I will be supporting a new ASA 5585X running 8.4 and I was wondering if it's possible to apply an ACL globally instead of it as an access group that is applied to a specific interface as in or out ... below are the interfaces and ACl.
View 2 Replies
Looking for a recommended code on the ASA 5585x firewall. We ran into a bug (CSCtr24705) on version 8.4.2 where it rebooted the primary firewall. The bug has to do with modifying an existing ACL that's part of a custom policy-map inside a service-policy. If we upgrade to 8.4.5 (which has the previous bug fix in it), there is another major bug (CSCud70273) where if you use the packet-tracer input command on an inside interface it causes problems too.
I don't understand why packet-tracer input would have a bug associated with it when it's been around for a long time and we use it on a daily basis for troubleshooting. Is there stable code for the 5585x to upgrade to without running into possibly a major bug? This is our core firewall so there are no VPN tunnels on it. It's setup in active/standby failover in routed mode.
I am wondering what is Latency value for Cisco ASA 5585X and 5555X . I can see on websites that it says "low latency firewall" but I dont see any value.
View 1 Replies View Relatedif there is a way to configure pim-ssm on asa 5585x-ssm20.
View 1 Replies View RelatedLooking to replace an "all-in-one" type firewall (UTM/Firewall, SSL VPN) with a cisco product - the issue i'm running into is that we have multiple ISPs plus WAN and DMZ - overall more than 5 ports on mid-range ASA devices - and from what i read, adding 4-port module precludes me from adding CSC module.
Is there an solution to that other than going for 5585-x model? (kind of over our budget, granted we need 2 for failover)
I have a circuit that will be delivered to a client next week and we are installing an ASA 5585x for them. They will have a circuit coming in with a few VLANs configured on it. One VLAN for the Internet and one for connectivity to another client.
So does the ASA allow you to create the "outside" interface on a subinterface?
I have a active-active setup with 2 cisco asa 5585x running 8.4 - the boxes ahve each 2 sec context's build-in - which gives 4 sec context in the cluster. I have 2 x 5 extra licenses (2 x ASA5500-SC-5) which I haven't applied yet - will this give me a total of 10 or 14 security contextes? I am a bit in doubt because if I only get 10 sec contextes in this cluster then could I instead get a single 10 security context license (1 x ASA5500-SC-10) and add this - hereby I would get 12 then.
View 1 Replies View RelatedIs it possible have Content Security and Control Security in a ASA 5585-X? I´m asking because the CSC-SSM is only supported in ASA 5540, 5520 and 5510 and I dont know how it feature ca be supported on a new ASA 5585-X.
View 2 Replies View RelatedBecause ASA5585X doesn't support CSC module, how can do URL filtering on ASA5585X
View 1 Replies View RelatedI want to configure 5585x Active/Standby with 2 nexus switches utilizing VPC technology. New ASA 8.4 supports etherchannel so I want to plugin 2 cables from ASA1 to sw1 and sw2 and 2 cables from ASA2 to sw1 and sw2? Is this a valid design? how would I configure that? Any design document on that?
View 1 Replies View RelatedI have an asa 5585x cluster. I get ssh access but no console access on the standby unit.
On the active unit, when I try console access, ASA ask for a password. I have tried all the one that I have configured, but without success.
We have a 5585X running in multi context mode, and we are getting log entries for scanning threat detection, such as:
%ASA-4-733100: [ Scanning] drop rate-1 exceeded. Current burst rate is 2 per second, max configured rate is 10; Current average rate is 5 per second, max configured rate is 5; Cumulative total count is 3116
Threat detection is not supported in multi context mode so I cannot tune the thresholds, is there any way that I can get rid of this outside of messing about with logging levels/message IDs?
I am managing a firewall over remotely in my LAN itself. I started a continous ping to the Firewall IP and the response is less than 1 ms.
While applying some access control list to the firewall via putty ...Suddenly the latency is going hing and it is hitting xxxx ms. And also the acl are getting pasted on the screen by word by word. Sometimes i used to get some RTO for the Firewall IP Address inth eping response.
find the Firewall Version:
Cisco ASA 5510
Version : 7.2
Having more than 600 ACL's.
I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies View RelatedWe apply a new anyconnect mobile license to our primary asa 5520 and the failover feature went into an off state. WE have now applied a second purchased anyconnect mobile to our secondary asa but the failover is still inactive/off.
bcoh1fw50# sh failover state
State Last Failure Reason Date/Time
This host - Primary
Disabled Ifc Failure 14:43:21 EST Jan 30 2013
[Code].....
I have Cisco ASA5510 OS version 8.4(1), when i try to apply static command, this command is not found, the NAT issues used nat(inside,outside).
So why i can't found this command ?
I'm using ASDM 6.2 with a FWSM on a 6500.
At the moment everytime I want to make a change to firewall rules I click apply and the rules are applied Immediately. I have to make multiple changes during the working day which I don't like to do.
What I would like to do is make changes during the day but not apply them until out of hours (some sort of batch mode). Like I can do in my check point firewalls.
Is there a command to globally invoke rw or ro feature of SNMP on a 356024P switch?
View 2 Replies View RelatedI want run IPV6 multicast routing on Cisco 6506 device, I know i can activate IPv6 multicast routing globally but , Is it possible to run ipv6 multicast routing on interface vlan XXXX ?
View 1 Replies View RelatedI am looking at deploying a pair of 5585X's in an active/active multiple context state. I am creating Mulitple contexts that need to be able to route to each other. I was going to deploy a type of Gateway context that has a shared interface to all of the other contexts, instead of sharing interfaces directly between the contexts, i beleive this will work as basically i am just cascadng the contexts and sharing interfaces.
