I have an ASA5505 running ver 8.0(2). I have configured the ssh timeout, ssh host commands and did the crypt o key gen. I am unable to access the device from the host I am allowing. Is there like ca save all command required? I am trying to use the default pix and telnet password. Do those still work?
View 3 RepliesWhat does a pinhole timeout indicate? [code]
ASA 5505 8.4(2)
I have a normal setup of ASA5505 (without security license) connected behind an internet router. From the ASA5505 console I can ping the Internet. However, users behind the Firewall on the internal LAN, cannot ping the Internet even though NATing is configured. The users can ping the Inside interface of the Firewall so there is no internal reachability problem. In addition, I noticed that the NAT inside access list is not having any hit counts at all when users are trying to reach the internet.
When i replace the ASA5505 with a router with NAT overload configuration on it, the setup works normally and users are able to browse the internet.
The ASA5505 configuration is shown below.
hostname Firewall
interface Ethernet0/0
description Connected To Internet Router
switchport access vlan 10
[Code].....
Version: Cisco ASA 5510 8.4(4)1
I've installed cisco asa 5510.
When I "show local-host all detail connection "
Normal situation:
105 myfailover:10.255.255.2/0 NP Identity Ifc:10.255.255.1/0,
idle 0s, uptime 1D14h, timeout 2m0s, bytes 18196822
But I got this output ( timeout - )
[URL]
I've been struggling with gaining access to the inter through our Comcast business gateway. We have had Comcast configure the device fro true static IP subnetting. Turned of local DHCP on the device etc. Here is my config.
ASA Version 9.1(1)
!
hostname TOCN-EX-01A-C5505-GW
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
[code]....
I just try to ping a internal Host but it want to go.
Laptop<===>ASA5505
Connected is the Laptop at Ethernet 0/2 Inside
My running-config is a clear config, only VLAN 1 has a IP and Ethernet 0/2 is up.
But If I try to ping to the Laptop I get the followed:
asa5505# ping 192.168.1.100
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.100, timeout is 2 seconds:
?????
Success rate is 0 percent (0/5)
asa5505#
From the Laptop to the ASA5505 I can Ping successfully.
I have Cisco ASA 5505 installed and use as default gateway. I go to Internet through the ASA5505 Here is my Problem.I can not ping from ASA prompt(ASA#) to my Laptop connected to the ASA, but i can ping the ASA inside interface from laptop i can not use ASDM and the VPN Tunnel is not working between the sie
ASA# ping 10.10.10.12
???????????
100% lost
Laptop c
C:/ping 10.10.10.1
!!!!!!!!!!!!!!!!
Here is the Topology
INTERNET .<=========================>ASA<===============================> LAPTOP
I disabled window firewall on the Laptop , but no goof result.
I am new to the ASA series and I am at a complete loss as to why I cannot configure this router to forward SMTP and RDP traffic to an internal host.
The packet trace tool in ASDM shows complete end-to-end connectivity for RDP but it still fails to connect from outside. This is my config file, what I need to change in order to make it work?
I have interited an ASA5505 problem. We're trying to manage the ASA remotely - we can connect to the device remotely via IPSec, we can ping other devices on the LAN network, but cannot ping the inside interface of the ASA - nor can we telnet/ssh/http to it. We can, however, connect to another router that's on the LAN and then SSH into the ASA's inside interface.
My IP via VPN: 10.133.20.8
The ASA interface we're trying to connect to via SSH or ASDM: 10.4.209.254
A router on the LAN we can connect to 10.4.209.250
We can ping other LAN devices such as 10.4.209.75, .90, .150 - so it's not a NAT/Route/Split Tunnel issue.I've attached the ASA config.
hostname ASA5505
enable password XXXXXXXXXXX encrypted
passwd XXXXXXXXXX encrypted
names
name 10.4.209.248 rpm_router
[code]....
I am ordering ASA5505-UL-BUN-K9. By default device comes with which IOS version?
