I just started at a new company and they want to use iphones in place of blackberry's, what a surprise. We have a exchange server and blackberry enterprise server. My question is how do I configure the cisco ASA to allow for iphone vpn connection and start replacing our blackberry's.
View 1 RepliesI have a asa 5505 Sec plus with 3vlan, inside, outside and dmz.
On the outside i have 5 ip's for my use, and in the dmz i have a webserver that need to communicate with one sql server on the inside.
The "sql" also needs to be accessible from outside and thus has a static nat with a dynamic nat so it replies from same ip as on nat ie 72.72.72.5 webserver is natted with 72.72.72.6
sql inside ip is 192.168.1.2, gw 192.168.1.1
webserver ip is 192.168.2.100 gw 192.168.2.1
sec lvl on inside is 100 and on dmz 50
with a dynamic policy running inside-net/24 to dmz-network/24 translagt to dmz 192.168.2.2 i can get it to ping 1 way from inside to dmz, but not the other way around...
All i need is to open 1 port ie 6677 both ways for this communication to work.
I'm not very familiar with the CLI and do most stuf in GUI (know i should learn CLI, but time doesnt let me)...
on access rules i have just added everything from any to any using , ip, icmp, tcp and udp just to be sure... :-)
I have configured a Cisco ASA 5505 to allow VPN access from outside to my LAN using Cisco VPN Client software. The connection is establishing properly with the ip address from my VPNPool. From outside (on VPN connection) I can ping the interface e0/0 (outside) and the interface e0/1 (inside) of the firewall, but I cannot ping the layer 3 switch interface to which the ASA is connected ( int gi1/0/22 ip address 192.168.1.2/30 ) and I cannot ping any vlan interfaces inside my switch. Therefore, I cannot connect to any server on my internal LAN. I am available at any time if further information is needed. find attached my ASA config.
View 7 Replies View RelatedWhen using the connect to the internet wizard in SBS 2008 (CTIW) the server comes back with an error that it cannot communicate with the router.Are there any settings that need to be configured in the ASA 5505 to allow communications with SBS 2008 using Exchange Server 2007? I am using ASDM 5.2 at this time.
View 3 Replies View RelatedIs it possible to configure bridge mode in asa 5505 if it is can u provide me a config.
View 1 Replies View RelatedI have an ASA 5505 running 8.4.4.1. I've configured three WAN interfaces and have assigned failover on one of them (we have two ISP's, and a total of 3 static IP's in 3 different subnets). I've noticed that all the traffic is flowing through only one of the three interfaces, but I need to allow incoming https traffic on the second WAN port so I can access our Exchange server (we already use https on the first WAN port to access another server).
[code] WAN1 is the default outgoing route and we've configured several incoming services on it (smtp and https for example) and appears to be working properly as mail is coming and going and users can access the RDS gateway.I need to configure WAN2 to accept https traffic and send it to our Exchange server to enable OWA (webmail) access.I've configured the same Access and NAT rules on all three WAN interfaces for smtp (but I suspect only the first one is currently functioning at this point, I'll test it next chance I get). I thought all I'd have to do is configure an access and NAT entry on WAN2 (same as on WAN1), but direct the traffic to the OWA server instead of the rds gateway server, but it is not working.
In the realtime log I can see that it appears to be receiving the traffic on the WAN2 IP, but seems to be passing this through to the inside via the WAN1 interface.
How to configure this setup.I have an ASA5505 with dual wan failover, FiOS (eth0) & Cable (eth1). how to configure the port forwarding for all my devices so it doesn't matter what external interface the traffic is coming from. For example, I need web traffic on port 80 forwarded to 192.168.1.150 regardless of whether it is coming through eth0 or eth1.
View 2 Replies View RelatedASA 5505 Firmware 8.3(4), ADSM 6.4(2).I have a public IP address of 168.87.3.4.I need to forward ports (5060, 5080, etc.) to one internal address. (192168.1.1).I need to foward different ports (10020-10080) to a different internal address (192.168.1.2) Everything I read tells me how to do this in a 1 to 1 static NAT.
