i have a server with a private ip of 192.168.0.2, and NAT http port 80 to 192.168.0.2 so the outside world can access the web.. but my computer on the same lan as the server cannot use the domain name or public ip to access the web...i must use the http://192.168.0.2 to access. how to configure cisco 857 so i can use http://mydomain to access?
View 2 RepliesThis is my first time to use the Cisco ASA 5500 family. I have a request from a user to create an access rule, to allow all LAN traffic to Destination IP address 165.241.29.17, 165.241.31.254 with Destination TCP port 5060,5061,5070 and UDP port 50000-52399.
View 9 Replies View RelatedHow to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely.
View 3 Replies View RelatedI have to configure a default-factory firewall (ASA 5510) in a simple scenário like this image represents:At this moment i have configured the interfaces as represented above and at this moment what i want is grant access from a LAN computer (10.10.0.0/24) to the internet.
Should i configure some acl? I read that all traffic from an interface with a superior security level to other interface is allowed, so since my inside interface has a security level of 100 and the outside 0, it should be possible access to internet from an inside computer?!
From all configurations and examples i have seen around, they all contemplate a fixed IP address from the ISP, but in my scenário i have a dynamic one. This fact matter for the configuration i want to do?
My firewall is running the software version 8.2(5).
I have a closed network that is not connnected to the internet, just other sites that we want to communicate with. We have a cisco router connected to the outside interface on an ASA5505 and a cisco router connected to the inside interface on the same ASA5505. I have an inside interface that connects our management LAN, five separate DMZ interfaces with a separate LAN (VLAN) on each DMZ interface and the outside interface that connects to the other sites. Data is not allowed to mingle between the five DMZ's.
Alll connections to the other separate nodes are handled with the router on the external interface. IPSEC GRE tunnels have been established between all sites and BGP routing has been verified. Pings are good between inside, dmz and external interfaces and between the DMZ's and the other sites, to include hosts on our local networks and hosts at the remote sites. Inter and intra traffic is enabled.
When a remote site attempts an https connection, the initial ACK handshake makes it through the ASA5505, but the return SYN/ACK is being knocked down and I don't understand why (it is not because of ACL's, they are any any at this point).
Why the return SYN/ACK to the remote site isn't getting through the ASA5505 outbound. Will probably have the same issue with FTP, but right now, just trying to solve one problem at a time.
ASA5505 is in routed mode, not looking to NAT since the IP addresses in the DMZ need to be reached by their real IP address.
I just started at a new company and they want to use iphones in place of blackberry's, what a surprise. We have a exchange server and blackberry enterprise server. My question is how do I configure the cisco ASA to allow for iphone vpn connection and start replacing our blackberry's.
View 1 Replies View RelatedCisco ASA 5510 and I want to configure it as an access gateway following this .[URL] the basic configuration steps on what to do on ASDM.
View 2 Replies View Relatedi have cisco ASA5520 and i have a remote access vpn .I want to configure logging for this remote access vpn.
i want the time user connected .how log it is connected .If any error while connecting ?
I'm trying to configure an extended access list on one AS5350XM but I get one way hearing on a voice calls and I can't determine why (please see the attached diagram). There is an OSPF running on both gigabit interfaces and the Loopback address is also advertised (it is actually the voip IP address). The access list is applied on both interfaces in the inbound direction. There is another gateway with IP:4.4.4.4 (no firewalls here) and the routing between gateways is working properly.
Here is part of the access list (applied on AS5350):
.
.
permit ip host 4.4.4.4 host 3.3.3.3
.
.
When I review the log of the AS5350xm I see many errors like this one:
%SEC-6-IPACCESSLOGP: list example denied udp 3.3.3.3(16638) -> 4.4.4.4(18094), 1 packet
So how it is possible to see this error since the access list is in inbound direction and the IP address (4.4.4.4) is open. I don't have problems when I do telnet or ssh from 3.3.3.3 to 4.4.4.4.
