Cisco Firewall :: Way To Configure Pim-ssm On Asa 5585x-ssm20
Aug 6, 2012if there is a way to configure pim-ssm on asa 5585x-ssm20.
View 1 Replies
ADVERTISEMENT
Cisco Firewall :: Upgrade From ASA-5510 SSM20 To ASA-5515X?
Dec 25, 2012I need to upgrade to firewall which supports Active/Standby configuration.I am currently using a ASA-5510,SSM-20 8.2(5).Will the configuration file from the ASA-5510 work on the 5515X?
View 1 Replies View RelatedCisco Firewall :: Recommended Stable Code For 5585x Firewall?
Mar 20, 2013Looking for a recommended code on the ASA 5585x firewall. We ran into a bug (CSCtr24705) on version 8.4.2 where it rebooted the primary firewall. The bug has to do with modifying an existing ACL that's part of a custom policy-map inside a service-policy. If we upgrade to 8.4.5 (which has the previous bug fix in it), there is another major bug (CSCud70273) where if you use the packet-tracer input command on an inside interface it causes problems too.
I don't understand why packet-tracer input would have a bug associated with it when it's been around for a long time and we use it on a daily basis for troubleshooting. Is there stable code for the 5585x to upgrade to without running into possibly a major bug? This is our core firewall so there are no VPN tunnels on it. It's setup in active/standby failover in routed mode.
Cisco Firewall :: What Is Latency Value For ASA 5585X And 5555X
Apr 16, 2013I am wondering what is Latency value for Cisco ASA 5585X and 5555X . I can see on websites that it says "low latency firewall" but I dont see any value.
View 1 Replies View RelatedCisco Firewall :: 5585x - Multiple ISPs Plus WAN And DMZ
Aug 17, 2011Looking to replace an "all-in-one" type firewall (UTM/Firewall, SSL VPN) with a cisco product - the issue i'm running into is that we have multiple ISPs plus WAN and DMZ - overall more than 5 ports on mid-range ASA devices - and from what i read, adding 4-port module precludes me from adding CSC module.
Is there an solution to that other than going for 5585-x model? (kind of over our budget, granted we need 2 for failover)
Cisco Firewall :: ASA 5585x - Create The Outside Interface On A Subinterface?
Oct 31, 2012I have a circuit that will be delivered to a client next week and we are installing an ASA 5585x for them. They will have a circuit coming in with a few VLANs configured on it. One VLAN for the Internet and one for connectivity to another client.
So does the ASA allow you to create the "outside" interface on a subinterface?
Cisco Firewall :: ASA 5585x Running 8.4 - Applying ACL Globally
May 4, 2011I will be supporting a new ASA 5585X running 8.4 and I was wondering if it's possible to apply an ACL globally instead of it as an access group that is applied to a specific interface as in or out ... below are the interfaces and ACl.
View 2 Replies View RelatedCisco Firewall :: ASA 5585x Security Context In HA Cluster
Jun 6, 2012I have a active-active setup with 2 cisco asa 5585x running 8.4 - the boxes ahve each 2 sec context's build-in - which gives 4 sec context in the cluster. I have 2 x 5 extra licenses (2 x ASA5500-SC-5) which I haven't applied yet - will this give me a total of 10 or 14 security contextes? I am a bit in doubt because if I only get 10 sec contextes in this cluster then could I instead get a single 10 security context license (1 x ASA5500-SC-10) and add this - hereby I would get 12 then.
View 1 Replies View RelatedCisco Firewall :: ASA 5585X - Possible To Have Content And Control Security?
Aug 10, 2011Is it possible have Content Security and Control Security in a ASA 5585-X? I´m asking because the CSC-SSM is only supported in ASA 5540, 5520 and 5510 and I dont know how it feature ca be supported on a new ASA 5585-X.
View 2 Replies View RelatedCisco Firewall :: ASA 5585X URL Filtering / Unable To Support CSC Module?
