Cisco Firewall :: Create Static PAT To Allow Host Address To Access Network Through ASA5510
Aug 23, 2012
The old syntax that I am much more familiar with has been deprecated. On older IOS it would have been something like static (inside,outside) tcp 209.114.146.122 14033 192.168.30.69 1433 netmask 255.255.255.255 Plus an extended ACL to allow the traffic.I am trying to create a Static PAT to allow a host address to access our Network through an ASA. I have external address 209.114.146.122 that I want to hit the external interface on an obscure port (say 14033) and translate that traffic to an internal host address on port 1433.
View 11 Replies
ADVERTISEMENT
Sep 15, 2011
At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I can't find it.I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this: [code] I do this,but it's not work.When I use EasyVPN client to connect ASA 5520,user could through authentication but will not get that static IP address which I configuration on Internal Users.so,what should I do,if anyboby knows how to use ACS 5.2 to create a static ip address user for remote access VPN.
View 2 Replies
View Related
Mar 20, 2012
I just upgraded my firewall to ASA 5505. Now, my original static ip address cofiguration is gone. Apperantly, Cisco went away from static ip address to something like nat (inside,outside) dynamic interface. how to create a static ip address under version 8.4? By the way, I am sharing what my configuration used to look before upgrading.
!
hostname cisco-asa
domain-name default.domain.invalid
names
!
interface Vlan1
nameif inside
security-level 100
[code].....
View 7 Replies
View Related
Sep 17, 2011
At first I use ACS 4.2 to create static ip address user for remote access VPN,It's easy,just configuration it at user set>Client IP Address Assignment>Assign static IP address,but when I use ACS 5.2 I dont't know how to do it.
I try to add IPv4 address attribute to user by read "ACS 5.2 user guide" ,it says this:
Step 1Add a static IP attribute to internal user attribute dictionary:
Step 2Select System Administration > Configuration > Dictionaries > Identity > Internal Users.
Step 3Click Create.
Step 4Add static IP attribute.
Step 5Select Users and Identity Stores > Internal Identity Stores > Users.
Step 6Click Create.
Step 7Edit the static IP attribute of the user.
I just do it,but it's not work.When I use EasyVPN client to connect ASA 5520,user could success to authentication but will not get the static IP address which I configure on Internal Users,so the tunnel set up failed.I try to Configure a IP pool on ASA for ACS users get IP address,and use EasyVPN client to connect ASA , everything is OK,user authenticate successed.but when I kill IP pool coufigurations and use the "add a static IP address to user "configurations,EzVPN are failed. how to use ACS 5.2 to create a static ip address user for remote access VPN?
View 7 Replies
View Related
Jan 6, 2013
how do i create network b/t vm ware and host machine ?
View 1 Replies
View Related
Apr 27, 2009
I would swear this worked at one point. I have a corporate office, and I have IPSec tunnels out to my outside offices. The corporate office has an ASA5510, and most of the remote offices are running off of Pix506s, one office has an ASA5505.
When anyone connects through WebVPN, using AnyConnect or not, they can contact any of the cifs shares for servers inside the corporate office. They cannot, however, contact cifs shares on servers that are in the remote offices.
View 4 Replies
View Related
Sep 3, 2011
We have an ASA5510 with the IPS ASA-SSM-10 module installed. All is working well except event notification. When sending a test email from the SSM IPS, we get the error "could not connect to SMTP host". The Exchange SMTP host does allow traffic from the IPS and ASA. I can ping to the SMTP host by IP and name. What am I missing here?
View 3 Replies
View Related
Sep 13, 2011
I've been trying to configure the threat-detection scanning-threat shun feature on my ASA5510 running 8.4(2) for some days now. From searching the support community I can see that I'm not the only one having a problem with this feature. The problem I'm having is that after configuring scanning-threat shun, no outside attacking hosts are being shunned. I'm using nmap to simulate a scanning attack. [code]
Is this the expected behavior of scanning-threat shun? If so this feature is of very little use to me as blocking my inside LAN is not my goal. I'm trying to protect my LAN from Internet attack. I can add the except command and exempt my LAN, but this still doesn't fix the problem of outside hosts not being shunned.
View 2 Replies
View Related
Jul 8, 2012
Up until recently one of my sites was able to get to a postilion subnet. Then we started receiving "host unreachable" e-mails. Posting told us SMTP traffic was not getting let in. I've compared the current config to a config that was saved before the issue popped up and found really no noticeable difference.
