmz i have a webserver that need to communicate with one sql server on the inside.
The "sql" also needs to be accessible from outside and thus has a static nat with a dynamic nat so it replies from same ip as on nat ie 72.72.72.5 webserver is natted with 72.72.72.6
sql inside ip is 192.168.1.2, gw 192.168.1.1
webserver ip is 192.168.2.100 gw 192.168.2.1
sec lvl on inside is 100 and on dmz 50
with a dynamic policy running inside-net/24 to dmz-network/24 translagt to dmz 192.168.2.2 i can get it to ping 1 way from inside to dmz, but not the other way around...
All i need is to open 1 port ie 6677 both ways for this communication to work.
I'm not very familiar with the CLI and do most stuf in GUI (know i should learn CLI, but time doesnt let me)...
on access rules i have just added everything from any to any using , ip, icmp, tcp and udp just to be sure... :-)
I am trying to open up port 32400 on my 881w Cisco router but I have not had any success I need to configure manual port-forward to enable my Plex Media server.
View 1 Replies View RelatedWhen using the connect to the internet wizard in SBS 2008 (CTIW) the server comes back with an error that it cannot communicate with the router.Are there any settings that need to be configured in the ASA 5505 to allow communications with SBS 2008 using Exchange Server 2007? I am using ASDM 5.2 at this time.
View 3 Replies View RelatedIs it possible to configure bridge mode in asa 5505 if it is can u provide me a config.
View 1 Replies View RelatedI just started at a new company and they want to use iphones in place of blackberry's, what a surprise. We have a exchange server and blackberry enterprise server. My question is how do I configure the cisco ASA to allow for iphone vpn connection and start replacing our blackberry's.
View 1 Replies View RelatedI have an ASA 5505 running 8.4.4.1. I've configured three WAN interfaces and have assigned failover on one of them (we have two ISP's, and a total of 3 static IP's in 3 different subnets). I've noticed that all the traffic is flowing through only one of the three interfaces, but I need to allow incoming https traffic on the second WAN port so I can access our Exchange server (we already use https on the first WAN port to access another server).
[code] WAN1 is the default outgoing route and we've configured several incoming services on it (smtp and https for example) and appears to be working properly as mail is coming and going and users can access the RDS gateway.I need to configure WAN2 to accept https traffic and send it to our Exchange server to enable OWA (webmail) access.I've configured the same Access and NAT rules on all three WAN interfaces for smtp (but I suspect only the first one is currently functioning at this point, I'll test it next chance I get). I thought all I'd have to do is configure an access and NAT entry on WAN2 (same as on WAN1), but direct the traffic to the OWA server instead of the rds gateway server, but it is not working.
In the realtime log I can see that it appears to be receiving the traffic on the WAN2 IP, but seems to be passing this through to the inside via the WAN1 interface.
I have interfaces defined on the 5505:
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
[Code].....
I only need one interface to connect to a single host on the inside (VLAN1) and then connect E0 to a DSL.
Is it possible (are what are the commands required) to take one of the other interfaces and create a Management port on the local office LAN?
I have a few devices that the manufacturer told us we have to set with a public IP (No Natting) We have Internet ->ASA5510-> Switch 3550 with 3 vlans. Up to now we have always use Natting to configure internet access to specific devices. I heard setting up a witch with one VLAN connected to the internet and all other internals is a bad idea. that was the only Idea we had.
View 3 Replies View RelatedI have a cisco 5520 with 8.4.4(1) and I already have a NAT for an email server on it.Here is the IP and ports on current configuration:
Email Server Private IP: 1.1.1.1
Email Server Public IP: 2.2.2.2
Email Server Local Ports : 25, 587
Right now I have ports 25 and 587 opened for 2.2.2.2 so, now I need to add a port redirection for another port:
New Port : 8925
I need to redirect 2.2.2.2:8925 to 1.1.1.1:587
i'm having a problem portforwarding/redirection for the pix 501?I'm trying to open the ports 49003 and 40085 in order to view our dvr remotely and i'm not exactly sure how to it.
View 11 Replies View RelatedI have an issue with portforwarding in my teleeye cctv behind asa 8.4. I can browse the DVR outside via http however when i attempt to login, "server busy" will prompt afterwards. Note: Theres no issue when acesssing the DVR locally.
Heres my config.
OUTSIDE INTERFACE:
interface Ethernet0/3
speed 100
duplex full
[Code]...
I just bought a Cisco ASA5505. I'm trying to opening a port range through CLI, but it doesn't seem to be working.
Background:I have an FTP Server running behind the firewall and need to allow port ranges 30000-30100 for data connections. I have been using FTP through the command prompt and its working. However, I cannot use it through the FileZilla client as it fails to query the directories. I have the ASA forwarding to port 1125 from 21 in passive mode.
Access-List:
access-list Outside_Access_In line 3 extended permit tcp any any eq ftp-data (hitcnt=0) 0xfa8ed43d
access-list Outside_Access_In line 4 extended permit tcp any any eq ftp (hitcnt=17)
[Code].....
i have a asa with a outside IP address of 140.32.121.5. behind this firewall i have a cisco MWR 2941 that i would like to connect to via telnet. its inside ip address is 10.10.10.2. my reasoning for this is because i cannot SSH or telnet from a ASA so i need to have the ASA push my telnet request to the router on its inside interface.i have tried some NAT examples but i am very green with NAT. i have also built access lists that look like the follow " access-list 101 permit tcp any 10.10.50.2 eq 23. and then tied the access-group 101 with the outside interface. this also with no success.
View 1 Replies View RelatedI need to open port range 554 - 558 to a DVR on the internal network. Also, I need to NAT one of my public IP's to the DVR. How is this accomplished in 8.4? I was able to do it in an older version ASA software.
View 3 Replies View RelatedI've tried setting up some simple port forwarding on my ASA, where I want to forward one port on the external interface for both UDP and TCP to the same port on an internal server.
It works fine for UDP, but all TCP packets are dropped on the outside interface, even though the configuration for UDP and TCP is basically the same! This is my config:
object network MY_SERVER
host 10.10.1.4
object service TCP_MY_SERVICE
[Code].....
Port count goes up on line 2 (UDP) but never for line 1. I just see the packet denied instead. Same thing happens in the packet tracer, a packet destined for my external interface on that port for UDP is allowed and NAT'd just fine. TCP it gets dropped by the ACL on the outside interface.
I have a Cisco ASA 5510 appliance running ASDM 6.3 We have a number of public IP addresses associated with our company. In order to utilise the IP addresses effectively I want to use one puplic IP address for two servers running on different ports.e.g.
Public IP address 78.109.174.100
for both
Server 1 HTTPS and HTTP
Server 2 FTP
Both Servers live in the same subnet (DMZ) I believe this maybe port forwarding but could be completely wrong. I've tried creating a NAT rule that goes from Server 2 Network object to Server 1 external but this didn't work.
have a couple of ASA 5505's which work fine for what they are doing VPN and all that - we have 1 DLINK DFR-700 Firewall left and I need to get a new ASA to replace this since it is old.All this box really does is port forward external clients to 1 address on the internal lan for client software updates.So lets say we have client a with IP 1.1.1.1 and client b has 2.2.2.2 - at the moment this is what happens client a and b come in through http and get mapped to the internal http server 10.10.1.2So I need to setup about 100 clients which can come in through http only - get mapped to the internal IP and also keeping the internal server to be able to access anything outside.
View 16 Replies View Related