Aug 22, 2011Because ASA5585X doesn't support CSC module, how can do URL filtering on ASA5585X
View 1 Replies View RelatedCisco Firewall :: ASA 5585X Nexus Switches Utilizing VPC Technology
Jul 17, 2012I want to configure 5585x Active/Standby with 2 nexus switches utilizing VPC technology. New ASA 8.4 supports etherchannel so I want to plugin 2 cables from ASA1 to sw1 and sw2 and 2 cables from ASA2 to sw1 and sw2? Is this a valid design? how would I configure that? Any design document on that?
View 1 Replies View RelatedCisco Firewall :: ASA 5585x Working Fine But No Console Access
Feb 9, 2012I have an asa 5585x cluster. I get ssh access but no console access on the standby unit.
On the active unit, when I try console access, ASA ask for a password. I have tried all the one that I have configured, but without success.
Cisco Firewall :: 5585x - Threat Detection Log Entries In Multi Context Mode
Dec 29, 2012We have a 5585X running in multi context mode, and we are getting log entries for scanning threat detection, such as:
%ASA-4-733100: [ Scanning] drop rate-1 exceeded. Current burst rate is 2 per second, max configured rate is 10; Current average rate is 5 per second, max configured rate is 5; Cumulative total count is 3116
Threat detection is not supported in multi context mode so I cannot tune the thresholds, is there any way that I can get rid of this outside of messing about with logging levels/message IDs?
Cisco Firewall :: ASA 5585X Active / Active Failover Group Inter Routing
Mar 20, 2012I am looking at deploying a pair of 5585X's in an active/active multiple context state. I am creating Mulitple contexts that need to be able to route to each other. I was going to deploy a type of Gateway context that has a shared interface to all of the other contexts, instead of sharing interfaces directly between the contexts, i beleive this will work as basically i am just cascadng the contexts and sharing interfaces.
The main problem i have come across, is that if i deploy active/active across two appliances using 2 failover groups i can not see a way to route between them, for example.
I have Context 1, Context 2 and Context GW A including the shared interfaces of Con1 and Con2 in failover group 1 on appliance A with the respective standbys on Appliance 2. I have Context 2, Context 4 and Context GW B including the shared interfaces of Con 3 and Con 4 in failover group 2 on appliance B with the respective standbys on Appliance 1.
I need to be able to route traffic between Context GW A and GW B so that the contexts can communicate in normal operation and in failover. I do not beleive that I can share an interface between contexts in two separate failover groups and to be honest without adding a L3 device between the appliances i am not sure if this is possible.
Cisco VPN :: RDP Plugin For ASA-5585x
Jan 15, 2013I'd like to add an RDP to the vpn portal page on our 5585x. Looking for the rdp plugin in the 5585x download area but there is no page for Remote access plugins. Would the plugin be the same as any of the 5500 ASAs? Could I just download the rdp_09.11.2012.jar file from the 5505 download area?
View 1 Replies View RelatedAAA/Identity/Nac :: 5585X ASA Anyconnect VPN IP Allocation
Sep 1, 2011Starting a project where they customer has ASA 5585X with SSP40 with 10K SSL Premium Lic and ACS5.1.The cust wants IPSec, and Anyconnect Client terminations. The number of users will be close to 6000 and will scale.Due to the huge scale of users, i am not able to finalize a design. Have the following doubts.
1. Will ACS have any issues in supporting a database this huge. OR is it better to go with the AD/LDAP integration.
2. What is the best way to allocation IP address. Does ACS 5.1 support dynamic allocation form an IP pool.
I have been browsing through the forum, couldnt find anything concrete.
Cisco Switching/Routing :: Spanned Etherchannel ASA 5585X And Avaya VSP9000?
