Is it possible have Content Security and Control Security in a ASA 5585-X? I´m asking because the CSC-SSM is only supported in ASA 5540, 5520 and 5510 and I dont know how it feature ca be supported on a new ASA 5585-X.
View 2 RepliesI have to upgrade to an ASA 5510 CSC, and the new license is generated, the file you sent me licensing, only seen this:Activation Code not required for this renewal. Please go to "Administration> Product License" in the CSC SSM console and click "Check Status Online" to get the latest expiration date (BASE: 09/04/2014, PLUS: 09/04/2014).This means that what I have not make any upgrades or license charge in the ASA? Does the automatic update is made?
View 1 Replies View RelatedI have a active-active setup with 2 cisco asa 5585x running 8.4 - the boxes ahve each 2 sec context's build-in - which gives 4 sec context in the cluster. I have 2 x 5 extra licenses (2 x ASA5500-SC-5) which I haven't applied yet - will this give me a total of 10 or 14 security contextes? I am a bit in doubt because if I only get 10 sec contextes in this cluster then could I instead get a single 10 security context license (1 x ASA5500-SC-10) and add this - hereby I would get 12 then.
View 1 Replies View RelatedWe want to have a ASA5510 with both IPS function and Content Security feature, while I checked on Cisco website, looks like ASA5510 or 5520 only have one SSM slot, so I can only use either AIP module or CSC module, does it mean I can not get both features at the same time.
Right now I want to have IPS function and anti-spam, anti-virus, antiphishing, content filtering, URL blocking such feature, so what do I need to buy to have all of these function in one device?
Our requirement with that appliance is to do URL blocking and filtering.Are there any other options we can consider or is it SaaS only. Would have preferred Trend Micro, but don't this is possible with this appliance.Will content security be offered on the Cisco ASA 5500-X Series?At this time, content security services are not supported on the Cisco ASA 5500-X Series appliances. However, the ASA 5500-X Series Cisco Cloud Web Security ready. Cisco Cloud Web Security provides content security as a cloud-based software as a service (SaaS).
View 1 Replies View RelatedI have an ASA5510-BUN-K9 in this version:
###
Cisco Adaptive Security Appliance Software Version 8.0(3)6
Device Manager Version 6.0(2)
Compiled on Thu 17-Jan-08 17:42 by builders
System image file is "disk0:/asa803-6-k8.bin"
Hardware: ASA5510, 202 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
###
The question is what i need to add the CSC10 SSM with content filtering and url filtering to this version of ASA? Do I need more ram? Do I need more flash? Is this version compatible with the CSCSSM hardware? What licenses i need for 100 users?
I have some clarifications regarding ASA firewall, it can be support bandwidth management and content security at the same time. we are looking for below features in ASA5510.
IP/Policy based bandwidth management.Controll the bandwidth and allocate the bandwidth to specified users or servers.Content Security. If not, which device I need to set for Internet Bandwidth Management and content security.
I run a website for a local football team using Serif Webplus X6. On uploading the weekly updates of the site the process seems ok for a few minutes with progress bars showing uploading of files but then it all stops and I have to reset my wireless network adaptor 1703 and it continues but I can't just leave it to work on its own. Device manager says that the drivers are up to date but I'm fed up with having to nurse the adaptor. This didn't happen with previous computers.
View 2 Replies View RelatedI'm new to IT, and have been put in charge of managing our servers hile my boss is on vacation.We currently have a Sonicwall Network Security Appliance that handles our Firewall/VPN and have web content filtering set in place.I have a user who belongs to 2 CFS policy groups that we have set up. I've double checked with Active Directory, and he is a member of both groups.
This person SHOULD have access to Job searches/ and Restaurants,but receives a "content blocked" message on his browser.It appears to me that the settings in Sonicwall are correct, as well with AD member groups.
I have read that nat control is no longer exist in this version,However, I am trying to permit traffic from lower security interface to higher interface security,Is it need to be Natted ?
When I try to route, i have never succeeded, but when I put a nat, I can access and the traffic go through Do I miss anything on the nat control statement ?