The main problem i have come across, is that if i deploy active/active across two appliances using 2 failover groups i can not see a way to route between them, for example.
I have Context 1, Context 2 and Context GW A including the shared interfaces of Con1 and Con2 in failover group 1 on appliance A with the respective standbys on Appliance 2. I have Context 2, Context 4 and Context GW B including the shared interfaces of Con 3 and Con 4 in failover group 2 on appliance B with the respective standbys on Appliance 1.
I need to be able to route traffic between Context GW A and GW B so that the contexts can communicate in normal operation and in failover. I do not beleive that I can share an interface between contexts in two separate failover groups and to be honest without adding a L3 device between the appliances i am not sure if this is possible.
I have an ASA 5510 in a live environment. Up til a short while ago I could access this via the ASDM and ssh. However I can no longer connect to it via eithier. When I access It via SSH I get a disclaimer saying the following
*** You have entered a restricted zone! Authorized access only!!! Disconnect immediately if you are not authorized user! ***
It then cuts me off.
When I try to access the ASDM I get the following
The firewall is running all its services without a problem and I can ping the device without any issues. Also none of the config (to my knpowledge has been changed). I set up a console session and http server enable is still there with
http 192.168.200.0 255.255.255.0 inside
I'd like to add an RDP to the vpn portal page on our 5585x. Looking for the rdp plugin in the 5585x download area but there is no page for Remote access plugins. Would the plugin be the same as any of the 5500 ASAs? Could I just download the rdp_09.11.2012.jar file from the 5505 download area?
View 1 Replies View RelatedI have CISCO 5510 firewall running with IOS ASA821-k8.bin.My company has purchased another ASA5510 with IOS ASA843-k8.bin.We need to run both firewalls in Active/Standby mode.
If I upgrade the IOS of old firewall to ASA843-k8.bin the the running configurations does not work properly.It does not pick the network objects and NAT rules as they are configured with OLD IOS and running.
Or if I restore the configurations of old firewall at New ASA the result is worst. Even firewall with new IOS does not show any Access Rule and NAT rule and does not supprt network objects.
Starting a project where they customer has ASA 5585X with SSP40 with 10K SSL Premium Lic and ACS5.1.The cust wants IPSec, and Anyconnect Client terminations. The number of users will be close to 6000 and will scale.Due to the huge scale of users, i am not able to finalize a design. Have the following doubts.
1. Will ACS have any issues in supporting a database this huge. OR is it better to go with the AD/LDAP integration.
2. What is the best way to allocation IP address. Does ACS 5.1 support dynamic allocation form an IP pool.
I have been browsing through the forum, couldnt find anything concrete.
We have a pair of ASA 5585X firewalls that need to connect to a pair of Avaya VSP9000 switches. The Cisco docs refer to doing spanned etherchannel with a Cat 6500 switch using VSS or a Nexus switch using VPC. Does spanned etherchannel work with non Cisco switches or is this proprietary? The etherchannel on the ASA is setup using LACP. Here's applicable configuration:
interface TenGigabitEthernet0/6
channel-group 2 mode active vss-id 1
!
interface TenGigabitEthernet0/7
channel-group 2 mode active vss-id 2
!
interface Port-channel2
port-channel span-cluster vss-load-balance
I was going through the release notes on cisco website of ASA 8.4.6 and ASDM 7.1.3 but I just can not find a definitely answer: if ASDM 7.1.3 can run with 8.4.6?
View 2 Replies View RelatedI'm having an issue configuring NAT on an ASA running 8.3. 've managed to configure NAT from the Inside interface to the DMZ, using PAT, so that the traffic is hidden behind the IP of the DMZ interface. This seems to work ok.
object network obj_any-18
subnet 0.0.0.0 0.0.0.0
object network obj_any-18
nat (inside,dmz1.005) dynamic interface
The problem I have is when I try to configure a rule for traffic that originates in the DMZ back to the Inside. I can't seem to get any traffic to flow from the DMZ to the Inside, and sometimes I manage to stop traffic flowing in both directions!
What would be the best way to configure the return traffic from the DMZ to the Inside.
I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies View RelatedWhat would be the command to clear the df-bit on a PIX-515e running 6.3? I have tried the following:
conf t crypto ipsec df-bit clear-df inside and it doesn't take it.
I'm replacing a new ASA 5505 due to a corrupted flash. On the original unit, I had the ability to SSH into the device using TeraTerm with no problems. While configuring the new device, I entered commands to enable SSH into the unit.
View 5 Replies View RelatedI have a Cisco ASA 5520 running 8.2.2 with the VPN Plus license. I am wondering what is the max number of sub-interfaces you can have on a physical interface. I know on the 5505 it was 20 sub-interfaces if you were running the Security Plus license. What is the magic number for the 5520. I have hit 20 sub-interfaces on gi0/1 interface and now I am starting to run into problems with sub-interface #21.
View 1 Replies View RelatedI have VPN up and running between two sites. Both sites have Cisco ASA 5505. I can ping across the devices from both networks. But I cannot remote into the servers on the other network.
View 8 Replies View RelatedI Have an asa 5510 running code 7.2 configured with ssl vpn,ssl vpn users able to connect to to portal which i have configured with the required resources,but the thing is that these ssl users unable to upload files to cifs shared directory , although they have full access to the shared folder
View 0 Replies View Related