I have an auditor wanting a screenshot of all users that have acces to configure our firewall, I am unfamiliar with 5.1. Is there a way of running such a report on a paticular device?
View 1 Replies View RelatedHow do I connect and configure my WAP54G wireless access point to my new Cable Modem? I have it connected to the modem but I cannot access it to configure it. It appears to be working but before I got the cable modem I had it connected to a router and it was set-up with a static IP address. With my new ISP, I no longer have a static IP address so I am trying to configure the WAP54G to use DHCP. Trying to access it thru the internet at 192.168.1.245 does not work.
View 1 Replies View RelatedWe heard that ASA ver 8.4 has PBR. Do we have some guidelines on how to configure PBR for ASA and can it do routing based on URL?
View 2 Replies View RelatedHow to configure ASA failover for 8.4.
View 1 Replies View RelatedI'm having a problem configuring an ASA 5510. A previous employee started the config and left abruptly. He established a VPN Tunnel between two of our sites and that's working without an issue. The problem is, the network behind the 5510 at the remote location cannot access the internet.
ASA Version 8.2(1)
!
hostname PH-Firewall
domain-name pleasehelpme.com
enable password HXrQty4kqW8s8yeE encrypted
passwd ucA.qrYJWD9UyIFz encrypted
names
[code]....
I have a asa 5505 Sec plus with 3vlan, inside, outside and dmz.
On the outside i have 5 ip's for my use, and in the dmz i have a webserver that need to communicate with one sql server on the inside.
The "sql" also needs to be accessible from outside and thus has a static nat with a dynamic nat so it replies from same ip as on nat ie 72.72.72.5 webserver is natted with 72.72.72.6
sql inside ip is 192.168.1.2, gw 192.168.1.1
webserver ip is 192.168.2.100 gw 192.168.2.1
sec lvl on inside is 100 and on dmz 50
with a dynamic policy running inside-net/24 to dmz-network/24 translagt to dmz 192.168.2.2 i can get it to ping 1 way from inside to dmz, but not the other way around...
All i need is to open 1 port ie 6677 both ways for this communication to work.
I'm not very familiar with the CLI and do most stuf in GUI (know i should learn CLI, but time doesnt let me)...
on access rules i have just added everything from any to any using , ip, icmp, tcp and udp just to be sure... :-)
I am confiuging a DMZ on my ASA 5510 but I have run out of physical ports, since I have dual Wan ports configured. I plan to implement a DMZ using subinterfaces. I have 2 questions:
1) Do I need to configure a Vlan to complete this task?
2) Do I need to re-configure the other interfaces for subinterfaces and/or vlans as well?
Do you know how to configure PAT on Cisco ASA 5545x?
View 2 Replies View RelatedWe have Cisco ASA 5520 firewall. ASA Version - 8.0(4). ASDM Version - 6.1(3). Firewall Mode - Routed.
We want to configure QoS for some subnets and enable policing such that they cannot use more than 1mb of bandwidth. I think we cannot create more than 1 policy for it. In that case i created a policy with QoS enabled and configured the Input and Output policing with Commited Rate of 1024000 bits/second. But it does not seem to work.
how can i create such policy in the ASA to limit certain subnets to 1mb bandwidth ?
I'm trying to configure an asa 5510 8.2(1)?I have a range of pub ips 3*.108.234.145-150
>>> E0/0 3*.108.234.146 outside public
>>> E0/1 192.168.1.1 inside
>>> E0/2 192.168.3.1 dmz
would like to map dmz host 192.168.3.107 to external 3*.108.234.147 on port 5000 and 50001 LOCAL LAN should also be able to get to dmz host ports.i've tried a few configs and also following this example:
[URL]
without any luck, here is my config, also posted the out put of show arp which is able to see and ping the host on dmz, also the output of show access-list which shows hits to it.
prophase-pix(config-if)# show running-config
: Saved
:
ASA Version 8.2(1)
!
hostname prophase-pix
enable password encrypted
[code]....
i'm trying to configure an ASA with two ISP to be reached from internet for vpn access, the objective is that the user can use any of the Public address attached to ASA to connect to the company. Is this possible? i'm facing some problems because i can not use two different default routes (same AD) pointing to two different interfaces, this is the message that i receive "ERROR: Cannot add route entry, possible conflict with existing routes" and when i change the AD of one of the default routes i just can reach one ISP.