Looking for a recommended code on the ASA 5585x firewall. We ran into a bug (CSCtr24705) on version 8.4.2 where it rebooted the primary firewall. The bug has to do with modifying an existing ACL that's part of a custom policy-map inside a service-policy. If we upgrade to 8.4.5 (which has the previous bug fix in it), there is another major bug (CSCud70273) where if you use the packet-tracer input command on an inside interface it causes problems too.
I don't understand why packet-tracer input would have a bug associated with it when it's been around for a long time and we use it on a daily basis for troubleshooting. Is there stable code for the 5585x to upgrade to without running into possibly a major bug? This is our core firewall so there are no VPN tunnels on it. It's setup in active/standby failover in routed mode.
I'm trying to configure TrendMicro IOS content filtering. I have this working on a separate box, running 15.1.
On this particular testbed, I have a 2900 running:
System image file is "flash0:c2900-universalk9-mz.SPA.152-3.T1.bin"
And the following licensing:
Technology Package License Information for Module:'c2900'
Code...
Im currently doing a project, and building a machine/ bastion host with DHCP and a content filter.Its running XP. Any recommendations for the content filter that will run on XP and is also free and popular?
View 1 Replies View RelatedI am wondering what is Latency value for Cisco ASA 5585X and 5555X . I can see on websites that it says "low latency firewall" but I dont see any value.
View 1 Replies View Relatedif there is a way to configure pim-ssm on asa 5585x-ssm20.
View 1 Replies View RelatedLooking to replace an "all-in-one" type firewall (UTM/Firewall, SSL VPN) with a cisco product - the issue i'm running into is that we have multiple ISPs plus WAN and DMZ - overall more than 5 ports on mid-range ASA devices - and from what i read, adding 4-port module precludes me from adding CSC module.
Is there an solution to that other than going for 5585-x model? (kind of over our budget, granted we need 2 for failover)
I have a circuit that will be delivered to a client next week and we are installing an ASA 5585x for them. They will have a circuit coming in with a few VLANs configured on it. One VLAN for the Internet and one for connectivity to another client.
So does the ASA allow you to create the "outside" interface on a subinterface?
I will be supporting a new ASA 5585X running 8.4 and I was wondering if it's possible to apply an ACL globally instead of it as an access group that is applied to a specific interface as in or out ... below are the interfaces and ACl.
View 2 Replies View RelatedBecause ASA5585X doesn't support CSC module, how can do URL filtering on ASA5585X
View 1 Replies View RelatedI want to configure 5585x Active/Standby with 2 nexus switches utilizing VPC technology. New ASA 8.4 supports etherchannel so I want to plugin 2 cables from ASA1 to sw1 and sw2 and 2 cables from ASA2 to sw1 and sw2? Is this a valid design? how would I configure that? Any design document on that?
View 1 Replies View RelatedI have an asa 5585x cluster. I get ssh access but no console access on the standby unit.
On the active unit, when I try console access, ASA ask for a password. I have tried all the one that I have configured, but without success.
We have a 5585X running in multi context mode, and we are getting log entries for scanning threat detection, such as:
%ASA-4-733100: [ Scanning] drop rate-1 exceeded. Current burst rate is 2 per second, max configured rate is 10; Current average rate is 5 per second, max configured rate is 5; Cumulative total count is 3116
Threat detection is not supported in multi context mode so I cannot tune the thresholds, is there any way that I can get rid of this outside of messing about with logging levels/message IDs?
I have a Cisco SR-520 router which I am trying to configure and install the IOS content filter. I have read many of the documents on this but some of the lines do not work, from using the pages belowURL
you are supposed to enter parameter maps as follows:-
parameter-map type trend-global global-param-map
server trps.trendmicro.com
cache-size maximum-memory 256
cache-entry-lifetime 1
The router has 12.4 (20) T4, which is supposed to be supported, the only other way of configuring is using CCP which is not compatible with SR-520's you recieve hardware not supported message's.
I know the 5510 & 5520s support the CSC-SSM module for Content Filtering (Anti-Phishing, Anti Spam, URL filtering, Anti-Spyware & Antivirus), but what about content filtering for the ASA5525-K9.The problem that I have is that I need a firewall that supports up to 1 Gbps Maximum Firewall Throughput and to support 250 users with Content Filtering described above.I'm using the following doc for sizing and came across the ASA5525-K9 for 1 Gbps, but not sure about the Content filtering: url...