I tried a packet tracer trace with no luck: SiteB- Firewall# packet-tracer input outside tcp 11.2.2.36 12345 65.19.0.0 25.
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
[code]...
Result:
input-interface: outside
input-status: up
input-line-status: up
output-interface: outside
output-status: up
output-line-status: up
Action: drop
Drop-reason: (acl-drop) Flow is denied by configured rule
Attached is a sanitized config. I'm not entirely convinced it's a firewall issue, but I need to some successful testing to prove otherwise.
View 19 Replies
View Related
Jun 30, 2012
How many bits must be reallocated from host ID to network ID to create 16 subnets?( i did read the discussion on another page and still no clue). For the Class C network address 192.168.10.0 , which of the following subnet masks provides 32 subnets? How many host bits are necessary to assign addresses to 62 hosts ??
View 4 Replies
View Related
Feb 29, 2012
I want to create a Dual DMZ in a ASA5510 however it is not like I used to in ASA5505?In ASA5505 I create a Outside, Inside and DMZ VLAN and there after add the interfaces into the VLAN.This way I can have two DMZ interfaces, but how do I do it in a ASA5510?
View 1 Replies
View Related
Sep 20, 2012
How to configure our ASA to nat our to internetconnections, at the moment the first work fine,
ISP1 NAT
ASA5510 LAN
ISP2 NAT
View 1 Replies
View Related
Aug 25, 2012
We have network topology:
Inside Network (172.168.1.0/27) --- ASA5510----- Outside network (192.168.10.0/24)
ASA5510 have: Inside interface: 172.168.1.30/27; outside interface: 192.168.10.254
And we config:
# object network obj_inside
# subnet 172.168.1.0 255.255.255.224
# nat (inside,outside) dynamic interface
[code]...
So, we í in from outside, we can't access web at 192.168.10.10?
View 3 Replies
View Related
Mar 18, 2012
I have an ASA5510 running 8.2 code and I have over 200 static nats from the outside to the inside interface and that is how I expose our systems to the Internet. If this inside interface fails we also have a bypass interface that also terminates on the internal network but I am not sure how the nats will behave given they are statically mapped to the inside.
View 1 Replies
View Related
May 21, 2012
We are replacing our EOL Watchguard X1000 Firewall(s) with Cisco ASA 5510 unit - ASA Version 8.4(3). Following is the static NAT I have build and the corresponding access list.
nat (FW2Inside,FW2Outside) source static BW_XSP1_Private BW_XSP1_Public destinat
ion static BW_XSP1_Private BW_XSP1_Public
access-list FW2Outside_access_in extended permit tcp any object BW_XSP1_Public object-group DM_INLINE_TCP_1
Unable to access the server on the inside interface via the public NAT address. Can you point me in the right direction as to what I might be missing to make this work?
View 1 Replies
View Related
Dec 10, 2011
I have a ASA5510 with 2 internal interfaces (inside1 and inside2 same security level) configured with OSPF for dynamic routing with 2 routers to corporate subnets. I have a server in a private subnet that needs to be accessed from Internet. So static pat is used in ASA with the command
static (inside1, outside) tcp interface www 192.168.1.1 www netmask 255.255.255.255
As OSPF is in use, the subnet 192.168.1.0/24 may be reachable from interface inside2. When I tried to configure the static command for inside2,
static (inside2, outside) tcp interface www 192.168.1.1 www netmask 255.255.255.255.the error message came out "WARNING: mapped-address conflict with existing static...". Is this just a warning, or this is not possible in ASA.
View 2 Replies
View Related
Dec 12, 2012
Looking to have an ASA5510 with two internet feeds. Moreover, I would like to have my static nat translations continue to work on the backup feed. I have outbound nat working, however I cannot get the inbound nat to work. I had this all figured out in 7.x but now with 8.x I cannot seem to get it working. If anyone has a 8.x example config.
View 4 Replies
View Related
Apr 3, 2011
I have Cisco ASA5510 OS version 8.4(1), when i try to apply static command, this command is not found, the NAT issues used nat(inside,outside).
So why i can't found this command ?