View 1 Replies View RelatedI'm using windows XP Pro , in a local Lan, internet connection through a DHCP, and System software on IP 192.168.0.254. I'm the Admin of my PC, I just want to use the Internet and the System program. I want to block any user from accessing my PC or viewing my Processes by other programs like (Ideal Admin.). How to configure the AVG Firewall to do that ??
View 11 Replies View Relatedthis is a project and my configred file:I can't config access list according to the project.
View 19 Replies View RelatedI am trying to configure Remote Access VPN in our Cicco ASA 5520 firewall through SSL VPN wizard. I tried to configure Anyconnect VPN client option, but after entering user/pass it gives error "An error was received from the secure gateway in response to the VPN negotiation request. Please contact your network administrator. The following message was received from the remote VPN device: No assigned address"
As looking online there is no easy step-by-step option for same. I want to provide Remote Access VPN to some of our user abroad who should have access to few server applications and no internet access.
I am trying to configure Cisco 887-W ISR but have hit a stumbling block when trying to configure the wireless access point- or at least the advanced features of the access point using the URL referenced in from the cisco GUI configuration utility (Cisco Configuration Professional ). I do recall previously reading a post which referenced a different URL.
View 2 Replies View RelatedI can not access the configure menu.
I try access with Serial cable blue DB09 / RJ45 on console port and serial ports on PC using putty or hyperterminal but any connection can not be done. The screen stay black and not show any text.
The computer found the port COM1 but i csn not access any information from Cisco router model 1841
Configuring Cisco 1841 router and firewall.My provider has put their equipment and given me 2 subnets with public ip address. I am used to getting just one Subnet and connecting my firewall straight to the hand off. But in this case I am a bit confused. I assume I will need to put a router and configure it with before I connect my firewall. [code] I also have a firewall that I would like to be on the subnet 2 at 200.xxx.97.130 and have my private network 192.168.xxx.xxx behind it.
View 2 Replies View RelatedWe just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
View 8 Replies View Relatedconfigure the firewall Cisco ASA5510 in HA Mode.Enclosed Network diagram.
View 14 Replies View RelatedI am attempting to set up failover dual ISP on a 5505 running 8.4(4) with the Sec Plus license. Everything i have been able to reference so far, points to old commands not available or relevant in 8.4
For instance:
global (backup) 1 interface
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 20.20.20.1 1
route backup 0.0.0.0 0.0.0.0 30.30.30.1 10
What is the new syntax that should be used to mimic these commands? I have the sla and trach reachability configuration already set up.
How to config RDP to internal host from outside. With new OS, unable to configure RDP having issue with NAT commands are different.
View 1 Replies View RelatedI am trying to configure an IPSEC vpn on an ASA5505 I setup an SSL vpn and it works fine, I can browse to the https: address log in and connnect to servers However when I try to setup the ipsec client access vpn it will not connect and I am getting the errors below I used the wizard for the initial configuration Looks like the inital IKE is being blocked or dropped?
%ASA-7-710005: UDP request discarded from my external IP/35781 to external:ASA-external/500
%ASA-7-710005: UDP request discarded from my external IP/35781 to external:ASA-external/137
I have a firewall Cisco ASA 5505, and currently it is a command line firewall. I want to configure ASDM so that i can use it as a GUI Web Base interface.I really don't know what to do. How can I configure ASDM on my firewall.
View 7 Replies View Relatedif there is a way to configure pim-ssm on asa 5585x-ssm20.
View 1 Replies View Related