View 3 Replies View RelatedI recently had a issue with conecting Cat4500-E switches with SupIV to CAM. I have recieved error message "unable to control x.x.x.x".Whole problem was switch OID not in the database of CAM. For those experiencing the same problem go to on the CAM:
Device Management > Clean Access > Updates > Update CHECK "all" options and RUN UPDATE!
In Cisco ASA Firewall 5510 does the feature content filter come built in?
View 1 Replies View RelatedI seem to be experiencing a problem with content filtering on our 1941, if I add anymore patterns to the policy below the router crashes and requires a reboot, not sure why?
parameter-map type urlfpolicy trend cptrendparacatdeny0
max-request 5000
max-resp-pak 1000
[Code].....
In Cisco ASA Firewall 5510 does the feature content filter come built in?
View 3 Replies View RelatedI have IOS content filtering using the Trend Micro subscription service working on a 2911 running 15.1.(3)T3 with the security license option and a 30 day demo Trend subscription. Once I figured out that the content filtering for Trend appears to be completely broken in 15.2 (even using docs for 15.2) I went back to 15.1 and it works great.
Everything seems great so far except I would like to have a more 'fancy' or custom blocked page where a user can have a couple links to either go to the trend micro reporting page [URL] or some other page, and maybe some branding so they know the page is coming from our network and is not some fake security thing or phishing attempt or whatever.
I know I can use the 'parameter-map type urlf policy trend ' section to do a tiny bit of customization of the text that appears on the default blocked page display and there is an option for it to go to a simple redirect instead ('block-page redirect -url') but how to do more with either the built in page or the redirect- url to keep the information of what page the user was trying to access and why it was blocked (category etc.) while adding more features.
Oh, one last thing, this doesn't support any kind of 'user override' or anything like that does it? So that a network can have a filter applied but an admin could override the filtering to allow temporary access to something?
I am looking at deploying a pair of 5585X's in an active/active multiple context state. I am creating Mulitple contexts that need to be able to route to each other. I was going to deploy a type of Gateway context that has a shared interface to all of the other contexts, instead of sharing interfaces directly between the contexts, i beleive this will work as basically i am just cascadng the contexts and sharing interfaces.
The main problem i have come across, is that if i deploy active/active across two appliances using 2 failover groups i can not see a way to route between them, for example.
I have Context 1, Context 2 and Context GW A including the shared interfaces of Con1 and Con2 in failover group 1 on appliance A with the respective standbys on Appliance 2. I have Context 2, Context 4 and Context GW B including the shared interfaces of Con 3 and Con 4 in failover group 2 on appliance B with the respective standbys on Appliance 1.
I need to be able to route traffic between Context GW A and GW B so that the contexts can communicate in normal operation and in failover. I do not beleive that I can share an interface between contexts in two separate failover groups and to be honest without adding a L3 device between the appliances i am not sure if this is possible.
I face a strange bahavior with my rv220w router : I set up access rules to deny all outbound trafic for a particular IP range. It seems to work fine .... but when I enable content filtering, HTTP access on port 80 works again (and other ports are denied). It seems that activating content filtering makes the router ignore firewall rule.
View 2 Replies View RelatedI found an interesting manual at this forum for blocking websites whits local content filtering. After I've modified the variables to get more details, I stopped at on question. My current Problem is "zone-pair.
zone security Z-SECRUTIY-SOURCE
zone security Z-SECRUTIY-DESTINATION
zone-pair security ZP-SECURITY source Z-SECRUTIY-SOURCE destination Z-SECRUTIY-DESTINATION
service-policy type inspect CM-INSPECT-TRAFFIC
[code]...
I have an ASA 5520 in my company which does all our NAT and Firewall access control. Currently there is a rule in place to allow an incoming connection on port 2222 from a specific ip address to allow access to a web app our developers created. This is a test before the web app is released live. Now the web app can communicate with the specific address and port but the incoming connection on port 2222 isn't getting through. Everything looks great in the firewall but how can I log any hits this ACL takes to identify any potential problems?
View 2 Replies View Related