View 1 Replies View RelatedI have a normal setup of ASA5505 (without security license) connected behind an internet router. From the ASA5505 console I can ping the Internet. However, users behind the Firewall on the internal LAN, cannot ping the Internet even though NATing is configured. The users can ping the Inside interface of the Firewall so there is no internal reachability problem. In addition, I noticed that the NAT inside access list is not having any hit counts at all when users are trying to reach the internet.
When i replace the ASA5505 with a router with NAT overload configuration on it, the setup works normally and users are able to browse the internet.
The ASA5505 configuration is shown below.
hostname Firewall
interface Ethernet0/0
description Connected To Internet Router
switchport access vlan 10
[Code].....
Can i access Cisco ASA 5505 Remotely Via Modem? l mean out of band management of Cisco ASA 5505? is that possible?
View 3 Replies View Relatedi have test to access the firewall of ASA5510 with ASA845-K8/asa902-k8bin + asdm-712.bin +JAVA6 / 7, is completely no problem
When i try to install a new ASA5505 existing IOS is asdm825-k8 and also asdm-712 with JAVA7 is not allow to access the firewall with ASDM
After i type in username password, it stuck on the page loading , sometimes it will come up with cannnot to the device something like that.
telnet and SSH is no problem, i still can download the IOS with TFTP.
I think may be the java problem, because i just to connect with wrong ip and password, it also stuck in this page.
There is web server at the internet. The firewall ASA5505 is located at the inside edge of the edge router and the internet is at the outside edge router of the edge router. The router has already been configured can route the outside network of firewall to internet. [code]
1. I have a host at the DMZ zone of firewall and if it wants to access this web server by http, the following command lines to be added to ASA5505 good enough and anything wrong with them? [code]
2.I have a doubt here that do I need to add any command line related to the Static Mapped address of 192.168.20.10/24 like below?
access-list Outside_DMZ extend permit tcp any 192.168.20.10 255.255.255.0 eq 80.whereby the 192.168.20.10 is the static mapped address of the Host at the DMZ to Outside Nertwork. Or, any other command related with the Static Mapped address have to be added?
I manage to configure the firewall 5505 so that it can ping between outside and DMZ and also between DMZ and inside.
Outside and Inside are not accessible to each other because Outside No Forward to Inside.
My purpose now wants to access the shared folder by Windows Explorer ( under Network ) between for example DMZ and inside. I tried to do it but cannnot even see the Host of the other party network. For example, if I open Windows explorer at DMZ, I can't see the Host at Inside Network. Same as I open Windows Exploere at Inside, I can't see also the Host at DMZ network.
How am I configure so that I can access the hsot as well as shared folder of two sites which already can ping each other?
I've been struggling with gaining access to the inter through our Comcast business gateway. We have had Comcast configure the device fro true static IP subnetting. Turned of local DHCP on the device etc. Here is my config.
ASA Version 9.1(1)
!
hostname TOCN-EX-01A-C5505-GW
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
[code]....
I have setup a Remote access VPN on my ASA5505 firewall through the ASDM wizard.I can successfully connect with the Cisco VPN client. My firewall also shows me the VPN session and shows incoming Rx packets. However, Tx packets remain 0, so no traffic is going out. My ASA5505 is configured as router on a stick with 25 different VLAN's. I want to restrict traffic to one specific VLAN using a crypto map.When I issue a ping -t command on my connected Windows box, the firewall log shows me the following message:
"IKE Initiator unable to find policy: Intf outside, Src: 10.7.11.18, Dst: 172.16.1.1."
"This message indicates that the IPSec fast path processed a packet that triggered IKE, but IKE's policy lookup failed. This error could be timing related. The ACLs that triggered IKE might have been deleted before IKE processed the initiation request. This problem will most likely correct itself." [code] I have really no idea what's going on. I have setup a Remote access VPN countless times but this time it shows me the error as described above.