View 3 Replies View RelatedI installed a CISCO ASA5505 with 50 user license to my network as the gateway firewall. So ASA is acting as the gaeway router which is connected to a fibre circuit and also it gives DHCP to the network. The strange thing is that except for two computers rest does not have internet. I also have an asterisk phone system which works fine..
I tried everything.... static IP's DHCP, DNS nothing worked. But strange enough two computers works fine and have internet.. but are no special computers. One is Win XP and the other one is Win7. When I troubleshoot the problem in win 7 on one of the computers it says
"The remote device or resource won't accept the connection"
ASA 8.2(5), uauth absolute timeout is disabled and inactivity timeout is set to 48 hours:
timeout xlate 48:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:00:00 absolute uauth 48:00:00 inactivity
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
Users still get kicked out every 8 hours and they have to reauth. This is a logging message:
%ASA-5-109012: Authen Session End: user 'john', sid 839, elapsed 28801 seconds
Internet ISP -> Juniper SRX 210 Ge-0/0/0
Juniper fe0/0/2 -> Cisco ASA 5505
Cisco ASA 5505 - >Inernal LAN switch.
1. Internet is connected to Juniper Ge0/0/0 via /30 IP.
2. Juniper fe0/0/2 port is configured as inet port and configured the Internal public LAN pool provided by the ISP. And this port is directly connected to Cisco ASA 5505 E0/0. Its a /28 pool IP address. This interface is configured as outside and security level set to 0.
From Juniper SRX, am able to ping public Internet IPs (8.8.8.8).
Issue:
1. From ASA am unable to ping public ip configured on Juniper G0/0/0 port.(/30)
2. From ASA no other Public internet IP is pinging.
Troubleshooting Done so far.
1, Configured icmp inspection on ASA.
2. Used the packet tracer in ASA, it shows the packet is flowing outside without a drop.
3. Allowed all services in untrust zone in bound traffic in Juniper SRX.
4. Viewed the logs when I was trying the ping 8.8.8.8 in ASA. It says "Tear down ICMP connection for faddrr **** gaddr **
I recently bought and installed a WAP4410N access point (using PoE) and it's running stable. I was able to access the web-based configuration by using the IP address of the AP (something like 192.168.0.184, coming from the DHCP of my router). However, I'm unable to access the web-based configuration using the host name of the device (mentioned next to the device name in the basic setup section of the web-based configuration). I changed the host name several times, but I can't connect to the device using the host name. Accessing the device by its IP address works, but I have to check the logging of my router to find out which IP address I have to use. Is there a way to access the device using the host name?
(I think my WAP4410N has firmware version 2.0.2.1 installed)
When I tried to upgrading PIX525 6.3 to 7.0 , Not able to Ping the host from the PIX 525 Inside interface which is on the same subnet, Also from the host to Inside Interface , Tried with Directly connected laptop with Cross cable and using Straight cable via switch, But the results end with fail.
View 2 Replies View RelatedI am using a Pix 515 with IOS 8.0(3).I have in my access list on the outside interface.......access-list outside_access_in extended permit icmp any 12.23.34.0 255.255.255.0 echo access-list outside_access_in extended permit icmp any 12.23.34.0 255.255.255.0 echo-reply.......in order to allow ping requests and ping replies into my inside network. This certainly works since I can ping the inside from outside and vice versa, but in the ASDM display of access rules, the hit count for these two lines is always zero. If I run 'show access-list', the hit count for these lines is non-zero.
Why doesn't the hit count show up in the ASDM gui display?Also, I have read that the PIX does not treat ICMP in the same way as TCP or UDP and there is no stateful behaviour towards ICMP. However, if I set up a continuous ping from outside to inside and then disable the above access list rule allowing echo requests towards the inside, the ping continues whereas I would expect it to stop.
In the config there is 'timeout icmp 00:00:02' if there is no stateful connection for ICMP, why is there a timeout value for it?
Recently, I have bought an ASA 5505 firewall which I have tried to connect to my ADSL router (Modem).It is now more than a week that I am trying to get internet connection through the firewall but I still can't succeed. I have tried many advices I get from this community but I still don't know what is wrong with my ASA Firewall configuration. From inside I am able to ping the inside and outside interface with a great success. and from my laptop which is connected to the firewall, I am able to ping the both interfaces (inside and outside) but still I can't access the internet.