Apr 7, 2013We have a pair of ASA 5585X firewalls that need to connect to a pair of Avaya VSP9000 switches. The Cisco docs refer to doing spanned etherchannel with a Cat 6500 switch using VSS or a Nexus switch using VPC. Does spanned etherchannel work with non Cisco switches or is this proprietary? The etherchannel on the ASA is setup using LACP. Here's applicable configuration:
interface TenGigabitEthernet0/6
channel-group 2 mode active vss-id 1
!
interface TenGigabitEthernet0/7
channel-group 2 mode active vss-id 2
!
interface Port-channel2
port-channel span-cluster vss-load-balance
Cisco Firewall :: How To Configure Firewall Access For ASA 5510
Nov 4, 2012This is my first time to use the Cisco ASA 5500 family. I have a request from a user to create an access rule, to allow all LAN traffic to Destination IP address 165.241.29.17, 165.241.31.254 with Destination TCP port 5060,5061,5070 and UDP port 50000-52399.
View 9 Replies View RelatedCisco Firewall :: How To Configure PBR For ASA 8.4
Aug 12, 2012We heard that ASA ver 8.4 has PBR. Do we have some guidelines on how to configure PBR for ASA and can it do routing based on URL?
View 2 Replies View RelatedCisco Firewall :: How To Configure ASA Failover For 8.4
Nov 23, 2011How to configure ASA failover for 8.4.
View 1 Replies View RelatedCisco Firewall :: How To Configure ASA 5510
Sep 11, 2011I'm having a problem configuring an ASA 5510. A previous employee started the config and left abruptly. He established a VPN Tunnel between two of our sites and that's working without an issue. The problem is, the network behind the 5510 at the remote location cannot access the internet.
ASA Version 8.2(1)
!
hostname PH-Firewall
domain-name pleasehelpme.com
enable password HXrQty4kqW8s8yeE encrypted
passwd ucA.qrYJWD9UyIFz encrypted
names
[code]....
Cisco Firewall :: Configure Dmz On ASA5505
Dec 20, 2011I have a asa 5505 Sec plus with 3vlan, inside, outside and dmz.
On the outside i have 5 ip's for my use, and in the dmz i have a webserver that need to communicate with one sql server on the inside.
The "sql" also needs to be accessible from outside and thus has a static nat with a dynamic nat so it replies from same ip as on nat ie 72.72.72.5 webserver is natted with 72.72.72.6
sql inside ip is 192.168.1.2, gw 192.168.1.1
webserver ip is 192.168.2.100 gw 192.168.2.1
sec lvl on inside is 100 and on dmz 50
with a dynamic policy running inside-net/24 to dmz-network/24 translagt to dmz 192.168.2.2 i can get it to ping 1 way from inside to dmz, but not the other way around...
All i need is to open 1 port ie 6677 both ways for this communication to work.
I'm not very familiar with the CLI and do most stuf in GUI (know i should learn CLI, but time doesnt let me)...
on access rules i have just added everything from any to any using , ip, icmp, tcp and udp just to be sure... :-)
Cisco Firewall :: Configure DMZ On ASA 5510
Mar 3, 2013I am confiuging a DMZ on my ASA 5510 but I have run out of physical ports, since I have dual Wan ports configured. I plan to implement a DMZ using subinterfaces. I have 2 questions:
1) Do I need to configure a Vlan to complete this task?
2) Do I need to re-configure the other interfaces for subinterfaces and/or vlans as well?
Cisco Firewall :: How To Configure PAT On ASA 5545x
Nov 15, 2012Do you know how to configure PAT on Cisco ASA 5545x?
View 2 Replies View RelatedCisco Firewall :: ASA 5520 - Configure QoS
Mar 10, 2011We have Cisco ASA 5520 firewall. ASA Version - 8.0(4). ASDM Version - 6.1(3). Firewall Mode - Routed.
We want to configure QoS for some subnets and enable policing such that they cannot use more than 1mb of bandwidth. I think we cannot create more than 1 policy for it. In that case i created a policy with QoS enabled and configured the Input and Output policing with Commited Rate of 1024000 bits/second. But it does not seem to work.
how can i create such policy in the ASA to limit certain subnets to 1mb bandwidth ?