I'm trying to make a very plain and simple network with the ASA 5505, I've strated from scratch over a dozen times triyng to find where I'm going wrong. My main goal is to simply create an IPSec VPN connection to my ASA 5505 and simply ping and connect to devices with the "inside network", so far I can easily create and establish a IPSec VPN Connection, but up to this point, I cannot successfully ping or access a single device on the ASA 5505 inside network.I've taken, create the IPSec profile with the ASDM wizard, add exemption for the VPN IP Pool, add access-list from this Cisco link, url...All this and I can't make a single connection to the inside network. [code]
View 7 Replies View RelatedI have a ASA5505 and I'm having trouble to achieve the following setup, block any kind of connection from outside except for IIS on port 80 and 443 but allow from the server to access any outside address, by domain or ip. Right now apps writen in C# on the server are throughing socket errors and Teamviewer remote control is not working, I would like it to replace remote desktop.
View 3 Replies View RelatedUsing an ASA5505, have 1 static outside address, want to access an inside SBS-Server on SMTP, RDP (3389), HTTPS and port 987
Have configured network object nat rules using the asdm, SMTP works (I can telnet to the server on port 25 from outside), however for some reason I can not telnet inside and out on port 25, so outgoing mail does not work. RDP does not seem to work from outside, 987 I havent tested from outside. When I try to create a network object nat rule for https I get this message from the ASA:
[OK] object network SBS-HTTPS
object network SBS-HTTPS
[ERROR] nat (inside,outside) static interface service tcp https https
NAT unable to reserve ports.
How can I get DMZ hosts to be able to access the Internet via the Outside interface of my ASA5505.I am using the DMZ to allow temp guest acces to the Internet.
Here is my configuration and it can be changed as needed.
User Access Verification
Password:Type '?' for a list of available commands.ciscoasa> enaPassword: *******ciscoasa# sho run: Saved:ASA Version 8.0(4)!
interface Vlan1nameif insidesecurity-level 100ip address 192.168.100.39 255.255.255.0!interface Vlan8no forward interface Vlan1nameif dmzsecurity-level 50ip address 172.31.10.1 255.255.255.0!interface Vlan11nameif outsidesecurity-level 0ip address 24.172.82.xxx 255.255.255.252!interface Ethernet0/0!interface Ethernet0/1switchport access vlan 11!interface Ethernet0/2!interface Ethernet0/3switchport access vlan 8!interface Ethernet0/4!interface Ethernet0/5!interface Ethernet0/6!interface Ethernet0/7!boot system disk0:/asa804-k8.binftp mode passivedns server-group DefaultDNSdomain-name asaobject-group protocol DM_INLINE_PROTOCOL_1protocol-object udpprotocol-object
[code]...
I am using ASA 5505 firewall with base-license. I connected my firewall to one cisco 3750 switch where i created 5 vlans. I done NATing for all vlans and they able to get internet and working fine. They able to browse all internet sites like gmail and yahoo mail.
All internal users are configured to use Outlook for their webmail. Here the problem is with outlook they are unable to send and receive the mails.
If they directly connected their system using public ip( Directly from ISP) they able to send and receive mails from outlook.
we have a cisco ASA5505 with base license and 3 interface configured. Internal 192.168.1.1/24 DMZ 172.16.0.1/24 Outside 20.20.20.20/24 The DMZ is configured to allow the traffic pass to the outside interface only (base license allow only traffic to one interface) in order to let clients on this network to browse internet. On the outside interface there's a nat configuration that let the port 443 to be natted to an in internal server. Is it possible to let the clients in DMZ to access to the internal server on port 443 from the outside interface?
View 3 Replies View RelatedI am trying to provide internet access to public and private SSID's on Cisco AP541n using VLAN's connected directly to ASA5505. VLAN1 is inside interface (private) and VLAN12 is wlan interface (public SSID). The AP541n is plugged into switch port 0/7 on an ASA 5505.Port 0/7 is configured as trunk mode. I have internet access when connected to private SSID but no internet access when connected to public SSID. why I can't access internet on public SSID?
logging class ip history emergencies
mtu inside 1500
mtu outside 1500
[Code].....