As I don't have a static IP address from my ISP, I have configured the outside interface to pick up the ip address dynamically. Most of the time, the outside interface get the 192.168.1.2 ip address. [code]
Running ASA 5505
ASA Version: asa844-1-k8.bin
ASDM: Cisco ASDM 6.2(1)
I updated my ASA with version asa844-1-k8.bin.
However, whenever I try and run the ASDM client, I get the following error:
"Your ASA image has a version number 8.4(4)1 which is not supported by ASDM 6.2(1)."
How do I get the latest version installed on my Mac desktop? I know that I can connect via the web interface and run the ASDM client, but the same error persists. I have the asdm-649-103.bin file, but cannot connect to the ASA to install (I don't recall ever setting up SSH).
I have an unusual issue, for which I can find nothing on the net similar.
Setup:
ASA5505 = > CISCO3524 => Windows 2012 server
ASA is internet edge with ACL / NAT implemented.
We are wanting to implement inbound NATs for this server - 3389. We have many other servers on the internal side of this ASA that we are NATing to. Creating NATs using the same outside IP to another server is fine, no issues. This other test server resides on the same VLAN as the windows 2012 server. All IPv6 is turned off on the W2012 server, and it can web-browse out via the ASA as well. No matter what I do, however I cannot get iinbound NAT, on ANY port to this server working. Internally from another server to this server on any port is fine, i.e. we can RDP to this server without issue, so we know this works - the firewall on this server is turned off too. This is our ONLY w2012 server on the internal side. When we run a wireshark on the server whilst testing the NAT there is no traffic, so its getting blocked somewhere.
The config of the ASA is fairly big to to santize it and remove all customer reference would take a while to make display of this secure difficult.
I have a client ASA5505 generating this level 3 log message:
3 Mar 08 2011
19:48:34
IKE Initiator unable to find policy: Intf outside, Src: 192.168.0.2, Dst: 192.168.1.3
All the site-to-site tunnels on this ASA are up, so I don't know the meaning and signifcance of this log message or how to address it.
I'm attempting to configure an for both site-to-site and remote access VPNs. The site-to-site is working fine, however when I connect using the Cisco client, after initial connection and password prompt I get a "not connected" status. The log states that a policy map match could not be found. I have successfully set the unit up for remote access with no site-to-site and ran into another host of issues when adding the site-to-site to the working remote access config, so I started over setting up site-to-site first. I've attempted this through ADSM (hate it) - the current configuration is via CLI. I'm certain I'm just missing a piece or two.
View 2 Replies View RelatedThs only hapeens at one location. All the other locations are working the difference is this location goes through the firewall. If I bypass the firewall at this location it works.
View 1 Replies View RelatedI'm able to build my tunnel but unable to RDP nor ICMP back to the internal network.
VPN Client IP: 192.168.200.200
INTERNAL IP: 172.17.130.200
my configuration is below:
HOME-ASAFW02(config)# wr t: Saved:ASA Version 8.4(4)!hostname HOME-ASAFW02domain-name hsd1.nj.comcast.netenable password ViPq56cvd3SGvB08 encryptedpasswd 8bcozHCAwCqA5BmN encryptednames!interface Ethernet0/0description OUTSIDE-Connectionswitchport access vlan 2switchport protected!interface Ethernet0/1description INSIDE-Connectionswitchport protectedspeed 100duplex full!interface Ethernet0/2description WiFi-LinkSYSswitchport access vlan 3switchport protected!interface Ethernet0/3shutdown!interface Ethernet0/4shutdown!interface Ethernet0/5shutdown!interface Ethernet0/6shutdown!interface Ethernet0/7shutdown!interface Vlan1description INTERNAL-Networknameif insidesecurity-level 100ip address 172.17.130.129 255.255.255.128!interface Vlan2description OUTSIDE-Link-to-ISPnameif
[code]....