View 1 Replies
View Related
Mar 30, 2011
We have several pairs of ASA5510s in failover A/P mode, some running 8.3(2) and others running 8.4(1).
e0/0 = outside
e0/1 = inside
m0/0 = management
The problem we're having is we can't get anything to route out of the management interface unless we put in a static route at least to the subnet level. For example, we want syslog traffic to exit out m0/0 to our syslog server 10.71.211.79. Our 'gateway of last resort' points to the next hop out e0/0, and a second static route with a higher metric and a more distinct network space is for m0/0 as in:
route outside 0.0.0.0 0.0.0.0 192.168.49.129 1route management 10.72.0.0 255.255.0.0 10.72.232.94 10
This doesn't work, and ASDM loggin gives this error: ".....Routing failed to locate next hop for udp from NP Identity Ifc:10.72.232.89/514 to management:10.72.211.79/514"
If I put in a more granular subnet route, or a host route of the syslog server it works, such as:
route management 10.72.211.0 255.255.255.0 10.72.232.94 10 <------------- this works
route management 10.72.211.79 255.255.255.255 10.72.232.94 10 <------------- this works too
Why won't a static route for 10.71.0.0 255.255.0.0 work in this case?
We are going to have numerous hosts access and be sent messages though the management interface of these ASAs, and it would be very burdonsome to have to add a host, or even a subnet, route for every one. I've removed all static routes and tried to rely on EIGRP, but that doesn't work. I also had to put 'passive-interface management' under the EIGRP for this to work.
Here is the pertinant ASA config concerning syslog, routing, and interfaces:
interface Ethernet0/0 nameif outside security-level 0 ip address 192.168.49.140 255.255.255.128 standby 192.168.49.141 !interface Ethernet0/1 nameif inside security-level 100 ip address xxx.xxx.xxx.xxx 255.255.255.128 standby
[Code].....
View 3 Replies
View Related
Jul 8, 2012
Instead of using a IP address I would like to use a host address that points to a NTP pool.An example would be:ntp server 0.north-america.pool.ntp.org Can this be done on the ASA series?
View 1 Replies
View Related
Feb 21, 2013
we have a cisco asa 5505 and it working great .i want to create web server that only selected public ip address can access.
View 3 Replies
View Related
Feb 7, 2013
Just want to know if there is a way to configure secondary IP address on the outside/public interface of ASA/PIX.One of our clients have used most of their IP on the subnet given by their ISP. They use those IP's for staticallymapping to Servers inside their local LAN. Thus, they requested another block/subnet from their ISP. They will also use this for static mapping/port forwarding to other servers in their network. The current UTM they are using is allowing this but they would like to use ASA/PIX as their main Firewall. Is this even possible or is there a workaround for this kind of scenario?
View 5 Replies
View Related
Sep 27, 2011
My customer has a 5510 with the inside interface connected to a routed port on a Cat3560G.When I look at the arp cache on the 5510 all inside IPs have the MAC of the 3560's routed port. [code]
View 6 Replies
View Related
Mar 25, 2011
I am configuring ASA 5510.
My ISP given /28 pool of public IP's. So i had total 14 available IP addresses.
I configured one IP to the my firewall outside interface. I want assign remaining IP's to the my Servers, which are located inside to the firewall.
View 2 Replies
View Related
Jun 23, 2011
Recently, I've been having significant problems with denial of service on our ASA-5510. Two IP addresses in particular attack my ASA regularly. What kind of rule do I need to create to deny these IP's access to my firewall?
View 4 Replies
View Related
Mar 10, 2011
we have two Cisco ASA 5510 in failover configuration.We tried to change the public IP address on the Outside interface of the primary device but it didn't works. The new IP is not reachable from Internet nor pingable from device on the same LAN.The new IP address is in the same subnet of the old IP.
From the switch on which the ASA is connected and from another Cisco PIX we can see the ARP entry. In the analysis, on the old public IP address there was a VPN site-to-site and Webvpn defined.We tried also to shut/no shut the interface and reboot the device.
View 1 Replies
View Related
May 28, 2012
We have a Cisco ASA 5520 and in order to conserve public IP addresses and configuration (possibly) can we use the same public IP address for a static NAT with two different interfaces? Here is an example of what I'm refering too where 10.10.10.10 would be the same public IP address.
-static (inside,Outside) 10.10.10.10 access-list inside_nat_static_1
-static (production,Outside) 10.10.10.10 access-list production_nat_static_1
View 2 Replies
View Related
Feb 3, 2013
I have ASA 5505 with basic licence, v9.1, ASDM 7.1. I want to create the DMZ for a web server.
The interface 0 is for the outside network The interface 6 is for the DMZ All other interfaces are for the inside network
My ISP provided me with one public static IP address, one gateway address and a subnet mask 255.255.255.252
1/ I would like to ask which interface I should assign the public static IP address to. Should it be assigned to the outside interface 0, or should it be assigned to the DMZ interface 6, while outside interface would be configured to use DHCP?