Cisco Firewall :: How To Configure ASA 5510 8.2(1)
Jul 25, 2011I'm trying to configure an asa 5510 8.2(1)?I have a range of pub ips 3*.108.234.145-150
>>> E0/0 3*.108.234.146 outside public
>>> E0/1 192.168.1.1 inside
>>> E0/2 192.168.3.1 dmz
would like to map dmz host 192.168.3.107 to external 3*.108.234.147 on port 5000 and 50001 LOCAL LAN should also be able to get to dmz host ports.i've tried a few configs and also following this example:
[URL]
without any luck, here is my config, also posted the out put of show arp which is able to see and ping the host on dmz, also the output of show access-list which shows hits to it.
prophase-pix(config-if)# show running-config
: Saved
:
ASA Version 8.2(1)
!
hostname prophase-pix
enable password encrypted
[code]....
Cisco Firewall :: Configure ASA 5520 With 2 ISP?
Mar 18, 2012i'm trying to configure an ASA with two ISP to be reached from internet for vpn access, the objective is that the user can use any of the Public address attached to ASA to connect to the company. Is this possible? i'm facing some problems because i can not use two different default routes (same AD) pointing to two different interfaces, this is the message that i receive "ERROR: Cannot add route entry, possible conflict with existing routes" and when i change the AD of one of the default routes i just can reach one ISP.
View 1 Replies View RelatedWindows XP Pro - How To Configure AVG Firewall
Aug 30, 2012I'm using windows XP Pro , in a local Lan, internet connection through a DHCP, and System software on IP 192.168.0.254. I'm the Admin of my PC, I just want to use the Internet and the System program. I want to block any user from accessing my PC or viewing my Processes by other programs like (Ideal Admin.). How to configure the AVG Firewall to do that ??
View 11 Replies View RelatedCisco :: Configure 1841 Router And Firewall?
Feb 11, 2013Configuring Cisco 1841 router and firewall.My provider has put their equipment and given me 2 subnets with public ip address. I am used to getting just one Subnet and connecting my firewall straight to the hand off. But in this case I am a bit confused. I assume I will need to put a router and configure it with before I connect my firewall. [code] I also have a firewall that I would like to be on the subnet 2 at 200.xxx.97.130 and have my private network 192.168.xxx.xxx behind it.
View 2 Replies View RelatedCisco Firewall :: Pix 515E Could Configure The Device
Oct 2, 2012We just switched over from a T1 line to 50/4 Mbps cable Internet. The speed was fine with the T1, but when we switched over to cable, the download speeds didn't increase. I'm getting 2-3 Mbps up and still only 1.5 Mbps down. I inherited this network a few years ago, so I didn't configure the Pix initially but I have been managing it and can't find a setting limiting the bandwidth for the liffe of me. I know it's not the Internet because when I connect a computer straight to the modem, the speed is great. As soon as I put it through the Pix though, it slows way down.
View 8 Replies View RelatedCisco Firewall :: Configure The ASA5510 In HA Mode?
Jun 4, 2012configure the firewall Cisco ASA5510 in HA Mode.Enclosed Network diagram.
View 14 Replies View RelatedCisco Firewall :: Configure Dual ISP On 5505 8.4
Mar 27, 2013I am attempting to set up failover dual ISP on a 5505 running 8.4(4) with the Sec Plus license. Everything i have been able to reference so far, points to old commands not available or relevant in 8.4
For instance:
global (backup) 1 interface
global (outside) 1 interface
nat (inside) 1 0.0.0.0 0.0.0.0
route outside 0.0.0.0 0.0.0.0 20.20.20.1 1
route backup 0.0.0.0 0.0.0.0 30.30.30.1 10
What is the new syntax that should be used to mimic these commands? I have the sla and trach reachability configuration already set up.
Cisco Firewall :: Configure SSH Only Access On PIX 506e
Mar 4, 2011How to configure SSH access on my PIX 506e. I would like to use local authentication with no AAA server. Also I would like to have telnet disabled completely.
View 3 Replies View Related