I am trying to troubleshoot a problem where in one of my remote site is not able to access some networks at HQ over Site to SIte VPN ( asa 5505 at Remote and 5520 at HQ). I ran packet tracer and HQ ASA looks clean as everything came out as ALLOW. Remote site ASA packet tracer give me DROP out at Phase 9 (VPN). I am not very sure what to look in ASA for resolution now. Is it an access list that is blocking the traffice or VPN setup.
View 5 Replies View RelatedI have a network with 3 sites that are on different subnets. Each site has an ASA Right now, I am only able to connect to the ASA that is connected to the subnet I am connected to.I want to be able to connect to the ASA that are on the remote subnets on the address of the inside interface.The sites are connected all together by site-to-site VPN.Is there any way I can achieve that without opening the outside interface directly on the Internet?
View 2 Replies View RelatedI have an ASA5505 running ver 8.0(2). I have configured the ssh timeout, ssh host commands and did the crypt o key gen. I am unable to access the device from the host I am allowing. Is there like ca save all command required? I am trying to use the default pix and telnet password. Do those still work?
View 3 Replies View RelatedYesterday, I configured ASA via CLI for Static PAT and created some entries in an access-list. I will be testing that setup this evening.
However on a quick double check of the settings on the device via ASDM I could not see the acess-list settings. I searched every tab and found nothing so I PuTTYed into the device and checked the running config. The rules I created were right there. Is this something I should expect? If so doesn't it defeat the point of having a GUI if it does not show a complete running config?
I am trying to access and ping the inside interface of a ASA5505 from a remote network. From the remote network, I am able to access anything on the local network, but the ASA5505 inside interface.The 2 networks linked by a fiber link which have a transport network on another interface. From the remote network, I am able to ping the transport network interface IP, but I would like to be able to ping the inside interface IP. When I do a packet tracer, I get a deny from an implicit rule.How can I achieve that?
Here are the subnets involved and the ASA5505 config.
Remote network : 10.10.2.0/24
Local network : 10.10.1.0/24
Transport network : 10.10.99.0/24
[code]....
This is my first time to use the Cisco ASA 5500 family. I have a request from a user to create an access rule, to allow all LAN traffic to Destination IP address 165.241.29.17, 165.241.31.254 with Destination TCP port 5060,5061,5070 and UDP port 50000-52399.
View 9 Replies View RelatedHow to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely.
View 3 Replies View Relatedi have a server with a private ip of 192.168.0.2, and NAT http port 80 to 192.168.0.2 so the outside world can access the web.. but my computer on the same lan as the server cannot use the domain name or public ip to access the web...i must use the http://192.168.0.2 to access. how to configure cisco 857 so i can use http://mydomain to access?
View 2 Replies View RelatedI currently have my 5505 setup for AnyConnect SSL VPN connections. Is it possible to also configure the 5505 for IPSec VPN connections? So, essentially my ASA will be capable of running SSL and IPSec VPN tunnels, concurrently.
View 2 Replies View RelatedI did some searching and the answers said it was supposedly possible but no info on how to do it. I am wondering if it is possible to configure a Cisco ASA 5505/10/20 to be a client to an existing (in this case) cisco client vpn. The reasons why are complicated (and imo irrelevant) but basically I need to be able to make a small network that can be on this vpn rather than individual machines.The client vpn is a basic IPSec over UDP Cisco VPN to an ASA5505.So how would I configure another ASA to connect to this like its a client?
View 3 Replies View RelatedI have to configure a default-factory firewall (ASA 5510) in a simple scenário like this image represents:At this moment i have configured the interfaces as represented above and at this moment what i want is grant access from a LAN computer (10.10.0.0/24) to the internet.
Should i configure some acl? I read that all traffic from an interface with a superior security level to other interface is allowed, so since my inside interface has a security level of 100 and the outside 0, it should be possible access to internet from an inside computer?!
From all configurations and examples i have seen around, they all contemplate a fixed IP address from the ISP, but in my scenário i have a dynamic one. This fact matter for the configuration i want to do?
My firewall is running the software version 8.2(5).