I tried to assign the static IP address to the outside interface first, but then when I used ASDM the “Public Servers” feature to configure NAT, I get error message that the outside interface and the public address cannot have the same IP address.
2/ For the sake of peace of mind, I am thinking about using the second firewall, which would be used only for the inside network. Can I connect this second firewall to one of the inside interfaces of the 1st firewall,
View 4 Replies
View Related
Jan 12, 2012
I want to create a VPN between two PC's, (the server "Data" and "Remote Desktop" check the topology below), the Router Clabeck (cisco 2811 ) is connected to the internet through int f0/0 using a PPPoE connection and connects all the LAN PC's by PAT to the internet (you can see all the configurations in the Show Run below), the "Remote Desktop" is any PC with internet connection.
F0/1 F0/0
DATA--------------------SW-------------------ROUTER(Cisco 2811)---------------------INTERNET---------------REMOTE DESKTOP
192.168.1.51 192.168.1.254 201.122.53.177 192.168.1.1
Current configuration : 2116 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
[code]....
View 1 Replies
View Related
Sep 15, 2011
Our proxy/anti-smap/IPS box called PROXY is behind our Cisco ASA firewall. The PROXY is set in transparent mode.The PROXY internal ip is 1.1.1.1 (internal ip)We have the MX record for mail.domain.com with public ip 9.2.7.5 (public ip as we entered with ISP public DNS)What happens now is that the emails that come through get "caught" by the PROXY and then we setup a thing whereby the emails are then forwarded from PROXY to our mail.domain.com server. Also, we made a static entry in PROXY whereby we can https to our email server for the outlook web access from outside of work therefore allowing for users to see the outlook web access web page.On the Cisco firewall, we put the static entry that 9.2.7.5 is mapped to 1.1.1.1 thus the mail server public ip is mapped to the PROXY.
Now, the box has this thing whereby it sends an email to all staff once a day telling them how many mails are legit, how many rejected and how many are spam - the spam emails are listed within the email and staff can at a click of a release button next to each spam email release a particular email from the PROXY box and make it to into their inbox. This works fine from the inside network, but I have issues from the outside due to the DNS and other things.I also put in the PROXY that any network can release spam and that our staff vlan can release emails. Also, on the inside of the firewall we did an access list that computers from staff vlan can access 1.1.1.1 on port 6552 (Which is the release spam port).Hence, we can release emails from internal network through the Microsoft Outlook.
On the outside network, we cannot release emails when using outlook web access.The host name for the PROXY release spam is proxy.domain.com so what we did also today is ask "ISP" to make an A record entry for another public ip which is 9.2.7.6 for proxy.domain.com.We meanwhile made an entry on the access list that comptuers from outside can access 9.2.7.6 on port 6552 (which is the release port).Now the only question is in regards to the static entries:
1. do we (and can we?) static map 9.2.7.6 to 1.1.1.1 through a port 3840 on the Cisco ASA (although we have already mapped 1.1.1.1 to 9.2.7.5 - I have a doubt here as this might mean we might not get emails? Or would we have to do the static again for this one specifcying the 9.2.7.5 as an smtp entry and the 9.2.7.6 as a release button?
2. have I made a mistake in general and should I have just told the ISP to make a CNAME entry for proxy.domain.com with the public ip 9.2.7.5 (which is the public ip for MX record?)?
View 9 Replies
View Related
Aug 22, 2011
I have an 8.3(2) ASA with a single outside IP. Dynamic PAT translates inside addresses to the outside interface address. I would like to use static NAT with port translation to access an inside syslog server. I got an error when I tried using the outside interface address. Can I use both dynamic PAT and Port Translation with the same outside address?This is what I would like to use but I receive an error saying there is an overlap using the outside interface address.(192.168.1.0 is my inside network. 10.10.1.10 is the outside interface IP.)
object network inside-net
subnet 192.168.1.0 255.255.255.0
nat (inside, outside) dynamic interface
object network SYSLOG_SERVER
host 192.168.1.50
nat (inside,outside) static 10.10.1.10 service tcp ssh ssh
View 6 Replies
View Related
Apr 11, 2012
o create a domain host
View 2 Replies
View Related
Jul 11, 2011
I am connected to a static ip network. This network sets local ips to connected computers but general ip is the same: static ip of network. When i go to "whatismyipaddress", I can see this static ip. I want to change my ip address. I have no chance to use proxy server or router connection. Is there a way to change my ip address? (Because some sites ban ip address, ex:rapidshare etc. and I need to change my ip)
View 1 Replies
View Related