Basically after upgrade from ASA 8.4 to 9.0 (2) I have problems when certain types of NAT.Example:SA 8.4: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http while other ports can be accessed using the original IP (10.252.253.123).
ASA 9.0: nat (LAN, outside) 85 10.252.253.123 source static 192.168.3.2 192.168.3.2 192.168.3.104 static destination service http http In this form the host 192.168.3.2 uses the mapped ip (192.168.3.104) to access by http but unlike before now I cannot access to the original IP (10.252.253.123) using another port or ping from host 192.168.3.2.
I'm working on setting up a new ASA 5550, and have run into a question that I hope is easily answered.I currently have 4 interfaces, SL100 Inside, SL80 DMZ1, SL50 DMZ2, and SL0 Outside. I was under the impression that each interface, depending on security level would pass traffic from higher levels to lower, but not allow traffic being generated from SL80 to SL100.
What I would like to accomplish is that any hosts on my SL100 Inside interface can access the "internet" which is connected to my outside interface of the ASA, which was very simple, just a permit internal subnets eq www / https / etc...
My DMZ subnets need to access a few servers on my internal interface, and need outbound access to the world as well. Thinking that all traffic from my lower SL interfaces on the ASA would be denied, I entered a permit IP / DMZ subnet ------> any. This worked great for giving my DMZ hosts access to the internet, but it also permit traffic from the DMZ to hosts on my Inside interface as well.
Trying to allow inbound access from any host outside to my LAN server on port 995. [code]
View 1 Replies View Relatedi am using a Cisco 1841 with subinterfaces instead (NAT on a stick).From the internet i can access services on public IP being hosted in LAN2. But when i try to access the same services on the same public IPs but sitting on LAN1, it does not work.
View 1 Replies View Relatedi am using a Cisco 1841 with subinterfaces instead (NAT on a stick).From the internet i can access services on public IP being hosted in LAN2. But when i try to access the same services on the same public IPs but sitting on LAN1, it does not work.
View 3 Replies View RelatedThe old syntax that I am much more familiar with has been deprecated. On older IOS it would have been something like static (inside,outside) tcp 209.114.146.122 14033 192.168.30.69 1433 netmask 255.255.255.255 Plus an extended ACL to allow the traffic.I am trying to create a Static PAT to allow a host address to access our Network through an ASA. I have external address 209.114.146.122 that I want to hit the external interface on an obscure port (say 14033) and translate that traffic to an internal host address on port 1433.
View 11 Replies View RelatedOn remote site I have Cisco ASA5505, on cental site I have Cisco 2811 router, working site-to-site VPN tunnel. [code]
View 1 Replies View RelatedCan i access Cisco ASA 5505 Remotely Via Modem? l mean out of band management of Cisco ASA 5505? is that possible?
View 3 Replies View Relatedi have test to access the firewall of ASA5510 with ASA845-K8/asa902-k8bin + asdm-712.bin +JAVA6 / 7, is completely no problem
When i try to install a new ASA5505 existing IOS is asdm825-k8 and also asdm-712 with JAVA7 is not allow to access the firewall with ASDM
After i type in username password, it stuck on the page loading , sometimes it will come up with cannnot to the device something like that.
telnet and SSH is no problem, i still can download the IOS with TFTP.
I think may be the java problem, because i just to connect with wrong ip and password, it also stuck in this page.
There is web server at the internet. The firewall ASA5505 is located at the inside edge of the edge router and the internet is at the outside edge router of the edge router. The router has already been configured can route the outside network of firewall to internet. [code]
1. I have a host at the DMZ zone of firewall and if it wants to access this web server by http, the following command lines to be added to ASA5505 good enough and anything wrong with them? [code]
2.I have a doubt here that do I need to add any command line related to the Static Mapped address of 192.168.20.10/24 like below?
access-list Outside_DMZ extend permit tcp any 192.168.20.10 255.255.255.0 eq 80.whereby the 192.168.20.10 is the static mapped address of the Host at the DMZ to Outside Nertwork. Or, any other command related with the Static Mapped address have to be added?